Biodegradability and biodegradation rate of poly(caprolactone)-starch blend and poly(butylene succinate) biodegradable polymer under aerobic and anaerobic environment

The biodegradability and the biodegradation rate of two kinds biodegradable polymers; poly(caprolactone) (PCL)-starch blend and poly(butylene succinate) (PBS), were investigated under both aerobic and anaerobic conditions. PCL-starch blend was easily degraded, with 88% biodegradability in 44 days under aerobic conditions, and showed a biodegradation rate of 0.07 day⁻¹, whereas the biodegradability of PBS was only 31% in 80 days under the same conditions, with a biodegradation rate of 0.01 day⁻¹. Anaerobic bacteria degraded well PCL-starch blend (i.e., 83% biodegradability for 139 days); however, its biodegradation rate was relatively slow (6.1 mL CH₄/g-VS day) compared to that of cellulose (13.5 mL CH₄/g-VS day), which was used as a reference material. The PBS was barely degraded under anaerobic conditions, with only 2% biodegradability in 100 days. These results were consistent with the visual changes and FE-SEM images of the two biodegradable polymers after the landfill burial test, showing that only PCL-starch blend had various sized pinholes on the surface due to attack by microorganisms. This result may be use in deciding suitable final disposal approaches of different types of biodegradable polymers in the future.     

Parameters affecting the stability of the digestate from a two-stage anaerobic process treating the organic fraction of municipal solid waste

This paper focused on the factors affecting the respiration rate of the digestate taken from a continuous anaerobic two-stage process treating the organic fraction of municipal solid waste (OFMSW). The process involved a hydrolytic reactor (HR) that produced a leachate fed to a submerged anaerobic membrane bioreactor (SAMBR). It was found that a volatile solids (VS) removal in the range 40-75% and an operating temperature in the HR between 21 and 35 °C resulted in digestates with similar respiration rates, with all digestates requiring 17 days of aeration before satisfying the British Standard Institution stability threshold of 16 mg CO₂ g VS⁻¹ day⁻¹. Sanitization of the digestate at 65 °C for 7 days allowed a mature digestate to be obtained. At 4 g VS L⁻¹ d⁻¹ and Solid Retention Times (SRT) greater than 70 days, all the digestates emitted CO₂ at a rate lower than 25 mg CO₂ g VS⁻¹ d⁻¹ after 3 days of aeration, while at SRT lower than 20 days all the digestates displayed a respiration rate greater than 25 mg CO₂ g VS⁻¹ d⁻¹. The compliance criteria for Class I digestate set by the European Commission (EC) and British Standard Institution (BSI) could not be met because of nickel and chromium contamination, which was probably due to attrition of the stainless steel stirrer in the HR.     

Limits and dynamics of methane oxidation in landfill cover soils

In order to understand the limits and dynamics of methane (CH₄) oxidation in landfill cover soils, we investigated CH₄ oxidation in daily, intermediate, and final cover soils from two California landfills as a function of temperature, soil moisture and CO₂ concentration. The results indicate a significant difference between the observed soil CH₄ oxidation at field sampled conditions compared to optimum conditions achieved through pre-incubation (60 days) in the presence of CH₄ (50 ml l⁻¹) and soil moisture optimization. This pre-incubation period normalized CH₄ oxidation rates to within the same order of magnitude (112-644 μg CH₄ g⁻¹ day⁻¹) for all the cover soils samples examined, as opposed to the four orders of magnitude variation in the soil CH₄ oxidation rates without this pre-incubation (0.9-277 μg CH₄ g⁻¹ day⁻¹).Using pre-incubated soils, a minimum soil moisture potential threshold for CH₄ oxidation activity was estimated at 1500 kPa, which is the soil wilting point. From the laboratory incubations, 50% of the oxidation capacity was inhibited at soil moisture potential drier than 700 kPa and optimum oxidation activity was typical observed at 50 kPa, which is just slightly drier than field capacity (33 kPa). At the extreme temperatures for CH₄ oxidation activity, this minimum moisture potential threshold decreased (300 kPa for temperatures <5 °C and 50 kPa for temperatures >40 °C), indicating the requirement for more easily available soil water. However, oxidation rates at these extreme temperatures were less than 10% of the rate observed at more optimum temperatures (∼30 °C). For temperatures from 5 to 40 °C, the rate of CH₄ oxidation was not limited by moisture potentials between 0 (saturated) and 50 kPa. The use of soil moisture potential normalizes soil variability (e.g. soil texture and organic matter content) with respect to the effect of soil moisture on methanotroph activity. The results of this study indicate that the wilting point is the lower moisture threshold for CH₄ oxidation activity and optimum moisture potential is close to field capacity.No inhibitory effects of elevated CO₂ soil gas concentrations were observed on CH₄ oxidation rates. However, significant differences were observed for diurnal temperature fluctuations compared to thermally equivalent daily isothermal incubations.     

