Formation of chloroarenes upon gas-phase pyrolysis and slow combustion of benzene-HCl mixtures

Pyrolysis (800–900°C, ca. 5 s) of benzene/HC1 mixtures leads to chlorobenzene (1) even in a reducing environment of H₂ and/or CH₄. With added oxygen, 1 is formed even at 550°C; such slow combustions also yield chlorinated phenols and dibenzofurans.     

Effects of solution conditions on the precipitation of phosphate for recovery. A thermodynamic evaluation

To understand the effects of solution conditions on the precipitation of calcium phosphates from wastewater for recovery, a computer programme PHREEQC was employed to calculate the speciation and saturation-index (SI) with respect to hydroxyapatite of a chemically defined precipitation system, which contains phosphate of 1–200 mg P/l, with Ca/P molar ratios of one to 10 times of the stoichiometric calcium to phosphorus molar ratio of hydroxyapatite, at a pH range of 7.0–11.0. The results show that the SI is respectively the logarithmic function of the phosphate concentration and the calcium concentration, increasing with the increase of either of them; the SI is a polynomial function of the solution pH value and increases with its increase, and the effect of solution pH value is due to its influence on base uptake of the precipitation reaction and the speciation of phosphate and calcium ions; the SI is also a logarithmic function of the solution ionic strength but decreases with its increase; at the temperature range of 5–30 °C the SI increases linearly with solution temperature and the effect of temperature is also due to its influence on the speciation of phosphate and calcium ions.     

Photochemical oxidation of reduced sulfur compounds in an urban location based on short time monitoring data

This study examines the oxidation of reduced sulfur compounds (RSCs) in urban ambient air. The photochemical conversions of RSC (such as DMS, CS₂, H₂S, DMDS, and CH₃SH) to a further oxidized form (e.g., SO₂, MSA, and H₂SO₄) were assessed using a photochemical box model. For our model simulation of RSC oxidation, measurements were taken at an urban monitoring station in Seoul, Korea (37.6° N, 127° E) during three separate time periods (e.g., Sept. 17–18, Oct. 23, and Oct. 27–28, 2003). The results indicate that DMS and H₂S were the dominant RSCs with concentrations of 370 ± 140 and 110 ± 60 pptv, respectively. The photochemical conversion of DMDS to SO₂ was found to occur more efficiently than other RSCs. The overall results of our study suggest that photochemical conversion of RSCs accounted for less than 15% of the observed SO₂ during the measurement period. The SO₂ production from DMS oxidation (mainly by the reaction with OH) was found to be affected primarily by the abstraction channel due to high NO_x levels during the experimental conditions.     

Impacts of charcoal characteristics on sorption of polycyclic aromatic hydrocarbons

Sorption of three polycyclic aromatic hydrocarbons (PAHs, phenanthrene, anthracene and pyrene) on three charcoals and their precursor substance (sawdust) was studied. The charcoals obtained by heating at 400 °C for different periods were different in chemical composition and structure. Sorption characteristics were described by a Polanyi–Dubinin–Manes model combined with poly-parameter linear free energy relationships. The results revealed that though partition could not be neglected for sawdust and charcoal containing large sawdust residue, adsorption controlled the sorption of PAHs on matured charcoals, where π–π electron donor–acceptor (EDA) exerted as the main molecular-scale interactions. Charring elevated partition coefficients (K_oc) of the three PAHs more than one order of magnitude, which ranged from 10^5.74 to 10^6.58 on charcoals (for PAHs at equilibrium concentration C_e = 0.005S_w). Adsorption increased with the aromaticity of the charcoals, however, polar aromatic structure may stimulate sorption of PAHs due to the presence of π–π EDA interactions.     

Bioaccumulation of anthropogenic contaminants by detritivorous fish in the Río de la Plata estuary: 1-aliphatic hydrocarbons

