Passive drainage and biofiltration of landfill gas: Australian field trial

In Australia a significant number of landfill waste disposal sites do not incorporate measures for the collection and treatment of landfill gas. This includes many old/former landfill sites, rural landfill sites, non-putrescible solid waste and inert waste landfill sites, where landfill gas generation is low and it is not commercially viable to extract and beneficially utilize the landfill gas. Previous research has demonstrated that biofiltration has the potential to degrade methane in landfill gas, however, the microbial processes can be affected by many local conditions and factors including moisture content, temperature, nutrient supply, including the availability of oxygen and methane, and the movement of gas (oxygen and methane) to/from the micro-organisms. A field scale trial is being undertaken at a landfill site in Sydney, Australia, to investigate passive drainage and biofiltration of landfill gas as a means of managing landfill gas emissions at low to moderate gas generation landfill sites. The design and construction of the trial is described and the experimental results will provide in-depth knowledge on the application of passive gas drainage and landfill gas biofiltration under Sydney (Australian) conditions, including the performance of recycled materials for the management of landfill gas emissions.     

Passive landfill gas emission - Influence of atmospheric pressure and implications for the operation of methane-oxidising biofilters

A passively vented landfill site in Northern Germany was monitored for gas emission dynamics through high resolution measurements of landfill gas pressure, flow rate and composition as well as atmospheric pressure and temperature. Landfill gas emission could be directly related to atmospheric pressure changes on all scales as induced by the autooscillation of air, diurnal variations and the passage of pressure highs and lows. Gas flux reversed every 20 h on average, with 50% of emission phases lasting only 10h or less. During gas emission phases, methane loads fed to a connected methane oxidising biofiltration unit varied between near zero and 247 g CH4 h(-1)m(-3) filter material. Emission dynamics not only influenced the amount of methane fed to the biofilter but also the establishment of gas composition profiles within the biofilter, thus being of high relevance for biofilter operation. The duration of the gas emission phase emerged as most significant variable for the distribution of landfill gas components within the biofilter.     

Performance of a passively vented field-scale biofilter for the microbial oxidation of landfill methane

An upflow biofilter system was operated on a passively vented landfill for the treatment of residual landfill methane. Biofilter methane emissions as a basis for determining methane removal rates were assessed by manual and automated chamber measurements, by measuring methane concentrations in the top layer gaseous phase in combination with gas flow rates, and by evaluating the methane load in the reverse gas flow following the change of landfill gas flux direction as governed by the course of barometric pressure. Methane removal rates were very high with maximum values of 80 g h(-1) m(-3). For the observed cases, the limit of biofilter methane oxidation capacity was not reached and absolute removal rates were thus linearly correlated to the amount of methane entering the filter. The analysis of methane loads flowing back from the biofilter following phases of longer, continuous and non-oscillating landfill gas emission, however, revealed that in these situations biofilter performance is restricted by deficient oxygen supply. At the oxygen-restricted capacity limit, removal rates are influenced by temperature (positively), methane influx (negatively) and flow rate (negatively) as a measure for the displacement of oxygen. These situations, however, account for only 12% of all emission phases. The investigated biofilter capacity, as derived from laboratory analyses of methanotrophic activities, is sufficient to oxidise 62% of the methane load emitted annually. Field and laboratory data provide a stable basis for the dimensioning of filters in future applications.     

Methane oxidation in water-spreading and compost biofilters.

This study evaluated two biofilter designs to mitigate methane emissions from landfill vents. Water-spreading biofilters were designed to use the capillarity of coarse sand overlain by a finer sand to increase the active depth for methane oxidation. Compost biofilters consisted of 238-L barrels containing a 1:1 mixture (by volume) of compost to expanded polystyrene pellets. Two replicates of each type of biofilter were tested at an outdoor facility. Gas inflow consisted of an approximately 1:1 mixture (by volume) of CH4 and CO2. Methane output rates (J(out); g m(-2) day(-1)) were measured using the static chamber technique and the Pedersen et al. (2001) diffusion model. Methane oxidation rate (J(ox); g m(-2) day(-1)) and fraction of methane oxidized (f(ox)) were determined by mass balance. For methane inflow rates (J(in)) between 250 and 500 g m(-2) day(-1), the compost biofilter J(ox), 242 g m(-2) day(-1), was not significantly different (P = 0.0647) than the water-spreading biofilter J(ox), 203 g m(-2) day(-1); and the compost f(ox), 69%, was not significantly different (P = 0.7354) than water-spreading f(ox), 63%. The water-spreading biofilter was shown to generally perform as well as the compost biofilter, and it may be easier to implement at a landfill and require less maintenance.     