Quantification of multiple methane emission sources at landfills using a double tracer technique

A double tracer technique was used successfully to quantify whole-site methane (CH₄) emissions from Fakse Landfill. Emissions from different sections of the landfill were quantified by using two different tracers. A scaled-down version of the tracer technique measuring close-by to localized sources having limited areal extent was also used to quantify emissions from on-site sources at the landfill facility, including a composting area and a sewage sludge storage pit. Three field campaigns were performed. At all three field campaigns an overall leak search showed that the CH₄ emissions from the old landfill section were localized to the leachate collection wells and slope areas. The average CH₄ emissions from the old landfill section were quantified to be 32.6 ± 7.4 kg CH₄ h⁻¹, whereas the source at the new section was quantified to be 10.3 ± 5.3 kg CH₄ h⁻¹. The CH₄ emission from the compost area was 0.5 ± 0.25 kg CH₄ h⁻¹, whereas the carbon dioxide (CO₂) and nitrous oxide (N₂O) flux was quantified to be in the order of 332 ± 166 kg CO₂ h⁻¹ and 0.06 ± 0.03 kg N₂O h⁻¹, respectively. The sludge pit located west of the compost material was quantified to have an emission of 2.4 ± 0.63 kg h⁻¹ CH₄, and 0.03 ± 0.01 kg h⁻¹ N₂O.     

Effect of aeration modes on the characteristics of composting emissions and the NH3 removal efficiency by using biotrickling filter

A pilot biotrickling filter (BTF) packed with ZX02 fibrous balls as packing material was tested for the treatment of ammonia (NH₃) released from a composting plant of dairy manure. In order to investigate the effects of three compost aeration modes (mode Co-I, Co-II and In-II) on the NH₃ removal efficiency, a field experiment was continuously carried out for more than eight months. The results demonstrated that under the intermittent aeration mode (In-II), the NH₃ removal efficiency reached 99.2 ± 0.1% when the inlet NH₃ concentration was 7.5-32.3 mg m⁻³ (9.8-42.5 ppmv). The maximum and critical elimination capacity of the biotrickling filter was 22.6 and 4.9 g NH₃ m⁻³ h⁻¹, respectively. The effluent concentration of NH₃ was lower than 1.0 mg m⁻³, which meets the first class discharge standards of GB14554-93. When the concentration of free ammonia in the trickling liquid was varied from 0.1 to 0.4 mg L⁻¹, the nitrification yield was between 47.9% and 103.8%. In addition, the optimum liquid tricking velocity (LTV) of the biotrickling filter was 0.5 m³ m⁻² h⁻¹ for low inlet concentrations and 2.2 m³ m⁻² h⁻¹ for high inlet concentrations. Therefore, the use of the biotrickling filter for the compost under the third aeration mode (In-II) yielded an effective optimum NH₃ removal and reduced the nitrogen loss in the compost.     

