Field testing of conversion of sewage sludge to daily landfill cover material

Solidification of sewage sludge has been actively investigated in Japan and Europe since the 1970s. Most previous studies have focused on only the mechanical aspects of potential alternative cover soil made using sewage. Most solidification processes, however, suffer from severe odor problems because of the high alkalinity of the material. The objectives of this study are to develop a cost-effective solidifying agent for conversion of sewage sludge in order to reduce the odor generation, as an alternative to the conventional cement lime-based solidifying agent, and to demonstrate its applicability in the field experimentally. Field test results showed compressive strength well above the 1.0 kg/cm² criterion for landfill cover soil in Korea. Also, the permeability coefficient was far below the 5 × 10⁻⁵ cm/s design criterion for landfill cover soil. Even in harsh weather conditions, such as in winter and summer, the compressive strength was increased. In addition, the permeability was decreased from 3.45 × 10⁻⁶ cm/s to 4.78 × 10⁻⁷ cm/s, and from 2.27 × 10⁻⁶ cm/s to 3.62 × 10⁻⁷ cm/s, at 7 days after placement in January and August, respectively. It can therefore be postulated that the proposed solidification process is an appropriate alternative for production of daily landfill cover material. Concerning the odor problem, 5 min of mixing of sewage with TS103, one of the proprietary agents used in this work, was sufficient to suppress the concentration of ammonia emitted to below 10 ppm. Considering all of these experimental field test results, it is expected that the proposed method could be a competitive approach for manufacture of alternative landfill cover material.     

Chemical Recycling of Polyamide Waste at Various Temperatures and Pressures Using High Pressure Autoclave Technique

Chemical recycling of polyamide waste in water was studied using 0.5 L high pressure autoclave at temperatures of 150, 200, 210, 220,230 and 240 °C and at various pressures of 100, 200, 300, 400, 500, 600 and 700 psi (pound per square inch). Viscosity average molecular weight of the polyamide waste sample was determined by Ostwald method and recorded as 1.928 × 10³. The reaction was found to be first order with velocity constant in order of 10⁻² min⁻¹. The velocity constant and percent conversion of depolymerization reaction at 240 °C and 700 psi pressure were recorded as 2.936 × 10⁻² min⁻¹ and 99.99% respectively. The velocity constant was obtained on the basis of measurement of amine value. Kinetic and thermodynamic parameters such as energy of activation, frequency factor, enthalpy of activation were found to be 10.6 kJ mole⁻¹, 0.3719 min⁻¹ and 6.3 kJ mole⁻¹ respectively, at the optimum conditions for maximum depolymerization of polyamide waste.     

Assessing the environmental impact of ashes used in a landfill cover construction

Large amounts of construction materials will be needed in Europe in anticipation for capping landfills that will be closed due to the tightening up of landfill legislation. This study was conducted to assess the potential environmental impacts of using refuse derived fuel (RDF) and municipal solid waste incineration (MSWI) ashes as substitutes for natural materials in landfill cover designs. The leaching of substances from a full-scale landfill cover test area built with different fly and bottom ashes was evaluated based on laboratory tests and field monitoring. The water that drained off above the liner (drainage) and the water that percolated through the liner into the landfill (leachate) were contaminated with Cl^?, nitrogen and several trace elements (e.g., As, Cu, Mo, Ni and Se). The drainage from layers containing ash will probably require pre-treatment before discharge. The leachate quality from the ash cover is expected to have a minor influence on overall landfill leachate quality because the amounts generated from the ash covers were low, <3–30 l (m² yr)^?1. Geochemical modelling indicated that precipitation of clay minerals and other secondary compounds in the ash liner was possible within 3 years after construction, which could contribute to the retention of trace elements in the liner in the long term. Hence, from an environmental view point, the placement of ashes in layers above the liner is more critical than within the liner.     

