The sorption of Zectran on bottom sediments and peat moss

Abstract

A modified analytical method employed to determine the insecticide Zectran in natural waters frequently has resulted in erroneous data. The errors have been attributed to interferences from particulate matter in these waters. In order to evaluate analytical interferences due to sorption of Zectran on particu‐lates, a series of experiments was performed using bottom sediments and a peat moss in contact with aqueous solutions of Zectran at a pH value of 6.0 and 20°C.

Isotherm studies confirmed that Zectran sorption occurs in a direct relation to the amount of chemically oxidizable carbon present in the bottom sediments or peat moss. However, the extent of sorption was limited, which suggested that particulates may not be the primary interference in the modified analytical method.     

Effect of overlying water pH, dissolved oxygen, salinity and sediment disturbances on metal release and sequestration from metal contaminated marine sediments

Experiments were undertaken to examine the key variables affecting metal release and sequestration processes in marine sediments with metal concentrations in sediments reaching up to 86, 240, 700, and 3000 mg kg(-1) (dry weight) for Cd, Cu, Pb and Zn, respectively. The metal release and sequestration rates were affected to a much greater extent by changes in overlying water pH (5.5-8.0) and sediment disturbance (by physical mixing) than by changes in dissolved oxygen concentration (3-8 mg l(-1)) or salinity (15-45 practical salinity units). The physical disturbance of sediments was also found to release metals more rapidly than biological disturbance (bioturbation). The rate of oxidative precipitation of released iron and manganese increased as pH decreased and appeared to greatly influence the sequestration rate of released lead and zinc. Released metals were sequestered less rapidly in waters with lower dissolved oxygen concentrations. Sediments bioturbated by the benthic bivalve Tellina deltoidalis caused metal release from the pore waters and higher concentrations of iron and manganese in overlying waters than non-bioturbated sediments. During 21-day sediment exposures, T. deltoidalis accumulated significantly higher tissue concentrations of cadmium, lead and zinc from the metal contaminated sediments compared to controls. This study suggests that despite the fact that lead and zinc were most likely bound as sulfide phases in deeper sediments, the metals maintain their bioavailability because of the continued cycling between pore waters and surface sediments due to physical mixing and bioturbation.     

Color and COD removal from wastewater containing Reactive Black 5 using Fenton's oxidation process

In this study, Reactive Black 5 (RB5) was removed from synthetic wastewater using Fenton's oxidation (FO) process. Experiments were conducted on the samples containing 100 and 200 mg l(-1) of RB5 to remove the dye toxicity. Seventy-five milligram per litre of RB5 caused 25% toxicity on 24-h born daphnids whereas 100 mg l(-1) of RB5 displayed 100% toxicity on Daphnia magna. The study was performed in a systematic approach searching optimum values of FeSO(4) and H(2)O(2) concentrations, pH and temperature. Optimum pH and temperature for 100 mg l(-1) of RB5 were observed as 3.0 and 40 degrees C, respectively, using 100 mg l(-1) of FeSO(4) and 400 mg l(-1) of H(2)O(2) resulted in 71% chemical oxygen demand (COD) and 99% color removal. For 200 mg l(-1) of RB5, 84% COD removal was obtained using 225 mg l(-1) of FeSO(4) and 1000 mg l(-1) of H(2)O(2) yielding 0.05 molar ratio at pH 3.0 and 40 degrees C. Color removal was also more than 99%. The optimum conditions determined in accordance with the literature data. The H(2)O(2) requirement seems to be related to initial COD of the sample. FeSO(4)/H(2)O(2) ratios found were not changed for both concentrations. The temperature affected the COD removal significantly at high degrees. Toxicity was completely removed for each concentration of RB5 at optimum removal conditions.     

Enhancement of PAH biomineralization rates by cyclodextrins under Fe(III)-reducing conditions

Amendment of a soil slurry with low concentrations of a cyclodextrin, hydroxypropyl-beta-cyclodextrin (HPCD), (0.05-0.5 g l(-1)) increased the phenanthrene mineralization rate of a microbial consortium by 25% under Fe(III)-reducing conditions. Although a higher concentration (5.0 g l(-1)) resulted in a faster initial rate of mineralization, mineralization ceased after 25 days with maximum mineralization 17% lower than the control (no HPCD). At lower HPCD concentrations, mineralization was still taking place at day 76. Although pH should affect Fe(III) solubility, mineralization rates at pH 6.0 and 8.0 were comparable. Decreasing the temperature reduced the extent and rate of mineralization, but mineralization rates at 10 degrees C were still 60% of that obtained at 30 degrees C.     

