新型硫酸铝-壳聚糖助滤剂强化砂滤效能研究

将硫酸铝和壳聚糖复配作为微絮凝助滤剂（AS-CTS）,考察其强化过滤性能.利用分子量分级、荧光光谱等手段分析有机物的去除特性,通过Zeta电位、絮体粒径、分形维数的变化分析其强化过滤机理.结果表明：AS-CTS较AS、CTS强化过滤效果明显,在AS/CTS复配比为2：1、CTS投加量0.3mg/L,转速300r/min,搅拌时间2min的条件下,砂滤出水浊度能达到0.1NTU、颗粒物125个/mL,残余铝浓度0.02mg/L;浊度和颗粒物去除率较未加AS-CTS分别提高了58%、61.7%.AS-CTS强化过滤可有效去除分子量>30KDa的腐殖酸和1~3KDa间的色氨酸类蛋白、溶解性微生物代谢产物、类富里酸.AS-CTS主要靠高分子吸附架桥作用和界面化学作用,增加胶体颗粒在滤料表面的粘附;通过形成较大粒径和分形维数的微絮体,增强絮体向滤料表面的迁移.     

混凝沉淀过程中铝系混凝剂的形态转化规律

研究了模拟配水中硫酸铝和氯化铝2种传统铝凝聚剂和2种聚合氯化铝(PAC)絮凝剂在混凝过程中的形态转化规律以及原水浊度和溶解性有机碳(DOC)对残余铝形态分布的影响.结果表明,在低浊体系中,投加铝系混凝剂是导致出水余铝升高的主要原因;但在高浊体系中,铝系混凝剂,尤其是聚合铝具有一定的除铝功能;混凝沉淀过程中传统铝凝聚剂的残余铝总量明显高于聚合铝混凝剂的残余铝总量;聚合铝混凝剂的残余铝全部为悬浮态铝,传统铝混凝剂的残余铝中还存在着胶体态铝和溶解态铝.原水浊度和DOC浓度增加,会提高残余铝中胶体态铝和溶解态铝的含量.     

低温高铁锰氨氮地下水两级生物净化快速启动

为了实现东北地区低温（5~6℃）高铁、锰、氨氮（TFe：9~15mg/L，Fe²⁺：6~12mg/L，NH₃-N：1.4~2.0mg/L，Mn²⁺：1.4~2.0mg/L）地下水的净化及解决同层净化中运行稳定性差、出水锰超标的问题，在水厂净化车间开展“两级曝气+两级过滤”工艺启动研究，采用差滤速和同滤速2种启动方式分别启动两级生物净化工艺.结果表明，2种启动方式分别在106，59d启动成功.同滤速启动可以有效的缩短两级生物净化的启动时间，铁、锰、氨氮去除负荷可达110.69，18.80，19.54g/（m²·h），沿程分析发现，铁在一级滤柱的60cm处即被去除至痕量；85.08%的氨氮在一级滤柱中去除，沿程各段去除均匀，14.92%的氨氮在二级滤柱中去除；锰的去除率和氧化活性去除区位受滤速及进水氨氮浓度影响较大，33.72%的锰在一级滤柱中去除，66.28%的锰在二级滤柱中去除，锰的去除仍然是滤池成熟的决定性因素.     

Study on the effects of organic matter characteristics on the residual aluminum and flocs in coagulation processes

Characteristics of organic matter may affect the residual aluminum after the coagulation process. This study reported the results of a survey for one drinking water treatment plant and measured the concentration of residual aluminum species with different molecular weights. Survey results indicated that humic acid or organic matter whose molecular weight was smaller than 1500 Da had significant effects on residual aluminum. All the treatment processes were ineffective in removing dissolved organic matter whose molecular weight was smaller than 1500 Da. These results also indicated that the addition of sand or polyacrylamide in the coagulation process could greatly decrease the concentration of humic acid, and the concentration of residual aluminum also decreased. These results revealed that for all water samples after filtration, the majority of total residual aluminum existed in the form of total dissolved aluminum, accounting for 70%–90%. The concentration of residual aluminum produced in bovine serum albumin solutions indicated that when the DOC was larger than 4.0 mg/L, there were still significant differences when the solution pH value varied from 4.0 to 9.0.     