Liquid balance monitoring inside conventional,Retrofit, and bio-reactor landfill cells

The Outer Loop landfill bioreactor (OLLB) in Louisville, KY, USA has been the site of a study to evaluate long-term bioreactor performance at a full-scale operational landfill. Three types of landfill units were studied including a conventional landfill (Control cell), a new landfill area that had an air addition and recirculation piping network installed as waste was being placed (As-Built cell), and a conventional landfill that was modified to allow for liquids recirculation (Retrofit cell). During the monitoring period, the Retrofit, Control, and As-Built cells received 48, 14, and 213 L Mg^?1 (liters of liquids per metric ton of waste), respectively. The leachate collection system yielded 60, 57 and 198 L Mg^?1 from the Retrofit, Control, and As-Built cells, respectively. The head on liner in all cells was below regulatory limits. In the Control and As-Built cells, leachate head on liner decreased once waste placement stopped. The measured moisture content of the waste samples was consistent with that calculated from the estimate of accumulated liquid by the liquid balance. Additionally, measurements on excavated solid waste samples revealed large spatial variability in waste moisture content. The degree of saturation in the Control cells decreased from 85% to 75%. The degree of saturation increased from 82% to 83% due to liquids addition in the Retrofit cells and decreased back to 80% once liquid addition stopped. In the As-Built cells, the degree of saturation increased from 87% to 97% during filling activities and then started to decrease soon after filling activities stopped to reach 92% at the end of the monitoring period. The measured leachate generation rates were used to estimate an in-place saturated hydraulic conductivity of the MSW in the range of 10^?8 to 10^?7 m s^?1 which is lower than previous reports. In the Control and Retrofit cells, the net loss in liquids, 43 and 12 L Mg^?1, respectively, was similar to the measured settlement of 15% and 5–8% strain, respectively (Abichou et al., 2013). The increase in net liquid volume in the As-Built cells indicates that the 37% (average) measured settlement strain in these cells cannot be due to consolidation as the waste mass did not lose any moisture but rather suggests that settlement was attributable to lubrication of waste particle contacts, softening of flexible porous materials, and additional biological degradation.     

Kinetics and Thermodynamics of Hydrolytic Depolymerization of Polyamide Waste at Various Temperature and Autogenious Pressure by High-Pressure Autoclave

Hydrolytic depolymerization of polyamide waste in water was studied using 0.5 L high pressure autoclave at temperatures of 235, 240, 245, 250 °C and at autogenious pressure 480, 500, 520, and 600 psi (pound per square inch).The reaction rate constant, energy of activation, enthalpy of activation, entropy of activation and equilibrium constant were calculated from the experimental data obtained. The maximum depolymerization (59.2%) of polyamide waste into monomer caprolactum was obtained at 250 °C and 600 psi pressure. The reaction rate constant was obtained on basis of measurement of amine value and residual weight. The depolymerization reaction was found to be pseudo first order with reaction rate constant of the order of 10⁻³ min⁻¹. The enthalpy, entropy and free energy of activation were recorded as 85.75, −0.1354 and 156.59 kJ mol⁻¹ respectively at the experimental conditions for maximum depolymerization of polyamide waste. The thermodynamic equilibrium constant for this hydrolysis reaction was found to be 2.3 × 10⁻¹⁶.     

Emission inventory of deca-brominated diphenyl ether (DBDE) in Japan

Atmospheric emissions of deca-brominated diphenyl ether (DBDE) in Japan were estimated based on the material flow of DBDE products and their emission factors. In 2002, the demand for DBDE in Japan was 2200 ton/year and the stock level was about 60 000 ton. The DBDE flow into the waste stream was estimated to be about 6000 ton/year and the flow out through second-hand product exports was more than 700 ton/year. Home appliance recycling facilities dismantle and crush domestic wastes containing about 600 ton of DBDE annually. Material recycling of crushed plastics is not commonly practiced as yet. Emission factors from plastics processing (2 × 10⁻⁹–1 × 10⁻⁷), textile processing (9 × 10⁻⁷), home appliance recycling (8 × 10⁻⁹–5 × 10⁻⁶), and waste incineration (1 × 10⁻⁷–2 × 10⁻⁶) were estimated using field measurement data. The DBDE emission rate through house dust during the service life of final products (2 × 10⁻⁷–9 × 10⁻⁷ per year) was estimated using the DBDE concentration in dust and the amount of dust in used televisions. Emission factors from previous studies were also used. The estimated total DBDE emission was 170–1800 kg/year. These results suggest the necessity of characterizing emissions during the service life of products, which is essential information for formulating an appropriate e-waste recycling strategy.     