Zinc toxicity in the fish Cnesterodon decemmaculatus in the Paraná River and Río de La Plata Estuary

Acute static tests were performed to assess Zn toxicity on adults of Cnesterodon decemmaculatus (not sexed), a neotropical fish of wide distribution in the Río de la Plata basin. Tests were carried out with ZnCl2 dissolved in natural waters from the Lower Paraná River, the Río de la Plata Estuary, reconstituted waters of similar composition, tap and distilled waters. Median lethal concentration at 24 h was positively correlated to conductivity and the concentrations of Ca2+, Mg2+, and HCO3- (r=0.99, 0.96, 0.97, 0.99, p<0.05, respectively), being higher at the Río de la Plata Estuary (61.2 mg l(-1)) than at the Lower Paraná River (35.3 mg l(-1)). Contaminant load in the natural waters tested was similar at both sites, being Zn concentration 40 and 44 microg l(-1), respectively. An assay with reconstituted water of similar alkalinity to the estuary showed a simultaneous decrease in HCO3- and dissolved Zn, while the Zn speciation, predicted with a computer program, suggested that Zn2+ precipitated as ZnCO3. The effect of Ca2+ on Zn toxicity is also discussed. Zn toxicity was higher in the Río de la Plata Estuary water than in synthetic water of similar ionic composition (24-h LC50 = 93.2 mg l(-1)), suggesting the synergistic effect of other toxic pollutants such as metals, present in the former which were absent in the later.     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

Chlorination of bisphenol A: kinetics and by-products formation

The kinetics of initial chlorination of bisphenol A (BPA) was studied between pH 2 and 11 at room temperature (20 +/- 2 degrees C). pH Profile of the apparent second-order rate constant of the reaction of BPA with chlorine were modeled considering the elementary reactions of HOCl with BPA species and an acid-catalyzed reaction. The predominant reactions at near neutral pH were the reactions of HOCl with the two phenolate species of BPA (k = 3.10 x 10(4) M(-1)s(-1) for BPA- and 6.62 x 10(4) M(-1) s(-1) for BPA(2-)). At near neutral pH, half-life times of BPA were calculated to be less than 1.5 h for chlorine residual higher than 0.2 mg l(-1). Chlorination of synthetic treated waters spiked with BPA showed that BPA disappeared within 4 h and that chlorinated bisphenol A congeners were rapidly formed and remained in solution for up to 10-20 h when low chlorine dosages are applied (0.5-1 mg l(-1)). To limit their presence in drinking water networks, it is then necessary to maintain high chlorine residuals that rapidly produce and decompose chlorinated bisphenol A congeners.     

Metals in bulk deposition and surface waters at two upland locations in northern England

Concentrations of aluminium and minor metals (Mn, Ni, Cu, Zn, Sr, Cd, Ba, Pb) were measured in precipitation and surface water at two upland locations (Upper Duddon Valley, UDV; Great Dun Fell, GDF) in northern England for 1 year commencing April 1998. At both locations, the loads in bulk precipitation were at the lower ends of ranges reported for other rural and remote sites, for the period 1985-1995. The deposited metals were mostly in the dissolved form, and their concentrations tended to be greatest when rainfall volumes were low. The concentrations of Cu, Zn and Pb in deposition were correlated (r2 > or = 0.40) with concentrations of non-marine sulphate. Three streams, ranging in mean pH from 5.07 to 7.07, and with mean concentrations of dissolved organic carbon (DOC) < 1 mg l(-1). were monitored at UDV, and two pools (mean pH 4.89 and 6.83, mean DOC 22 and 15 mg l(-1)) at GDF. Aluminium and the minor metals were mainly in the dissolved form, and in the following ranges (means of 49-51 samples. microg l(-1)): Al 36-530. Mn 4.4-36, Ni 0.26-2.8, Cu 0.25-1.7, Zn 2.1-30, Cd 0.03-0.16, Ba 1.9-140, Pb 0.10-4.5. Concentrations were generally higher at GDF. Differences in metal concentrations between the two locations and between waters at each location, and temporal variations in individual waters, can be explained qualitatively in terms of sorption to solid-phase soil organic matter and mineral surfaces, complexation and transport by DOC, and chemical weathering. The UDV catchments are sinks for Pb and sources of Al, Mn, Sr, Cd and Ba. The GDF catchments are sources of Al, Mn, Ni, Zn, Sr, Cd and Ba. Other metals measured at the two locations are approximately in balance. Comparison of metal:silicon ratios in the surface waters with values for silicate rocks indicates enrichment of Ni and Cu, and substantial enrichment of Zn, Cd and Pb. These enrichments, together with high metal deposition in the past, make it likely that concentrations of the metals in the surface waters are governed by release from catchment pools of atmospherically-deposited metal. The catchments appear to be responding on a time scale of decades, possibly centuries, to changes in metal deposition. For the more acid waters at UDV, the calculated free-ion concentrations of Al are similar to published LC50 values for acute toxicity towards fish. The free-ion concentrations of Ni, Cu, Zn and Cd in all the surface waters are one-to-four orders of magnitude lower than reported LC50 values for fish.     

