Compositions of Particles from Selected Sources in Philadelphia for Receptor Modeling Applications

As a part of a receptor model study of the Philadelphia, PA atmosphere, particulate samples were collected from seven air pollution sources in the area: two oil-fired power plants, a coal-fired power plant, a fluidized catalytic cracker, a refuse incinerator, a secondary aluminum smelter and an antimony ore roaster. Samples were collected In two size fractions with a dilution source sampler connected to a modified dichotomous sampler. Masses of collected material were determined gravlmetrlcally. Samples were analyzed for elements by x-ray fluorescence followed by Instrumental neutron activation analysis of some samples. Other samples were analyzed by chemical methods for volatile and nonvolatile carbon, SO₄ ^2? and NH₄ ⁺. Data are presented for up to 46 elements and species on fine (<2.5-μm aerodynamic equivalent diameter) and coarse (2.5 μm < diam < 7-10 μm) particles from each source. Although the data were collected for use in Philadelphia, they should be of value for receptor modeling of other areas having similar sources. The most unexpected results were the large amounts of rare earth elements on particles from the catalytic cracker (e.g., 0.31 percent La In fine fraction) and the oil-fired power plants (120 and 420 ppm La in fine fraction). Substantial amounts of primary SO₄ ^2? are released from the oil-fired plants, the SO₄ ^2? concentrations accounting for 40-45 percent of the fine particulate mass.     

Life Cycle Assessment of Fuel Selection for Power Generation in Taiwan

Abstract

Life cycle assessment (LCA) was applied to performance data from 1997–2002 to evaluate the environmental impacts of the energy input, airborne emission, waterborne emission, and solid waste inventories for Taiwan’s electric power plants. Eco-indicator 95 was used to compare the differences among the generation processes and fuel purification. To better understand the environmental trends related to Taiwan’s electric power industry, three fuel scenarios were selected for LCA system analysis. Results indicate that there are differences in characteristic environmental impact among the 13 power plants. Scenario simulation provided a basis for minimizing environmental impacts from fuel selection targets. Fuel selection priority should be a gas-fired combined cycle substituted for a coal-fired steam turbine to be more environmentally friendly, particularly in the areas of the greenhouse effect, acidification, winter smog, and solid waste. Furthermore, based purely on economic and environmental criteria, it is recommended that the gas-fired combined cycle be substituted for the oil-fired steam turbine.     

Sulfur Concentrations in Plant Foliage and Related Effects

Sulfur Is an essential element for plants and is normally taken up from soil In the sulfate form. S0₂ absorbed from the air also can supply S for plant nutrition. Plants are therefore dependent on an optimum S content, but deficiencies or excesses can result in deleterious effects. The Phytotoxicology Section has conducted numerous assessment surveys in rural, urban, or industrial locations in Ontario to determine the concentrations of S in plants and related effects. During the ten year period, 1968 to 1977, about 50,000 samples of vegetation and soil were collected and analyzed for S concentrations. The results of these analyses were examined with respect to natural background concentrations of S in foliage of 33 different species, and effects observed on plant life associated with excess concentrations of S. For example, in one situation 0.35% sulfur in foliage of trembling aspen trees was found to be the threshold level for injury to occur. Some of the industries surveyed for the degree and extent of S effects in their vicinity included pulp mills, power plants, iron concentrators, and gold, nickel, and copper smelters. In interpreting the results of S analyses in plant foliage for diagnostic purposes, consideration should be given also to the geographical location, the stage of growth of the plant, the relation of visible injuries to pollutant or biological causes, the S content of the soil, and S0₂ emission data for the area.     