Construction and evaluation of simulated pilot scale landfill lysimeter in Bangladesh

This research concentrates the design, construction and evaluation of simulated pilot scale landfill lysimeter at KUET campus, Khulna, Bangladesh. Both the aerobic and anaerobic conditions having a base liner and two different types of cap liner were simulated. After the design of a reference cell, the construction of landfill lysimeter was started in January 2008 and completed in July 2008. In all construction process locally available civil construction materials were used. The municipal solid waste (MSW) of 2800–2985 kg having the total volume of 2.80 m³ (height 1.6 m) and moisture content of 65% was deposited in each lysimeter by applying required compaction energy. In contrast, both the composition in terms of methane (CH₄), carbon dioxide (CO₂) and oxygen (O₂) as well as the flow rate of landfill gas (LFG) generated from MSW in landfill lysimeter were measured and varied significantly in relation to the variation of lysimeter operational condition. Moreover, anaerobic lysimeter-C shows the highest composition of LFG in compare to the anaerobic lysimeter-B due to the providing of lower compaction of cap liner in anaerobic lysimeter-C. Here, it is interesting to note that in absence of compacted clay liner (CCL) and hence percolation of rainwater that facilitates rapid degradation of MSW in aerobic lysimeter-A has resulted in the highest settlement than that of anaerobic landfill lysimeter-B and C. Moreover, in case of anaerobic lysimeter-B and C, the leachate generation was lower than that of aerobic lysimeter-A due to the providing of cap liner in anaerobic lysimeter-B and C, played an important role to reduce the percolation of rainwater. The study also reveals that the leachate pollution index (LPI) has decreased in relation to the increasing of elapsed period as well as the LPI for collection system of aerobic lysimeter-A was higher than that of the collection system of anaerobic lysimeter-B and C. Finally, it can be depicted that LPI for lysimeter was significantly high and proper treatment will be necessary before discharging the lysimeter leachate into the water bodies.     

Fate of saline ions in a planted landfill site with leachate recirculation

Recirculation of leachate on a covered landfill site planted with willows or other highly evapotranspirative woody plants is an inexpensive option for leachate management. In our study, a closed landfill leachate recirculation system was established on a rehabilitated municipal solid waste landfill site with planted landfill cover. The main objective of the study was to evaluate the sustainability of the system with regard to high hydraulic loads of the landfill leachate on the landfill cover and high concentrations of saline ions, especially potassium (K⁺), sodium (Na⁺) and chloride (Cl^?), in leachate.The results of intensive monitoring, implemented during May 2004 and September 2007, including leachate, soil and plant samples, showed a high sustainability of the system regarding saline ions with the precipitation regime of the studied region. Saline ion concentrations in leachates varied between 132 and 2592 mg Cl^? L^?1, 69 and 1310 mg Na⁺ L^?1 and between 66 and 2156 mg K⁺ L^?1, with mean values of 1010, 632 and 686 mg L^?1, respectively. Soil salinity, measured as soil electrical conductivity (EC), remained between 0.17 and 0.38 mS cm^?1 at a depth between 0 and 90 cm. An average annual precipitation of 1000 mm provided sufficient leaching of saline ions, loaded by irrigation with landfill leachate, from the soil of the landfill cover and thus prevented possible salinity shocks to the planted willows.     

Biohydrogen using leachate from an industrial waste landfill as inoculum

Since hydrogen is a renewable energy source, biohydrogen has been researched in recent years. However, data on hydrogen fermentation by a leachate from a waste landfill as inoculum are scarce. We investigated hydrogen production using a leachate from an industrial waste landfill in Kanagawa Prefecture. The results showed no methane gas production, and the leachate was a suitable inoculum for hydrogen fermentation. The maximum H₂ yield was 2.67 mol of H₂ per mol of carbohydrate added, obtained at 30°C and an initial pH of 7. The acetate and butyrate production was significant when the H₂ yield was higher. Oxidation–reduction potential analysis of the culture suggested that hydrogen-producing bacteria in the leachate were facultative anaerobic. Scanning electron microscope observations revealed that the hydrogen-producing bacteria comprised bacilli about 2 μm in length.     

