活性黑KN-B染料模拟废水电化学脱色

为进一步明确活性染料在可溶性阳极电化学体系中的脱色机理，以铝为牺牲阳极，不锈钢为阴极，在恒电流操作模式下，针对活性黑KN-B模拟废水，考察了电流密度、初始pH值、电解质种类及浓度、温度、染料浓度因素对染料脱色过程的影响。结果表明：(1)电流密度、电解液初始pH值、氯化钠电解质浓度、温度、染料浓度对染料溶液脱色效率影响显著，在一定实验条件下，染料溶液脱色率可达到88%；(2) 在不同pH的范围内，活性黑KN-B表现的脱色机理不同，pH 4～9为混凝与阴极还原脱色共同作用；pH＜4和＞9则表现为阴极还原脱色为主； (3) 氯化钠的加入在增强染料脱色的同时，也有助于芳环类物质的后续混凝去除。     

铁阳极电凝聚处理活性黑KN-B染料废水

对铁阳极电凝聚处理活性黑KN-B染料废水过程进行了实验研究.考察了电流密度、染料溶液初始pH值、电介质浓度及种类、温度、染料浓度等因素对脱色效率的影响.结果表明,在一定实验条件下,活性黑KN-B模拟废水的脱色效率达93%;电流强度、染料浓度、电解液初始pH值及电解质的种类对染料溶液脱色效率影响显著,电解液温度、电解质的浓度对脱色效率的影响不明显;以铁为阳极的原位电凝聚处理活性黑KN-B模拟废水混凝过程中主要作用机理以吸附电性中和为主;电凝聚过程中活性黑KN-B在阴极上发生了还原反应.     

活性艳蓝KN-R在ACF电极上成对电解脱色的影响因素

分别以活性炭纤维(ACF)为阳极和阴极，在无隔膜电解槽中研究了利用成对电解降解蒽醌染料活性艳蓝KN-R脱色过程的影响因素。考察了染料初始浓度、支持电解质Na₂SO₄、pH及温度诸条件对脱色性能的作用。结果表明：适当增加染料初始浓度和支持电解质浓度，酸性和中性条件以及适中的温度均对成对电解脱色性能有利。当染料初始浓度为251 mg/L，在合适的处理条件下，脱色率达到95%，脱除单位质量染料电耗仅为1.22 kWh/kg染料。     

ACF电极电解处理含NaCl结晶紫染料废水的研究

以吸附结晶紫达到饱和的活性炭纤维为阳极,在NaCl介质中对初始浓度为100 mg/L的结晶紫染料废水进行了电解脱色处理。实验考察了NaCl浓度、pH值和电流密度等对溶液脱色率的影响,测定了电解时溶液中生成的游离氯浓度及不同电解时间后溶液的紫外-可见吸收光谱曲线,并对不同电解时间后溶液的归一化吸光度比值进行了计算。结果发现,溶液中所产生的游离氯的浓度随电解时间的增加快速上升,20 min时就几乎达到了最大值;在活性氯的作用下,结晶紫分子中的大π共轭体系被破坏,溶液迅速脱色;电解液中所含的NaCl浓度、电解液的pH值和电流密度等都对脱色率有影响;在一定实验条件下,初始浓度为100 mg/L的结晶紫染料废水在电解60 min后脱色率可高达99.3%。     

双转盘反应器光催化处理罗丹明B

采用溶胶—凝胶法制备的TiO2/Ti电极为光阳极,Cu、Fe、Zn或C为阴极,组成双转盘反应器,以罗丹明B(RhB)为目标污染物,考察了反应条件对光催化效率的影响.结果表明,最佳反应条件:阴极材料为Cu;转盘转速为70 r/min;初始pH为2.5；Na2SO4质量浓度为1.0 g/L; RhB初始质量浓度为20 mg/L.在最佳反应条件下,处理RhB模拟废水30 min的脱色率可达到99.9％.双转盘反应器处理不同浓度的RhB时,其脱色率是单转盘的1.12～2.33倍,且倍数随着RhB浓度增大而增加,表明双转盘反应器可高效地光催化处理高浓度染料废水.     