Photodegradation and Biodegradation Study of a Starch and Poly(Lactic Acid) Coextruded Material

To simulate the behavior of agricultural mulch coextruded poly(lactic acid)(PLA)/starch films, two stages were carried out. The first was an ultraviolet treatment (UV) at 315 nm, during which glass transition temperature T_g, weight, and molecular weight (MW) decreased and a separation between PLA and starch phase was observed. For the second stage, the mineralization of the carbon of the material was followed using the ASTM (D 5209–92 and 5338–92) and ISO/CEN (14852 and 14855) standard procedures. To measure the biodegradability of polymer material, the assessment of the carbon balance allowed determination of the distribution between the carbon rate used to the biomass synthesis or the respiration process (released CO₂), as well as the dissolved organic carbon into the culture medium and the carbon in the residual insoluble material. The influence of the nature of the medium and the standardized procedures on the final rate of biodegradation was investigated. Whatever the standardized method, the biodegradation percentage was significantly stronger in liquid medium (92.4–93.4) than on inert medium (80–83%). In the case of the compost process, only released CO₂ was measured and corresponded to 79.1–80.3%.     

Reducing the environmental impact of methane emissions from dairy farms by anaerobic digestion of cattle waste

Four dairy cattle farms considered representative of Northern Spain milk production were studied. Cattle waste was characterised and energy consumption in the farms was inventoried. Methane emissions due to slurry/manure management and fuel consumption on the farms were calculated. The possibility of applying anaerobic digestion to the slurry to minimise emissions and of using the biogas produced to replace fossil fuels on the farm was considered. Methane emissions due to slurry management (storage and use as fertiliser) ranged from 34 to 66 kg CH₄ cow⁻¹ year⁻¹ for dairy cows and from 13 to 25 kg CH₄ cow⁻¹ year⁻¹ for suckler calves. Cattle on these farms are housed for most of the year, and the contribution from emissions from manure dropped in pastures is insignificant due to the very low methane conversion factors. If anaerobic digestion were implemented on the farms, the potential GHG emissions savings per livestock unit would range from 978 to 1776 kg CO₂ eq year⁻¹, with the main savings due to avoided methane emissions during slurry management. The methane produced would be sufficient to supply digester heating needs (35-55% of the total methane produced) and on-farm fuel energy requirements.     

Temperature Effects on Soil Mineralization of Polylactic Acid Plastic in Laboratory Respirometers

A respirometric system was used to analyze the biodegradation of high molecular weight (120,000 to 200,000 g mol^–1) polylactic acid (PLA) plastic films in soil under laboratory conditions. The respirometric system consisted of air-conditioning pretraps, a soil reactor, and a carbon dioxide (CO₂) posttrap. A 200-g homogeneous soil mixture of all-purpose potting soil : manure soil : sand [1 : 1 : 1 (w/w)] and 1.5 g of PLA plastic films in 1 × 1-cm² squares was added to each bottle. The respirometers were placed in a 28, 40, or 55°C water bath for 182 days. Treatments (three replicates) included native corn starch (positive control), polyethylene (Glad Cling Wrap; negative control), and three PLA films: Ca-I (Cargill Dow Polymers LLC, monolayer), GII (Cargill Dow Polymers LLC, Generation II), and Ch-I (Chronopol; monolayer). The degree of polymer mineralization was indicated by the cumulative CO₂ liberated from each respirometer. The initial average mineralization rate and total percentage mineralized of the PLA plastic films at 28, 40, and 55°C was 24.3, 41.5, and 76.9 mg/day with a 27, 45, and 70% carbon loss, respectively. No decrease in soil pH was observed after 182 days of mineralization. Hence, increase in soil temperature drastically enhanced the biodegradation of PLA plastic films in soil under laboratory conditions (P < 0.0001).     

