利用含铝废盐酸制备聚合氯化铝

以某医药企业产生的含铝废盐酸为原料制备了液体聚合氯化铝(PAC)。确定了适宜的有机物去除方法和碱化剂,考察了碱化剂投加量、废盐酸铝离子含量等合成条件对PAC产品指标的影响,并比较了自制PAC和市售PAC对该企业污水站二沉池出水的混凝效果。实验结果表明:采用活性炭吸附法去除废盐酸中有机物,选择固体Ca O作为碱化剂,在活性炭投加量1‰(w)、吸附时间1 h、铝离子含量9.5%(w,以Al_2O_3计)、CaO投加量80 g/L、反应时间24 h的条件下,制备的液体PAC达到行业标准HG/T 2677—2017《工业聚氯化铝》中的Ⅲ类标准;自制PAC对废水COD和SS的去除率均优于市售PAC,不仅可替代其使用,还可外售产生经济效益。     

γ-Al_2O_3负载多金属复合催化剂选择性催化还原烟气脱硝

以γ-Al_2O_3作为载体,先后负载CeO_2,MnC_2O_4,Fe(NO_3)_3,CrO_3,Ni(NO_3)_2,NH_4VO_3等多种金属组分制备γ-Al_2O_3负载多金属复合催化剂,并用于模拟烟气的选择性催化还原脱硝。通过SEM和XRD技术对催化剂进行了表征。表征结果显示:Fe,Mn,Cr的添加能增加催化剂的低温催化活性、提高催化剂的N2选择性;γ-Al_2O_3对活性金属氧化物的负载效果良好。实验结果表明:各金属化合物的最佳加入量为w(MnC_2O_4·2H_2O)=2 0%,w(Fe(NO_3)_3·9H_2O)=1 5%,w(CrO_3)=10%,w(Ni(NO_3)_2·6H_2O)=5%,w(NH_4VO_3)=10%,w(CeO_2)=5%,w(γ-Al_2O_3)=35%;以在最佳正交实验条件下制得的γ-Al_2O_3负载多金属复合物为催化剂,在脱硝反应温度为205℃的条件下,NO转化率为96.7%;γ-Al_2O_3负载多金属复合催化剂经5次重复使用,NO转化率仍可稳定在94%左右。     

铬污染土壤处理中的铬含量及形态变化

采用FeSO_4和Na_2S作为还原剂处理铬污染紫色土壤,研究了还原过程中铬的含量及形态的变化。实验结果表明:当FeSO_4加入量为1.5%(w,下同)时,浸出Cr(Ⅵ)含量由(1 745.13±27.93)mg/kg降至(17.65±2.28)mg/kg,浸出总铬含量由(1 768.83±57.24)mg/kg降至(69.79±8.61)mg/kg,铬形态由水溶+碳酸盐结合态转变到较稳定的铁锰结合态;当Na_2S加入量为0.4%时,浸出Cr(Ⅵ)含量由(1 745.13±27.93)mg/kg降至(25.50±0.12)mg/kg,浸出总铬含量由(1 768.83±57.24)mg/kg降至(410.87±12.83)mg/kg,铬形态由水溶+碳酸盐结合态转变到铁锰结合态和有机结合态。     

铁矿石烧结烟气脱硫灰处理含铬废水

在分析铁矿石烧结烟气脱硫灰成分的基础上,利用脱硫灰中的亚硫酸盐还原废水中的Cr(Ⅵ),再加碱中和,通过沉淀去除铬。在初始废水pH 1.0、脱硫灰加入量0.06 g/mg(以Cr(Ⅵ)计)、振荡转速160 r/min、振荡时间25 min、中和pH 7.5的最佳工艺条件下处理模拟含铬废水,Cr(Ⅵ)质量浓度由10.00 mg/L降至0.18 mg/L,去除率达98.2%。最佳工艺条件下处理3种实际含铬废水,处理后出水的Cr(Ⅵ)和总铬的质量浓度及pH均满足GB 8978—1996《污水综合排放标准》。实现了对脱硫灰的综合利用、化害为利和以废治废的目标。     

臭氧氧化—湿式钙法吸收工艺对烟气的同时脱硫脱硝

采用臭氧氧化—湿式钙法吸收工艺对模拟烟气进行同时脱硫脱硝处理。O_3于150℃下具有较高的热稳定性,可将NO氧化为高价态氮氧化物,且NO氧化率随n(O_3)∶n(NO)的增大而逐渐提高。烟气中SO_2和H_2O的存在对NO氧化率的影响不大。O_3对SO_2的氧化率较低,约为5%。3%(w)石灰石浆液对SO_2的吸收率接近100%,NO_x吸收率随n(O_3)∶n(NO)的增大而逐渐提高,当n(O_3)∶n(NO)为1.6时NO_x吸收率可达约65%。SO_2能促进吸收液对NO_x的脱除。石灰石浆液中加入0.2%(w)的(NH_4)_2SO_3或Na_2SO_3后NO_x吸收率可达约85%或82%,且吸收率随添加剂加入量的增加而提高,添加(NH_4)_2SO_3的NO_x吸收率略高于添加Na_2SO_3。     

