亚铁催化声化学降解罗丹明B

比较了不同金属离子对罗丹明B的声化学降解作用，发现超声时加入Fe^2＋反应速率常数为单独超声波降解时的1．6倍，反应在前5h内符合假一级动力学。研究了亚铁离子强化声化学对罗丹明B的降解作用，考察了Fe^2＋用量，溶液初始pH值，曝气，反应温度和超声功率等因素对脱色速率的影响。研究表明，酸性条件有利于染料的脱色；有曝气时的声化学脱色速率常数是单独超声时的6倍；声化学反应的活化能较低，反应在低温就可以进行；超声功率的改变对脱色速率的影响不大。UV-VIS扫描图谱显示，染料在225nm和256nm处的紫外吸收明显降低，初步探讨了罗丹明B的降解机理。     

Fe/活性炭多相类Fenton法湿式氧化罗丹明B废水的研究

采用自制的Fe/活性炭（Fe/AC）为催化剂，H₂O₂为氧化剂,组成多相类Fenton试剂催化降解罗丹明B染料废水。实验结果表明,在催化剂加入量为0.8 g/L，H₂O₂体积分数为0.3%,废水pH值为13,反应时间为30 min的条件下,质量浓度为200 mg/L的罗丹明B染料废水的脱色率达100%。反应动力学研究表明,罗丹明B脱色反应近似为一级反应,30℃时反应速率常数为0.02675 min^-1,表观活化能为69.47 kJ/mol。     

TiO_2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有：X射线衍射光谱（XRD）、激光散射粒径分布、傅立叶变换红外光谱（FT-IR）、X射线光电子谱（XPS）和透射电子显微镜（TEM）。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂（H2O2）用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明：制备的TiO2胶体粒子平均粒径为13.8 nm（激光散法测定）,光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/（L.min）,平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2（含量30%）用量为0.2%（V/V）,光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

壳聚糖在固定化光合细菌处理染料活性艳红X-3B中的应用研究

采用海藻酸钠对光合细菌进行包埋,并在固定化过程中加入壳聚糖,研究添加了壳聚糖的固定化细胞在不同条件下对活性艳红X-3B的脱色效果及其降解动力学.实验结果表明,在厌氧条件下,X-3B的脱色效果较好;染料浓度在30～300 mg/L之间变化时,厌氧降解动力学方程均符合一级动力学方程;降解速率与染料初始浓度之间关系符合Michaelis-Menten方程,反应动力学参数Km=374.96 mg/L,Vmax=7.53 mg/L·h.振荡有利于脱色并使半衰期缩短;固定化小球可重复使用.     

臭氧/Mn2+催化降解水溶液中的2,4-二氯苯氧乙酸

以Mn2 为催化剂与臭氧联合降解除草剂2,4-二氯苯氧乙酸(2,4-D).考察了反应温度、pH、2,4-D初始浓度和臭氧气体流量等因素对2,4-D降解效果的影响.pH对2,4-D降解效果影响很大,当pH=2.0、反应5 min时,2,4-D的去除率达99.8%;当pH=10.1、反应20min时,2,4-D的去除率仅为50.0%.反应温度升高、臭氧气体流量增加、2,4-D初始浓度降低均有助于2,4-D降解速率的提高.单独臭氧氧化2,4-D的表观反应速率常数为0.170 min-1;催化臭氧氧化2,4-D的表观反应速率常数为0.295min-1,是单独臭氧氧化的1.74倍.2,4-D的Mn2 催化臭氧反应遵循拟一级反应动力学方程.     

丙酮酸钠光解引发染料水溶液的脱色

对丙酮酸钠紫外光解所引发的染料橙黄Ⅱ的脱色进行了研究,讨论了pH值、丙酮酸钠初始浓度、染料初始浓度及外加Fe(Ⅲ)对橙黄Ⅱ光致脱色的影响,比较了4种染料的脱色效果,并对反应机理进行了初步探讨.实验表明,丙酮酸盐对染料有较高的光降解脱色效率;pH为3.0～8.0的范围内,橙黄Ⅱ都有很高的脱色率;丙酮酸盐的初始浓度越大,橙黄Ⅱ脱色率和反应初始速率越大;橙黄Ⅱ浓度越大,其脱色率越低,但反应初始速率变化不大;外加Fe(Ⅲ)会抑制橙黄Ⅱ脱色;Fe(Ⅲ)-丙酮酸在水体中也能产生·OH;橙黄Ⅱ的脱色是由丙酮酸钠光解产生的活性自由基等所致,但不是·OH.     

壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B动力学研究

采用仿生矿化法制备了壳聚糖/纳米CdS复合颗粒光催化剂,并用于可见光光催化降解猩红B染料模拟废水,研究了猩红B初始浓度、pH、催化剂投加量和催化剂重复使用次数等因素对猩红B光催化降解的影响.X射线衍射(XRD)分析表明,壳聚糖能有效负载CdS纳米微晶.采用Langmuir-Hinshelwood模型描述壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B反应动力学行为,在猩红B初始质量浓度较低(≤20 mg/L)时,光催化降解过程符合假一级动力学方程.降低猩红B初始浓度和溶液pH都可显著增大光催化降解速率常数;催化剂投加量小于0.7 g/L时,光催化降解速率随其增加而增大,但催化剂投加量过大会使光催化降解速率减小;催化剂重复使用第5次时,猩红B光催化降解速率常数仍为第1次使用时的63.4%.     

UV/Fenton法处理酸性红B研究

采用UV/Fenton高级氧化技术对酸性红B模拟废水进行处理,当进水浓度为400mg/L时,确定了各影响因素的最佳投加量:H2O2投加量为2 mL/L,Fe2 投加量为0.08g/L,最佳pH值为4;并采用一级动力学公式对酸性红B降解速率进行拟合,研究了反应条件对速率常数的影响.最后通过对单独UV法、单独Fenton法和UV/Fenton法3种处理方法效果的比较,发现UV与Fenton试剂具有协同作用.     

3种染料化合物在UV-TiO2/H2O2和UV-TiO2体系中的光催化降解研究

采用自制的TiO2膜和平板式固定床型光催化氧化反应装置,对甲基橙、茜素红和罗丹明B 3种含有不同生色基团的染料化合物进行了TiO2光催化氧化降解研究,通过对照测定降解过程中吸光度、电导率、pH的变化,分析了在加入和不加入H2O22种情况下降解过程的异同,比较了3种染料化合物脱色的难易程度,揭示了降解产物中无机离子的变化规律及某些可能的产物类型.     

Fe~(3+)掺杂TiO_2/凹凸棒复合材料的光催化性能

采用酸催化的溶胶-凝胶法制备了一系列Fe3+掺杂TiO2/凹凸棒(Fe3+-TiO2/ATP)复合光催化剂材料。在可见光条件下,以亚甲基蓝(MB)溶液的光催化降解反应,评价了样品的光催化性能,研究了TiO2负载量、Fe3+掺杂量和焙烧温度对复合材料光催化性能的影响。在单因素实验的基础上,采用正交实验设计(L25(53))优化了催化剂的制备条件。光催化实验结果表明,MB在复合材料上的光催化降解反应遵循Langmuir-Hinshelwood(L-H)动力学模型。正交实验结果表明,当TiO2负载量为15%、Fe3+掺杂量为0.5%和焙烧温度为550℃时,得到的复合材料对MB的光催化降解效率最佳,测得表观反应速率常数kapp为6.09×10-3min-1,反应4 h后MB的降解率(Dt)可达75.88%,相同实验条件下与P25(1.51×10-3min-1)相比较,反应速率提高了4.03倍,降解率提高了45.05%。另外,复合材料的沉降性能优于P25,易于分离,是一类有应用前景的复合光催化剂。     

Sonochemical substrate selectivity and reaction pathway of systematically substituted azo compounds

The sonochemical degradation of the systematically substituted azo compound 2,7-dihydroxy-1-phenylazonaphthaline-3,6-disulfonic acid was investigated using a frequency of 850 kHz and an acoustic input power of 61 W. All derivatives were degraded completely within 6h by the ultrasonic treatment. Trifluoromethyl substituted azo compounds exhibited 2-3-fold higher degradation rates in comparison to the reference hydrogen substituted azo compound (k=0.54 h(-1)). In contrast to enzymatic processes (azoreductase or laccase), the ultrasonic treatment for these ortho-, meta-, and para-substituted azo compound showed 1.5-50-fold higher degradation rates. Additionally the ultrasound treatment was characterized by shorter reaction times. As a result of the detection and identification of specific intermediates using LC-MS a reaction pathway of the sonochemical degradation of the analysed azo compound is proposed indicating the formation of cyclohexadienone and naphthalene quinone derivatives.     

氯甲烷与偶氮染料混合废水的超声脱色

使用40 kHz超声(US)脱色氯甲烷(包括CCl4、CHCl3和CH2Cl2)与偶氮染料(包括甲基橙与铬黑T)混合模拟废水,考察了氯甲烷初始浓度对偶氮染料超声脱色和TOC去除的影响.结果表明:偶氮染料的单独超声脱色速率很慢;而在CCl4与CHCl3存在时超声能使偶氮染料短时间内脱色至无色,但对其TOC的超声去除促进作...     