Effects of advanced oxidation pretreatment on residual aluminum control in high humic acid water purification

Due to the formation of disinfection by-products and high concentrations of Al residue in drinking water purification, humic substances are a major component of organic matter in natural waters and have therefore received a great deal of attention in recent years. We investigated the effects of advanced oxidation pretreatment methods usually applied for removing dissolved organic matters on residual Al control. Results showed that the presence of humic acid increased residual Al concentration notably. With 15 mg/L of humic acid in raw water, the concentrations of soluble aluminum and total aluminum in the treated water were close to the quantity of Al addition. After increasing coagulant dosage from 12 to 120 mg/L, the total-Al in the treated water was controlled to below 0.2 mg/L. Purification systems with ozonation, chlorination, or potassium permanganate oxidation pretreatment units had little effects on residual Al control; while UV radiation decreased Al concentration notably. Combined with ozonation, the effects of UV radiation were enhanced. Optimal dosages were 0.5 mg O3/mg C and 3 hr for raw water with 15 mg/L of humic acid. Under UV light radiation, the combined forces or bonds that existed among humic acid molecules were destroyed; adsorption sites increased positively with radiation time, which promoted adsorption of humic acid onto polymeric aluminum and Al(OH)3(s). This work provides a new solution for humic acid coagulation and residual Al control for raw water with humic acid purification.     

铝盐混凝剂的混凝效果与残留铝含量和组分之间的关系研究

研究了氯化铝、硫酸铝、聚合氯化铝(poly-aluminum chloride, PAC)3种铝盐混凝剂在腐殖酸-高岭土模拟水样中的应用,以比较3种混凝剂在该水样中的混凝效果与残留铝含量和组分之间的关系.结果表明, 3种铝盐混凝剂在试验选取的投加量下对浊度和UV254的去除率最高可达90%左右,PAC能在较高的投加量下达到较好的混凝效果;较高投加量下PAC混凝沉淀出水中残留总铝含量为0.9 mg/L左右,余铝率为-3.0%左右,均明显低于传统的铝盐混凝剂;3种混凝剂混凝处理腐殖酸-高岭土模拟水样时,残留铝均大部分以溶解性总铝的形式存在,且溶解性有机铝在总溶解性铝中所占比例较大;PAC在腐殖酸-高岭土混凝沉淀出水中残留总铝的含量下降最快,且能够有效降低出水中毒性较大的溶解性铝的含量,其混凝沉淀出水中残留总溶解性铝含量为0.6 mg/L左右.     

Factors effecting aluminum speciation in drinking water be laboratory research

Effects of aluminum on water distribution system and human health mainly attribute to its speciation in drinking water. Laboratory experiments were performed to investigate factors that may influence aluminum speciation in water supply system. The concentration of soluble aluminum and its transformation among other aluminum species were mainly controlled by kinetics processes of related reactions. Total aluminum concentration had a notable effect on the concentrations of mononuclear and soluble aluminum in the first 4 day; while, when the reaction time was above 4 day, its effect became weak. At pH above 7.50, both fluoride and orthophosphate had little effect on aluminum speciation; while, when the solution pH was below 7.50, the concentrations of mononuclear and soluble aluminum were proportional to the concentration of fluoride and inversely proportional to the concentration of orthophosphate. Both mononuclear and polynuclear silicic acids could complex with mononuclear aluminum by forming soluble aluminosilicates. In addition, the adding sequence of orthophosphate and aluminum into drinking water would also affect the distribution of aluminum species in the first 4 day. In order to minimize aluminum bioavailability in drinking water, it was suggested that orthophosphate should be added prior to coagulant process, and that the concentrations of fluoride and silicic acids be controlled below 2.0 and 25 mg/L, respectively, prior to the treatment. The solution pH in coagulation and filtration processes should be controlled in the range of 6.50-7.50.     