The temporal variability and bioaccumulation dynamics of C_12–25 n-alkanes, isoprenoids and unresolved aliphatic hydrocarbons (UCM) were studied in a detritivorous fish (Sábalo: Prochilodus lineatus) collected from 1999 to 2005 in the sewage impacted Buenos Aires coastal area. Fish muscles contain huge amounts of n-C_12–25 (165 ± 93, 70 ± 48 or 280 ± 134 μg g⁻¹, dry, fresh and lipid weight, respectively) and UCM (931 ± 560, 399 ± 288 and 1567 ± 802 μg g⁻¹) reflecting the chronic bioaccumulation of fossil fuels from sewage particulates. On a temporal basis, lipid normalized aliphatic concentrations peaked by the end of 2001–2002 during the rainiest period over the last four decades (1750 vs. 1083 ± 4.6 mm in 1999, 2004 and 2005), reflecting an enhanced exposition due to massive anthropogenic fluxes from Metropolitan Buenos Aires in wet years. The hydrocarbon composition in fish muscles is enriched in n-C_15–17 and isoprenoids relative to a fresh crude oil and settling particulates, with fresher signatures during the 2001–2002 maxima. Fish/settling material bioaccumulation factors (BAFs: 0.4–6.4 dry weight or 0.07–0.94 lipid-organic carbon) plotted against K_ow showed a parabolic pattern maximizing at n-C_14–18 and isoprenoids. The optimal bioaccumulation window corresponds to highly hydrophobic (log K_ow: 7.2–9.9), intermediate-size C_14–18 n-alkanes and C_15–20 isoprenoids (MW: 198–282; length: 17.9 to 25.4 Å) with melting points ranging from −19.8 to 28 °C. The uptake efficiency is inversely correlated to melting points and increased from 75% for n-C₂₅ to above 90% for n-C_14–15 and isoprenoids.     

Combined steam distillation and electrochemical peroxidation (ECP) treatment of river sediment contaminated by PCBs

A combined treatment process utilizing steam distillation followed by electrochemical peroxidation (ECP) has been utilized to remove >90% of the polychlorinated biphenyls (PCBs) in St. Lawrence River sediment and destroy 95% of the PCBs recovered in the condensate. 2 l of condensate were collected by boiling 500 grams of sediment containing 4.3 mg PCBs. Most of the PCBs (82.3%) were recovered as a small volume (<1 ml) of yellow oil floating on the condensate and coating glassware surfaces. The aqueous phase PCBs (182 μg/l) were destroyed (95%) by three sequential ECP treatments at 16.8°C and pH 5, utilizing 1 ml of H₂O₂ (3%) and periodically reversed current (0.75–1.0 A @ 10 volts). Oxidation is primarily mediated by hydroxyl radicals produced by the reaction of hydrogen peroxide with electrochemically generated ferrous iron (Fenton's reagent). This work suggests steam extraction, in combination with advanced oxidation technologies, provides an effective treatment strategy for contaminated solids.     

Brominated-chlorinated diphenyl ethers formed by thermolysis of polybrominated diphenyl ethers at low temperatures

Polybrominated diphenyl ethers (PBDEs) are a group of brominated flame retardants (BFRs) used mainly as additives in different kinds of plastic material. Various PBDEs are found in all environmental compartments as well as in tissue and blood serum of animals and humans due to their persistence and tendency to bioaccumulate. Emission of PBDEs into the environment can occur during recycling of PBDE-containing plastic material or during their uncontrolled or insufficient combustion as e.g. in accidental fires or landfill fires. Under these circumstances, PBDEs can also function as precursor molecules for the formation of polybrominated dibenzodioxins (PBDDs) and dibenzofurans (PBDFs). In this study, we qualitatively investigated the reaction of two PBDE congeners, 2,2′,4,4′-tetrabromo diphenyl ether (BDE 47) and 2,2′,4,4′,5,5′-hexabromo diphenyl ether (BDE 153), as well as hexabromobenzene (HBB), a flame retardant used in the past, when exposed to temperatures between 250 °C and 500 °C. The formed reaction products were analysed by high resolution gas chromatography–low resolution mass spectrometry (HRGC-LRMS). Among others brominated–chlorinated diphenyl ethers were formed by chlorodebromination of the PBDEs. In addition, thermolysis of BDE 47 and BDE 153 in the presence of tetrachloromethane as model substance for an organic chlorine source was studied. Thermal treatment of HBB resulted in the formation of brominated–chlorinated benzenes.     