酸浸—萃取—沉淀法回收废锂离子电池中的钴

采用酸浸—萃取—沉淀法回收废锂离子电池中的钴。实验结果表明:废锂离子电池在600℃下煅烧5 h可将正极材料上的有机黏结剂与正极活性物质分离;正极活性物质在Na OH溶液浓度为2.0 mol/L、n(Na OH)∶n(铝)=2.5、碱浸温度为20℃的条件下碱浸反应1 h后,铝浸出率达99.7%;已除铝的正极活性物质在硫酸浓度为2.5 mol/L、H_2O_2质量浓度为7.25 g/L、液固比为10、酸浸温度为85℃的条件下酸浸反应120 min,钴浸出率高达98.0%;酸浸液在p H为3.5、萃取剂P507与Cyanex272体积比为1∶1的条件下,经2级萃取,钴萃取率为95.5%;采用H_2SO_4溶液反萃后在硫化钠质量浓度为8 g/L、反萃液p H为4的条件下沉淀反应10 min,钴沉淀率达99.9%。     

国外动态

萘酚生产废水含有大量无机盐(Na_2SO_4、Na_2SO_3)和有机物(β-萘磺酸和其他)。采用电渗析法可以有效地净化该废水,并能得到氢钣化钠和硫酸。实验是在装有离子膜、铂钛阴极和阳极的三室电渗析器内进行。离子膜牌号为 MK-40和 MA-40,电流密度为0.08—0.12安/厘米~2。电解4～5小时,无机盐去除率达97—99%,有机物去除率达95—98%(按 COD 计)。净化后的废水可回用。阴极电解液硫酸(70克/升)和阳极电解液氢氧化钠(60克/     

纳米Al_2O_3固定化红平红球菌菌球的制备及其对苯酚的降解

以海藻酸铝为主要包埋材料、纳米Al_2O_3为添加剂,包埋固定红平红球菌,制得纳米Al_2O_3固定化红平红球菌菌球,并将其用于苯酚的降解。表征结果显示:菌球内部包含丰富的菌丝体;内部孔径以中孔居多。实验结果表明:菌球的最优制备方案为0.05 g纳米Al_2O_3加入3 m L海藻酸钠溶液中、海藻酸钠质量分数6%、微生物包埋量0.5 m L/m L(以海藻酸钠溶液计)、Al_2(SO_4)_3质量分数3%;在初始苯酚质量浓度为400 mg/L、反应时间为24h、菌球加入量为8 g/L、反应p H为8.0、反应温度为30℃的条件下,菌球首次使用时可使苯酚完全降解,使用5次后的苯酚降解率仍达93%以上,具有良好的循环使用性。     

萃取法从粉煤灰生产Al_2O_3废水中回收偏硅酸钠

采用由C_1~C_4低碳醇组成的复配萃取剂萃取回收粉煤灰生产Al_2O_3废水(脱硅液)中的偏硅酸钠,在提取产品偏硅酸钠的同时回收脱硅液中的碱。直接进行萃取时偏硅酸钠易流失,萃取剂用量大,回收成本较高。将脱硅液浓缩后再进行萃取,萃取剂用量大幅减少,回收成本明显下降。将萃取剂成本与浓缩所需成本之和最低时的最佳浓缩比下、脱硅液与萃取剂体积比为1∶0.8时回收的偏硅酸钠干燥处理,干燥后的偏硅酸钠中Na_2O含量(w)大于20.5%,SiO_2含量大于20.0%,水不溶物含量小于0.05%,铁含量小于0.05%,白度大于70%,产品符合HG/T2568—2008《工业偏硅酸钠》标准。     

废铝易拉罐粉末对U(Ⅵ)的去除效果与机理

以废铝易拉罐为原料,通过除漆、研磨等制得废铝易拉罐粉末(SAlCP)。利用SAlCP处理含U(VI)废水,优化处理工艺条件,采用SEM和XPS技术对SAlCP进行表征,并探讨了SAlCP去除U(Ⅵ)的机理。实验结果表明:在反应温度为30℃、溶液初始pH为5.0、U(Ⅵ)初始质量浓度为10 mg/L、SAlCP投加量为4 g/L、反应时间为120 min的优选条件下,U(Ⅵ)的去除率达98.2%。SAlCP去除U(Ⅵ)的反应过程可用拟一级动力学模型和Langmuir-Hinshelwood模型能较好地拟合。SAlCP的作用机理是还原沉淀-吸附共沉,且还原作用是SAlCP去除U(Ⅵ)的主要途径。     