混凝/微滤工艺用于青草沙水源水厂的生产废水回用研究

本文通过混凝/微滤工艺对青草沙水源水水厂的生产废水开展了回用处理研究,分析了常规污染物、微量有机物、金属离子的去除规律和消毒副产物生成趋势.结果表明,混凝预处理可以有效减缓膜污染;组合工艺对悬浮态物质如颗粒物、细菌、大肠杆菌等有较好的去除效果,去除率均达85%以上;对溶解性成分,尤其是Al和微量有机物去除效果不佳,去除率均低于20%.生产废水膜过滤后相同的消毒剂浓度时消毒副产物的生成趋势高于砂滤池和炭滤池出水.研究认为,青草沙水源水厂的生产废水净化后回用的最佳回用点是砂滤池前或活性炭生物滤池前.     

城市污水深度处理中有机物的去除

以城市污水地下水回灌为回用目的 ,研究不同的污水深度处理工艺及对二级生物处理出水中有机物的去除 .研究结果表明 ,原水若未经深度处理 ,直接由土壤含水层处理的出水不能满足推荐的回灌水水质要求 .对原水分别采用混凝沉淀、过滤、臭氧氧化、粉末活性炭和粒状活性炭吸附等处理单元及组合工艺进行深度处理效果的对比 ,最终选用由混凝沉淀 ,砂滤 ,粒状活性炭过滤与土壤含水层处理相结合的工艺流程 .城市污水处理厂的二级出水经该工艺处理后 ,出水中的 DOC可降至 3mg/L以下 ,且活性炭柱的产水床体积可达 350 0 BV.     

含铁、锰水源水深度处理工艺的运行实验研究

对铁、锰含量较高又存在有机微污染的原水进行深度处理的生产规模的净水厂（规模10m^3/h），进行了运行效能的试验研究。该水厂由射流曝气→砂滤罐→臭氧接触氧化罐→生物活性炭滤罐→木鱼石滤罐→紫外线照射清水箱等处理单元组成。通过曝气充氧－砂滤预处理，去除溶解性的二价铁60％以上,关剩余臭氧的量为0.4mg/L（相应的臭氧投量为：4mg/L)的条件下，经臭氧接触氧化和生物活性炭过滤，在HRT20min时，可去除铁锰高达100％，CODMn的去除率达90%左右。     

Spatial variations of aluminum species in drinking water supplies in Xi’an studied applying geographic information system

This article aimed to investigate the variation of aluminum species and the effects of coagulant type and water quality on aluminum speciation in drinking water.Statistical analysis showed that the concentration of total aluminum(AlT) of drinking water in Xi'an ranged from 0.051 to 0.417 mg/L and the concentration of AlT in about 24.7% studied samples was higher than the currently recommended value(0.2 mg/L).The areas fed by surface water plants had a larger portion(39.4%) of samples over the recommended value.In drinking water treated by alum coagulant,the average concentration of monomeric aluminum(Ala) was higher than that in water treated by poly aluminum chlorine(PACl) and poly aluminum ferric chloride(PAFC).The average concentrations of polynuclear aluminum(Alb) and colloidal/suspended aluminum(Alc) in the drinking water treated by alum were lower than those in water treated by PACl and PAFC.There was a notable decrease in AlT along with the delivery pipeline away from the plants,with an average decline of about 36 μg/(L·km).Besides coagulant type,water quality also could afflect aluminum speciation.In drinking water without orthophosphate,the concentrations of Ala and AlT were positively correlated with pH;while,in drinking water with orthophosphate,the concentrations of Ala and AlT were negatively correlated with pH.The addition of orthophosphate salts in the drinking water treatment process would be an effective method for aluminum control in pH range 6.5-8.2.     

