Separation of polycarbonate and acrylonitrile–butadiene–styrene waste plastics by froth flotation combined with ammonia pretreatment

The objective of this research is flotation separation of polycarbonate (PC) and acrylonitrile–butadiene–styrene (ABS) waste plastics combined with ammonia pretreatment. The PC and ABS plastics show similar hydrophobicity, and ammonia treatment changes selectively floatability of PC plastic while ABS is insensitive to ammonia treatment. The contact angle measurement indicates the dropping of flotation recovery of PC is ascribed to a decline of contact angle. X-ray photoelectron spectroscopy demonstrates reactions occur on PC surface, which makes PC surface more hydrophilic. Separation of PC and ABS waste plastics was conducted based on the flotation behavior of single plastic. At different temperatures, PC and ABS mixtures were separated efficiently through froth flotation with ammonia pretreatment for different time (13 min at 23 °C, 18 min at 18 °C and 30 min at 23 °C). For both PC and ABS, the purity and recovery is more than 95.31% and 95.35%, respectively; the purity of PC and ABS is up to 99.72% and 99.23%, respectively. PC and ABS mixtures with different particle sizes were separated effectively, implying that ammonia treatment possesses superior applicability.     

Combination of three-stage sink-float method and selective flotation technique for separation of mixed post-consumer plastic waste

The aim of this research was to separate the different plastics of a mixed post-consumer plastic waste by the combination of a three-stage sink-float method and selective flotation. By using the three-stage sink-float method, six mixed-plastic wastes, belonging to the 0.3-0.5 cm size class and including high density polyethylene (HDPE), polypropylene (PP), polyvinylchloride (PVC), polystyrene (PS), polyethylene terephthalate (PET) and acrylonitrile-butadiene-styrene copolymers (ABS) were separated into two groups, i.e., a low density plastic group (HDPE and PP) and a high density plastic group (PET, PVC, PS and ABS) by tap water. Plastic whose density is less than that of the medium solution floats to the surface, while the one whose density is greater than that of the medium solution sinks to the bottom. The experimental results elucidated that complete separation of HDPE from PP was achieved by the three-stage sink-float method with 50% v/v ethyl alcohol. To succeed in the separation of a PS/ABS mixture from a PET/PVC mixture by the three-stage sink-float method, a 30% w/v calcium chloride solution was employed. To further separate post-consumer PET/PVC and PS/ABS based on plastic type, selective flotation was carried out. In order to succeed in selective flotation separation, it is necessary to render hydrophilic the surface of one or more species while the others are kept in a hydrophobic state. In flotation studies, the effects of wetting agent, frother, pH of solution and electrolyte on separation were determined. The selective flotation results showed that when using 500 mg l(-1) calcium lignosulfonate, 0.01 ppm MIBC, and 0.1 mg l(-1) CaCl2 at pH 11, PET could be separated from PVC. To separate ABS from PS, 200 mg l(-1) calcium lignosulfonate and 0.1 mg l(-1) CaCl2 at pH 7 were used as a flotation solution. Wettability of plastic increases when adding CaCl2 and corresponds to a decrease in its contact angles and to a reduction in the recovery of plastic in the floated product.     

Application of dissolved air flotation on separation of waste plastics ABS and PS

The aim of this research was to separate waste plastics acrylonitrile butadiene styrene (ABS) and polystyrene (PS) by dissolved air flotation in a self-designed dissolved air flotation apparatus. The effects of wetting agents, frother, conditioning time and flotation time on flotation behavior of waste plastics ABS (w-ABS) and PS (w-PS) were investigated and the optimized separation conditions were obtained. The results showed that when using 25 mgL(-1) tannic acid, 5 mgL(-1) terpineol, 15 min conditioning time and 15 min flotation time, mixtures of w-ABS and w-PS were separated successfully by dissolved air flotation in two stages, the results revealed that the purity and recovery rate of w-PS in the floated products were 90.12% and 97.45%, respectively, and the purity and recovery rate of w-ABS in the depressed products were 97.24% and 89.38%, respectively. Based on the studies of wetting mechanism of plastic flotation, it is found that the electrostatic force and hydrophobic attraction cannot be the main factor of the interaction between wetting agent molecules and plastic particles, which can be completed through water molecules as a mesophase, and a hydrogen bonding adsorption model with hydration shell as a mesophase was proposed.     