Microbial oxidation of methane from old landfills in biofilters

Landfill gas emissions are among the largest sources of the greenhouse gas methane. For this reason, the possibilities of microbial methane degradation in biofilters were investigated. Different filter materials were tested in two experimental plants, a bench-scale plant (total filter volume 51 l) and a pilot plant (total filter volume 4 m3). Three months after the beginning of the experiment, very high degradation rates of up to 63 g CH4/(m3h) were observed in the bench-scale plant at mean methane concentrations of 2.5% v/v and with fine-grained compost as biofilter material. However, the degradation rates of the compost biofilter decreased in the fifth month of the experiment, probably due to the accumulation of exopolymeric substances formed by the microorganisms. A mixture of compost, peat, and wood fibers showed stable and satisfactory degradation rates around 20 g/(m3h) at mean concentrations of 3% v/v over a period of one year. In this material, the wood fibers served as a structural material and prevented clogging of the biofilter. Extrapolation of the experimental data indicates that biofilters for methane oxidation have to be at least 100 times the volume of biofilters for odor control to obtain the same cleaning efficiency per unit volume flow of feed gas.     

Biotic systems to mitigate landfill methane emissions.

Landfill gases produced during biological degradation of buried organic wastes include methane, which when released to the atmosphere, can contribute to global climate change. Increasing use of gas collection systems has reduced the risk of escaping methane emissions entering the atmosphere, but gas capture is not 100% efficient, and further, there are still many instances when gas collection systems are not used. Biotic methane mitigation systems exploit the propensity of some naturally occurring bacteria to oxidize methane. By providing optimum conditions for microbial habitation and efficiently routing landfill gases to where they are cultivated, a number of bio-based systems, such as interim or long-term biocovers, passively or actively vented biofilters, biowindows and daily-used biotarps, have been developed that can alone, or with gas collection, mitigate landfill methane emissions. This paper reviews the science that guides bio-based designs; summarizes experiences with the diverse natural or engineered substrates used in such systems; describes some of the studies and field trials being used to evaluate them; and discusses how they can be used for better landfill operation, capping, and aftercare.     

Performance of Trickle-Bed Air Biofilter: A Comparative Study of a Hydrophilic and a Hydrophobic Voc

Two lab-scale trickle-bed air biofilters were operated for investigating the difference in performance between a hydrophilic and a hydrophobic volatile organic compound (VOC). Methyl isobutyl ketone (MIBK) and styrene were selected as a model hydrophilic and hydrophobic VOCs, respectively. Effects of loading rates, biofilter re-acclimation, removal profile along biofilter depth, nitrogen consumption, and CO₂ production were compared under three operating conditions, namely, backwashing and two non-use periods (starvation and stagnant). Consistent over 99% removal efficiency up to loading rates of 3.26 kg COD/m³-day was obtained for the MIBK biofilter at 0.76 min empty bed retention time (EBRT) and 1.5 L/d nutrient flow. A similar performance for the styrene biofilter was obtained for loading rates up to 1.9kg COD/m³-day at 2.02 min EBRT and 2.4 L/d nutrient flow. The MIBK biofilter required only an initial acclimation period of 16 days while styrene biofilter required 46 days. Non-use periods can be used as another means of biomass control for both biofilters when the employed loading rate did not exceed 1.27 and 2.17 kg COD/m³-day for styrene and MIBK biofilters, respectively. The re-acclimation of both biofilter was delayed with increase of loading rate. MIBK biofilter re-acclimated in 90 min, while styrene biofilter re-acclimated in more than 600 min. Under similar loading rates, MIBK biofilter utilized less biofilter depth than styrene biofilter. Nitrogen consumption behaviors were apparently different between the two biofilters. Styrene biofilter had higher CO₂ production than MIBK biofilter and its CO₂ production was closely related to the theoretical complete chemical oxidation.     