Effects of fulvic acid and humic acid on aluminum speciation in drinking water

This article focused on the influences of fulvic acid and humic acid on aluminum speciation in drinking water. Factors including the concentration of residual chlorine and pH value had been concerned. Aluminum species investigated in the experiments included inorganic mononuclear, organic mononuclear, mononuclear, polymer, soluble, and suspended forms. It was found that the e ects of fulvic acid and humic acid on aluminum speciation depended mainly on their molecular weight. Fulvic acid with molecular weight less than 5000 Dalton had little influence on aluminum speciation; while fulvic acid with molecular weight larger than 5000 Dalton and humic acid would increase the concentration of soluble aluminum significantly even at concentration below 0.5 mg/L (calculated as TOC). Aluminum species, in the present of fulvic acid with molecular weight larger than 5000 Dalton and humic acid, were more stable than that in the present of fluvic acid with molecular mass less than 5000 Dalton, and varied little with reaction time. Within pH range 6.5–7.5, soluble aluminum increased notably in water with organic matter. As the concentration of residual chlorine increased, the e ects of fulvic acid and humic acid became weak. The reactions between humic acid, fulvic acid with large molecular weight, and aluminum were considered to be a multi-dentate coordination process. With the consideration of aluminum bioavailability, reducing the concentration of fulvic acid and humic acid and keeping the pH value among 6.5–7.5 were recommended during drinking water treatment.     

矿井水中氟化物及放射性核素去除研究

对淮北芦岭矿区饮用水源中氟化物及放射性核素去除工艺与机理进行了探讨,试验证明以聚合铝作混凝剂的混凝沉淀方法对去除氟化物及放射性核素非常有效,当PAC用量为20mg/L时,饮水中氟化物含量由1.85mg/L降至0.78mg/L?总α由0.13Bq/L降至0.03Bq/L?总β由0.26Bq/L降至0.18Bq/L?      

凹凸棒复合滤料生物过滤去除Fe2＋性能研究

利用凹凸棒复合滤料良好的吸附和生物挂膜性能对普通滤池进行生物强化,研究生物过滤对原水中Fe2＋的去除效果及影响因素。实验结果表明：原水溶解氧在3 mg/L左右,Fe2＋的去除率达到90%以上;温度在13.9℃-22.3℃时,Fe2＋去除率达到93%以上;滤速越低,生物过滤对Fe2＋的去除率越高,4 m/h为本实验研究的最佳水力负荷;原水中Fe2＋浓度在2 mg/L以下时,出水的Fe2＋浓度可以达到0.15 mg/L以下。反冲洗对生物过滤去除Fe2＋的影响较小,去除率在冲洗2 h后能够恢复到冲洗前的水平。     

混凝剂活性污泥法处理城市污水研究

采用混凝剂硫酸铝和氯化铁,研究了混凝剂活性污泥法的长期除磷效果,对两种混凝剂除磷性能进行了比较。研究表明,在混凝剂活性污泥法中,硫酸铝的稳定投药量为80 mg/L,与生物不具协同作用;氯化铁的稳定投药量为50 mg/L,与生物具有协同作用。在活性污泥反应器中,氯化铁的除磷性能好于硫酸铝。硫酸铝和氯化铁混凝剂不仅没有明显影响生物脱氮效果,而且能提高有机物的去除效果。     

Treatment of tannery wastewater by electrocoagulation

Treatment of tannery wastewater by electrocoagulation with low cell current(≤1A)and soluble electrodes(mild steel electrodes and aluminum electrodes)was studied.Compared with aluminum electrodes,mild steel electrodes were more effective for the removal of sulfide,with a removal efficiency of over 90%.But during the treatment process,black color precipitate typical to iron(Ⅱ)sulfides was produced.While aluminum electrodes were effective to eliminate the colority of the effluent,the removal efficiency of sulfide was lower than 12%.The mechanisms of the removal of chemical oxygen demand,ammonia,total organic carbon,sulfide and colority with the two soluble electrodes(mild steel and aluminum electrodes)were discussed in detail.In order to exert the predominance of diffenent types of electrodes,the tannery wastewater was treated using mild steel electrodes first followed by the filter and finally by the aluminum electrodes,the elimination rates of chemical oxygen demand,ammonia,total organic carbon,sulfide and colority were 68.0%,43.1%,55.1%,96.7% and 84.3%,respectively,with the initial concentrations 2413.1 mg/L,223.4 mg/L,1000.4 mg/L,112.3 mg/L and 256 dilution times,respectively.The absorbance spectra and energy consumption during electrocoagulation process were also discussed.     

