BMP estimation of landfilled municipal solid waste by multivariate statistical methods using specific waste parameters: case study of a sanitary landfill in Turkey

The main objective of this study was to determine whether methane potential of waste could be estimated more easily by a limited number of waste characterization variables. 36 samples were collected from 12 locations and 3 waste depths in order to represent almost all waste ages at the landfill. Actual remaining methane potential of all samples was determined by the biochemical methane potential (BMP) tests. The cumulative methane production of closed landfill (cLF) samples reached 75–125 mL at the end of experiment duration, while the samples from active landfill (aLF) produced in average 216–266 mL methane. The average experimental k and L ₀ values of cLF and aLF were determined by non-linear regression using BMP data with first-order kinetic equation as 0.0269 day^?1–30.38 mL/g dry MSW and 0.0125 day^?1–102.1 mL/g dry MSW, respectively. The principal component analysis (PCA) was applied to analyze the results for cLF and aLF along with BMP results. Three PCs for the data set were extracted explaining 72.34 % variability. The best MLR model for BMP prediction was determined for seven variables (pH–Cl–TKN–NH4–TOC–LOI–Ca). R ² and Adj. R ² values of this best model were determined as 80.4 and 75.3 %, respectively.     

Temporal variability of soil gas composition in landfill covers

In order to assess the temporal variability of the conditions for the microbial oxidation of methane in landfill cover soils and their driving variables, gas composition at non-emissive and strongly emissive locations (hotspots) was monitored on a seasonal, daily and hourly time scale on an old, unlined landfill in northern Germany. Our study showed that the impact of the various environmental factors varied with the mode of gas transport and with the time scale considered. At non-emissive sites, governed by diffusive gas transport, soil gas composition was subject to a pronounced seasonal variation. A high extent of aeration, low methane concentrations and a high ratio of CO₂ to CH₄ were found across the entire depth of the soil cover during the warm and dry period, whereas in the cool and moist period aeration was less and landfill gas migrated further upward. Statistically, variation in soil gas composition was best explained by the variation in soil temperature. At locations dominated by advective gas transport and showing considerable emissions of methane, this pattern was far less pronounced with only little increase in the extent of aeration during drier periods. Here, the change of barometric pressure was found to impact soil gas composition. On a daily scale under constant conditions of temperature, gas transport at both types of locations was strongly impacted by the change in soil moisture. On an hourly scale, under constant conditions of temperature and moisture, gas migration was impacted most by the change in barometric pressure. It was shown that at diffusion-dominated sites complete methane oxidation was achieved even under adverse wintry conditions, whereas at hotspots, even under favorable dry and warm conditions, aerobic biological activity can be limited to the upper crust of the soil.     

Evaluation of the potential methane yield of industrial wastewaters used in bioreactor landfills

To increase the moisture content of waste disposed in a bioreactor landfill, it is critical to secure the moisture source. In this study, industrial wastewater was evaluated as a potential moisture source for a bioreactor landfill with respect to the impact on methane generation. Industrial wastewater samples were collected from fishery, brewery and dairy industries. These samples were tested for basic water chemistry parameters, heavy metals, and methane generation using the regular and modified biochemical methane potential (BMP) assays. Despite high sodium and total phosphate concentrations in the fishery wastewater, a significant methane yield was observed (0.313?m³ CH₄/kg COD). However, a relatively large amount of fishery wastewater added at the phase of methane generation acceleration adversely affected microbial activity. Samples from the brewery and dairy wastewater did not indicate significant inhibitory effects on methane generation in either the regular or the modified BMP assay. This study demonstrates the utility of wastewater as an alternative to traditional moisture sources when used to enhance methane production in a bioreactor landfill.     