The persistence of insecticidal chemicals in soils treated with granular formulations of aldicarb and their uptake by potato plants

Abstract

Potatoes were grown in Plainfield sand and muck treated, in furrow, with aldicarb (Temik 15G, 3.36 kg Al/ha). .Soils were contained in 2 m^z field plots and had not been treated previously with pesticides. Soil, seed pieces, foliage and tubers were analyzed for the insecticide and its sulfoxide and sulfone metabolites during the 12 wk following planting. The disappearance of aldicarb from the soil was accompanied by partial conversion to the sulfoxide and sulfone. After increasing rapidly during the first 2 wk, the aldicarb concentration in the seed piece declined and a similar concentration of aldicarb sulfoxide accumulated which subsequently slowly disappeared. Aldicarb sulfoxide was the major insecticidal material in the new foliage. High initial concentrations, observed at 3–4 wk, declined by about 90% after 6 wk. Aldicarb sulfoxide residues of 2–4 ppm in the first new tubers at 6 wk declined by 90% by 12 wk. Potatoes were also grown under greenhouse conditions in Plainfield sand treated with Temik 10G at rates equivalent to 1.68, 3.36 and 6.72 kg Al/ha. Maximum aldicarb sulfoxide concentrations in soil, seed piece and foliage increased with application rate. The sulfoxide was much more persistent in the soil and foliage than in the field experiment indicating the importance of environmental factors to its behaviour in both soil and potato plants.     

Product Guide/1980

Trace element concentrations of the lichen, Flavoparmelia caperata, were determined by neutron activation analysis before and after stringent participate controls were employed in an industrialized section of the Ohio River Valley; Initial studies in 1973 showed elevated concentrations of arsenic, cobalt, iron, vanadium, and titanium in lichens collected near coalfired power plants. Elevated values for cerium, chromium, and lanthanum were found in samples near a ferro-alloys foundry. A repeat study in 1987 demonstrated that lichen trace element concentrations were much lower after improved particulate controls were installed on the power plants and ferro-alloys foundry.     

Characterization of Particulates from Power Plants

The emphasis on participate control from industrial processes has been shifted recently towards fine particulates, having diameters less than 3 microns. There exists an urgent need for more scientific information of fine particle characterization.^1,2 Coal and oil fired power plants are among the largest anthropogenic point sources of particulate matter.³ Limited knowledge is available on particle size distribution and trace metal composition in power plant emissions.^4-7 The morphological properties of particle emissions have been largely neglected. In this report we present some information on particle characteristics for an oil-fired and coal-fired power plant.     

Air pollution assessment based on elemental concentration of leaves tissue and foliage dust along an urbanization gradient in Vienna

Foliage dust contains heavy metal that may have harmful effects on human health. The elemental contents of tree leaves and foliage dust are especially useful to assess air environmental pollution. We studied the elemental concentrations in foliage dust and leaves of Acer pseudoplatanus along an urbanization gradient in Vienna, Austria. Samples were collected from urban, suburban and rural areas. We analysed 19 elements in both kind of samples: aluminium, barium, calcium, copper, iron, potassium, magnesium, sodium, phosphor, sulphur, strontium and zinc. We found that the elemental concentrations of foliage dust were significantly higher in the urban area than in the rural area for aluminium, barium, iron, lead, phosphor and selenium. Elemental concentrations of leaves were significantly higher in urban than in rural area for manganese and strontium. Urbanization changed significantly the elemental concentrations of foliage dust and leaves and the applied method can be useful for monitoring the environmental load.     

The persistence of insecticidal chemicals in soils treated with granular formulations of disulfoton and their uptake by potato plants

Abstract

Potatoes were grown from cut seed in Plainfield sand treated in‐furrow with disulfoton (Di‐Syston 15G, 3.36 kg Al/ha) in 1983 and from whole seed in similarly treated loam in 1991. Soils were contained in 2 m² field plots. Soil, seed potato and foliage were analyzed for the insecticide and its sulfoxide and sulfone metabolites during the 8–12 wk following planting. Disulfoton disappeared at different rates from the two soils (k_sand=0.024 day^‐1, k_loam=0.056 day^‐1) with partial conversion to the sulfoxide and sulfone in both. Larger quantities of the three insecticidal components were absorbed by the seed potato in the cut‐seed/sand combination. The relative amounts of these components in the seed potato also differed between treatments with disulfoton being the largest component of the cut‐seed/sand and smallest in the whole‐seed/loam. Disulfoton sulfoxide and sulfone were the major insecticidal components of the foliage and concentrations in the initial foliage (each ca. 10 ppm) were similar for both treatments. Sulfoxide concentrations in the foliage decreased more rapidly than the sulfone and the decrease in concentration of each of the components was similar for the two treatments.     

