Evaluation of respiration in compost landfill biocovers intended for methane oxidation

A low-cost alternative approach to reduce landfill gas (LFG) emissions is to integrate compost into the landfill cover design in order to establish a biocover that is optimized for biological oxidation of methane (CH₄). A laboratory and field investigation was performed to quantify respiration in an experimental compost biocover in terms of oxygen (O₂) consumption and carbon dioxide (CO₂) production and emission rates. O₂ consumption and CO₂ production rates were measured in batch and column experiments containing compost sampled from a landfill biowindow at Fakse landfill in Denmark. Column gas concentration profiles were compared to field measurements. Column studies simulating compost respiration in the biowindow showed average CO₂ production and O₂ consumption rates of 107 ± 14 g m⁻² d⁻¹ and 63 ± 12 g m⁻² d⁻¹, respectively. Gas profiles from the columns showed elevated CO₂ concentrations throughout the compost layer, and CO₂ concentrations exceeded 20% at a depth of 40 cm below the surface of the biowindow. Overall, the results showed that respiration of compost material placed in biowindows might generate significant CO₂ emissions. In landfill compost covers, methanotrophs carrying out CH₄ oxidation will compete for O₂ with other aerobic microorganisms. If the compost is not mature, a significant portion of the O₂ diffusing into the compost layer will be consumed by non-methanotrophs, thereby limiting CH₄ oxidation. The results of this study however also suggest that the consumption of O₂ in the compost due to aerobic respiration might increase over time as a result of the accumulation of biomass in the compost after prolonged exposure to CH₄.     

Effects of compost biocovers on gas flow and methane oxidation in a landfill cover

Previous publications described the performance of biocovers constructed with a compost layer placed on select areas of a landfill surface characterized by high emissions from March 2004 to April 2005. The biocovers reduced CH₄ emissions 10-fold by hydration of underlying clay soils, thus reducing the overall amount of CH₄ entering them from below, and by oxidation of a greater portion of that CH₄. This paper examines in detail the field observations made on a control cell and a biocover cell from January 1, 2005 to December 31, 2005. Field observations were coupled to a numerical model to contrast the transport and attenuation of CH₄ emissions from these two cells. The model partitioned the biocover’s attenuation of CH₄ emission into blockage of landfill gas flow from the underlying waste and from biological oxidation of CH₄. Model inputs were daily water content and temperature collected at different depths using thermocouples and calibrated TDR probes. Simulations of CH₄ transport through the two soil columns depicted lower CH₄ emissions from the biocover relative to the control. Simulated CH₄ emissions averaged 0.0 g m^?2 d^?1 in the biocover and 10.25 g m^?2 d^?1 in the control, while measured values averaged 0.04 g m^?2 d^?1 in the biocover and 14 g m^?2 d^?1 in the control. The simulated influx of CH₄ into the biocover (2.7 g m^?2 d^?1) was lower than the simulated value passing into the control cell (29.4 g m^?2 d^?1), confirming that lower emissions from the biocover were caused by blockage of the gas stream. The simulated average rate of biological oxidation predicted by the model was 19.2 g m^?2 d^?1 for the control cell as compared to 2.7 g m^?2 d^?1 biocover. Even though its V_max was significantly greater, the biocover oxidized less CH₄ than the control cell because less CH₄ was supplied to it.     