Treatment of municipal landfill leachate by catalytic wet air oxidation: Assessment of the role of operating parameters by factorial design

The wet air oxidation (WAO) of municipal landfill leachate catalyzed by cupric ions and promoted by hydrogen peroxide was investigated. The effect of operating conditions such as WAO treatment time (15-30 min), temperature (160-200 °C), Cu²⁺ concentration (250-750 mg L⁻¹) and H₂O₂ concentration (0-1500 mg L⁻¹) on chemical oxygen demand (COD) removal was investigated by factorial design considering a two-stage, sequential process comprising the heating-up of the reactor and the actual WAO. The leachate, at an initial COD of 4920 mg L⁻¹, was acidified to pH 3 leading to 31% COD decrease presumably due to the coagulation/precipitation of colloidal and other organic matter. During the 45 min long heating-up period of the WAO reactor under an inert atmosphere, COD removal values up to 35% (based on the initial COD value) were recorded as a result of the catalytic decomposition of H₂O₂ to reactive hydroxyl radicals. WAO at 2.5 MPa oxygen partial pressure advanced treatment further; for example, 22 min of oxidation at 200 °C, 250 mg L⁻¹ Cu²⁺ and 0-1500 mg L⁻¹ H₂O₂ resulted in an overall (i.e. including acidification and heating-up) COD reduction of 78%. Amongst the operating variables in question, temperature had the strongest influence on both the heating-up and WAO stages, while H₂O₂ concentration strongly affected the former and reaction time the latter. Nonetheless, the effects of temperature and H₂O₂ concentration were found to depend on the concentration levels of catalyst as suggested by the significance of their 3rd order interaction term.     

Gasification of the char derived from distillation of granulated scrap tyres

This work reports the effect of pressure on the steam/oxygen gasification at 1000 °C of the char derived from low temperature-pressure distillation of granulated scrap tyres (GST). The study was based on the analysis of gas production, carbon conversion, cold gas efficiency and the high heating value (HHV) of the product. For comparison, similar analyses were carried out for the gasification of coals with different rank.In spite of the relatively high ash (≈12 wt.%) and sulphur (≈3 wt.%) contents, the char produced in GST distillation can be regarded as a reasonable solid fuel with a calorific value of 34 MJ kg⁻¹. The combustion properties of the char (E_A ≈ 50 kJ mol⁻¹), its temperature of self-heating (≈264 °C), ignition temperature (≈459 °C) and burn-out temperature (≈676 °C) were found to be similar to those of a semi-anthracite.It is observed that the yield, H₂ and CO contents and HHV of the syngas produced from char gasification increase with pressure. At 0.1 MPa, 4.6 Nm³ kg_char⁻¹ of syngas was produced, containing 28% v/v of H₂ and CO and with a HHV around 3.7 MJ Nm⁻³. At 1.5 MPa, the syngas yield achieved 4.9 Nm³ kg_char⁻¹ with 30% v/v of H₂-CO and HHV of 4.1 MJ Nm⁻³. Carbon conversion significantly increased from 87% at 0.1 MPa to 98% at 1.5 MPa.It is shown that the char derived from distillation of granulated scrap tyres can be further gasified to render a gas of considerable heating value, especially when gasification proceeds at high pressure.     

Short term effects of copper, sulfadiazine and difloxacin on the anaerobic digestion of pig manure at low organic loading rates

Antibiotics of inorganic and organic origin in pig manure can inhibit the anaerobic process in biogas plants. The influence of three frequently used antibiotics, copper dosed as CuSO₄, sulfadiazine (SDZ), and difloxacin (DIF), on the anaerobic digestion process of pig manure was studied in semi-continuous experiments. Biogas production recovered after every Cu dosage up to a sum of 12.94 g Cu kg⁻¹ organic dry matter (ODM), probably due to Cu precipitation following the formation of sulphide from sulphate. Complete inhibition was found at the very high Cu concentration of 19.40 g Cu kg⁻¹ ODM. Inhibitory effect of SDZ and DIF was observed at concentrations as high as 2.70 g kg⁻¹ ODM and 0.54 g kg⁻¹ ODM, respectively. It seems very unlikely that the antibiotics tested would inhibit the anaerobic process in a full-scale biogas plant.     

