用环己酮废水合成阳离子沥青乳化剂

以环己酮生产废水(以下简称废水)为溶剂,以木质素、三乙烯四胺及甲醛为原料,通过Mannich反应制备了阳离子沥青乳化剂木质素胺。实验结果表明,制备木质素胺的最佳工艺条件为:反应温度85℃,反应时间5 h,n(甲醛):n(三乙烯四胺)=3.0。经FTIR表征,以废水为溶剂和以去离子水为溶剂所制备的木质素胺结构相同。以实验制备的木质素胺为乳化剂制成的乳化沥青的性能指标达到JTG E20—2011《公路工程沥青及沥青混合料试验规程》的指标。     

Preparation of Cationic Asphalt Emulsifier from Cyclohexanone Wastewater

以环己酮生产废水(以下简称废水)为溶剂,以木质素、三乙烯四胺及甲醛为原料,通过Mannich反应制备了阳离子沥青乳化剂木质素胺.实验结果表明,制备木质素胺的最佳工艺条件为:反应温度85℃,反应时间5h,n(甲醛)∶n(三乙烯四胺)=3.0.经FTIR表征,以废水为溶剂和以去离子水为溶剂所制备的木质素胺结构相同.以实验制备的木质素胺为乳化剂制成的乳化沥青的性能指标达到JTG E20-2011《公路工程沥青及沥青混合料试验规程》的指标.     

改性蚁酸木质素的制备与应用

采用加拿大一枝黄花茎杆为原料提取蚁酸木质素，通过氧化或接枝复合的方法对蚁酸木质素进行改性，对改性产物进行了FTIR和SEM表征。实验结果表明：接枝复合改性产物中存在-CONH的接枝复合链，氧化改性产物基本保持了蚁酸木质素原来的吸收峰；采用接枝复合改性产物处理初始质量浓度为50 mg/L的亚甲基蓝废水，在废水pH 7、吸附时间4 h、改性产物加入量22 mg/mL的条件下，亚甲基蓝去除率为90.94%；采用氧化改性产物处理相同亚甲基蓝废水，在废水pH 10、吸附时间12 h、改性产物加入量22 mg/mL的条件下，亚甲基蓝去除率为81.93%。     

改性双氰胺-甲醛絮凝脱色剂的制备与应用

通过在原料中引入尿素，合成出了改性双氰胺-甲醛絮凝脱色剂，并应用到印染废水处理中。采用正交实验方法确定了最佳合成条件，实验结果表明，在反应温度65℃、反应时间3h、反应物配比n（双氰胺）：n（尿素）：n（氯化铵）：n（甲醛）为0．714：0．286：0．9：1．4的最佳条件下，改性双氰胺-甲醛絮凝脱色剂具有优异的絮凝脱色性能，对实际印染废水的脱色率和COD去除率可分别达到99％和93．4％。     

木质素基聚合物的制备及亚甲基蓝的吸附

以木质素磺酸钠为原料单体、环氧氯丙烷为交联剂,采用反相乳液聚合法制备了木质素磺酸钠交联聚合物(SLCP),并将其用于水中有机染料的吸附。表征结果显示:SLCP基本保留了木质素磺酸钠的骨架和官能团,具有良好的热稳定性。实验结果表明:SLCP对亚甲基蓝(MB)有较好的吸附选择性,在加入量为0.5 g/L时就有较高的吸附效率;在溶液p H2~6范围内吸附量随溶液p H增大而迅速提高,溶液p H6后吸附量趋于稳定;最佳吸附温度为35℃;在SLCP加入量0.5 g/L、溶液p H 6.5、吸附温度25℃、初始MB质量浓度100.5 mg/L的条件下,吸附150 min基本可达平衡,吸附平衡时的吸附量和MB去除率分别为191.2 mg/g和95.1%;SLCP对MB的吸附符合Langmuir等温吸附模型,吸附动力学符合Lagergren拟二级动力学方程。     

NaOH改性活性炭的表面特征及吸附甲醛的性能

研究了NaOH改性活性炭(AC)的表面官能团变化特征及其吸附甲醛的性能.实验结果表明:改性AC表面的羧基、酚羟基、内酯基等官能团均与NaOH发生化学反应;质量分数为30%的NaOH溶液对AC表面的清洗作用最大,能将AC表面的杂质基本清除,此时AC表面羧基、酚羟基、内酯基和羰基浓度均达到最大;NaOH溶液质量分数为30%时,改性AC吸附甲醛的效果最好;改性AC表面酚羟基浓度的大小与改性AC吸附甲醛气体穿透时间的长短呈正比.     

催化臭氧氧化法处理甲醛废水

用异丙醇钛盐表面改性法制备TiO2／SiO2催化剂，对甲醛废水进行催化臭氧氧化处理。通过比表面积的BET测定法、X射线衍射和拉曼光谱等分析方法对TiO2／SiO2催化剂进行了表征，考察了TiO2／SiO2催化剂加入量、臭氧流量及溶液pH等因素对甲醛催化臭氧氧化效果的影响。实验结果表明，在SiO2表面，TiO2微晶粒子以锐钛矿型高度分散；在甲醛质量浓度700mg／L、COD1000mg／L、TiO2／SiO2催化剂加入量2．0g、臭氧流量2．5mg／min、溶液pH8．5的条件下，催化臭氧氧化反应30min后，甲醛质量浓度由700mg／L降至39mg／L，COD去除率认到87．5％．     

新型脱色絮凝剂木素季胺盐的研制及其絮凝性能与机理的研究

以从造纸黑液中提取的木质素为原料，合成木素季胺盐絮凝剂。通过正交实验，确定了反应物料比、活化时间、催化剂浓度，反应时间等因素对合成的影响，优化出絮凝剂合成工艺条件。     

一种新型聚合物分散剂的制备及表征

以甲基丙烯酸和丙烯磺酸钠为单体、过硫酸铵溶液为引发剂合成聚合物分散剂（PMS）。最佳合成条件：单体总质量为60g，甲基丙烯酸和丙烯磺酸钠的摩尔比为3．0，过硫酸铵溶液加入量为12g，亚硫酸氢钠加入最为1g，反应温度为75℃。对最佳条件下制得的PMS进行应用实验，当100g陶瓷氧化铝粉末中PMS加入量为0．5g时，浆料的黏度较小，分散效果良好。PMS属于非品态聚合物，热稳定性良好，相对分子质量为2127。     

环保型脲醛树脂胶粘剂的合成研究

介绍了聚乙烯醇(PVA)、三聚氰胺在脲醛树脂胶粘剂合成过程中所起的改性作用,研究了反应温度、反应体系pH、甲醛与尿素摩尔比、PVA和三聚氰胺用量对脲醛树脂胶粘剂性能的影响。试验结果表明,在反应温度为80℃、反应体系pH为5．0、甲醛与尿素摩尔比为1．5、PVA和三聚氰胺用量分别为尿素与甲醛溶液总质量的1．0％和5％的条件下,合成的脲醛树脂胶粘剂的剪切强度为2．99MPa,游离甲醛的质量分数由传统工艺生产产品的0．6％～0．8％降低至0．063％,耐沸水时间为108min,且贮存稳定性好,达到了HJBZ-1998国家环境标志产品技术要求。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩，馏出液经铁炭氧微电解和混凝预处理，再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下，处理后出水pH6～9，COD 302mg／L，BOD5 108mg／L，SS30mg／L，色度36倍，水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.