Observations on the methane oxidation capacity of landfill soils

The objective of this study was to determine the role of CH₄ loading to a landfill cover in the control of CH₄ oxidation rate (g CH₄ m⁻² d⁻¹) and CH₄ oxidation efficiency (% CH₄ oxidation) in a field setting. Specifically, we wanted to assess how much CH₄ a cover soil could handle. To achieve this objective we conducted synoptic measurements of landfill CH₄ emission and CH₄ oxidation in a single season at two Southeastern USA landfills. We hypothesized that percent oxidation would be greatest at sites of low CH₄ emission and would decrease as CH₄ emission rates increased. The trends in the experimental results were then compared to the predictions of two differing numerical models designed to simulate gas transport in landfill covers, one by modeling transport by diffusion only and the second allowing both advection and diffusion. In both field measurements and in modeling, we found that percent oxidation is a decreasing exponential function of the total CH₄ flux rate (CH₄ loading) into the cover. When CH₄ is supplied, a cover’s rate of CH₄ uptake (g CH₄ m⁻² d⁻²) is linear to a point, after which the system becomes saturated. Both field data and modeling results indicate that percent oxidation should not be considered as a constant value. Percent oxidation is a changing quantity and is a function of cover type, climatic conditions and CH₄ loading to the bottom of the cover. The data indicate that an effective way to increase the % oxidation of a landfill cover is to limit the amount of CH₄ delivered to it.     

Effects of a temporary HDPE cover on landfill gas emissions: multiyear evaluation with the static chamber approach at an Italian landfill

According to the European Landfill Directive 1999/31/EC and the related Italian Legislation (“D. Lgs. No. 36/2003”), monitoring and control procedures of landfill gas emissions, migration and external dispersions are clearly requested. These procedures could be particularly interesting in the operational circumstance of implementing a temporary cover, as for instance permitted by the Italian legislation over worked-out landfill sections, awaiting the evaluation of expected waste settlements.A possible quantitative approach for field measurement and consequential evaluation of landfill CO₂, CH₄ emission rates in pairs consists of the static, non-stationary accumulation chamber technique. At the Italian level, a significant and recent situation of periodical landfill gas emission monitoring is represented by the sanitary landfill for non-hazardous waste of the “Fano” town district, where monitoring campaigns with the static chamber have been annually conducted during the last 5 years (2005-2009). For the entire multiyear monitoring period, the resulting CO₂, CH₄ emission rates varied on the whole up to about 13,100 g CO₂ m⁻² d⁻¹ and 3800 g CH₄ m⁻² d⁻¹, respectively.The elaboration of these landfill gas emission data collected at the “Fano” case-study site during the monitoring campaigns, presented and discussed in the paper, gives rise to a certain scientific evidence of the possible negative effects derivable from the implementation of a temporary HDPE cover over a worked-out landfill section, notably: the lateral migration and concentration of landfill gas emissions through adjacent, active landfill sections when hydraulically connected; and consequently, the increase of landfill gas flux velocities throughout the reduced overall soil cover surface, giving rise to a flowing through of CH₄ emissions without a significant oxidation. Thus, these circumstances are expected to cause a certain increase of the overall GHG emissions from the given landfill site.     

Quantification of multiple methane emission sources at landfills using a double tracer technique

A double tracer technique was used successfully to quantify whole-site methane (CH₄) emissions from Fakse Landfill. Emissions from different sections of the landfill were quantified by using two different tracers. A scaled-down version of the tracer technique measuring close-by to localized sources having limited areal extent was also used to quantify emissions from on-site sources at the landfill facility, including a composting area and a sewage sludge storage pit. Three field campaigns were performed. At all three field campaigns an overall leak search showed that the CH₄ emissions from the old landfill section were localized to the leachate collection wells and slope areas. The average CH₄ emissions from the old landfill section were quantified to be 32.6 ± 7.4 kg CH₄ h⁻¹, whereas the source at the new section was quantified to be 10.3 ± 5.3 kg CH₄ h⁻¹. The CH₄ emission from the compost area was 0.5 ± 0.25 kg CH₄ h⁻¹, whereas the carbon dioxide (CO₂) and nitrous oxide (N₂O) flux was quantified to be in the order of 332 ± 166 kg CO₂ h⁻¹ and 0.06 ± 0.03 kg N₂O h⁻¹, respectively. The sludge pit located west of the compost material was quantified to have an emission of 2.4 ± 0.63 kg h⁻¹ CH₄, and 0.03 ± 0.01 kg h⁻¹ N₂O.     