Dry-thermophilic anaerobic digestion of organic fraction of municipal solid waste: methane production modeling

The influence of particle size and organic matter content of organic fraction of municipal solid waste (OFMSW) in the overall kinetics of dry (30% total solids) thermophilic (55 °C) anaerobic digestion have been studied in a semi-continuous stirred tank reactor (SSTR). Two types of wastes were used: synthetic OFMSW (average particle size of 1 mm; 0.71 g Volatile Solids/g waste), and OFMSW coming from a composting full scale plant (average particle size of 30 mm; 0.16 g Volatile Solids/g waste).A modification of a widely-validated product-generation kinetic model has been proposed. Results obtained from the modified-model parameterization at steady-state (that include new kinetic parameters as K, Y_pMAX and θ_MIN) indicate that the features of the feedstock strongly influence the kinetics of the process. The overall specific growth rate of microorganisms (μ_max) with synthetic OFMSW is 43% higher compared to OFMSW coming from a composting full scale plant: 0.238 d⁻¹ (K = 1.391 d⁻¹; Y_pMAX = 1.167 L CH₄/gDOC_c; θ_MIN = 7.924 days) vs. 0.135 d⁻¹ (K = 1.282 d⁻¹; Y_pMAX = 1.150 L CH₄/gDOC_c; θ_MIN = 9.997 days) respectively.Finally, it could be emphasized that the validation of proposed modified-model has been performed successfully by means of the simulation of non-steady state data for the different SRTs tested with each waste.     

The effect of bed properties on methane removal in an aerated biofilter--model studies

The capacity of laboratory-scale aerated biofilters to oxidize methane was investigated. Four types of organic and mineral-organic materials were flushed with a mixture of CH₄, CO₂ and air (1:1:8 by volume) during a six-month period. The filter bed materials were as follows: (1) municipal waste compost, (2) an organic horticultural substrate, (3) a composite of expanded perlite and compost amended with zeolite, and (4) the same mixture of perlite and compost amended with bentonite. Methanotrophic capacity during the six months of the experiment reached maximum values of between 889 and 1036 g m⁻² d⁻¹. Batch incubation tests were carried out in order to determine the influence of methane and oxygen concentrations, as well as the addition of sewage sludge, on methanotrophic activity. Michaelis constants K_M for CH₄ and O₂ were 4.6-14.9%, and 0.7-12.3%, respectively. Maximum methanotrophic activities V_max were between 1.3 and 11.6 cm³ g⁻¹ d⁻¹. The activity significantly increased when sewage sludge was added. The main conclusion is that the type of filter bed material (differing significantly in organic matter content, water-holding capacity, or gas diffusion coefficient) was not an important factor in determining methanotrophic capacity when oxygen was supplied to the biofilter.     

Spatial variability of soil gas concentration and methane oxidation capacity in landfill covers

In order to devise design criteria for biocovers intended to enhance the microbial oxidation of landfill methane it is critical to understand the factors influencing gas migration and methane oxidation in landfill cover soils. On an old municipal solid waste landfill in north-western Germany soil gas concentrations (10, 40, 90 cm depth), topsoil methane oxidation capacity and soil properties were surveyed at 40 locations along a 16 m grid. As soil properties determine gas flow patterns it was hypothesized that the variability in soil gas composition and the subsequent methanotrophic activity would correspond to the variability of soil properties. Methanotrophic activity was found to be subject to high spatial variability, with values ranging between 0.17 and 9.80 g CH₄ m⁻² h⁻¹_. Considering the current gas production rate of 0.03 g CH₄ m⁻² h⁻¹, the oxidation capacity at all sampled locations clearly exceeded the flux to the cover, and can be regarded as an effective instrument for mitigating methane fluxes. The methane concentration in the cover showed a high spatial heterogeneity with values between 0.01 and 0.32 vol.% (10 cm depth), 22.52 vol.% (40 cm), and 36.85 vol.% (90 cm). The exposure to methane raised the oxidation capacity, suggested by a statistical correlation to an increase in methane concentration at 90 cm depth. Methane oxidation capacity was further affected by the methanotroph bacteria pH optimum and nutrient availability, and increased with decreasing pH towards neutrality, and increased with soluble ion concentration). Soil methane and carbon dioxide concentration increased with lower flow resistance of the cover, as represented by the soil properties of a reduced bulk density, increase in air capacity and in relative ground level.     