New characterisation method of electrical and electronic equipment wastes (WEEE)

Innovative separation and beneficiation techniques of various materials encountered in electrical and electronic equipment wastes (WEEE) is a major improvement for its recycling. Mechanical separation-oriented characterisation of WEEE was conducted in an attempt to evaluate the amenability of mechanical separation processes. Properties such as liberation degree of fractions (plastics, metals ferrous and non-ferrous), which are essential for mechanical separation, are analysed by means of a grain counting approach. Two different samples from different recycling industries were characterised in this work. The first sample is a heterogeneous material containing different types of plastics, metals (ferrous and non-ferrous), printed circuit board (PCB), rubber and wood. The second sample contains a mixture of mainly plastics. It is found for the first sample that all aluminium particles are free (100%) in all investigated size fractions. Between 92% and 95% of plastics are present as free particles; however, 67% in average of ferromagnetic particles are liberated. It can be observed that only 42% of ferromagnetic particles are free in the size fraction larger than 20 mm. Particle shapes were also quantified manually particle by particle. The results show that the particle shapes as a result of shredding, turn out to be heterogeneous, thereby complicating mechanical separation processes. In addition, the separability of various materials was ascertained by a sink–float analysis and eddy current separation. The second sample was separated by automatic sensor sorting in four different products: ABS, PC–ABS, PS and rest product. The fractions were characterised by using the methodology described in this paper. The results show that the grade and liberation degree of the plastic products ABS, PC–ABS and PS are close to 100%. Sink–float separation and infrared plastic identification equipment confirms the high plastic quality. On the basis of these findings, a global separation flow sheet is proposed to improve the plastic separation of WEEE.     

Surface ozonation of polyvinyl chloride for its separation from waste plastic mixture by froth floatation

Selective surface modification of polyvinyl chloride (PVC) by ozonation was evaluated to facilitate the separation of PVC from other heavy plastics with almost the same density as PVC, especially polyethylene terephthalate (PET), by the froth flotation process. The optimum froth flotation conditions were investigated, and it was found that at 40°C, 90% of PVC and PET plastics floated. The bubble size became larger and the area covered with bubbles on the plastic surface was reduced with increasing temperature. Optimum PVC separation was achieved with the flotation solution at 40°C and mixing at 180–200 rpm, even for sheet samples 10 mm in size. Combined treatment by ozonation and froth flotation is a simple, effective, and inexpensive method for PVC separation from waste plastics.     

Flame treatment for the selective wetting and separation of PVC and PET

Flame treatment has been used for many years to modify the surface of plastics to allow coatings to be added. The effect of the treatment is to produce hydrophilic species on the surface of the plastic making it water-wettable. The production of hydrophilic plastic surfaces is also required in the selective separation of plastics by froth flotation. For the process to be selective one plastic must be rendered hydrophilic while another remains hydrophobic. In this study the potential for separation of PVC and PET has been investigated. Flame treatment was shown to be very effective in producing a hydrophilic surface on both plastics, although the process was not selective under the conditions investigated. Raising the temperature of the plastics above their softening point produced a hydrophobic recovery. As the softening point of PVC was significantly lower than for PET it was possible to produce a significant difference in hydrophobicity, as judged using contact angle measurement. When immersed in water the contact angle of the PVC was found to be strongly dependent on the pH. Good separation efficiency of the two plastics was achieved by froth flotation from pH 4 to 9. One particular advantage of the technique is that no chemical reagents may be required in the flotation stage. The practicalities of designing a flake treatment system however have to be addressed before considering it to be a viable industrial process.     