Evaluation of methane emissions from Palermo municipal landfill: Comparison between field measurements and models

Methane (CH₄) diffuse emissions from Municipal Solid Waste (MSW) landfills represent one of the most important anthropogenic sources of greenhouse gas. CH₄ is produced by anaerobic biodegradation of organic matter in landfilled MSW and constitutes a major component of landfill gas (LFG). Gas recovery is a suitable method to effectively control CH₄ emissions from landfill sites and the quantification of CH₄ emissions represents a good tool to evaluate the effectiveness of a gas recovery system in reducing LFG emissions. In particular, LFG emissions can indirectly be evaluated from mass balance equations between LFG production, recovery and oxidation in the landfill, as well as by a direct approach based on LFG emission measurements from the landfill surface. However, up to now few direct measurements of landfill CH₄ diffuse emissions have been reported in the technical literature. In the present study, both modeling and direct emission measuring methodologies have been applied to the case study of Bellolampo landfill located in Palermo, Italy. The main aim of the present study was to evaluate CH₄ diffuse emissions, based on direct measurements carried out with the flux accumulation chamber (static, non-stationary) method, as well as to obtain the CH₄ contoured flux map of the landfill. Such emissions were compared with the estimate achieved by means of CH₄ mass balance equations. The results showed that the emissions obtained by applying the flux chamber method are in good agreement with the ones derived by the application of the mass balance equation, and that the evaluated contoured flux maps represent a reliable tool to locate areas with abnormal emissions in order to optimize the gas recovery system efficiency.     

Mitigation of methane emission from an old unlined landfill in Klintholm,Denmark using a passive biocover system

Methane generated at landfills contributes to global warming and can be mitigated by biocover systems relying on microbial methane oxidation. As part of a closure plan for an old unlined landfill without any gas management measures, an innovative biocover system was established. The system was designed based on a conceptual model of the gas emission patterns established through an initial baseline study. The study included construction of gas collection trenches along the slopes of the landfill where the majority of the methane emissions occurred. Local compost materials were tested as to their usefulness as bioactive methane oxidizing material and a suitable compost mixture was selected. Whole site methane emission quantifications based on combined tracer release and downwind measurements in combination with several local experimental activities (gas composition within biocover layers, flux chamber based emission measurements and logging of compost temperatures) proved that the biocover system had an average mitigation efficiency of approximately 80%. The study showed that the system also had a high efficiency during winter periods with temperatures below freezing. An economic analysis indicated that the mitigation costs of the biocover system were competitive to other existing greenhouse gas mitigation options.     

Tracer method to measure landfill gas emissions from leachate collection systems

This paper describes a method developed for quantification of gas emissions from the leachate collection system at landfills and present emission data measured at two Danish landfills with no landfill gas collection systems in place: Fakse landfill and AV Miljø. Landfill top covers are often designed to prevent infiltration of water and thus are made from low permeable materials. At such sites a large part of the gas will often emit through other pathways such as the leachate collection system. These point releases of gaseous constituents from these locations cannot be measured using traditional flux chambers, which are often used to measure gas emissions from landfills. Comparing tracer measurements of methane (CH₄) emissions from leachate systems at Fakse landfill and AV Miljø to measurements of total CH₄ emissions, it was found that approximately 47% (351 kg CH₄ d^?1) and 27% (211 kg CH₄ d^?1), respectively, of the CH₄ emitting from the sites occurred from the leachate collection systems. Emission rates observed from individual leachate collection wells at the two landfills ranged from 0.1 to 76 kg CH₄ d^?1. A strong influence on emission rates caused by rise and fall in atmospheric pressure was observed when continuously measuring emission from a leachate well over a week. Emission of CH₄ was one to two orders of magnitude higher during periods of decreasing pressure compared to periods of increasing pressure.     