Evaluation of respiration in compost landfill biocovers intended for methane oxidation

A low-cost alternative approach to reduce landfill gas (LFG) emissions is to integrate compost into the landfill cover design in order to establish a biocover that is optimized for biological oxidation of methane (CH₄). A laboratory and field investigation was performed to quantify respiration in an experimental compost biocover in terms of oxygen (O₂) consumption and carbon dioxide (CO₂) production and emission rates. O₂ consumption and CO₂ production rates were measured in batch and column experiments containing compost sampled from a landfill biowindow at Fakse landfill in Denmark. Column gas concentration profiles were compared to field measurements. Column studies simulating compost respiration in the biowindow showed average CO₂ production and O₂ consumption rates of 107 ± 14 g m⁻² d⁻¹ and 63 ± 12 g m⁻² d⁻¹, respectively. Gas profiles from the columns showed elevated CO₂ concentrations throughout the compost layer, and CO₂ concentrations exceeded 20% at a depth of 40 cm below the surface of the biowindow. Overall, the results showed that respiration of compost material placed in biowindows might generate significant CO₂ emissions. In landfill compost covers, methanotrophs carrying out CH₄ oxidation will compete for O₂ with other aerobic microorganisms. If the compost is not mature, a significant portion of the O₂ diffusing into the compost layer will be consumed by non-methanotrophs, thereby limiting CH₄ oxidation. The results of this study however also suggest that the consumption of O₂ in the compost due to aerobic respiration might increase over time as a result of the accumulation of biomass in the compost after prolonged exposure to CH₄.     

Enhanced Mineralization of PLA Meltblown Materials Due to Plasticization

Polylactic acid (PLA) is one of the important biodegradable polymers. It is widely used in many industrial applications such as films and fibers. Its biodegradability is based on data derived mostly from composting processes. For a broad application of the PLA material in personal care products, an understanding of anaerobic biodegradability is essential because soiled personal care products are usually disposed of in sanitary landfills, where biodegradability mechanisms are predominately in anaerobic conditions. Extensive laboratory results are acquired to elucidate the effects of the temperature on the PLA anaerobic sludge biodegradation. When the temperature is higher than PLA glass transition temperature (T_g), anaerobic degradation is accelerated. A plausible mechanism to explain this observation is that amorphous part of the polymer is easily accessible by microorganisms. When the degrading temperature is below PLA glass transition temperature, sample mineralization under anaerobic conditions is apparently slowed. The mechanisms elucidated by T_g modification can be utilized to control the rate of PLA biodegradation for sustainable waste management.     

Fate and distribution of nitrogen in soil and plants irrigated with landfill leachate

Landfill leachate contains a high concentration of ammoniacal substances which can be a potential supply of N for plants. A bioassay was conducted using seeds of Brassica chinensis and Lolium perenne to evaluate the phytotoxicity of the leachate sample. A soil column experiment was then carried out in a greenhouse to study the effect of leachate on plant growth. Two grasses (Paspalum notatum and Vetiver zizanioides) and two trees (Hibiscus tiliaceus and Litsea glutinosa) were irrigated with leachate at the EC50 levels for 12 weeks. Their growth performance and the distribution of N were examined and compared with columns applied with chemical fertilizer. With the exception of P. notatum, plants receiving leachate and fertilizer grew better than those receiving water alone. The growth of L. glutinosa and V. zizanioides with leachate irrigation did not differ significantly from plants treated with fertilizer. Leachate irrigation significantly increased the levels of NH_x-N in soil. Although NO_x-N was below 1 mg N L⁻¹ in the leachate sample, the soil NO_x-N content increased by 9-fold after leachate irrigation, possibly as a result of nitrification. Leachate irrigation at EC50 provided an N input of 1920 kg N ha⁻¹ over the experimental period, during which up to 1050 kg N ha⁻¹ was retained in the soil and biomass, depending on the type of vegetation. The amount of nutrient added seems to exceed beyond the assimilative capability. Practitioners should be aware of the possible consequence of N saturation when deciding the application rate if leachate irrigation is aimed for water reuse.     