Air Quality Impact of the Coal-Fired Power Plants in the Northern Passageway of the China West-East Power Transmission Project

Abstract

This paper analyzes the air quality impacts of coal-fired power plants in the northern passageway of the West-East Power Transmission Project in China. A three-layer Lagrangian model called ATMOS, was used to simulate the spatial distribution of incremental sulfur dioxide (SO₂) and coarse particulate matter (PM₁₀) concentrations under different emission control scenarios. In the year 2005, the emissions from planned power plants mainly affected the air quality of Shanxi, Shaanxi, the common boundary of Inner Mongolia and Shanxi, and the area around the boundary between Inner Mongolia and Ningxia. In these areas, the annually averaged incremental SO₂ and PM₁₀ concentrations exceed 2 and 2.5 µg/m3, respectively. The maximum increases of the annually averaged SO₂ and PM₁₀ concentrations are 8.3 and 7.2 µg/m³, respectively, which occur around Hancheng city, near the boundary of the Shaanxi and Shanxi provinces. After integrated control measures are considered, the maximum increases of annually averaged SO₂ and PM₁₀ concentrations fall to 4.9 and 4 µg/m³, respectively. In the year 2010, the areas affected by planned power plants are mainly North Shaanxi, North Ningxia, and Northwest Shanxi. The maximum increases of the annually averaged SO₂ and PM₁₀ concentrations are, respectively, 6.3 and 5.6 µg/m³, occurring in Northwest Shanxi, which decline to 4.4 and 4.1 µg/m³ after the control measures are implemented. The results showed that the proposed power plants mainly affect the air quality of the region where the power plants are built, with little impact on East China where the electricity will be used. The influences of planned power plants on air quality will be decreased greatly by implementing integrated control measures.     

Foliar and ground deposits of fenitrothion following aerial application over a plantation forest

Abstract

Spray deposits were measured on spruce foliage at tree canopy level and on glass plates at ground level, after aerial application of an emulsion formulation of fenitrothion at the rate of 0.21 kg AI in 1.46 L per ha over a 16 ha plot in a plantation forest. Fenitrothion deposits were quantified by gas‐liquid chromatography. A wide variation was observed in deposits on foliage and at the forest floor. Deposits were relatively higher on foliar samples collected from the upwind side of a tree canopy than those on the downwind side. Similarly, the glass plate placed under a tree on the upwind side received relatively higher deposit than the one on the downwind side. However, the glass plates placed in the adjacent forest openings collected markedly higher deposits. Results clearly indicate filtration of the spray droplets by canopy foliage. Assessment of the average deposit of fenitrothion at ground level (mean deposit from all sampling locations) indicated that ca. 19.4% of the applied material reached the forest floor. Within a sampling station, correlation was poor between foliar depsits and those on glass plates under the same trees or in nearby clearings. Analysis of fenitrothion deposits on foliage collected at 1 and 2 h after application indicated that the droplets took, more than 1 h for deposition on the tree canopy. On the other hand, deposition on the glass plates at ground level appeared to be practically complete within 1 h post‐treatment. This was attributed to the higher sedimentation velocities of the larger droplets which tend to travel faster to the floor level than the smaller droplets which float for a longer period near the tree canopy.     