Assessment of the methane oxidation capacity of compacted soils intended for use as landfill cover materials

The microbial oxidation of methane in engineered cover soils is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes of low methane generation rates. A laboratory column study was conducted in order to derive design criteria that enable construction of an effective methane oxidising cover from the range of soils that are available to the landfill operator. Therefore, the methane oxidation capacity of different soils was assessed under simulated landfill conditions. Five sandy potential landfill top cover materials with varying contents of silt and clay were investigated with respect to methane oxidation and corresponding soil gas composition over a period of four months. The soils were compacted to 95% of their specific proctor density, resulting in bulk densities of 1.4-1.7 g cm⁻³, reflecting considerably unfavourable conditions for methane oxidation due to reduced air-filled porosity. The soil water content was adjusted to field capacity, resulting in water contents ranging from 16.2 to 48.5 vol.%. The investigated inlet fluxes ranged from 25 to about 100 g CH₄ m⁻² d⁻¹, covering the methane load proposed to allow for complete oxidation in landfill covers under Western European climate conditions and hence being suggested as a criterion for release from aftercare. The vertical distribution of gas concentrations, methane flux balances as well as stable carbon isotope studies allowed for clear process identifications. Higher inlet fluxes led to a reduction of the aerated zone, an increase in the absolute methane oxidation rate and a decline of the relative proportion of oxidized methane. For each material, a specific maximum oxidation rate was determined, which varied between 20 and 95 g CH₄ m⁻² d⁻¹ and which was positively correlated to the air-filled porosity of the soil. Methane oxidation efficiencies and gas profile data imply a strong link between oxidation capacity and diffusive ingress of atmospheric air. For one material with elevated levels of fine particles and high organic matter content, methane production impeded the quantification of methane oxidation potentials. Regarding the design of landfill cover layers it was concluded that the magnitude of the expected methane load, the texture and expected compaction of the cover material are key variables that need to be known. Based on these, a column study can serve as an appropriate testing system to determine the methane oxidation capacity of a soil intended as landfill cover material.     

Performance evaluation of an anaerobic/aerobic landfill-based digester using yard waste for energy and compost production

The objective of this study was to evaluate a new alternative for yard waste management by constructing, operating and monitoring a landfill-based two-stage batch digester (anaerobic/aerobic) with the recovery of energy and compost. The system was initially operated under anaerobic conditions for 366 days, after which the yard waste was aerated for an additional 191 days. Off gas generated from the aerobic stage was treated by biofilters. Net energy recovery was 84.3MWh, or 46kWh per million metric tons of wet waste (as received), and the biochemical methane potential of the treated waste decreased by 83% during the two-stage operation. The average removal efficiencies of volatile organic compounds and non-methane organic compounds in the biofilters were 96-99% and 68-99%, respectively.     

Kinetics of microbial landfill methane oxidation in biofilters

A methane oxidizing biofilter system fitted to the passive venting system of a harbor sludge landfill in Germany was characterized with respect to the the methanotrophic population, methane oxidizing capacity, and reaction kinetics. Methanotrophic cell counts stabilized on a high level with 1.3 x 10(8) to 7.1 x 10(9) cells g dw(-1) about one year after first biofilter operation, and a maximum of 1.2 x 10(11) cells g dw(-1). Potential methane oxidizing activity varied between 5.3 and 10.7 microg h(-1) g dw(-1). Cell numbers correlated well with methane oxidation activities. Extrapolation of potential activities gave methane removal rates between 35 and 109 g CH4 h(-1) m(-3), calculated for 30 degrees C. Optimum temperature was 38 degrees C for freshly sampled biofilter material and 22 degrees C for a methanotrophic enrichment culture grown at 10 degrees C incubation temperature. Substrate kinetics revealed the presence of a low-affinity methane oxidizing community with a high Vmax of 1.78 micromol CH4 h(-1) g ww(-1) and a high K(M) of 15.1 microM. K(MO2) for methane oxidation was 58 microM. No substantial methane oxidizing activity was detected below 1.7-2.6 vol.-% O2 in the gaseous phase. Methane deprivation led to a decrease in methane oxidation activity within 5-9 weeks but could still be detected after 25 weeks of substrate deprivation and was fully restored within 3 weeks of continuous methane supply. Very high salt loads are leached from the novel biofilter material, expanded clay, yielding electric conductivity values of up to 15 mS cm(-1) in the leachate. Values > 6 mS cm(-1) were shown to depress methane consumption. Water retention characteristics of the material proved to be favourable for methane oxidizing systems with a gas permeable volume of 78% of bulk volume at field capacity water content. Correspondingly, no influence of water content on methane oxidation activity could be detected at water contents between 2.5 and 20 vol.-%.     