Comparative study on the susceptibility of freshwater species to copper-based pesticides

Copper compounds have been intentionally introduced into water bodies as aquatic plant herbicides, algicides and molluscicides. Copper-based fertilizers and fungicides have been widely used in agriculture as well. Despite the fact that copper is an essential element for all biota, elevated concentrations of this metal have been shown to affect a variety of aquatic organisms. Nonetheless, comparative studies on the susceptibility of different freshwater species to copper compounds have seldom been performed. This study was conducted to compare toxicity of copper-based pesticides (copper oxychloride, cuprous oxide and copper sulfate) to different freshwater target (Raphidocelis subcapitata, a planktonic alga and Biomphalaria glabrata, a snail) and non-target (Daphnia similis, a planktonic crustacean and Danio rerio, a fish) organisms. Test water parameters were as follows: pH = 7.4 +/- 0.1; hardness 44 +/- 1 mg/l as CaCO3; DO 8-9 mg/l at the beginning and > 4 mg/l at the end; temperature, fish and snails 25 +/- 1 degrees C, Daphnia 20 +/- 2 degrees C, algae 24 +/- 1 degrees C. D. similis (immobilization), 48-h EC50s (95% CLs) ranging from 0.013 (0.011-0.016) to 0.043 (0.033-0.057) mg Cu/l, and R. subcapitata (growth inhibition), 96-h IC50s from 0.071 (0.045-0.099) to 0.137 (0.090-0.174) mg Cu/l, were the most susceptible species. B. glabrata (lethality), 48-h LC50s from 0.179 (0.102-0.270) to 0.854 (0.553-1.457) mg Cu/l, and D. rerio (lethality), 48-h LC50s 0.063 (0.045-0.089), 0.192 (0.133-0.272) and 0.714 (0.494-1.016) mg Cu/l, were less susceptible than Daphnia to copper-based pesticides. Findings from the present study therefore suggest that increased levels of copper in water bodies is likely to adversely affect a variety of aquatic species.     

Fluoride removal performance of a novel Fe-Al-Ce trimetal oxide adsorbent

A trimetal oxide was developed as a fluoride adsorbent by coprecipitation of Fe(II), Al(III) and Ce(IV) salt solutions with a molar ratio of 1:4:1 under alkaline condition. The material retained amorphous structure and maintained relatively stable fluoride adsorption performance at calcination temperatures lower than 600 degrees C. The optimum pH range for fluoride adsorption was 6.0-6.5 and the adsorbent also showed high defluoridation ability around pH 5.5-7.0, which is preferable for actual application. A high fluoride adsorption capacity of 178 mg g(-1) was acquired under an equilibrium fluoride concentration of 84.5 mg l(-1), adsorbent dose of 150 mg l(-1) and pH 7.0. The adsorption isotherm could be better described by the two-site Langmuir model than the one-site model, suggesting the existence of two types of active sites on the adsorbent surface. Coexistence of high concentrations of phosphate or arsenate only led to partial inhibition of fluoride adsorption, which further suggests the existence of heterogeneous adsorption sites. Sulfate and chloride did not affect fluoride adsorption, and nitrate influenced it only when the concentration of NO(3)(-)-N exceeded 50 mg l(-1). A high desorption efficiency of 97% was achieved by treating fluoride loaded Fe-Al-Ce oxide with NaOH solution at pH 12.2. A column experiment using the adsorbent fabricated into 1mm pellets was performed at an initial fluoride concentration of 5.5 mg l(-1), space velocity of 5h(-1) and pH of 5.8, and 2240 bed volumes were treated with the effluent fluoride under 1.0 mg l(-1).     