Reporting central tendencies of chamber measured surface emission and oxidation

Methane emissions, concentrations, and oxidation were measured on eleven MSW landfills in eleven states spanning from California to Pennsylvania during the three year study. The flux measurements were performed using a static chamber technique. Initial concentration samples were collected immediately after placement of the flux chamber. Oxidation of the emitted methane was evaluated using stable isotope techniques. When reporting overall surface emissions and percent oxidation for a landfill cover, central tendencies are typically used to report “averages” of the collected data. The objective of this study was to determine the best way to determine and report central tendencies. Results showed that 89% of the data sets of collected surface flux have lognormal distributions, 83% of the surface concentration data sets are also lognormal. Sixty seven percent (67%) of the isotope measured percent oxidation data sets are normally distributed. The distribution of data for all eleven landfills provides insight of the central tendencies of emissions, concentrations, and percent oxidation. When reporting the “average” measurement for both flux and concentration data collected at the surface of a landfill, statistical analyses provided insight supporting the use of the geometric mean. But the arithmetic mean can accurately represent the percent oxidation, as measured with the stable isotope technique. We examined correlations between surface CH₄ emissions and surface air CH₄ concentrations. Correlation of the concentration and flux values using the geometric mean proved to be a good fit (R² = 0.86), indicating that surface scans are a good way of identifying locations of high emissions.     

Uncontrolled methane emissions from a MSW landfill surface: Influence of landfill features and side slopes

Sanitary landfills for Municipal Solid Waste (MSW) disposal have been identified as one of the most important anthropogenic sources of methane (CH₄) emissions; in order to minimize its negative effects on the environment, landfill gas (LFG) recovery is a suitable tool to control CH₄ emissions from a landfill site; further, the measurement of CH₄ emissions can represent a good way to evaluate the effectiveness of LFG recovering systems. In general, LFG will escape through any faults in the landfill capping or in the LFG collection system. Indeed, some areas of the capping can be more permeable than others (e.g. portions of a side slope), especially when considering a temporarily capped zone (covered area that is not expected to receive any further waste for a period of at least 3 months, but for engineering reasons does not have a permanent cap yet). These areas, which are characterized by abnormal emissions, are usually defined as “features”: in particular, a feature is a small, discrete area or an installation where CH₄ emissions significantly differ from the surrounding zones. In the present study, the influence that specific features have on CH₄ emissions has been investigated, based on direct measurements carried out in different seasons by means of a flux chamber to the case study of Palermo (IT) landfill (Bellolampo). The results showed that the flux chamber method is reliable and easy to perform, and the contoured flux maps, obtained by processing the measured data were found to be a suitable tool for identifying areas with abnormal (high) emissions. Further, it was found that a relationship between methane emission rates and landfill side slope can be established. Concerning the influence of the temporary HDPE cover system on CH₄ recovery efficiency, it contributed to a significant decrease of the free surface area available for uncontrolled emissions; this aspect, coupled to the increase of the CH₄ volumes collected by the LFG recovery system, led to a significant increase of the recovery efficiency.     

CH4/CO2 ratios indicate highly efficient methane oxidation by a pumice landfill cover-soil

Landfills that generate too little biogas for economic energy recovery can potentially offset methane (CH₄) emissions through biological oxidation by methanotrophic bacteria in cover soils. This study reports on the CH₄ oxidation efficiency of a 10-year old landfill cap comprising a volcanic pumice soil. Surface CH₄ and CO₂ fluxes were measured using field chambers during three sampling intervals over winter and summer. Methane fluxes were temporally and spatially variable (?0.36 to 3044 mg CH₄ m^?2 h^?1); but were at least 15 times lower than typical literature CH₄ fluxes reported for older landfills in 45 of the 46 chambers tested. Exposure of soil from this landfill cover to variable CH₄ fluxes in laboratory microcosms revealed a very strong correlation between CH₄ oxidation efficiency and CH₄/CO₂ ratios, confirming the utility of this relationship for approximating CH₄ oxidation efficiency. CH₄/CO₂ ratios were applied to gas concentrations from the surface flux chambers and indicated a mean CH₄ oxidation efficiency of 72%. To examine CH₄ oxidation with soil depth, we collected 10 soil depth profiles at random locations across the landfill. Seven profiles exhibited CH₄ removal rates of 70–100% at depths <60 cm, supporting the high oxidation rates observed in the chambers. Based on a conservative 70% CH₄ oxidation efficiency occurring at the site, this cover soil is clearly offsetting far greater CH₄ quantities than the 10% default value currently adopted by the IPCC.     