Bio-tarp alternative daily cover prototypes for methane oxidation atop open landfill cells

Final landfill covers are highly engineered to prevent methane release into the atmosphere. However, methane production begins soon after waste placement and is an unaddressed source of emissions. The methane oxidation capacity of methanotrophs embedded in a “bio-tarp” was investigated as a means to mitigate methane release from open landfill cells. The bio-tarp would also serve as an alternative daily cover during routine landfill operation.Evaluations of nine synthetic geotextiles identified two that would likely be suitable bio-tarp components. Pilot tarp prototypes were tested in continuous flow systems simulating landfill gas conditions. Multilayered bio-tarp prototypes consisting of alternating layers of the two geotextiles were found to remove 16% of the methane flowing through the bio-tarp. The addition of landfill cover soil, compost, or shale amendments to the bio-tarp increased the methane removal up to 32%. With evidence of methane removal in a laboratory bioreactor, prototypes were evaluated at a local landfill using flux chambers installed atop intermediate cover at a landfill. The multilayered bio-tarp and amended bio-tarp configurations were all found to decrease landfill methane flux; however, the performance efficacy of bio-tarps was not significantly different from controls without methanotrophs. Because highly variable methane fluxes at the field site likely confounded the test results, repeat field testing is recommended under more controlled flux conditions.     

Modelling of stable isotope fractionation by methane oxidation and diffusion in landfill cover soils

A technique to measure biological methane oxidation in landfill cover soils that is gaining increased interest is the measurement of stable isotope fractionation in the methane. Usually to quantify methane oxidation, only fractionation by oxidation is taken into account. Recently it was shown that neglecting the isotope fractionation by diffusion results in underestimation of the methane oxidation. In this study a simulation model was developed that describes gas transport and methane oxidation in landfill cover soils. The model distinguishes between (12)CH(4), (13)CH(4), and (12)CH(3)D explicitly, and includes isotope fractionation by diffusion and oxidation. To evaluate the model, the simulations were compared with column experiments from previous studies. The predicted concentration profiles and isotopic profiles match the measured ones very well, with a root mean square deviation (RMSD) of 1.7vol% in the concentration and a RMSD of 0.8 per thousand in the delta(13)C value, with delta(13)C the relative (13)C abundance as compared to an international standard. Overall, the comparison shows that a model-based isotope approach for the determination of methane oxidation efficiencies is feasible and superior to existing isotope methods.     

Temporal variability of soil gas composition in landfill covers

In order to assess the temporal variability of the conditions for the microbial oxidation of methane in landfill cover soils and their driving variables, gas composition at non-emissive and strongly emissive locations (hotspots) was monitored on a seasonal, daily and hourly time scale on an old, unlined landfill in northern Germany. Our study showed that the impact of the various environmental factors varied with the mode of gas transport and with the time scale considered. At non-emissive sites, governed by diffusive gas transport, soil gas composition was subject to a pronounced seasonal variation. A high extent of aeration, low methane concentrations and a high ratio of CO₂ to CH₄ were found across the entire depth of the soil cover during the warm and dry period, whereas in the cool and moist period aeration was less and landfill gas migrated further upward. Statistically, variation in soil gas composition was best explained by the variation in soil temperature. At locations dominated by advective gas transport and showing considerable emissions of methane, this pattern was far less pronounced with only little increase in the extent of aeration during drier periods. Here, the change of barometric pressure was found to impact soil gas composition. On a daily scale under constant conditions of temperature, gas transport at both types of locations was strongly impacted by the change in soil moisture. On an hourly scale, under constant conditions of temperature and moisture, gas migration was impacted most by the change in barometric pressure. It was shown that at diffusion-dominated sites complete methane oxidation was achieved even under adverse wintry conditions, whereas at hotspots, even under favorable dry and warm conditions, aerobic biological activity can be limited to the upper crust of the soil.     