Life cycle assessment of four municipal solid waste management scenarios in China

A life cycle assessment was carried out to estimate the environmental impact of municipal solid waste. Four scenarios mostly used in China were compared to assess the influence of various technologies on environment: (1) landfill, (2) incineration, (3) composting plus landfill, and (4) composting plus incineration. In all scenarios, the technologies significantly contribute to global warming and increase the adverse impact of non-carcinogens on the environment. The technologies played only a small role in the impact of carcinogens, respiratory inorganics, terrestrial ecotoxicity, and non-renewable energy. Similarly, the influence of the technologies on the way other elements affect the environment was ignorable. Specifically, the direct emissions from the operation processes involved played an important role in most scenarios except for incineration, while potential impact generated from transport, infrastructure and energy consumption were quite small. In addition, in the global warming category, highest potential impact was observed in landfill because of the direct methane gas emissions. Electricity recovery from methane gas was the key factor for reducing the potential impact of global warming. Therefore, increasing the use of methane gas to recover electricity is highly recommended to reduce the adverse impact of landfills on the environment.     

Effects of lipid concentration on anaerobic co-digestion of municipal biomass wastes

The influence of the lipid concentration on the anaerobic co-digestion of municipal biomass waste and waste-activated sludge was assessed by biochemical methane potential (BMP) tests and by bench-scale tests in a mesophilic semi-continuous stirred tank reactor. The effect of increasing the volatile solid (VS) concentration of lipid from 0% to 75% was investigated. BMP tests showed that lipids in municipal biomass waste could enhance the methane production. The results of bench-scale tests showed that a lipids concentration of 65% of total VS was the inhibition concentration. Methane yields increased with increasing lipid concentration when lipid concentrations were below 60%, but when lipid concentration was set as 65% or higher, methane yields decreased sharply. When lipid concentrations were below 60%, the pH values were in the optimum range for the growth of methanogenic bacteria and the ratios of volatile fatty acid (VFA)/alkalinity were in the range of 0.2–0.6. When lipid concentrations exceeded 65%, the pH values were below 5.2, the reactor was acidized and the values of VFA/alkalinity rose to 2.0. The amount of Brevibacterium decreased with increasing lipid content. Long chain fatty acids stacked on the methanogenic bacteria and blocked the mass transfer process, thereby inhibiting anaerobic digestion.     

BMP tests of source selected OFMSW to evaluate anaerobic codigestion with sewage sludge

The aim of this study is to characterize different types of source selected organic fraction of municipal solid waste (SS-OFMSW) in order to optimize the upgrade of a sewage sludge anaerobic digestion unit by codigestion. Various SS-OFMSW samples were collected from canteens, supermarkets, restaurants, households, fruit–vegetable markets and bakery shops. The substrates characterization was carried out getting traditional chemical–physical parameters, performing elemental analysis and measuring fundamental anaerobic digestion macromolecular compounds such as carbohydrates, proteins, lipids and volatile fatty acids. Biochemical methane potential (BMP) tests were conducted at mesophilic temperature both on single substrates and in codigestion regime with different substrates mixing ratios. The maximum methane yield was observed for restaurant (675 NmlCH₄/gVS) and canteens organic wastes (571 and 645 NmlCH₄/gVS). The best codigestion BMP test has highlighted an increase of 47% in methane production respect sewage sludge digestion.     

Potential methane yield of food waste/food waste leachate from the biogasification facilities in South Korea

This study was to find out potential of methane yield on food waste and food waste leachate as biomass in Korea. The seven biogasification facilities were selected for comparison of theoretical methane yield and actual methane yield. The theoretical methane yield was calculated based on organic constituents (carbohydrate, protein, fat) and based on element analysis. The actual methane yield was investigated based on volatile solids and CODcr. Theoretical methane yields by organic constituents were 0.52 Sm³CH₄/kg VS and 0.35 Sm³CH₄/kg CODcr and these by element analysis were 0.53 Sm³CH₄/kg VS and 0.36 Sm³CH₄/kg CODcr. Actual methane yields were 0.36 Sm³CH₄/kg VS_in and 0.26 Sm³CH₄/kg CODcr_in. Considering the average removal efficiency of organic materials of seven FWL biogasification facilities, actual methane yields were 0.48 Sm³CH₄/kg VS_rem and 0.33 Sm³CH₄/kg CODcr_rem. Methane yield by organic constituents is very similar to that by element analysis and actual methane yields of volatile solids and CODcr were similar to theoretical value. The actual methane yield in this study showed approximated boundary values with previous other references which conducted in lab-scale or biochemical methane potential (BMP) tests. In conclusion, Korean food waste and food waste leachate have sufficient potential of methane yield in the ongoing biogasification facilities.     