软锰矿电化学协同作用对活性嫩黄模拟废水脱色率的研究

以活性嫩黄K 4G模拟废水为处理对象 ,采用软锰矿与电化学协同法 ,分别在不同软锰矿加入量、电流密度、pH值、电解时间、染料初始浓度条件下进行电解实验 ,考察了各种因素对脱色率的影响。结果表明 ,增加软锰矿的用量、增大电流密度、降低pH值、延长电解时间都能提高脱色率 ,染料初始浓度对脱色率影响不显著。溶液中溶解态锰的浓度的变化表明 ,Mn(II)在处理过程中表现出催化作用 ,外加电压可强化软锰矿的氧化作用     

粉煤灰负载铁离子催化氧化活性黄染料废水

以粉煤灰为载体,制备铁/粉煤灰负载型催化剂,并利用该催化剂催化H2O2氧化降解活性黄染料废水,探讨了H2O2投加量、催化剂投加量、染料初始浓度和初始pH值等因素对染料废水COD去除率和脱色率的影响。结果表明,当染料废水COD初始浓度为200 mg/L,初始pH值为1.7,投加0.5 g/100 mL催化剂及加入1.0 mL浓度为1.13 mol/L的H2O2溶液时,处理效果最好,此时染料废水的COD去除率和脱色率分别达到63%和99%,并且废水的可生化性得到很大的提高。利用该负载催化剂能够有效地减少活性黄染料废水中Fe3+的残留量。     

软锰矿电化学协同作用对活性嫩黄模拟废水脱色率的研究

以活性嫩黄K-4G模拟废水为处理对象，采用软锰矿与电化学协同法，分别在不同软锰矿加入量、电流密度、pH值、电解时间、染料初始浓度条件下进行电解实验，考察了各种因素对脱色率的影响。结果表明，增加软锰矿的用量、增大电流密度、降低pH值、延长电解时间都能提高脱色率，染料初始浓度对脱色率影响不显著。溶液中溶解态锰的浓度的变化表明，Mn(Ⅱ)在处理过程中表现出催化作用，外加电压可强化软锰矿的氧化作用。     

钢渣对直接大红4BE染料的脱色性能

采用搅拌吸附的方法,在混凝搅拌装置中考察了钢渣对直接大红4BE染料废水脱色率的影响因素及其机理。结果表明,当初始pH值为7.0、染料初始浓度为100 mg/L、钢渣目数为100～120目、用量为10.0 g时,按染料与钢渣的质量比2∶1（mg/g）、转速为200 r/min搅拌吸附,脱色效果较好。当反应时间为100 min时,脱色率为97.14%,可达纺织染整工业水污染物排放标准中色度的Ⅰ类标准。吸附过程的机理主要有快速的物理吸附、OH-与带色素的阴离子之间的配位体交换及絮凝沉淀作用。     

活性炭纤维电极对TAIC的电催化氧化

以活性炭纤维为阳极,不锈钢电极为阴极,研究了活性炭纤维电极电催化氧化去除水中三烯丙基异氰脲酸酯(TAIC)的方法.采用单因素实验法研究pH,电流密度,电解质种类和浓度对电催化氧化性能的影响,并找到最佳反应条件.实验结果表明,在TAIC模拟废水中,TAIC初始浓度为150 mg/L,pH为7,电流密度为50 mA/cm2,以0.06 mol/LNa2SO4为电解质溶液时反应效果最佳,60 min时TAIC的去除率为90.7％.     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Radionuclides and trace elements in fish collected upstream and downstream of Los Alamos national laboratory and the doses to humans from the consumption of muscle and bone

Abstract

The purpose of this study was to determine radionuclide and trace element concentrations in bottom‐feeding fish (catfish, carp, and suckers) collected from the confluences of some of the major canyons that cross Los Alamos National Laboratory (LANL) lands with the Rio Grande (RG) and the potential radiological doses from the ingestion of these fish. Samples of muscle and bone (and viscera in some cases) were analyzed for ³H, ⁹⁰Sr, ¹³⁷Cs, ^totU, ²³⁸Pu, ^239,240Pu, and ²⁴¹Am and Ag, As, Ba, Be, Cr, Cd, Cu, Hg, Ni, Pb, Sb, Se, and Tl. Most radionuclides, with the exception of ⁹⁰Sr, in the muscle plus bone portions of fish collected from LANL canyons/RG were not significantly (p<0.05) higher from fish collected upstream (San Ildefonso/background) of LANL. Strontium‐90 in fish muscle plus bone tissue significantly (p<0.05) increases in concentration starting from Los Alamos Canyon, the most upstream confluence (fish contained 3.4E‐02 pCi g^‐1 [126E‐02 Bq kg^‐1]), to Frijoles Canyon, the most downstream confluence (fish contained 14E‐02 pCi g^‐1 [518E‐02 Bq kg^‐1]). The differences in ⁹⁰Sr concentrations in fish collected downstream and upstream (background) of LANL, however, were very small. Based on the average concentrations (±2SD) of radionuclides in fish tissue from the four LANL confluences, the committed effective dose equivalent from the ingestion of 46 lb (21 kg) (maximum ingestion rate per person per year) of fish muscle plus bone, after the subtraction of background, was 0.1 ± 0.1 mrem y^‐1 (1.0 ± 1.0 μSv y^‐1), and was far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem y^‐1 (1000 μSv y^‐1). Of the trace elements that were found above the limits of detection (Ba, Cu, and Hg) in fish muscle collected from the confluences of canyons that cross LANL and the RG, none were in significantly higher (p<0.05) concentrations than in muscle of fish collected from background locations.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Patterns of volatile metabolites and nonvolatile trichothecenes produced by isolates of <Emphasis Type="Italic">Stachybotrys,Fusarium, Trichoderma,Trichothecium</Emphasis> and <Emphasis Type="Italic">Memnoniella</Emphasis>