粉煤灰制聚合氯化铝铁和白碳黑新工艺

采用粉煤灰制备聚合氯化铝铁和白碳黑.该法共分一次酸浸、碱溶、焙烧、二次酸浸4个阶段.实验确定的最佳工艺条件为:一次酸浸阶段酸溶温度100℃,碱溶阶段m(氢氧化钠):m(活化高硅渣)=0.6,二次酸浸阶段m(碳酸钠):m(灰渣A)=0.8、盐酸质量分数20%.在此条件下Fe~(3+)和Al~(3+)的总浸出率分别为96.54%和86.67%.主要产品聚合氯化铝铁的质量符合GB15892-2003<水处理剂聚氯化铝>的标准;产品白碳黑的质量符合GBl0517-89<沉淀二氧化硅>的标准.     

拜耳法赤泥制备三聚磷酸铝

拜耳法赤泥经石灰石烧结改性、盐酸浸取及碱液处理等工序得到氢氧化铝干胶,再以氢氧化铝干胶和工业磷酸为原料,通过中和反应、缩合反应和水化反应合成三聚磷酸铝.经单因素条件实验和正交实验得到最佳工艺条件为:磷酸体积(mL)与氢氧化铝干胶质量(g)的比3,中和反应温度常温,缩合反应温度290℃,缩合反应时间4h.在最佳工艺条件下合成的试样中,Al2O3和P2O5的含量与工业三聚磷酸铝ATP-200相近,经IR分析,该试样即为三聚磷酸铝.盐雾试验结果表明合成的三聚磷酸铝的防腐性能达到ATP-200的性能指标.     

Ceramic processing of incinerator bottom ash

The <8 mm fraction of aged incinerator bottom ash from a commercial incinerator (energy from waste) plant has been collected at regular intervals, characterised and processed to form ceramic materials. Ashes were sieved, wet ball milled, dried, compacted and sintered at temperatures between 1080 and 1115 degrees C. Variations in the chemical composition and mineralogy of the milled ash, and the mineralogy, physical properties and leaching of sintered products have been assessed. Milling produces a raw material with consistent chemical and mineralogical composition with quartz (SiO(2)), calcite (CaCO(3)), gehlenite (Ca(2)Al(AlSi)O(7)) and hematite (Fe(2)O(3)) being the major crystalline phases present. Different batches also milled to give consistent particle size distributions. Sintering milled incinerator bottom ash at 1110 degrees C produced ceramics with densities between 2.43 and 2.64 g/cm(-3) and major crystalline phases of wollastonite (CaSiO(3)) and diopside (CaMgSi(2)O(6)). The sintered ceramics had reduced acid neutralisation capacity compared to the as-received ash and exhibited reduced leaching of Ca, Mg, Na and K under all pH conditions. The leaching of heavy metals was also significantly reduced due to encapsulation and incorporation into glassy and crystalline phases, with Cu and Al showing greatly reduced leaching under alkali conditions.     

加拿大一枝黄花纤维素的改性及其对Cr(Ⅵ)的吸附

采用环氧氯丙烷和三甲胺对加拿大一枝黄花纤维素进行改性,改性后的加拿大一枝黄花纤维素对Cr(Ⅵ)具有一定的吸附作用.在改性加拿大一枝黄花纤维素加入量为3.2 g/L、吸附温度为40℃、吸附时间为240 min、溶液pH为2的条件下,对初始Cr(Ⅵ)质量浓度为20 mg/L的K2Cr2O7溶液进行吸附实验,Cr(Ⅵ)吸附量可达5.69 mg/g,Cr(Ⅵ)去除率为91％.动力学研究结果表明,改性加拿大一枝黄花纤维素对Cr(Ⅵ)的吸附以液膜扩散为控制步骤,反应过程符合Boyd液膜扩散方程,相关系数达到0.995 47.     

高炉渣制备聚硅酸硫酸铝铁混凝剂

以高炉渣为原料,分别采用酸浸及碱浸-酸化工艺得到铁、铝离子及聚硅酸,再将铁、铝离子引入聚硅酸制得聚硅酸硫酸铝铁(PSAFS)混凝剂。考察了PSAFS的聚合条件对焦化废水混凝效果的影响,并与市售混凝剂进行了对比。实验结果表明:PSAFS的最佳制备条件为n(Al+Fe)∶n(Si)=0.53,混凝剂p H=1,熟化时间0.5 h,熟化温度60℃;PSAFS加入量为4 m L/L时,混凝效果最好,对焦化废水的浊度和COD的去除率分别达到98.9%和74.5%;PSAFS的性能优于市售的3种混凝剂。     