Analysis on biochemical methane potential of agricultural byproducts with different types of silage storage

The aim of this work is to estimate biogas production by anaerobic digestion of agricultural byproduct silage at the low carbon green village in South Korea. The composition of agricultural byproduct from hot pepper farms was analyzed and it was found to be favorable with anaerobic digestion. In the cases of silage materials, the theoretical methane potentials of all of the ensiled materials were increased with silage storage having an increased range from 103 to 120 % compared to that without ensiling. The biochemical methane potential (BMP) tests showed that the ultimate methane potential of ensiled material was measured to be higher than that of raw material without silage storage, while the first order hydrolysis constant was lower. All of the silage materials containing microbial additives used in this study showed higher ultimate methane potentials and first order hydrolysis constants than raw material and silage material without additives. The change of ultimate methane potential was analyzed over time, and all of the test materials, except Day 2, showed higher ultimate methane potential than raw material, Day 0, and the highest was found on Day 40.     

Assessment of the aerobic preparation and bottom ash addition as pretreatment steps before landfilling: Impact on methanogenesis kinetics and leachate parameters

This work focuses on assessing the impact of two types of waste pretreatment: addition of bottom ashes and aerobic pretreatment on both the onset and kinetics of methanogenesis and the evolution of different parameters in the leachate. It also studies the correlation between methane production and the different parameters measured in the leachate produced. A total of six 68-L pilots were thus used with fresh municipal solid waste (MSW) shredded to a 40-mm size. After 14months of landfilling, the control has produced less than 10NLkg(-1)DM, which corresponds to around 7% of its biochemical methane potential (BMP). Nevertheless, on one hand for aerobically pretreated waste, the lag phase before the onset of methanogenesis is significantly reduced to 0.9month compared to more than 1year for the control. In addition to that, on average 110NLkg(-1)DM (90% of the BMP) is produced within around 6.5months. On the other hand, the waste with added bottom ash shows a slight improvement of the lag phase over the control for one of the duplicate: 6.1months of lag phase. At this stage, on average of 26NLkg(-1)DM waste are detected (22% of the BMP) no final conclusion concerning the impact of bottom ashes could be made. The data obtained for the leachate parameters agrees with the observations on methane production. Statistical correlation study shows that the two components of the corrected PCA interpret 76% of the variability of the data: SUVA (specific UV absorbance at 254nm) and HPI(*) (% of hydrophilic compounds) are identified as interesting parameters for following up the biodegradation in landfill conditions.     

Evaluating the biochemical methane potential (BMP) of low-organic waste at Danish landfills

The biochemical methane potential (BMP) is an essential parameter when using first order decay (FOD) landfill gas (LFG) generation models to estimate methane (CH₄) generation from landfills. Different categories of waste (mixed, shredder and sludge waste) with a low-organic content and temporarily stored combustible waste were sampled from four Danish landfills. The waste was characterized in terms of physical characteristics (TS, VS, TC and TOC) and the BMP was analyzed in batch tests. The experiment was set up in triplicate, including blank and control tests. Waste samples were incubated at 55 °C for more than 60 days, with continuous monitoring of the cumulative CH₄ generation. Results showed that samples of mixed waste and shredder waste had similar BMP results, which was in the range of 5.4–9.1 kg CH₄/ton waste (wet weight) on average. As a calculated consequence, their degradable organic carbon content (DOCC) was in the range of 0.44–0.70% of total weight (wet waste). Numeric values of both parameters were much lower than values of traditional municipal solid waste (MSW), as well as default numeric values in current FOD models. The sludge waste and temporarily stored combustible waste showed BMP values of 51.8–69.6 and 106.6–117.3 kg CH₄/ton waste on average, respectively, and DOCC values of 3.84–5.12% and 7.96–8.74% of total weight. The same category of waste from different Danish landfills did not show significant variation. This research studied the BMP of Danish low-organic waste for the first time, which is important and valuable for using current FOD LFG generation models to estimate realistic CH₄ emissions from modern landfills receiving low-organic waste.     