Changes in microbiological metabolism under chemical stress

Chemical stress may alter microbiological metabolism and this, in turn, may affect the natural and engineered systems where these organisms function. The impact of chemical stress on microbiological metabolism was investigated using model chemicals 2,4-dinitrophenol (DNP), pentachlorophenol (PCP), and N-ethylmaleimide (NEM). Biological activity of Pseudomonas aeruginosa was measured in batch systems, with and without stressors at sub-lethal concentrations. Stressor DNP, between 49 and 140 mg l(-1), and PCP, at 15 and 38 mg l(-1), caused decreases in biomass growth yields, but did not inhibit substrate utilization rates. These effects increased with stressor concentrations, showing as much as a 10% yield reduction at the highest DNP concentration. This suggests that a portion of carbon and energy resources are diverted from growth and used in stress management and protection. Stressor DNP, between 300 and 700 mg l(-1), and PCP at 85 mg l(-1) caused decreases in growth yields and substrate utilization rates. This suggests an inhibition of both anabolism and catabolism. Stressor NEM was the most potent, inhibiting biological activity at concentrations as low as 2.7 mg l(-1). These findings will ultimately be useful in better monitoring and management of biological treatment operations and contaminated natural systems.     

Influence of pH on persulfate oxidation of TCE at ambient temperatures

In situ chemical oxidation (ISCO) is a technology used for groundwater remediation. This laboratory study investigated the use of the oxidant sodium persulfate for the chemical oxidation of trichloroethylene (TCE) at near ambient temperatures (10, 20 and 30 degrees C) to determine the influence of pH (pH=4, 7 and 9) on the reaction rate (i.e., pseudo-first-order rate constants) over the range of temperatures utilized. TCE solutions (60 mg l(-1); 0.46 mM) were prepared in phosphate buffered RO water and a fixed persulfate/TCE molar ratio of 50/1 was employed in all tests. Half-lives of TCE degradation at 10, 20 and 30 degrees C (pH 7) were 115.5, 35.0 and 5.5h, respectively. Maximum TCE degradation occurred at pH 7. Lowering system pH resulted in a greater decrease in TCE degradation rates than increasing system pH. Radical scavenging tests used to identify predominant radical species suggested that the sulfate radical (SO(4)(.-)) predominates under acidic conditions and the hydroxyl radical (.OH) predominates under basic conditions. In a side by side comparison of TCE degradation in a groundwater vs. unbuffered RO water it was demonstrated that when the system pH is buffered to near neutral pH conditions due to the presence of natural occurring groundwater constituents that the TCE degradation rate is higher than in unbuffered RO water where the system pH dropped from 5.9 to 2.8. The results of this study suggest that in a field application of ISCO, pH should be monitored and adjusted to near neutral if necessary.     

Primary biodegradation of veterinary antibiotics in aerobic and anaerobic surface water simulation systems

The primary aerobic and anaerobic biodegradability at intermediate concentrations (50-5000 microg/l) of the antibiotics olaquindox (OLA), metronidazole (MET), tylosin (TYL) and oxytetracycline (OTC) was studied in a simple shake flask system simulating the conditions in surface waters. The purpose of the study was to provide rate data for primary biodegradation in the scenario where antibiotics pollute surface waters as a result of run-off from arable land. The source of antibiotics may be application of manure as fertilizer or excreta of grazing animals. Assuming first-order degradation kinetics, ranges of half-lives for aerobic degradation of the four antibiotics studied were 4-8 days (OLA), 9.5-40 days (TYL), 14-104 days (MET) and 42-46 days (OTC). OLA and OTC were degraded with no initial lag phase whereas lag phases from 2 to 34 days (MET) and 31 to 40 days (TYL) were observed for other substances. The biodegradation behaviour was influenced by neither the concentrations of antibiotics nor the time of the year and location for sampling of surface water. Addition of 1 g/l of sediment or 3 mg/l of activated sludge from wastewater treatment increased the biodegradation potential which is believed to be the result of increased bacterial concentration in the test solution. Biodegradation was significantly slower in tests conducted in absence of oxygen. Assessments of the toxic properties of antibiotics by studying the influence on the biodegradation rates of 14C-aniline at different concentrations of antibiotics showed that no tests were conducted at toxic concentrations.     