Photocatalytic activity of the calcined H-titanate nanowires for photocatalytic oxidation of acetone in air

Hydrogen titanate (H-titanate) nanowires were prepared via a hydrothermal reaction of TiO₂ powders (P25) in KOH solutions and then calcined at various temperatures. The phase structure, crystallite size, morphology, specific surface area, and pore structures of the calcined H-titanate nanowires at various temperatures were characterized with field emission scanning electron microscope, X-ray diffraction, transmission electron microscopy and nitrogen adsorption–desorption isotherms, and their photocatalytic activities were evaluated by photocatalytic oxidation of acetone in air. With increasing calcination temperature, the specific surface area and porosity of the calcined samples steadily decreased. At a calcination temperature range of 400–600 °C, the calcined H-titanate nanowires showed higher photocatalytic activity than P25 powders for photocatalytic oxidation of acetone. Especially, at 500 °C, the calcined H-titanate nanowires showed the highest photocatalytic activity, which exceeded that of P25 by a factor of about 1.8 times. This can be attributed to the synergetic effect of larger specific surface area, higher pore volume and the presence of brookite TiO₂. With further increase in the calcination temperature (700–900 °C), the photocatalytic activity of the samples decreased obviously owing to the growth of TiO₂ crystallites.     

Recycling of flame retardants containing printed circuits: A study of the possible formation of polyhalogenated dibenzodioxins/-furans

The generation of halogenated dibenzo-p-dioxins/-furans could be expected during recycling of printed circuits containing flame retardants. The presence of precursor substances (e.g. flame retardants like tetrabromobis-phenol A or PCB), partly elevated temperatures, and catalytical effects of copper seem to represent typical formation conditions for “dioxins”. To control the possible contamination of granulated material and thus of work places, in a pilot plant a test run was carried out with a hammer mill and an impact grinder. The air samples examined did not contain PXDD/F residues and the shredded material was contaminated only with PBDD/F at very low concentrations (0.03 – 1.13 ng/g). A test with printed circuits under thermal stress up to 300 °C in an oven generated low amounts of PBDD/F (0.74 – 4.51 ng/g). These tests provide proof that printed circuits can be recycled.     

Multivariate curve resolution of multidimensional excitation-emission quenching matrices of a Laurentian soil fulvic acid

Fluorescence excitation–emission matrices (EEM) of aqueous solutions of Laurentian soil fulvic acid (LFA) at three concentrations (50, 75 and 100 mg/l) were obtained at two pH values (pH = 4.0 and 6.0) and as function of the Cu(II) ion concentration. The presence of Cu(II) ion provokes quenching of the intrinsic LFA fluorescence due to complex formation. Multivariate curve resolution (MCR-ALS) was used to successfully decompose single EEM into excitation and emission spectra for the detected components. Moreover, multidimensional (up to six dimensions) data matrices were generated by adding EEM collected as function of the LFA and Cu(II) concentrations and pH. MCR-ALS was able to resolve the excitation and emission spectra from these multidimensional data matrices given further information about the spectral variation profiles induced by the experimental factors. Conditional stability constants (log K_LFACu) were calculated from the quenching profiles observed as function of the Cu(II) concentration, as well as, their trends as function of pH and LFA concentration were obtained – average (and standard deviation) of log K_LFACu = 4.6 ± 0.2. This EEM/MCR-ALS methodology constitutes a new tool for the study of natural organic matter under varying experimental conditions that characterize natural environmental systems.     

Development of a new hydrocarbon index for oil-in-water

A new robust method for determination of hydrocarbons in water without use of Freon^™ or other halogenated solvents has been validated and subjected to an interlaboratory exercise. The method is based on extraction with a light hydrocarbon (boiling point in the 39–69°C range), followed by cleanup for removal of polar components and detection by gas chromatography (GC) with flame ionisation (FID) detection. The performance characteristics of the method are comparable with that of the previous Freon-IR method with recoveries in the 60–80% range and reproducibility (between laboratory variations) of about 30%.

A screening method for hydrocarbons in the range 5 ppm and above based on infrared spectroscopy (IR), and a promising method for detection of low levels based on solid phase extraction (SPE) has been tested and validated.     

Effect of a base-catalyzed dechlorination process on the genotoxicity of PCB-contaminated soil

We evaluated the genotoxicity of dichloromethane (DCM) extracts of PCB-contaminated soil before and after the soil had been treated by a base-catalyzed dechlorination process. The treatment process involves heating a mixture of the soil, polyethylene glycol (or hydrocarbons with boiling points of 310–387°C), and sodium hydroxide to 250–350°C. Dechlorination reduced by >99% the PCB concentration of the soil, which was initially 2,200 ppm. The DCM extracts of both control and treated soils were not mutagenic in strain TA100 of Salmonella, but they were mutagenic in strain TA98. Based on results in strain TA98, the base-catalyzed dechlorination process reduced the mutagenic potency of the soil by approximately one-half. The DCM extracts of the soils before and after treatment were equally genotoxic in a prophage-induction assay in . , which detects some chlorinated organic carcinogens that are not detected by the Salmonella mutagenicity assay. These results suggest that treatment of PCB-contaminated soil by base-catalyzed dechlorination reduced the mutagenicity of the soil slightly.     