Gas production, composition and emission at a modern disposal site receiving waste with a low-organic content

AV Miljø is a modern waste disposal site receiving non-combustible waste with a low-organic content. The objective of the current project was to determine the gas generation, composition, emission, and oxidation in top covers on selected waste cells as well as the total methane (CH₄) emission from the disposal site. The investigations focused particularly on three waste disposal cells containing shredder waste (cell 1.5.1), mixed industrial waste (cell 2.2.2), and mixed combustible waste (cell 1.3). Laboratory waste incubation experiments as well as gas modeling showed that significant gas generation was occurring in all three cells. Field analysis showed that the gas generated in the cell with mixed combustible waste consisted of mainly CH₄ (70%) and carbon dioxide (CO₂) (29%) whereas the gas generated within the shredder waste, primarily consisted of CH₄ (27%) and nitrogen (N₂) (71%), containing no CO₂. The results indicated that the gas composition in the shredder waste was governed by chemical reactions as well as microbial reactions. CH₄ mass balances from three individual waste cells showed that a significant part (between 15% and 67%) of the CH₄ generated in cell 1.3 and 2.2.2 was emitted through leachate collection wells, as a result of the relatively impermeable covers in place at these two cells preventing vertical migration of the gas. At cell 1.5.1, which is un-covered, the CH₄ emission through the leachate system was low due to the high gas permeability of the shredder waste. Instead the gas was emitted through the waste resulting in some hotspot observations on the shredder surface with higher emission rates. The remaining gas that was not emitted through surfaces or the leachate collection system could potentially be oxidized as the measured oxidation capacity exceeded the potential emission rate. The whole CH₄ emission from the disposal site was found to be 820 ± 202 kg CH₄ d⁻¹. The total emission rate through the leachate collection system at AV Miljø was found to be 211 kg CH₄ d⁻¹. This showed that approximately ¼ of the emitted gas was emitted through the leachate collections system making the leachate collection system an important source controlling the overall gas migration from the site. The emission pathway for the remaining part of the gas was more uncertain, but emission from open cells where waste is being disposed of or being excavated for incineration, or from horizontal leachate drainage pipes placed in permeable gravel layers in the bottom of empty cells was likely.     

Assessment of the methane oxidation capacity of compacted soils intended for use as landfill cover materials

The microbial oxidation of methane in engineered cover soils is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes of low methane generation rates. A laboratory column study was conducted in order to derive design criteria that enable construction of an effective methane oxidising cover from the range of soils that are available to the landfill operator. Therefore, the methane oxidation capacity of different soils was assessed under simulated landfill conditions. Five sandy potential landfill top cover materials with varying contents of silt and clay were investigated with respect to methane oxidation and corresponding soil gas composition over a period of four months. The soils were compacted to 95% of their specific proctor density, resulting in bulk densities of 1.4-1.7 g cm⁻³, reflecting considerably unfavourable conditions for methane oxidation due to reduced air-filled porosity. The soil water content was adjusted to field capacity, resulting in water contents ranging from 16.2 to 48.5 vol.%. The investigated inlet fluxes ranged from 25 to about 100 g CH₄ m⁻² d⁻¹, covering the methane load proposed to allow for complete oxidation in landfill covers under Western European climate conditions and hence being suggested as a criterion for release from aftercare. The vertical distribution of gas concentrations, methane flux balances as well as stable carbon isotope studies allowed for clear process identifications. Higher inlet fluxes led to a reduction of the aerated zone, an increase in the absolute methane oxidation rate and a decline of the relative proportion of oxidized methane. For each material, a specific maximum oxidation rate was determined, which varied between 20 and 95 g CH₄ m⁻² d⁻¹ and which was positively correlated to the air-filled porosity of the soil. Methane oxidation efficiencies and gas profile data imply a strong link between oxidation capacity and diffusive ingress of atmospheric air. For one material with elevated levels of fine particles and high organic matter content, methane production impeded the quantification of methane oxidation potentials. Regarding the design of landfill cover layers it was concluded that the magnitude of the expected methane load, the texture and expected compaction of the cover material are key variables that need to be known. Based on these, a column study can serve as an appropriate testing system to determine the methane oxidation capacity of a soil intended as landfill cover material.     