Effect of carbon tetrachloride on sonochemical decomposition of methyl orange in water

Two types of sonicators were used for the sonochemical decomposition of methyl orange (MO) in the presence and absence of carbon tetrachloride (CCl4): One is a 45kHz ultrasonic cleaning bath (a low intensity sonicator) and the other is a 200kHz ultrasonic reactor (a high intensity sonicator). It was clearly confirmed that the rates of the sonochemical decomposition of MO increased with increasing the concentration of CCl4 in both sonicators. The enhancement effect of CCl4 was much higher in the high intensity sonicator than in the low intensity one: by the addition of 100ppm of CCl4, the decomposition ratio of MO with the high intensity sonicator became 41 times larger, while that with the low intensity sonicator became 4.8 times larger. Based on the obtained results, it was suggested that the formed cavitation phenomenon was different between sonicators. It was also suggested that the sonochemical decomposition of MO in the presence of CCl4 would be useful to evaluate the sonochemical efficiency, because the rate of MO decomposition can be effectively enhanced by the sonolysis of CCl4.     

双频超声辐射协同H_2O_2降解偶氮染料废水的研究

采用双频超声协同H2O2降解酸性绿20染料废水,考察超声功率密度、染料初始浓度和pH、饱和气体及H2O2投加量等因素对酸性绿20降解效果的影响,结果表明,在给定实验条件下,双频降解效果优于单频超声波,且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解,当染料废水初始pH=4可取得最佳的降解效果;酸性绿20的降解效率随染料初始浓度的增大而降低,其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H2O2,可取得最佳的降解效果。在优化实验条件下,采用双频超声协同H2O2降解5 h,酸性绿20的色度和TOC去除率分别为94.6%和36.3%;分析降解前后的紫外-可见光谱图可知,酸性绿20并非完全被降解为CO2和H2O,而是生成一些小分子有机中间体。     

双频超声辐射协同H2O2降解偶氮染料废水的研究

采用双频超声协同H₂O₂降解酸性绿20染料废水，考察超声功率密度、染料初始浓度和pH、饱和气体及H₂O₂投加量等因素对酸性绿20降解效果的影响，结果表明，在给定实验条件下，双频降解效果优于单频超声波，且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解，当染料废水初始pH=4可取得最佳的降解效果；酸性绿20的降解效率随染料初始浓度的增大而降低，其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H₂O₂，可取得最佳的降解效果。在优化实验条件下， 采用双频超声协同H₂O₂降解5 h，酸性绿20的色度和TOC去除率分别为94.6%和36.3%；分析降解前后的紫外可见光谱图可知，酸性绿20并非完全被降解为CO₂和H₂O，而是生成一些小分子有机中间体。     

Mechanism of decolorization and degradation of CI Direct Red 23 by ozonation combined with sonolysis

The decolorization and degradation of CI Direct Red 23, which is suspected to be carcinogenic, were investigated using ozonation combined with sonolysis. The results showed that the combination of ozonation and sonolysis was a highly effective way to remove color from waste water. The operational parameters, namely concentration of the dye, pH, ozone dose and ultrasonic density, were investigated during the process. The decolorization of the dye followed pseudo-first-order kinetics. Increasing the initial concentration of Direct Red 23 led to a decreasing rate constant. The optimum pH for the reaction was 8.0, and both lower and higher pH decreased the removal rate. The effect of the ozone dose on the dye decolorization was much greater than that of the sonolysis density. Intermediates such as naphthalene-2-sulfonic acid, 1-naphthol, urea and acetamide were detected by gas chromatography coupled with mass spectrometry in the absence of pH buffer, while nitrate and sulfate ions and formic, acetic and oxalic acids were detected by ion chromatography. A tentative degradation pathway was proposed without any further quantitative analyses. During the degradation, all nitrogen atoms and phenyl groups of Direct Red 23 were degraded into urea, nitrate ion, nitrogen and formic, acetic and oxalic acids, etc.     

Sonochemical degradation of 2,3,7,8-tetrachlorodibenzo-p-dioxins in aqueous solution with Fe(III)/UV system

2,3,7,8-Tetrachlorodibenzo-p-dioxin (2,3,7,8-TeCDD) was rapidly decreased by sonication in aqueous solution. The degradation efficiency was strongly influenced by ultrasonic power and reaction temperature. An initial 2,3,7,8-TeCDD concentration of 20 ng l(-1) was completely degraded within 60 min under sonochemical conditions using a 20 kHz frequency with a 150 W ultrasound power. The activation energy is 21.9 kJ/mol in the temperature range of 10-40 degrees C, suggesting a diffusion-controlled reaction. To increase the efficiency of 2,3,7,8-TeCDD treatment, degradation system combined ultrasound with Fe(III) (2 x 10(-4)mol l(-1)) and UV irradiation. Both UV and Fe(III) induced Fenton, Fenton-like and photo-Fenton reactions, leading to additional OH radicals and rapid 2,3,7,8-TeCDD removal.