Sustainable sanitary landfills for neglected small cities in developing countries: The semi-mechanized trench method from Villanueva,Honduras

Open dumping is the most common practice for the disposal of urban solid wastes in the least developed regions of Africa, Asia and Latin America. Sanitary landfill design and operation has traditionally focused on large cities, but cities with fewer than 50,000 in population can comprise from 6% to 45% of a given country’s total population. These thousands of small cities cannot afford to operate a sanitary landfill in the way it is proposed for large cities, where heavy equipment is used to spread and compact the waste in daily cells, and then to excavate, transport and apply daily cover, and leachate is managed with collection and treatment systems. This paper presents an alternative approach for small cities, known as the semi-mechanized trench method, which was developed in Villanueva, Honduras. In the semi-mechanized trench method a hydraulic excavator is used for 1–3 days to dig a trench that will last at least a month before it is filled with waste. Trucks can easily unload their wastes into the trench, and the wastes compact naturally due to semi-aerobic biodegradation, after which the trenches are refilled and covered. The exposed surface area is minimal since only the top surface of the wastes is exposed, the remainder being covered by the sides and bottom of the trench. The surplus material from trench excavation can be valorized for use as engineering fill onsite or off. The landfill in Villanueva has operated for 15 years, using a total land area of approximately 11 ha for a population that grew from 23,000 to 48,000, with a land requirement of 0.2 m²/person year, a cover to waste ratio of 0.2, and an estimated soil surplus of 298,000 m³ that is valorized and used onsite. The landfill has been operated solely by the municipality with an operational cost in 2010 estimated at US$4.60 per ton. A modified water balance analysis at Villanueva shows negligible leachate generation from covered trenches and 700 m³/yr (60 m³/ha yr) from the two open trenches required for daily operation. If the site were an open dump, however, leachate generation is estimated to be 3900 m³/ha yr and contaminated runoff 5000 m³/ha yr. A simple model used to estimate dilution of generated leachate based on groundwater flow data and aquifer stratigraphy suggests that the leachate will be diluted by a factor of 0.01 in the aquifer. Leachate contaminants will not accumulate because the aquifer discharges to the Ulua River 2 km south of the landfill. While not suitable for all sites, the Villanueva method nevertheless serves as an excellent example of how a small city landfill with natural compaction of waste and attenuation of leachate can be sustainably operated.     

Developments to a landfill processes model following its application to two landfill modelling challenges

The landfill model LDAT simulates the transport and bio-chemical behaviour of the solid, liquid and gas phases of waste contained in a landfill. LDAT was applied to the LMC1 and LMC2 landfill modelling challenges held in 2009 and 2011. These were blind modelling challenges with the model acting in a predictive mode based on limited early time sections of full datasets. The LMC1 challenge dataset was from a 0.34 m deep 0.48 m diameter laboratory test cell, and the LMC2 dataset was from a 55 m × 80 m 8 m deep landfill test cell which formed part of the Dutch sustainable landfill research programme at Landgraaf in the Netherlands. The paper describes developments in LDAT arising directly from the experience of responding to the two challenges, and discusses the model input and output data obtained from a calibration using the full datasets.The developments include the modularisation of the model into a set of linked sub-models, the strategy for converting conventional waste characteristics into model input parameters, the identification of flexible degradation pathways to control the CO₂:CH₄ ratio, and the application of a chemical equilibrium model that includes a stage in which the solid waste components dissolve into the leachate.     