Odour control at biowaste composting facilities

There are several options to effectively reduce odorous emissions at composting facilities depending on the type of composting system used. Some of the more relevant measures for open and enclosed composting facilities are presented in this article. Results from different investigations on odour reduction efficiencies of biological waste gas treatment systems at various scales are presented. Biofilter/bioscrubber combinations were used and different biofilter materials were tested. The more relevant odorous substances in the waste gas were identified, and their reduction in the different systems was measured. The biofilter proved to be mainly responsible for efficient odour degradation. The investigations presented in this article revealed that screened compost was very effective, and proved to be a low cost biofilter material for odour degradation purposes. Screened compost showed higher degradation rates than a coke-compost mixture newly developed by the University of Leipzig. Furthermore, it seems that enclosed systems have advantages when compared to conventional open single bed biofilters.     

Generating CO2-credits through landfill in situ aeration

Landfills are some of the major anthropogenic sources of methane emissions worldwide. The installation and operation of gas extraction systems for many landfills in Europe and the US, often including technical installations for energy recovery, significantly reduced these emissions during the last decades. Residual landfill gas, however, is still continuously produced after the energy recovery became economically unattractive, thus resulting in ongoing methane emissions for many years. By landfill in situ aeration these methane emissions can be widely avoided both, during the aeration process as well as in the subsequent aftercare period. Based on model calculations and online monitoring data the amount of avoided CO_2-eq. can be determined. For an in situ aerated landfill in northern Germany, acting as a case study, 83–95% (depending on the kind and quality of top cover) of the greenhouse gas emission potential could be reduced under strictly controlled conditions. Recently the United Nations Framework Convention on Climate Change (UNFCCC) has approved a new methodology on the “Avoidance of landfill gas emissions by in situ aeration of landfills” (UNFCCC, 2009). Based on this methodology landfill aeration projects might be considered for generation of Certified Emission Reductions (CERs) in the course of CDM projects. This paper contributes towards an evaluation of the potential of landfill aeration for methane emissions reduction.     

Improved methodology to assess modification and completion of landfill gas management in the aftercare period

Municipal solid waste landfills represent the dominant option for waste disposal in many parts of the world. While some countries have greatly reduced their reliance on landfills, there remain thousands of landfills that require aftercare. The development of cost-effective strategies for landfill aftercare is in society’s interest to protect human health and the environment and to prevent the emergence of landfills with exhausted aftercare funding. The Evaluation of Post-Closure Care (EPCC) methodology is a performance-based approach in which landfill performance is assessed in four modules including leachate, gas, groundwater, and final cover. In the methodology, the objective is to evaluate landfill performance to determine when aftercare monitoring and maintenance can be reduced or possibly eliminated. This study presents an improved gas module for the methodology. While the original version of the module focused narrowly on regulatory requirements for control of methane migration, the improved gas module also considers best available control technology for landfill gas in terms of greenhouse gas emissions, air quality, and emissions of odoriferous compounds. The improved module emphasizes the reduction or elimination of fugitive methane by considering the methane oxidation capacity of the cover system. The module also allows for the installation of biologically active covers or other features designed to enhance methane oxidation. A methane emissions model, CALMIM, was used to assist with an assessment of the methane oxidation capacity of landfill covers.     