生态修复植物蜈蚣草中砷的回收

采用管式炉高温热解-NaOH-Na₂CO₃混合液碱浸-CuSO₄·5H₂O沉淀的方法回收生态修复植物蜈蚣草中的砷，最终得到产品砷酸铜。该方法的最佳工艺条件为：热解温度600 ℃，热解时间30 min，CaO加入量（CaO与蜈蚣草的质量比）8%； m（NaOH）∶m（Na₂CO₃）=1∶3，碱浸温度70 ℃， 碱浸时间2 h， 固液比1∶10； 沉淀反应pH 5， 沉淀反应温度70 ℃。采用该方法处理生态修复植物蜈蚣草，得到产品砷酸铜的纯度为93%，砷回收率达88%。     

Immobilization of lead and zinc in scrubber residues from MSW combustion using soluble phosphates

The immobilization of MSWI-scrubber residues with soluble PO4(3-) was studied and compared to the immobilization using cement. The DIN 38414-S4 leaching protocol and pH dependent leaching were used to evaluate the leaching of Pb and Zn. Four different scrubber residues from MSW combustion (Pb concentration: 2.8-4.8 mg/g; Zn concentration: 3.0-12.3 mg/g) were mixed with water and cement or Na2HPO4 as source of soluble PO4(3-) at dosages of at least 0, 0.1, 0.2, 0.3 and 0.4 g per g residue. With cement as well as with PO4(3-) a reduction in Pb and Zn leaching was observed. With 0.4 g cement per g residue, the Pb leaching was reduced by a factor ranging from 70 to 100, but still exceeded the Pb landfill limit of 2 mg/l. With PO4(3-) the Pb leaching was reduced with a factor of 100-300 to below 2 mg/l. The Zn landfill limit (10 mg/l) was only exceeded by one untreated residue. Adding 0.2 g cement or 0.1 g PO4(3-) per g of that residue was enough to reduce leaching below 10 mg/l. However, when 0.6 g Na2HPO4 per g residue was added to a lime based scrubber residue, an increase in Zn leaching up to 12.5 mg/l was observed due to an increase in pH of up to 13.0. When using NaH2PO4 and H3PO4 no such increase in Zn leaching was observed. pH dependent leaching performed on one of the four residues showed that in the pH range of 2.5-6, Pb leaching was 100-50 times lower with Na2HPO4 treatment than with cement. In the pH range from 7-11, almost equal results were obtained for cement treated and Na2HPO4 treated residue. Above a pH of 12, Pb leaching was three times lower for the PO(4)(3-)-treated residue than for the cement treated residue. With soluble PO4(3-), Pb leaching below 2 mg/l could be attained at a dosage of 0.27 g PO4(3-)/g residue. With cement, Pb leaching was never below 2 mg/l.     

Leaching behaviour of elements and evaluation of pre-treatment methods for municipal solid waste incinerator residues in column leaching tests.

Two new pre-treatment methods (water-washing/carbonation and carbonation/phosphate stabilization) of municipal solid waste (MSW) incinerator residues were evaluated by column leaching tests under aerobic conditions and anaerobic conditions (which were changed to aerobic conditions after 10 months). A mixture of bottom ash and fly ash (5:1 ratio) was pre-treated using each method. Shredded incombustible residues (SIR) were added to each ash preparation in proportions similar to the ratios present in landfills. For comparison, landfill wastes typical of Japan, namely, a mixture of bottom ash, chelating-pre-treated fly ash, and SIR, were also examined. Leachate samples were collected periodically and analysed over a 15-month period. When compared with chelating pretreatment, both water-washing/carbonation and carbonation/ phosphate stabilization reduced the leaching of Pb, Al, and Cu by about one to two orders of magnitude. Moreover, the initial concentrations of Ca and Pb in leachates from column of water-washing/carbonation were 56-57% and 84-96% less than those from the column of carbonation/phosphate stabilization. Therefore, water-washing/carbonation was considered to be a promising approach to obtain early waste stabilization and to reduce the release of heavy metals to near-negligible levels. The leaching behaviour of elements was also discussed.     

天然膨润土还原吸附Cr（Ⅵ）

以天然膨润土为吸附剂，还原吸附处理含Cr（Ⅵ）模拟废水。实验结果表明：以（NH₄）₂FeSO₄为还原剂吸附效果最佳；在还原剂加入量为理论值的0.8倍、膨润土加入量为6 g/L、吸附时间为30 min、吸附温度为30 ℃、初始Cr（Ⅵ）质量浓度为1 mg/L的条件下，Cr（Ⅵ）去除率可达99.6%，处理后模拟废水中总铬质量浓度低至0.003 mg/L。天然膨润土对Cr（Ⅵ）的还原吸附符合准二级动力学模型及Freundlich等温吸附模型。