Flotability and flotation separation of polymer materials modulated by wetting agents

The surface free energy, surface tension and contact angles were performed to investigate the properties of wetting agents. Adsorption of wetting agents changes wetting behavior of polymer resins. Flotability of polymer materials modulated by wetting agents was studied, and wetting agents change significantly flotability of polymer materials. The flotability decreases with increasing the concentration of wetting agents, and the wetting ability is lignin sulfonate (LS) > tannic acid (TA) > methylcellulose (MC) > triton X-100 (TX-100) (from strong to weak). There is significant difference in the flotability between polymer resins and plastics due to the presence of additives in the plastics. Flotation separation of two-component and multicomponent plastics was conducted based on the flotability modulated by wetting agents. The two-component mixtures can be efficiently separated using proper wetting agent through simple flotation flowsheet. The multicomponent plastic mixtures can be separated efficiently through multi-stage flotation using TA and LS as wetting agents, and the purity of separated component was above 94%, and the recovery was more than 93%.     

Investigation of hydrocyclones for the separation of shredded fridge plastics

The recycling of fridges produces a mixed plastic product of limited value. In order to maximise its value, the separation of the individual polymers that include high impact polystyrene (HIPS), acrylonitrile butadiene styrene (ABS), polyvinyl chloride (PVC) and polyethylene (PE) must take place. The effectiveness of a hydrocyclone system for the separation of these plastics, using both water and calcium chloride solutions, has been investigated. In addition a qualitative procedure for the determination of the HIPS content of a mixed ABS/HIPS product, by selective dissolution in R-limonene, has been developed. It was found that the effective density of separation depended on the particle size and aspect ratio. As the particle size and aspect ratio decreased, the separation became more efficient and the offset between separation density and hydrocyclone medium density decreased. This suggests that, for efficient density separation, closely sized, fine plastic fractions are required. Using these criteria, it was found that the removal of high density plastic such as PVC was readily achieved using a hydrocyclone. A partial separation of HIPS from ABS was found to be possible, taking advantage of a small density difference, using a hydrocyclone medium density of 1035kgm(-3).     

Application of fluidization to separate packaging waste plastics

The objective of the experimental work described in this paper is the study of the separation of PS (polystyrene) from PET (polyethylene terephthalate) and PVC (polyvinyl chloride) from drop-off points using a fluidized bed separator. This is a low-cost process commonly used in the hydro-classification of mineral ores. Firstly, experimental tests were carried out with artificial granulated samples with different grain sizes, types and sources of plastic ("separability tests"). The particle settling velocities were determined under different operating conditions. Then, based on the results, the laboratory tests continued with real mixtures of waste plastics ("separation tests") and the efficiency of the process was evaluated. From a PET-rich mixture, a concentrate of PS with a 75% grade in PS was produced while the underflow was quite clear from PS (grade less than 0.5% in PS).     

A new approach to metal- and polymer-recovery from metallized plastic waste using mechanical treatment and subcritical solvents

Galvanized or “chromium-plated” plastics are well known to the consumer from the automotive sector and sanitary area. Polymers such as acrylonitrile butadiene styrene (ABS) are typically coated with a layer system of chromium, nickel and copper to obtain the characteristic optical surface and resistance properties. Due to the complex manufacturing process and high quality requirements, the production of these plastic metal composites generates 10–30% of rejects. We, therefore, developed an innovative process cascade for the recovery of both components (metal and polymer) applying established technologies (mechanical pre-treatment, classification, melt filtration, CreaSolv^® Process) and were able to obtain ABS regranulate having excellent properties regarding the characteristic values for strength but slight compromises in impact characteristics. Blends with different amounts of virgin ABS, virgin PC and recycled ABS material as well as the pure cases were successfully re-metallized, all of them passing adhesion test, thermal shock resistance and CASS test. The high purity of the recovered materials led to increased redemption prices for metal and polymer by a factor of 6 and 2.5, respectively. Thus, the value added of metallized plastic waste is maximized, revealing a highly positive economic prognosis of a commercial implementation of the developed process—even at moderate scale.     