Spatial variability of nitrous oxide and methane emissions from an MBT landfill in operation: Strong N2O hotspots at the working face

Mechanical biological treatment (MBT) is an effective technique, which removes organic carbon from municipal solid waste (MSW) prior to deposition. Thereby, methane (CH₄) production in the landfill is strongly mitigated. However, direct measurements of greenhouse gas emissions from full-scale MBT landfills have not been conducted so far. Thus, CH₄ and nitrous oxide (N₂O) emissions from a German MBT landfill in operation as well as their concentrations in the landfill gas (LFG) were measured. High N₂O emissions of 20–200 g CO₂ eq. m^?2 h^?1 magnitude (up to 428 mg N m^?2 h^?1) were observed within 20 m of the working face. CH₄ emissions were highest at the landfill zone located at a distance of 30–40 m from the working face, where they reached about 10 g CO₂ eq. m^?2 h^?1. The MBT material in this area has been deposited several weeks earlier. Maximum LFG concentration for N₂O was 24.000 ppmv in material below the emission hotspot. At a depth of 50 cm from the landfill surface a strong negative correlation between N₂O and CH₄ concentrations was observed. From this and from the distribution pattern of extractable ammonium, nitrite, and nitrate it has been concluded that strong N₂O production is associated with nitrification activity and the occurrence of nitrite and nitrate, which is initiated by oxygen input during waste deposition. Therefore, CH₄ mitigation measures, which often employ aeration, could result in a net increase of GHG emissions due to increased N₂O emissions, especially at MBT landfills.     

Future landfill emissions and the effect of final cover installation--a case study

Municipal solid waste (MSW) landfills are potential long-term sources of emissions. Hence, they need to be managed after closure until they do not pose a threat to humans or the environment. The case study on the Breitenau MSW landfill was performed to evaluate future emission levels for this site and to illustrate the effect of final cover installation with respect to long-term environmental risks. The methodology was based on a comprehensive assessment of the state of the landfill and included analysis of monitoring data, investigations of landfilled waste, and an evaluation of containment systems. A model to estimate future emission levels was established and site-specific predictions of leachate emissions were presented based on scenario analysis. The results are used to evaluate the future pollution potential of the landfill and to compare different aftercare concepts in view of long-term emissions. As some leachable substances became available for water flow during cover construction due to a change in the water flow pattern of the waste, a substantial increase in leachate concentrations could be observed at the site (e.g. concentrations of chloride increased from 200 to 800 mg/l and of ammonia-nitrogen from 140 to about 500 mg/l). A period of intensive flushing before the final cover installation could have reduced the amount of leachable substances within the landfill body and rapidly decreased the leachate concentrations to 11 mg Cl/l and 79 mg NH₄-N/l within 50 years. Contrarily, the minimization of water infiltration is associated with leachate concentrations in a high range for centuries (above 400 mg Cl/l and 200 mg NH₄-N/l) with low concomitant annual emission loads (below 12 kg/year of Cl or 9 kg/year of NH₄-N, respectively). However, an expected gradual decrease of barrier efficiency over time would be associated with higher emission loads of 50 kg of chloride and 30 kg of ammonia-nitrogen at the maximum, but a faster decrease of leachate concentration levels.     