Methane emissions from MBT landfills

Within the scope of an investigation for the German Federal Environment Agency (“Umweltbundesamt”), the basics for the estimation of the methane emissions from the landfilling of mechanically and biologically treated waste (MBT) were developed. For this purpose, topical research including monitoring results regarding the gas balance at MBT landfills was evaluated.For waste treated to the required German standards, a methane formation potential of approximately 18–24 m³ CH₄/t of total dry solids may be expected. Monitoring results from MBT landfills show that a three-phase model with differentiated half-lives describes the degradation kinetics in the best way. This is due to the fact that during the first years of disposal, the anaerobic degradation processes still proceed relatively intensively. In addition in the long term (decades), a residual gas production at a low level is still to be expected.Most of the soils used in recultivation layer systems at German landfills show a relatively high methane oxidation capacity up to 5 l CH₄/(m² h). However, measurements at MBT disposal sites indicate that the majority of the landfill gas (in particular at non-covered areas), leaves the landfill body via preferred gas emission zones (hot spots) without significant methane oxidation. Therefore, rather low methane oxidation factors are recommended for open and temporarily covered MBT landfills. Higher methane oxidation rates can be achieved when the soil/recultivation layer is adequately designed and operated.Based on the elaborated default values, the First Order Decay (FOD) model of the IPCC Guidelines for National Greenhouse Gas Inventories, 2006, was used to estimate the methane emissions from MBT landfills. Due to the calculation made by the authors emissions in the range of 60,000–135,000 t CO_2-eq./a for all German MBT landfills can be expected. This wide range shows the uncertainties when the here used procedure and the limited available data are applied. It is therefore necessary to generate more data in the future in order to calculate more precise methane emission rates from MBT landfills. This is important for the overall calculation of the climate gas production in Germany which is required once a year by the German Government.     

Characterizing food waste substrates for co-digestion through biochemical methane potential (BMP) experiments

Co-digestion of food waste with dairy manure is increasingly utilized to increase energy production and make anaerobic digestion more affordable; however, there is a lack of information on appropriate co-digestion substrates. In this study, biochemical methane potential (BMP) tests were conducted to determine the suitability of four food waste substrates (meatball, chicken, cranberry and ice cream processing wastes) for co-digestion with flushed dairy manure at a ratio of 3.2% food waste and 96.8% manure (by volume), which equated to 14.7% (ice-cream) to 80.7% (chicken) of the VS being attributed to the food waste. All treatments led to increases in methane production, ranging from a 67.0% increase (ice cream waste) to a 2940% increase (chicken processing waste) compared to digesting manure alone, demonstrating the large potential methane production of food waste additions compared to relatively low methane production potential of the flushed dairy manure, even if the overall quantity of food waste added was minimal.     