Design of top covers supporting aerobic in situ stabilization of old landfills – An experimental simulation in lysimeters

Landfill aeration by means of low pressure air injection is a promising tool to reduce long term emissions from organic waste fractions through accelerated biological stabilization. Top covers that enhance methane oxidation could provide a simple and economic way to mitigate residual greenhouse gas emissions from in situ aerated landfills, and may replace off-gas extraction and treatment, particularly at smaller and older sites. In this respect the installation of a landfill cover system adjusted to the forced-aerated landfill body is of great significance. Investigations into large scale lysimeters (2 × 2 × 3 m) under field conditions have been carried out using different top covers including compost materials and natural soils as a surrogate to gas extraction during active low pressure aeration. In the present study, the emission behaviour as well as the water balance performance of the lysimeters has been investigated, both prior to and during the first months of in situ aeration. Results reveal that mature sewage sludge compost (SSC) placed in one lysimeter exhibits in principle optimal ambient conditions for methanotrophic bacteria to enhance methane oxidation. Under laboratory conditions the mature compost mitigated CH₄ loadings up to 300 l CH₄/m² d. In addition, the compost material provided high air permeability even at 100% water holding capacity (WHC). In contrast, the more cohesive, mineral soil cover was expected to cause a notably uniform distribution of the injected air within the waste layer. Laboratory results also revealed sufficient air permeability of the soil materials (TS-F and SS-Z) placed in lysimeter C. However, at higher compaction density SS-Z became impermeable at 100% WHC.Methane emissions from the reference lysimeter with the smaller substrate cover (12–52 g CH₄/m² d) were significantly higher than fluxes from the other lysimeters (0–19 g CH₄/m² d) during in situ aeration. Regarding water balance, lysimeters covered with compost and compost-sand mixture, showed the lowest leachate rate (18–26% of the precipitation) due to the high water holding capacity and more favourable plant growth conditions compared to the lysimeters with mineral, more cohesive, soil covers (27–45% of the precipitation).On the basis of these results, the authors suggest a layered top cover system using both compost material as well as mineral soil in order to support active low-pressure aeration. Conventional soil materials with lower permeability may be used on top of the landfill body for a more uniform aeration of the waste due to an increased resistance to vertical gas flow. A compost cover may be built on top of the soil cover underlain by a gas distribution layer to improve methane oxidation rates and minimise water infiltration. By planting vegetation with a high transpiration rate, the leachate amount emanating from the landfill could be further minimised. The suggested design may be particularly suitable in combination with intermittent in situ aeration, in the later stage of an aeration measure, or at very small sites and shallow deposits. The top cover system could further regulate water infiltration into the landfill and mitigate residual CH₄ emissions, even beyond the time of active aeration.     

The performance of Electro-Fenton oxidation in the removal of coliform bacteria from landfill leachate

Leachate pollution is one of the main problems in landfilling. Researchers have yet to find an effective solution to this problem. The technology that can be used may differ based on the type of leachate produced. Coliform bacteria were recently reported as one of the most problematic pollutants in semi-aerobic (stabilized) leachate. In the present study, the performance of the Electro-Fenton process in removing coliform from leachate was investigated. The study focused on two types of leachate: Palau Borung landfill leachate with low Coliform content (200 MPN/100 m/L) and Ampang Jajar landfill leachate with high coliform content (>24 × 10⁴ MPN/100 m/L). Optimal conditions for the Electro-Fenton treatment process were applied on both types of leachate. Then, the coliform was examined before and after treatment using the Most Probable Number (MPN) technique. Accordingly, 100% removal of coliform was obtained at low initial coliform content, whereas 99.9% removal was obtained at high initial coliform content. The study revealed that Electro-Fenton is an efficient process in removing high concentrations of pathogenic microorganisms from stabilized leachate.     

Case study of landfill leachate recirculation using small-diameter vertical wells

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m³ of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6 × 10^?8 to 3.6 × 10^?6 m³ s^?1 per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5 × 10^?6 to 4.2 × 10^?4 m s^?1. The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p < 0.025) decomposition.     