Sulphate toxicity to the aquatic moss, Fontinalis antipyretica

The aquatic moss, Fontinalis antipyretica was exposed to elevated sulphate concentrations for 21-days. Gametophores were sectioned to 2 cm lengths and exposed to sulphate concentrations up to 1500 mg/l, in waters of different water hardness. Significant reductions in shoot length, dry weight, and chlorophyll a and b concentrations (per gram dry weight) were observed in soft water (19 mg/l as CaCO3); however, effects were significantly reduced in waters of increasing hardness (up to 105 mg/l as CaCO3). The substantial reduction of sulphate toxicity in waters of increasing hardness suggests water chemistry plays a significant role in affecting sulphate toxicity and should be considered when setting sulphate discharge limits.     

Aerosolization of an anionic surfactant (LAS) and dissolved organic carbon (DOC) under laboratory conditions.

Aerosolization of natural salt and brackish waters under laboratory conditions is responsible for the transfer of synthetic surfactants such as linear alkylbenzene sulphonate (LAS) from water to the atmosphere. Excluded the lagoon sample which stands apart, on the average ca. 45% of the LAS present at concentrations between 0.1 and 4.1 microg l(-1) in the tested coastal and offshore marine and lagoon waters was transferred to the aerosol extract. The distribution of the individual LAS homologs in the aerosol is very similar to that in water, which indicates no preferential removal from the bulk water of any LAS homolog. The fraction of dissolved organic carbon (DOC) undergoing aerosolization under the same conditions for each tested sample was on an average ca. 3.3%, corresponding to ca. 5.6 mg l(-1). On the average, the enrichment factor of the sea samples, resulting from the changing of the LAS/DOC ratio before and after aerosolization, was ca. 20.     

Characteristics of leachate from pyrolysis residue of sewage sludge

The pyrolysis residue (SP) of sewage sludge (SS) produced at 500 degrees C was subjected to batch and column leaching tests to investigate the release of its organic and inorganic constituents and metals. For comparison, incineration ash (SI) obtained from a SS incinerator was also tested. Pyrolysis and incineration reduced organic matter of SS from 0.78 kg kg(-1)-dry SS to 0.16 and 0.01 kg kg(-1)-dry SS, respectively. Heavy metals remained in SP without being volatilized, although Cd and Pb were transferred into the off-gas during incineration. In the batch leaching test with the leaching liquid-to-solid mass ratio (L/S)=10, the pH of the SS, SP, and SI filtrates was 6.3, 7.9, and 11.0, respectively. The total organic carbon concentrations were in the order SS (877 l mg l(-1))>SP (99 mg l(-1))>SI (26 mg l(-1)). The SP and SI filtrates met the landfill standard for the Cd and Pb concentrations (<0.3 mg l(-1)). In the column tests, although the SP contained more organic matter than that of SI, its carbon discharge into the leachate under aerobic conditions was similar to that of SI under anaerobic conditions. The leaching of heavy metals, such as Cd, Cr, Pb, and Zn, was also suppressed in SP during the active decomposition of organic matter. We demonstrated that pyrolysis reduces the potential release of pollutants from sewage sludge in landfill, making it a promising method of treating sewage sludge before landfilling.     

The spatial variability of nitrogen and phosphorus concentration in a sand aquifer influenced by onsite sewage treatment and disposal systems: a case study on St. George Island, Florida

Groundwater from a shallow freshwater lens on St. George Island, a barrier island located in the Panhandle of Florida, eventually discharges into Apalachicola Bay or the Gulf of Mexico. Nutrient concentrations in groundwaters were monitored downfield from three onsite sewage treatment and disposal systems (OSTDS) on the island. Estimates of natural groundwater nutrient concentrations were obtained from an adjacent uninhabited island. Silicate, which was significantly higher in the imported drinking water relative to the surficial aquifer on St. George Island (12.2+/-1.9 mg Si l(-1) and 2.9+/-0.2 mg Si l(-1), respectively), was used as a natural conservative tracer. Our observations showed that nitrogen concentrations were attenuated to a greater extent than that of phosphorus relative to the conservative tracer. At the current setback distance (23 m), both nitrogen and phosphate concentrations are still elevated above natural levels by as much as 2 and 7 times, respectively. Increasing the setback distance to 50 m and raising the drainfields 1 m above the ground surface could reduce nutrient levels to natural concentrations (1.1+/-0.1 mg N l(-1), 0.20+/-0.02 mg P l(-1)).     