Environmental assessment of garden waste management in the Municipality of Aarhus, Denmark

An environmental assessment of six scenarios for handling of garden waste in the Municipality of Aarhus (Denmark) was performed from a life cycle perspective by means of the LCA-model EASEWASTE. In the first (baseline) scenario, the current garden waste management system based on windrow composting was assessed, while in the other five scenarios alternative solutions including incineration and home composting of fractions of the garden waste were evaluated. The environmental profile (normalised to Person Equivalent, PE) of the current garden waste management in Aarhus is in the order of −6 to 8 mPE Mg⁻¹ ww for the non-toxic categories and up to 100 mPE Mg⁻¹ ww for the toxic categories. The potential impacts on non-toxic categories are much smaller than what is found for other fractions of municipal solid waste. Incineration (up to 35% of the garden waste) and home composting (up to 18% of the garden waste) seem from an environmental point of view suitable for diverting waste away from the composting facility in order to increase its capacity. In particular the incineration of woody parts of the garden waste improved the environmental profile of the garden waste management significantly.     

Influence of aeration on CH4, N2O and NH3 emissions during aerobic composting of a chicken manure and high C/N waste mixture

Co-composting of chicken manure, straw and dry grasses was investigated in a forced aeration system to estimate the effect of aeration rates on NH₃, CH₄ and N₂O emissions and compost quality. Continuous measurements of gas emissions were carried out and detailed gas emission patterns were obtained using an intermittent-aeration of 30 min on/30 min off at rates of 0.01 (A1), 0.1 (A2) and 0.2 (A3) m³ min⁻¹ m⁻³. Concentrations of CH₄ and N₂O at the low aeration rate (A1) were significantly greater than those at the other two rates, but there was no significant difference between the A2 and A3 treatments. CH₄ and N₂O emissions for this mixture could be controlled when the composting process was aerobic and ammonia emissions were reduced at a lower aeration rate. Comparison of CH₄, N₂O, NH₃ emissions and compost quality showed that the aeration rate of the A2 treatment was superior to the other two aeration rates.     

Determination of first-order landfill gas modeling parameters and uncertainties

Using first-order kinetic empirical models to estimate landfill gas (LFG) generation and collection rates is well recognized in the literature. The uncertainty in the estimated LFG generation rates is a major challenge in evaluating performance of LFG collection and LFG to energy facilities. In this investigation, four methods for quantifying first-order LFG generation model parameters, methane generation potential, L₀, and methane generation rate constant, k, were evaluated. It was found that the model is insensitive to the approach taken in quantifying the parameters. However, considering the recognition of using the model in the literature, the optimum method to estimate L₀ and k is to determine L₀ using disposed municipal solid waste composition and laboratory component specific methane potential values. The k value can be selected by model fitting and regression using the first-order model if LFG collection data are available. When such data are not available, k can be selected from technical literature, based on site conditions. For five Florida case-study landfills L₀ varied from 56 to 77 m³ Mg⁻¹, and k varied from 0.04 to 0.13 yr⁻¹ for the traditional landfills and was 0.10 yr⁻¹ for the wet cell. Model predictions of LFG collection rates were on average lower than actual collection. The uncertainty (coefficient of variation) in modeled LFG generation rates varied from ±11% to ±17% while landfills were open, ±9% to ±18% at the end of waste placement, and ±16% to ±203% 50 years after waste placement ended.