Impact of landfill liner time–temperature history on the service life of HDPE geomembranes

The observed temperatures in different landfills are used to establish a number of idealized time–temperature histories for geomembrane liners in municipal solid waste (MSW) landfills. These are then used for estimating the service life of different HDPE geomembranes. The predicted antioxidant depletion times (Stage I) are between 7 and 750 years with the large variation depending on the specific HDPE geomembrane product, exposure conditions, and most importantly, the magnitude and duration of the peak liner temperature. The higher end of the range corresponds to data from geomembranes aged in simulated landfill liner tests and a maximum liner temperature of 37 °C. The lower end of the range corresponds to a testing condition where geomembranes were immersed in a synthetic leachate and a maximum liner temperature of 60 °C. The total service life of the geomembranes was estimated to be between 20 and 3300 years depending on the time–temperature history examined. The range illustrates the important role that time–temperature history could play in terms of geomembrane service life. The need for long-term monitoring of landfill liner temperature and for geomembrane ageing studies that will provide improved data for assessing the likely long-term performance of geomembranes in MSW landfills are highlighted.     

Comparing field investigations with laboratory models to predict landfill leachate emissions

Investigations into laboratory reactors and landfills are used for simulating and predicting emissions from municipal solid waste landfills. We examined water flow and solute transport through the same waste body for different volumetric scales (laboratory experiment: 0.08 m³, landfill: 80,000 m³), and assessed the differences in water flow and leachate emissions of chloride, total organic carbon and Kjeldahl nitrogen. The results indicate that, due to preferential pathways, the flow of water in field-scale landfills is less uniform than in laboratory reactors. Based on tracer experiments, it can be discerned that in laboratory-scale experiments around 40% of pore water participates in advective solute transport, whereas this fraction amounts to less than 0.2% in the investigated full-scale landfill. Consequences of the difference in water flow and moisture distribution are: (1) leachate emissions from full-scale landfills decrease faster than predicted by laboratory experiments, and (2) the stock of materials remaining in the landfill body, and thus the long-term emission potential, is likely to be underestimated by laboratory landfill simulations.     

Laboratory alteration of gypsiferous materials below a landfill

Some urban solid waste landfill sites in Spain are located on geological substrates of gypsiferous lithology. Although this type of substrate is assumed to be of low permeability, it can develop secondary pores by dissolution and, under favourable environmental conditions, form a karstic system that may pose serious geotechnical problems in the medium and long term. The purpose of this work was to study alterations caused by selective tests in various sections of a gypsum lithological column obtained from the Colmenar de Oreja landfill site (Spain). The tests were used to assess the influence of individual environmental factors and involved the addition of milli-RO water, solutions containing a 1%, 5% or 10% concentration of landfill leachate, and 2, 5, 10 and 15 mg l^?1 solutions of NaCl in successive immersion–drying cycles at ?15, 20 or 60 °C. Differences in alterability between the six studied segments of the lithological column were found to be due to differences in lutite content, specific crystal habit and type of cement. Segments with specular gypsum were the strongest in the tests, while the segment with the highest amount of detrital materials was the most responsive to temperature and moisture changes. The treatments that produce greater alterations are those that contain only milli-RO water.     

Environmental impact assessment of leachate recirculation in landfill of municipal solid waste by comparing with evaporation and discharge (EASEWASTE)

In some arid regions where landfill produces minimal amount of leachate, leachate recirculation is suggested as a cost-effective option. However, its long-term impacts to environment remain disputed. For the purpose of revealing the environmental impacts of leachate recirculation in landfill, four scenarios were modeled using EASEWASTE, comparing the strategies of leachate recirculation (with or without gas management), evaporation and discharge. In the current situation (Scenario A), a total of 280 t of waste was generated and then transported to a conventional landfill for disposal. A number of contaminants derived from waste can be stored in the landfill for long periods, with 11.69 person equivalent (PE) for stored ecotoxicity in water and 29.62 PE for stored ecotoxicity in soil, considered as potential risks of releasing to the environment someday. Meanwhile, impacts to ecotoxicity and human toxicity in surface water, and those to groundwater, present relatively low levels. In Scenario B, leachate evaporation in a collecting pool has minimal impacts on surface water. However, this strategy significantly impacts groundwater (1055.16 PE) because of the potential infiltration of leachate, with major contaminants of As, ammonia, and Cd. A number of ions, such as Cl^?, Mg²⁺, and Ca²⁺, may also contaminate groundwater. In Scenario C, the direct discharge of leachate to surface water may result in acidification (2.71 PE) and nutrient enrichment (2.88 PE), primarily attributed to soluble ammonia in leachate and the depositional ammonia from biogas. Moreover, the direct discharge of leachate may also result in ecotoxicity and human toxicity via water contaminated by heavy metals in leachate, with 3.96 PE and 11.64 PE respectively. The results also show that landfill gas is the main contributor to global warming and photochemical ozone formation due to methane emission. In Scenario D, landfill gas flaring was thus be modeled and proven to be efficient for reducing impacts by approximately 90% in most categories, like global warming, photochemical ozone formation, acidification, nutrient enrichment, ecotoxicity, and human toxicity. Therefore, leachate recirculation is considered a cost-effective and environmentally viable solution for the current situation, and landfill gas treatment is urgently required. These results can provide important evidence for leachate and gas management of landfill in arid regions.     