Development of a terrestrial vertebrate model for assessing bioavailability of cadmium in the fence lizard (Sceloporus undulatus) and in ovo effects on hatchling size and thyroid function

In the terrestrial environment, standardized protocols are available for measuring the exposure and effects of contaminants to invertebrates, but none currently exist for vertebrates. In an effort to address this, we proposed that developing lizard embryos may be used as a terrestrial vertebrate model. Lizard eggs may be particularly susceptible to soil contamination and in ovo exposure may affect hatchling size, mortality, as well as thyroid function. Toxicant-induced perturbations of thyroid function resulting from in ovo chemical exposure may result in toxicity during the critical perinatal period in reptiles. Fertilized Eastern fence lizard (Sceloporus undulatus) eggs were placed in cadmium (Cd)-spiked expanded perlite (0, 1.48, 14.8, 148, 1480, 14 800 μg Cd/g, nominal concentrations), artificially incubated at 28 °C, and examined daily for mortality. Whole lizard hatchlings as well as failed hatches were homogenized in ethanol and the homogenate was divided for Cd body residue analysis and thyroid hormone (triiodothyronine (T₃) and thyroxine (T₄)) analyses. Acute mortality was observed in the two highest doses (1480 and 14 800 μg Cd/g). Cadmium body residues showed a higher internal concentration with increasing exposure concentration indicating uptake of Cd. There was a decrease in T₃:T₄ ratio at the highest surviving dose (148 μg Cd/g), however, there were no differences observed in hatchling size measured as weight and snout-vent length, or in whole body thyroid hormone levels. In summary, this study has shown Cd amended to a solid phase representing soil (perlite) can traverse the thin, parchment-like shell membrane of the fence lizard egg and bioaccumulate in lizard embryos. We believe this study is a good first step in investigating and evaluating this species for use as a model.     

Gas phase naphthalene chlorination

Chlorination of naphthalene by Cl atoms has been studied in the gas phase. The chlorinating agent was produced by γ-radiolysis of tetrachloromethane. At low conversions only monosubstituted products are observed. Both isomers are formed, the yield of 1-chloronaphthalene exceeding that one of its isomer. The extent of the addition reaction increases with the temperature. The relative Arrhenius plot of observed rate constants is linear over the temperature range investigated (60–120 °C) and its slope corresponds to a difference of 11.0 kJ/mol between the activation energies of 2-chloronaphthalene and 1-chloronaphthalene.     

Investigation on the adsorption capability of egg shell membrane towards model textile dyes

Adsorption isotherms of Direct Red 80 (DR80) and Acid Blue 25 (AB25) on the egg shell membrane (ESM) were performed at 20 ± 1 °C. Physical characteristics of ESM such as surface area and presence of functional groups were verified. The Fourier transform infra-red (FTIR) spectra proved the presence of fuctional groups such as hydroxyl, amine and carbonyl groups in ESM. The surface area of ESM was found to be 2.2098 m²/g. The effects of operational parameters such as initial dye concentration, pH₀, contact time, particle size and ESM doses were studied. The Langmuir, Freundlich, BET, Redlich-Peterson and Temkin adsorption models were applied to describe the equilibrium isotherms. The pseudo-first-order and pseudo-second-order kinetics models were examined to evaluate the kinetics data at different pH₀ values (2–12) and the rate constants were calculated. Maximum desorption of 81.8% was achieved for both dyes in aqueous solution at pH₀ 12. Also scanning electron micrographs (SEM) of the treated and untreated adsorbent were performed. Results indicate that ESM could be employed as a natural and Eco-Friendly adsorbent material for the removal of trace organics in solutions.     

Biomimetic chemical degradation of polychlorobiphenyls below 100°C

PCBs were rapidly degraded by hydroxy radicals formed in the biomimetic degradation systems of superoxide, ferric chloride, and hydrogen peroxide at high concentrations below 100°C. The degradation rates of Kanechlor KC 300, KC 400, KC 500 and KC 600 were 95.4%, 89.1%, 59.9% and 47.9%, respectively. The generation of carbon dioxide gas was recognized and chloride ion showed 89.9 – 102.7% of the theoretical yield in the degradation of KC 300, KC 400 and KC 500.     