CHANGES IN MAJOR AND TRACE COMPONENTS OF LANDFILL GAS DURING SUBSURFACE MIGRATION

A gas plume emanating from the Foxhall Landfill in Suffolk (U.K.) has been defined within unsaturated ferruginous sands on the basis of elevated concentrations of methane, carbon dioxide and volatile organic compounds (VOCs). The plume is relatively narrow, extends more than 100 m from the landfill boundary, and lies mainly between 2 m bgl (below ground level) and the water table at 9.5 m bgl. With increasing distance along the axis of the plume, the ratio of methane to carbon dioxide gradually decreases, while nitrogen increases. Oxygen appears beyond 80 m from the landfill boundary. Stable carbon and hydrogen isotope ratios in methane become heavier with distance, while carbon dioxide becomes isotopically lighter with respect to stable carbon. This provides strong evidence for microbially mediated methane oxidation. Zones of black reduced sediment near the landfill suggest that ferric iron [Fe(III)] may be acting as an electron acceptor for oxidation. No thermal anomaly was observed, thus suggesting that the rate of oxidation/flux of methane is low. Volatile organic compounds in the plume were trapped using a combination of sorbants (Tenax GR, Haysep Q and Carbosieve S-III), and desorbed thermally into a GC/MS for semi-quantitative analysis. The 79 VOCs identified were similar to those found in other landfills, and their concentrations, both in the landfill and in the soil gas, were broadly related to their volatility. Only two compounds (vinyl chloride and dichlorofluoromethane) approached or exceeded the long-term exposure limit (LTEL, as defined by the U.K. Health and Safety Executive, 1992) outside the landfill. Halogenated compounds (dichlorodifluoromethane, dichlorofluoromethane and trichlorofluoromethane) were found to be most mobile but their concentration profiles suggest that they may have been flushed out of the landfill during its early stages. It is suggested that the association of volatile halogenated compounds with methane is good evidence that they are derived from a landfill.     

Impact of different plants on the gas profile of a landfill cover

Methane is an important greenhouse gas emitted from landfill sites and old waste dumps. Biological methane oxidation in landfill covers can help to reduce methane emissions. To determine the influence of different plant covers on this oxidation in a compost layer, we conducted a lysimeter study. We compared the effect of four different plant covers (grass, alfalfa + grass, miscanthus and black poplar) and of bare soil on the concentration of methane, carbon dioxide and oxygen in lysimeters filled with compost. Plants were essential for a sustainable reduction in methane concentrations, whereas in bare soil, methane oxidation declined already after 6 weeks. Enhanced microbial activity - expected in lysimeters with plants that were exposed to landfill gas - was supported by the increased temperature of the gas in the substrate and the higher methane oxidation potential. At the end of the first experimental year and from mid-April of the second experimental year, the methane concentration was most strongly reduced in the lysimeters containing alfalfa + grass, followed by poplar, miscanthus and grass. The observed differences probably reflect the different root morphology of the investigated plants, which influences oxygen transport to deeper compost layers and regulates the water content.     

Scaling methane oxidation: from laboratory incubation experiments to landfill cover field conditions

Evaluating field-scale methane oxidation in landfill cover soils using numerical models is gaining interest in the solid waste industry as research has made it clear that methane oxidation in the field is a complex function of climatic conditions, soil type, cover design, and incoming flux of landfill gas from the waste mass. Numerical models can account for these parameters as they change with time and space under field conditions. In this study, we developed temperature, and water content correction factors for methane oxidation parameters. We also introduced a possible correction to account for the different soil structure under field conditions. These parameters were defined in laboratory incubation experiments performed on homogenized soil specimens and were used to predict the actual methane oxidation rates to be expected under field conditions. Water content and temperature corrections factors were obtained for the methane oxidation rate parameter to be used when modeling methane oxidation in the field. To predict in situ measured rates of methane with the model it was necessary to set the half saturation constant of methane and oxygen, K_m, to 5%, approximately five times larger than laboratory measured values. We hypothesize that this discrepancy reflects differences in soil structure between homogenized soil conditions in the lab and actual aggregated soil structure in the field. When all of these correction factors were re-introduced into the oxidation module of our model, it was able to reproduce surface emissions (as measured by static flux chambers) and percent oxidation (as measured by stable isotope techniques) within the range measured in the field.