Experimental and life cycle assessment analysis of gas emission from mechanically–biologically pretreated waste in a landfill with energy recovery

The global gaseous emissions produced by landfilling the Mechanically Sorted Organic Fraction (MSOF) with different weeks of Mechanical Biological Treatment (MBT) was evaluated for an existing waste management system. One MBT facility and a landfill with internal combustion engines fuelled by the landfill gas for electrical energy production operate in the waste management system considered. An experimental apparatus was used to simulate 0, 4, 8 and 16 weeks of aerobic stabilization and the consequent biogas potential (Nl/kg) of a large sample of MSOF withdrawn from the full-scale MBT. Stabilization achieved by the waste was evaluated by dynamic oxygen uptake and fermentation tests. Good correlation coefficients (R²), ranging from 0.7668 to 0.9772, were found between oxygen uptake, fermentation and anaerobic test values. On the basis of the results of several anaerobic tests, the methane production rate k (year^?1) was evaluated. k ranged from 0.436 to 0.308 year^?1 and the bio-methane potential from 37 to 12 N m³/tonne, respectively, for the MSOF with 0 and 16 weeks of treatment. Energy recovery from landfill gas ranged from about 11 to 90 kW h per tonne of disposed MSOF depending on the different scenario investigated. Life cycle analysis showed that the scenario with 0 weeks of pre-treatment has the highest weighted global impact even if opposite results were obtained with respect to the single impact criteria. MSOF pre-treatment periods longer than 4 weeks showed rather negligible variation in the global impact of system emissions.     

Preliminary environmental impact assessment of PFOS waste treatment in a lab-scale batch subcritical water decomposition operation

Life cycle assessment (LCA) was carried out by SimaPro 7.3 to study the environmental impact of a lab-scale batch subcritical water decomposition operation for a kilogram of Perfluorooctane sulfonic acid (PFOS) waste treatment in this study, a proven process for the decomposition of PFOS pollutants with high concentration. This LCA focuses on not only the main environmental factors from emissions of toxic pollutants, but also the influence from technical characteristics of the iron-induced subcritical water technology including energy and substances consumption during the subcritical water decomposition treatment process. The IMPACT 2002+ environmental model was used to evaluate the 15 midpoint and 4 end-point environmental damages. It was found that the energy consumption to sustain the high temperature (350 °C) and high pressure (23 MPa) in the subcritical water process contributes 99.8 % of the damages. The total negative impact of the SCWD process for 1 kg of PFOS waste treatment to human health, ecological quality, climate change and resources amounts to 1.11 × 10^?3, 8.43 × 10^?5, 9.76 × 10^?4, 9.05 × 10^?4 Pt, respectively. And the improvement of energy efficiency and catalytic effectiveness are two important factors to reduce the environmental impact from the SCWD process for the treatment of PFOS waste.     

Energy recovery from grass using two-phase anaerobic digestion

Municipal solid wastes are major sources of air, water and soil contamination. There is a need for alternative waste management techniques to better utilize the waste and minimize its adverse environmental impact. A two-phase pilot-scale bio-fermentation system was used to evaluate the feasibility of producing methane from grass waste, a major constituent of solid wastes. The bi-phasic system consists of a solid phase and a methane phase. Leachate is re-circulated through the solid phase until a desired level of volatile fatty acid (VFA) is accumulated in the leachate. The leachate is then transferred to the methane reactor where the VFA is converted to methane. The results showed that 67% of the volatile solids in the waste can be converted into soluble chemical oxygen demand in a period of six months. The system produced an average of 0.15 m3 of methane per kg of grass. The average methane concentration in the produced gas was 71%. A mathematical model was developed to estimate the methane and carbon dioxide concentrations in the gas phase as a function of reactor properties.     

Environmental assessment of sewage sludge as secondary raw material in cement production--a case study in China

A life cycle assessment was carried out to estimate the environmental impact of sewage sludge as secondary raw material in cement production. To confirm and add credibility to the study, uncertainty analysis was conducted. Results showed the impact generated from respiratory inorganics, terrestrial ecotoxicity, global warming, and non-renewable energy categories had an important contribution to overall environmental impact, due to energy, clinker, and limestone production stages. Also, uncertainty analysis results showed the technology of sewage sludge as secondary raw material in cement production had little or no effect on changing the overall environmental potential impact generated from general cement production. Accordingly, using the technology of sewage sludge as secondary raw material in cement production is a good choice for reducing the pressure on the environment from dramatically increased sludge disposal. In addition, increasing electricity recovery rate, choosing natural gas fired electricity generation technology, and optimizing the raw material consumption in clinker production are highly recommended to reduce the adverse effects on the environment.     