混凝-膜过滤中滤饼层对双酚A的去除强化作用研究

以聚合氯化铝(PAC)和氯化铁(FeCl3)为混凝剂,分析了双酚A(BPA)在1g/L高岭土溶液混凝过程中的特征.并借助循环错流过滤强化污染层累积的方法,评价产生滤饼层的微滤(MF)膜对BPA的截留效果.结果表明:清洁的微滤膜过滤BPA溶液在短时间内达到截留吸附饱和,之后其对BPA的吸附截留作用显著降低;混凝絮体混合液经膜过滤时产生的污染层有利于BPA的去除,且单独混凝对BPA去除率最高的混凝剂投加量下进行膜过滤时的阻力较小.PAC混凝—膜过滤后BPA去除率比单独混凝提高了34.30%;FeCl3混凝—膜过滤后BPA去除率比单独混凝提高了28.38%.初始BPA浓度对混凝-膜过滤去除率有一定影响,BPA浓度为100μg/L时,比BPA浓度为5mg/L时采用2种混凝-微滤膜过滤方式去除率均有提高.     

接触过滤氧化法处理模拟含铁灰岩水的试验研究

为了解决煤矿灰岩水铁含量高,较难复用的问题,进行了接触过滤氧化法处理模拟含铁原水的试验研究。结果表明:采用石英砂滤料的接触过滤氧化工艺处理铁含量为2.0mg/L的模拟原水除铁效果明显,当气水比为2.0,pH值为7.5~8.0,停留时间小于2~3min,滤速为12.0m/h时,除铁率可达90%以上,滤后水满足铁含量0.3mg/L的井下复用水质要求,且过滤周期长达36h;同时分析得出最大平均催化氧化速率系数为KFe2+=1.50×1011L3mg-3s-1和除铁拟合曲线方程-Ln(Ct/Co)=-0.0011x2+0.0517x+1.748。     

石榴石滤料的过滤性能及反冲洗试验研究

石榴石作为一种新型矿物滤料在净水处理方面具有强大的竞争力和广阔的应用前景.通过对石榴石滤料进行过滤及反冲洗试验,研究其截污除浊性能、水头损失变化规律及对有机物的去除效果,并与传统的石英砂滤料做对比,同时探讨了石榴石滤料的适宜反冲洗强度范围及气水反冲洗运行参数.结果表明:在滤速为8 m/h的条件下,与石英砂滤柱的过滤效果相比,石榴石滤柱滤后水的平均浊度下降0.3 NTU,有机物平均质量分数下降5%,但其平均水头损失增长率为1 cm/h;在截污除浊及去除有机物方面,石榴石滤柱在60 cm滤层厚度处与石英砂滤柱在85 cm滤层厚度的去除效果十分接近,因此其能有效减少滤料体积,从而节省滤料及节约设备投资.在不同滤速下,水头损失是限制石榴石滤柱过滤周期的主要因素;石榴石滤料适宜的气反冲洗强度范围为14~16 L/（s·m2）,水反冲洗强度范围为5~7 L/（s·m2）,其气水反冲洗的最佳运行参数为气洗强度16 L/（s·m2）、水洗强度7 L/（s·m2）、气水联合反冲洗4 min、单独水漂洗7 min.其中,气反冲洗强度对石榴石滤料的反冲洗效果影响最大.研究显示,相较于传统石英砂滤料,石榴石滤料具有高过滤性能、低滤料体积的特点,在水处理滤料的应用方面显示出一定的优势.      

涤纶高弹丝纤维球滤料过滤特性研究

采用自主研制的涤纶高弹丝纤维球滤料对景观水进行过滤试验,研究其过滤特性及相关因素对过滤性能的影响. 结果表明,在不投加任何絮凝剂,滤速为30 m/h,平均进水浊度为87.5 NTU时,纤维球滤料过滤周期达16.5 h左右,出水浊度维持在3～5 NTU.当PAFC投加量为12 mg/L,滤速为30～50 m/h,进水浊度为50～70 NTU时,过滤出水浊度可以维持在1 NTU以下,过滤周期达6 h以上,周期截污量为30～45 kg/m3. 采用气冲－气水联合反冲－水冲的反冲洗方式,当气冲强度为25 L/(s·m2),水冲强度为8 L/(s·m2)时,纤维球滤料积泥量约占滤料质量的4.53%.