Processing plastics from ASR/ESR waste: separation of poly vinyl chloride (PVC) by froth flotation after microwave-assisted surface modification

The feasibility of the selective surface hydrophilization of poly vinyl chloride (PVC) using microwave treatment to facilitate the separation of PVC via froth flotation from automobile shredder residue (ASR) and electronic waste shredder residue (ESR) was evaluated. In the presence of powder-activated carbon (PAC), 60-s microwave treatment selectively enhanced the hydrophilicity of the PVC surface (i.e., the PVC contact angle decreased from 86.8° to 69.9°). The scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) results are consistent with increased hydrophilic functional groups (i.e., ether, hydroxyl, and carboxyl), amounting to significant changes in the morphology and roughness of the PVC surface after treatment. After only 60 s of microwave treatment, 20 % of the PVC was separated in virgin and ASR/ESR plastics with 33 and 29 % purity, respectively, as settled fractions by froth flotation at a 150 rpm mixing speed. The microwave treatment with the addition of PAC had a synergetic effect with the froth flotation, which brought about 100 and 90 % selective separation of PVC from the other virgin and ASR/ESR plastics, with 91 and 82 % purity. The use of the combined froth flotation and microwave treatments is an effective technology for separating PVC from hazardous waste plastics.     

Floatability of polymer materials modulated by frothers

Flotation tests of 35 polymer materials were carried out to investigate their floatability modulated by frothers. Results of flotation tests demonstrated that polymer resins and soft PVC showed high floatability, floatability of hard PVC plastics was relatively low and was related to the frothers, and there exists significant difference in the floatability of different post-consumer plastics. Flotation rate of post-consumer plastics varies from 0% to 100%. Furthermore, three-category low-energy surface (LES) was defined based on the hydrophile index of the materials involved in this paper, and an adsorption model was proposed to explain the results of flotation and to discuss the floatability of polymer materials modulated by frothers. Frother molecules are prone to adsorb on the surface of bubble rather than LES at relatively low concentration, bubble adsorbed by frother molecules is prone to approach first-category LES rather than third-category LES, and the structure of liquid film is formed on the first-category LES at large concentration. Floatability of polymer materials modulated by frothers is further discussed: frothers increase the floatability of the first-category LES but decrease the floatability of the third-category LES, while the floatability of the second-category LES is related to the type of frothers.     

Rapid discrimination of plastic packaging materials using MIR spectroscopy coupled with independent components analysis (ICA)

Plastic packaging wastes increased considerably in recent decades, raising a major and serious public concern on political, economical and environmental levels. Dealing with this kind of problems is generally done by landfilling and energy recovery. However, these two methods are becoming more and more expensive, hazardous to the public health and the environment. Therefore, recycling is gaining worldwide consideration as a solution to decrease the growing volume of plastic packaging wastes and simultaneously reduce the consumption of oil required to produce virgin resin. Nevertheless, a major shortage is encountered in recycling which is related to the sorting of plastic wastes. In this paper, a feasibility study was performed in order to test the potential of an innovative approach combining mid infrared (MIR) spectroscopy with independent components analysis (ICA), as a simple and fast approach which could achieve high separation rates. This approach (MIR-ICA) gave 100% discrimination rates in the separation of all studied plastics: polyethylene terephthalate (PET), polyethylene (PE), polypropylene (PP), polystyrene (PS) and polylactide (PLA). In addition, some more specific discriminations were obtained separating plastic materials belonging to the same polymer family e.g. high density polyethylene (HDPE) from low density polyethylene (LDPE). High discrimination rates were obtained despite the heterogeneity among samples especially differences in colors, thicknesses and surface textures. The reproducibility of the proposed approach was also tested using two spectrometers with considerable differences in their sensitivities. Discrimination rates were not affected proving that the developed approach could be extrapolated to different spectrometers. MIR combined with ICA is a promising tool for plastic waste separation that can help improve performance in this field; however further technological improvements and developments are required before it can be applied at an industrial level given that all tests presented here were performed under laboratory conditions.     