Influence of aeration on CH4, N2O and NH3 emissions during aerobic composting of a chicken manure and high C/N waste mixture

Co-composting of chicken manure, straw and dry grasses was investigated in a forced aeration system to estimate the effect of aeration rates on NH₃, CH₄ and N₂O emissions and compost quality. Continuous measurements of gas emissions were carried out and detailed gas emission patterns were obtained using an intermittent-aeration of 30 min on/30 min off at rates of 0.01 (A1), 0.1 (A2) and 0.2 (A3) m³ min⁻¹ m⁻³. Concentrations of CH₄ and N₂O at the low aeration rate (A1) were significantly greater than those at the other two rates, but there was no significant difference between the A2 and A3 treatments. CH₄ and N₂O emissions for this mixture could be controlled when the composting process was aerobic and ammonia emissions were reduced at a lower aeration rate. Comparison of CH₄, N₂O, NH₃ emissions and compost quality showed that the aeration rate of the A2 treatment was superior to the other two aeration rates.     

Availability and properties of materials for the Fakse Landfill biocover

Methane produced in landfills can be oxidized in landfill covers made of compost; often called biocovers. Compost materials originating from seven different sources were characterized to determine their methane-oxidizing capacity and suitability for use in a full-scale biocover at Fakse Landfill in Denmark. Methane oxidation rates were determined in batch incubations. Based on material availability, characteristics, and the results of batch incubations, five of the seven materials were selected for further testing in column incubations. Three of the best performing materials showed comparable average methane oxidation rates: screened garden waste compost, sewage sludge compost, and an unscreened 4-year old garden waste compost (120, 112, and 108 g m⁻² d⁻¹, respectively). On the basis of these results, material availability and cost, the unscreened garden waste compost was determined to be the optimal material for the biocover. Comparing the results to criteria given in the literature it was found that the C/N ratio was the best indicator of the methane oxidation capacity of compost materials. The results of this work indicate that batch incubations measuring methane oxidation rates offer a low-cost and effective method for comparing compost sources for suitability of use in landfill biocovers.     

Improving the aeration of critical fine-grained landfill top cover material by vegetation to increase the microbial methane oxidation efficiency

The natural methane oxidation potential of methanotrophic bacteria in landfill top covers is a sustainable and inexpensive method to reduce methane emissions to the atmosphere. Basically, the activity of methanotrophic bacteria is limited by the availability of oxygen in the soil. A column study was carried out to determine whether and to what extent vegetation can improve soil aeration and maintain the methane oxidation process. Tested soils were clayey silt and mature compost. The first soil is critical in light of surface crusting due to vertical erosion of an integral part of fine-grained material, blocking pores required for the gas exchange. The second soil, mature compost, is known for its good methane oxidation characteristics, due to high air-filled porosity, favorable water retention capacity and high nutrient supply. The assortment of plants consisted of a grass mixture, Canadian goldenrod and a mixture of leguminous plants. The compost offered an excellent methane oxidation potential of 100% up to a CH₄-input of 5.6 l CH₄ m⁻² h⁻¹. Whereas the oxidation potential was strongly diminished in the bare control column filled with clayey silt even at low CH₄-loads. By contrast the planted clayey silt showed an increased methane oxidation potential compared to the bare column. The spreading root system forms secondary macro-pores, and hence amplifies the air diffusivity and sustain the oxygen supply to the methanotrophic bacteria. Water is produced during methane oxidation, causing leachate. Vegetation reduces the leachate by evapotranspiration. Furthermore, leguminous plants support the enrichment of soil with nitrogen compounds and thus improving the methane oxidation process. In conclusion, vegetation is relevant for the increase of oxygen diffusion into the soil and subsequently enhances effective methane oxidation in landfill cover soils.