Dechlorination of polychlorinated biphenyls, dibenzo-p-dioxins and dibenzofurans on fly ash

Dechlorination of commercial mixtures of polychlorinated biphenyls (PCB) as well as polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) on extracted and non-extracted fly ash obtained from municipal waste incinerator (MWI) was studied in closed systems under nitrogen atmosphere at temperatures of 260°C and 340°C. Decomposition results (given as the difference between PCB or PCDD/F molar amounts before and after the experiment (in %) due predominantly to dechlorination reactions) and detoxification data (expressed similarly but related to toxic PCB and PCDD/F congeners only and given in I-TEQ units) are reported. Detoxification of Delor 105/80T at 260°C and 340°C at a loading of 0.65 wt% was 99.48% and 100%, respectively. The decomposition of Delor 103 at 340°C and for the loading of 0.75 wt% corresponded to 99.99%. The detoxification capability of PCDD/Fs on extracted and non-extracted fly ash for loading of 130 and 264 ng/0.4 g of fly ash at 340°C made 96 and 98%, respectively.     

Behavior of PAHs during cold storage of historically contaminated soil samples

The stability of historically polycyclic aromatic hydrocarbon (PAH)-contaminated soils during cold storage was investigated. Samples from two former manufactured gas plants exhibited quantitative recoveries of PAHs over the whole period of sample holding at 4 °C in the dark (8–10 months), whereas significant losses of PAHs were observed for soils received from a former railroad sleeper preservation plant with low molecular weight compounds being notably more affected compared to heavier PAHs. Already after 2 weeks of holding time, 3-ring PAHs in one of theses samples were down to 29–73% of the initial concentration and significant losses were observed for up to 5-ring compounds. Dissipation of PAHs was found to be predominantly due to aerobic microbial metabolism since sodium azide poisoned samples showed quantitative recoveries for all PAHs over the entire storage time of 3 months. A similar stabilizing effect was observed for freezing at −20 °C as means of preservation. Except for acenaphthene, no significant loss for any of the PAHs was observed over 6 weeks of holding time. Eventually, selected chemical, physical, and biological parameters of two soils were investigated and identified as potential indicators for the stability of PAH-contaminated soil samples.     

As(V) adsorption on amorphous iron oxide: Triple layer modelling

The adsorption of As(V) by amorphous iron oxide was investigated at 25°C, 0.01 M NaNO₃ background electrolyte as a function of solution pH(4–10) at three initial As(V) concentrations and two Fe(III) concentrations. As(V) adsorption increased with decreasing pH. A modified Langmuir isotherm has been used for describing an equilibrium partition existing between solid and liquid phases. The triple-layer model was used for simulating As(V) adsorption on iron oxide surface. This model was able to describe As(V) adsorption over the pH range 4–10, all at the concentrations of As(V) and Fe(III) studied. =Fe(H₂AsO₄)⁰, = Fe(HAsO₄)⁻ and = Fe(AsO₄)²⁻ have been shown through simulation with inner-sphere complexation products to be more consistent with experimental adsorption observations than complexation with other surface species.     

Thermolysis of 2,4,6-trichlorophenol chemisorbed on aluminium oxides as example of fly ash mediated surface catalysis reaction in PCDD/PCDF formation

The influence of aluminium cation as a strong electrophilic centre on the thermolysis of chlorophenols chemisorbed on Al(OH)₃ surface was investigated. If thermolysis is carried out at 300 °C the spontaneous rupture of the bond between aluminium and oxygen of phenol takes place in the temperature range of 260–280 °C. The thermolysis of chlorophenoxy aluminium compounds occurs through homolytic and heterolytic bond cleavage. In the case of heterolytic cleavage the leaving chlorophenoxy anion causes a simultaneous formation of the aluminium cation, which is the driving force for the rearrangement of the unstable intermediate. By homolytic cleavage of the Al–O bond the chlorophenoxy radical is formed. The isolation of reaction products of the thermolysis of the system Al(OH)₃/2,4,6-trichlorophenol gave five isomers of dimeric compounds of resonance stabilised 2,4,6-trichlorophenoxy radical. The compounds are stable in nonaqueous, aprotic solution, but they are very sensitive to acid catalysis. They quickly transform into aromatic hydroxydiphenyl ethers. The process of dechlorination and aromatisation of cyclohexadienone dimers gives PCDD/PCDF.