Steel slags in a landfill top cover – Experiences from a full-scale experiment

A full scale field study has been carried out in order to test and evaluate the use of slags from high-alloy steel production as the construction materials for a final cover of an old municipal landfill. Five test areas were built using different slag mixtures within the barrier layer (liner). The cover consisted of a foundation layer, a liner with a thickness of 0.7 m, a drainage layer of 0.3 m, a protection layer of 1.5 m and a vegetation layer of 0.25 m. The infiltration varied depending on the cover design used, mainly the liner recipe but also over time and was related to seasons and precipitation intensity. The test areas with liners composed of 50% electric arc furnace (EAF) slag and 50% cementitious ladle slag (LS) on a weight basis and with a proper consistence of the protection layer were found to meet the Swedish infiltration criteria of ?50 l (m² a)^?1 for final covers for landfills for non-hazardous waste: the cumulative infiltration rates to date were 44, 19 and 0.4 l (m² a)^?1 for A1, A4 and A5, respectively. Compared to the precipitation, the portion of leachate was always lower after the summer despite high precipitation from June to August. The main reason for this is evapotranspiration but also the fact that the time delay in the leachate formation following a precipitation event has a stronger effect during the shorter summer sampling periods than the long winter periods. Conventional techniques and equipment can be used but close cooperation between all involved partners is crucial in order to achieve the required performance of the cover. This includes planning, method and equipment testing and quality assurance.     

Effects of leachate accumulation on landfill stability in humid regions of China

Leachate levels are important to landfill stability and safety. High leachate or water levels often lead to landfill instability, which can cause accidents. Here a case study of a landfill located in a humid region of southern China is presented. Leachate distribution and quality were systematically analyzed, and the effect of leachate level on waste-mass stability was assessed. Boreholes were drilled in the field, samples were analyzed in the laboratory, and a simulation was performed. In addition, the safety and stability of the landfill was evaluated. The leachate level in the landfill was 9–19 m, which was higher than the top of the dam crest (8–20 m). Leachate accounted for more than 1/4 of the total landfill storage capacity. The contaminant concentration of the leachate samples collected directly from the waste body was very high, with large variation among the samples. The mean concentrations of NH₃–N, BOD, and COD from the waste body were 5404, 14,136, and 22,691 mg/L, nearly 2.7, 2.4, and 1.8 times the mean concentrations in the leachate pond, respectively. Three series of shear strength parameters were used in a slope stability analysis, and a limit equilibrium method was used to calculate the factor of safety (Fs). The analysis showed that Fs could be affected by potential anisotropy in the shear strength of the waste. The minimum values of Fs corresponding to series I were 1.84 and 1.17 for units ? and II, respectively. The Fs value of unit II was significantly lower than the safe design value (1.25). In addition, Fs decreased with increase in the normalized height of the leachate level, h/H, where h is the height of the leachate mound and H is the maximum thickness of the landfill. If the h/H values of units I and II are kept below 50% and 40%, respectively, a safe design value of 1.25 for Fs can be guaranteed. Therefore, some measures to prevent risk should be considered.