Separation of packaging plastics by froth flotation in a continuous pilot plant

The objective of the research was to apply froth flotation to separate post-consumer PET (Polyethylene Terephthalate) from other packaging plastics with similar density, in a continuously operated pilot plant. A representative sample composed of 85% PET, 2.5% PVC (Polyvinyl Chloride) and 11.9% PS (Polystyrene) was subjected to a combination of alkaline treatment and surfactant adsorption followed by froth flotation. A mineral processing pilot plant, owned by a Portuguese mining company, was adapted for this purpose. The experimentation showed that it is possible to produce an almost pure concentrate of PET, containing 83% of the PET in feed, in a single bank of mechanical flotation cells. The concentrate grade attained was 97.2% PET, 1.1% PVC and 1.1% PS. By simulation it was shown that the Portuguese recycling industry specifications can be attained if one cleaning and one scavenger stages are added to the circuit.     

Investigation of thermal treatment on selective separation of post consumer plastics prior to froth flotation

Plastics have become the widely used materials because of their advantages, such as cheapness, endurance, lightness, and hygiene. However, they cause waste and soil pollution and they do not easily decompose. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. Depending on their surface characteristics, these plastics can be separated from each other by flotation method which is useful mineral processing technique with its low cost and simplicity.The main objective of this study is to investigate the flotation characteristics of PET and PVC and determine the effect of plasticizer reagents on efficient plastic separation. For that purpose, various parameters such as pH, plasticizer concentration, plasticizer type, conditioning temperature and thermal conditioning were investigated. As a result, PET particles were floated with 95.1% purity and 65.3% efficiency while PVC particles were obtained with 98.1% purity and 65.3% efficiency.     

Cylinder cyclone (LARCODEMS) density media separation of plastic wastes

Cylindrical cyclone media separators using a suspended calcite separation media simulating industrial scale operations are demonstrated to effectively separate a wide variety of forms and a greater range of particle sizes of plastics by density than presently recycled. Purities of plastic products and recoveries obtained from mixed plastic wastes are comparable to those reported for established separations. Products of ≈100% purity with recoveries of >99% were obtained for high density fractions and >98% purities and recoveries for the low density fractions. Cyclonic centrifugal forces and/or the fine particle size of the separation media appear to minimize hydroscopic and particle shape effects.A mathematical model is proposed for defining plastic waste feed rates and treatable particle size ranges for the LARCODEMS media separator.Waste plastic separations yielded Ecart probable (Ep) values ?0.024 for a water only separation media. The Ep for 1.1 g cm^?3 separation medias was <0.032 with minimal to no variation in values for 1–8 mm particle sizes. Variation in the quality of separations is shown to be minimal with <72 μm, <45 μm and <2 μm media particle sizes. Media density offset created varied according to particle size.     

Efficient chemical recycling of waste fiber-reinforced plastics: use of reduced amounts of dimethylaminopyridine and activated charcoal for the purification of recovered monomer

We have achieved major improvements in the efficient chemical recycling of waste fiber-reinforced plastics (FRPs). The effects of reduction in the amounts of dimethylaminopyridine (DMAP) used for depolymerization were examined. The treatment of waste FRP in the presence of 1 or 2 wt% DMAP resulted in the successful recovery of monomeric materials that could be employed in the polymerization process to produce recycled plastic. The separation of linker units from glass fiber, however, was unsuccessful. The purity of the recovered monomeric material, when treated with activated charcoal, was improved to about 70%. This resulted in effective decoloration of the recovered monomer. Finally, the purified material, after undergoing repolymerization, provided high-quality recycled plastic comparable to new plastics produced from new monomers.     