Modeling the crystallization of magnesium ammonium phosphate for phosphorus recovery

The crystallization of magnesium ammonium phosphate (MAP) is one of the main processes for recovering P and N from wastewater. Chemically defined solution systems were designed; the saturation indices (SIs) of the solution systems with respect to MAP were derived by using a geochemical aqueous model Program, PHREEQC 2.11; the effects of the solution conditions were evaluated using thermodynamic theories. The concentrations of P and Mg in the tested solutions were 10-600 mg l(-1) and 24-720 mg l(-1), respectively, the molar ratios of N/P and pH values of the solutions varied in the ranges of 1-40 and 6.0-12.0, respectively. The temperature of all the tests was set at 25 degrees C. The test results show that the SI value of MAP is the logarithmic functions of the concentrations of P, ammonium-N and Mg, and increases with the increase of the concentration of each element. The SI value of MAP is a polynomial function of pH value of the solution, and the optimum pH value for the crystallization of MAP is 9.0 but increases slightly with the increase of the N/P. Moreover, the SI value of MAP is a power law function of the ionic strength of solutions but decreases with its increase. The adjustment of the Mg concentration and the control of solution pH are two effective methods for the control of the crystallization of MAP. The results obtained from the research can be used to guide the design and control of MAP crystallization process for the removal and recovery of P.     

Biodegradation of chemicals in a standardized test and in environmental conditions

The estimation of biodegradation rates is an important source of uncertainty in chemical risk assessment. The existing OECD tests for ready biodegradability have been developed to devise screening methods to determine whether a chemical is potentially easily biodegradable, rather than to predict the actual rate, of biodegradation in the environment. However, risk assessment needs degradation rates. In practice these rates are often estimated (default values) from ready biodegradability tests. These tests have many compromising arbitrary features compared to the situation in the real environment. One important difference is the concentration of the chemical. In wastewater treatment or in the environment many chemicals are present at ng l(-1) to microg l(-1) levels whereas in the tests the concentrations exceed 10-400 mg carbon per litre. These different concentrations of the chemical will lead to different growth kinetics and hence different biodegradation rates. At high concentrations the chemical, if it is degradable, can serve as a primary substrate and competent microorganisms will grow exponentially, resulting in a sigmoid biodegradation curve. At low environmental concentrations the chemical does not serve as a primary substrate, and therefore does not support significant growth of the degraders, and the substrate has a linear biodegradation rate. In this study the biodegradation rates of two reference chemicals, aniline and 4-chloroaniline, were compared in a standard method and in more realistic conditions at low concentrations, using 14C-labelled substances and different sources of inocula. Biomass evolution during the tests was monitored by adenosine triphosphate measurement and also on the basis of the residual 14C-activity in the particulate matter. The results partly support the thesis that low concentrations lead to different biodegradation kinetics compared to the concentrations used in the standard tests. Furthermore the biodegradation rates of the chemicals studied, particularly of 4-chloroaniline, in Finnish natural waters appeared to be lower than those reported in some other countries.     

Photoinduzierte hydroxylierungsreaktionen organischer chemikalien in natürlichen Gewässern - Nitrate als potentielle OH-radikalquellen -

Organic chemicals are concentrated in natural waters, where they undergo complex reactions under the influence of solar radiation and catalyzed by substances such as humic acid as well as nitrate and nitrite salts. Nitrates are present in high concentrations in natural waters (5 – 50 mg/l). The photolysis of the nitrate ion leads to the formation of OH-radicals. In this investigation the steady-state concentration of OH-radicals in different aquatic environments is estimated (～ 5 · 10^?16 mol/l). It depends on the amount of nitrate dissolved in the water. Under the conditions of this work the half life for a great number of organic chemicals lies in the range 80 – 400 hours (for the reaction with OH-radicals).