We reported previously that trichodiene, a volatile trichothecene derivative, was produced by a Stachybotrys isolate, also known to produce highly cytotoxic, non-volatile, macrocyclic trichothecenes (satrotoxins). We investigated the relationship between the production of trichodiene and various non-volatile trichothecenes for several molds. Volatile metabolites were concentrated by adsorption on Tenax TA and analyzed by GC/MS, while non-volatile metabolites were separated by HPLC, derivatized and analyzed by GC/MS. Stachybotrys chartarum isolates producing macrocyclic trichothecenes secreted significantly larger amounts of trichodiene and other sesquiterpenes than isolates which only produced simple trichothecenes. The amounts of secreted trichodiene were relatively small in all cases. With the exception of Memnoniella, which excreted small amounts of sesquiterpenes, the other isolates produced varying amounts of sesquiterpenes, including trichodiene, as well as simple tricothecenes, no detectable trichodiene, but large amounts of griseofulvin derivatives. In Stachybotrys there is apparently a correlation between trichodiene and macrocyclic trichothecene production. In the remaining isolates, there was no simple relationship between trichodiene and non-volatile trichothecene synthesis. Trichodiene is produced in larger amounts by Stachybotrys isolates, which also produce satratoxins, but it will be difficult to utilize this metabolite to detect toxic isolates in buildings due to the relatively small amounts excreted.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

Radionuclides in deer and elk from Los Alamos national laboratory and the doses to humans from the ingestion of muscle and bone

Abstract

This paper summarizes radionuclide concentrations (³H, ⁹⁰Sr, ¹³⁷Cs, ²³⁸Pu, ^239,240Pu, ²⁴¹Am, and ^totU) in muscle and bone tissue of mule deer (Odocoileus hemionus) and Rocky Mountain elk (Cervus elaphus) collected from Los Alamos National Laboratory (LANL), Los Alamos, New Mexico, lands from 1991 through 1998. Also, the committed effective dose equivalent (CEDE) and the risk of excess cancer fatalities (RECF) to people who ingest muscle and bone from deer and elk collected from LANL lands were estimated. Most radionuclide concentrations in muscle and bone from individual deer (n = 11) and elk (n = 22) collected from LANL lands were either at less than detectable quantities (where the analytical result was smaller than two counting uncertainties) and/or within upper (95%) level background (BG) concentrations. As a group, most radionuclides in muscle and bone of deer and elk from LANL lands were not significantly higher (p<0.10) than in similar tissues from deer (n = 3) and elk (n = 7) collected from BG locations. Also, elk that had been radio collared and tracked for two years and spent an average time of 50% on LANL lands were not significantly different in most radionuclides from road kill elk that have been collected as part of the environmental surveillance program. Overall, the upper (95%) level net CEDEs (the CEDE plus two sigma for each radioisotope minus background) at the most conservative ingestion rate (50 lbs of muscle and 13 lbs of bone) were as follows: deer muscle = 0.22 mrem y^‐1 (2.2 μSv y^‐1), deer bone = 3.8 mrem y^‐1 (38 μSv y^‐1), elk muscle = 0.12 mrem y^‐1 (1.2 μSv y^‐1), and elk bone = 1.7 mrem y^‐1 (17 μSv y^‐1). All CEDEs were far below the International Commission on Radiological Protection guideline of 100 mrem y^‐1 (1000 μSv y^‐1), and the highest muscle plus bone net CEDE corresponded to a RECF of 2E‐06, which is far below the Environmental Protection Agency upper level guideline of 1E‐04.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.