Passive drainage and biofiltration of landfill gas: Australian field trial

In Australia a significant number of landfill waste disposal sites do not incorporate measures for the collection and treatment of landfill gas. This includes many old/former landfill sites, rural landfill sites, non-putrescible solid waste and inert waste landfill sites, where landfill gas generation is low and it is not commercially viable to extract and beneficially utilize the landfill gas. Previous research has demonstrated that biofiltration has the potential to degrade methane in landfill gas, however, the microbial processes can be affected by many local conditions and factors including moisture content, temperature, nutrient supply, including the availability of oxygen and methane, and the movement of gas (oxygen and methane) to/from the micro-organisms. A field scale trial is being undertaken at a landfill site in Sydney, Australia, to investigate passive drainage and biofiltration of landfill gas as a means of managing landfill gas emissions at low to moderate gas generation landfill sites. The design and construction of the trial is described and the experimental results will provide in-depth knowledge on the application of passive gas drainage and landfill gas biofiltration under Sydney (Australian) conditions, including the performance of recycled materials for the management of landfill gas emissions.     

油田储油罐非甲烷总挥发实验及仿真模拟

针对油田单井拉油罐非密封生产带来的油气泄漏问题,建立小型原油储油罐挥发损耗实验模拟平台,通过气相色谱法探究各因素对其损耗的影响,利用Fluent仿真软件模拟储油罐的泄漏扩散。结果表明:储液温度和有无风环境对储油罐非甲烷总烃(NMHC)挥发影响较大,储液高度和环境温度对其影响较小;仿真模拟无风环境下,储油罐泄漏口短时间内存在油气积聚现象;有风环境下,当风速为1 m/s,油气积聚不明显;随风速增大,扩散浓度场面积不断增大,油品损耗量增大,在风速为5 m/s的环境下,扩散300 s时的浓度场面积相比扩散200 s时较小,但泄漏口处的油气积聚面积增大。     

A dynamic simulation of methane fermentation process receiving heterogeneous food wastes and modelling acidic failure

Microbial response on volatile fatty acids (VFAs) is a key for methane fermentation processes since accumulation of VFAs often causes an acidic failure, especially treating such organics as food wastes composed of mostly readily biodegradable materials. To evaluate the impact of VFA accumulation, a lab-scale continuous experiment was performed for 110 days with sequential feeding of heterogeneous food wastes. When the volumetric loading rate was increased from 6 to 8 kg-COD/m³/day, a sudden decrease of methane production was observed with an accumulation of acetate and propionate in the fermenter. After discontinuation of feeding for 10 days, the digestate in the fermenter was centrifuged and washed with tap water to reduce the VFAs to be acceptable concentration below 1000 mg-COD/L. Nevertheless, no recovery of methane production was observed and VFA concentrations consistently increased. To model the event, a modification of ADM1 was made assuming the methanogens in the fermenter were irreversibly inactivated under very high VFA. Also considering the different nature of the fed food wastes over 11 samples, decomposition kinetics of individual food wastes were manipulated. The modified ADM1 with methanogenic activity decay reasonably reproduced the responses for soluble material concentrations and methane gas production rate over the experimental period.     

Environmental assessment and accounting for the waste disposal stream in Bangkok,Thailand

It is very important that waste should be controlled and appropriately handled in a waste disposal stream, considering its impact on the environment. In this research, the LCA-EA model was applied to the current waste disposal stream of the BMR as well as other waste disposal stream scenarios, so that treatment cost, environmental load and environmental cost were assessed quantatively. The results of this study showed that in the current waste diposal stream in Bangkok, there were large contributions from carbon dioxide and methane to the greenhouse gas emissions from the stream. The study was able to quantify the reductions in environmental load associated with various waste disposal stream scenarios, using the baseline scenario as a standard.