Development of intelligent sorting system realized with the aid of laser-induced breakdown spectroscopy and hybrid preprocessing algorithm-based radial basis function neural networks for recycling black plastic wastes

Plastic recycling has been the key issue for reducing environmental problems and resolving resource depletion. To improve the recovery rate of plastics, the plastic wastes are correctly identified according to their resin type. However, the identification system, which is able to identify black plastics according to not only the type of black plastics but also the grade of resins correctly, has not been introduced. In this paper, laser-induced breakdown spectroscopy, intelligent algorithms and preprocessing algorithms are used to improve the identification of black plastics such as polypropylene, polystyrene (PS), and acrylonitrile butadiene styrene (ABS). The laser-induced breakdown spectroscopy is capable of obtaining the characteristic spectrum regardless of material’s physical state. To extract the new features which are very valuable to improving learning performance, increasing computational efficiency, and building better generalization models from the obtained spectra through laser-induced breakdown spectroscopy, the hybrid preprocessing algorithm, composed of principal component analysis and independent component analysis, is used. In addition, the intelligent algorithm named the extended radial basis function neural networks inheriting the advantages of fuzzy theory and neural networks is used to identify black plastic samples into several categories with respect to their resins. The proposed identification system, composed of three parts such as laser induced breakdown spectroscopy, hybrid preprocessing algorithms, and an efficient intelligent classification algorithm, is able to show the synergy effect on the black plastic identification problem. From several experimental results, it can be seen that the identification system based on laser-induced breakdown spectroscopy and the intelligent algorithm is used for identification of black plastics by resin type.     

Characterization of shredded television scrap and implications for materials recovery

Characterization of TV scrap was carried out by using a variety of methods, such as chemical analysis, particle size and shape analysis, liberation degree analysis, thermogravimetric analysis, sink-float test, and IR spectrometry. A comparison of TV scrap, personal computer scrap, and printed circuit board scrap shows that the content of non-ferrous metals and precious metals in TV scrap is much lower than that in personal computer scrap or printed circuit board scrap. It is expected that recycling of TV scrap will not be cost-effective by utilizing conventional manual disassembly. The result of particle shape analysis indicates that the non-ferrous metal particles in TV scrap formed as a variety of shapes; it is much more heterogeneous than that of plastics and printed circuit boards. Furthermore, the separability of TV scrap using density-based techniques was evaluated by the sink-float test. The result demonstrates that a high recovery of copper could be obtained by using an effective gravity separation process. Identification of plastics shows that the major plastic in TV scrap is high impact polystyrene. Gravity separation of plastics may encounter some challenges in separation of plastics from TV scrap because of specific density variations.     

Thermoplastic vulcanizates from post consumer computer plastics/nitrile rubber blends by dynamic vulcanization

Due to depletion of natural resources and increasing greenhouse emissions, new technologies for the transformation of waste polymers into valuable materials represent one of our greatest current needs. Acrylonitrile–butadiene–styrene terpolymer (ABS) is one of the most widely used engineering plastics and is used as outer casing for electronic equipment. Nitrile rubber (NBR) is used in many applications that demand oil resistance. In an attempt to explore whether these materials can be successfully recycled, we prepared blends of scrap computer plastics (SCP) based on ABS with NBR and waste NBR powder (w-NBR), and investigated their mechanical properties and recyclability. Specifically, we assessed the effect of dynamic vulcanization and replacement of virgin NBR with w-NBR on the properties of 60/40, 70/30, and 80/20 NBR/SCP blends. These blends exhibited thermoplastic elastomeric behavior. The thermoplastic elastomeric blends showed excellent swelling resistance to standard lubricant oil (namely, IRM 903 oil).