Air Quality Impacts of Distributed Energy Resources Implemented in the Northeastern United States

Abstract

Emissions from the potential installation of distributed energy resources (DER) in the place of current utility-scale power generators have been introduced into an emissions inventory of the northeastern United States. A methodology for predicting future market penetration of DER that considers economics and emission factors was used to estimate the most likely implementation of DER. The methodology results in spatially and temporally resolved emission profiles of criteria pollutants that are subsequently introduced into a detailed atmospheric chemistry and transport model of the region. The DER technology determined by the methodology includes 62% reciprocating engines, 34% gas turbines, and 4% fuel cells and other emerging technologies. The introduction of DER leads to retirement of 2625 MW of existing power plants for which emissions are removed from the inventory. The air quality model predicts maximum differences in air pollutant concentrations that are located downwind from the central power plants that were removed from the domain. Maximum decreases in hourly peak ozone concentrations due to DER use are 10 ppb and are located over the state of New Jersey. Maximum decreases in 24-hr average fine particulate matter (PM_2.5) concentrations reach 3 μg/m3 and are located off the coast of New Jersey and New York. The main contribution to decreased PM_2.5 is the reduction of sulfate levels due to significant reductions in direct emissions of sulfur oxides (SO_x) from the DER compared with the central power plants removed. The scenario presented here represents an accelerated DER penetration case with aggressive emission reductions due to removal of highly emitting power plants. Such scenario provides an upper bound for air quality benefits of DER implementation scenarios.     

Lettuce cationic nutrition and yield, and soil chemical characteristics as affected by vanadium application to leaves or soils

Lettuce plants (Lactuca sativa, L., cv. 'trocadero') were grown in pots filled with an Alfisol Udalf or an Andisol Udand soil, under greenhouse conditions. Treatments consisted of adding vanadium to soils (0, 100, 250, 500 and 10001mg1kg₁ or as foliar sprays (0, 10, 25, 50, and 1001mg11₁. Soil chemical characteristics, the cationic nutrition of lettuce and their yields were assessed. No relation was found among vanadium treatments and soil pH, organic matter, or available Ca, Mg, and K. Vanadium added to soils increased available vanadium in the soil, but foliar sprays did not. Treatments did not influence foliar K, Ca, Mg, Cu, Mn and Zn concentrations, and only foliar iron levels showed a correlation with available vanadium in the soils treated with this heavy metal. Higher concentrations of vanadium added to soil or in foliar sprays significantly increased the vanadium content of the lettuces, but they did not affect the yields of either fresh or dry matter.     

The effect of multiple soil applications of disulfoton on enhanced microbial degradation in soil and subsequent uptake of insecticidal chemicals by potato plants

Abstract

Potatoes were grown during 1992 in 2 m² plots of loam which had received 1, 2 or 3 annual treatments of Di‐Syston 15G, equivalent to 3.36 kg AI/ha, in furrow at planting. The presence of enhanced degradative activity to the sulfoxide and sulfone metabolites of disulfoton in the soil treated in the previous two years was confirmed by laboratory tests prior to the 1992 treatments. Soil, seed potato and foliage from the three treatments were analyzed for disulfoton and its sulfoxide and sulfone metabolites for 12 wk following planting/treatment. Disulfoton was the major insecticidal component of the soil, a minor component of the seed piece and was not detected (<0.02 ppm) in potato foliage. Disulfoton concentrations in each of the three substrates sampled were similar for the three treatments. Disulfoton sulfoxide and sulfone were the major insecticidal components of the seed piece and foliage. Their maximum concentrations in 1st year soil, seed pieces and foliage were ca. 2x, 2x and 6x, respectively, those measured in the 2nd and 3rd year treatments. The results demonstrate that enhanced microbial degradation of relatively minor insecticidal compounds in the soil can profoundly affect insecticide levels in the plant when these compounds are the major insecticidal components accumulated. The broader implications for crop protection using soil‐applied systemic insecticides are discussed.     

Deposition of aerially sprayed mexacarbate on balsam fir canopy and the forest floor: Relevance to ULV applications

Abstract

Spray deposit patterns were measured on aluminum coils and live balsam fir needles at different canopy heights, following aerial application of mexacarbate (4‐dimethylamino‐3,5‐xylyl N‐methylcarbamate) over a conifer forest in New Brunswick. Droplet size spectra of the spray cloud were determined on cylindrical Kromekote® cards placed at the corresponding crown heights. Ground deposits were collected on cylindrical Kromekote cards, aluminum coils and natural balsam fir foliage placed In forest clearings and under different types of vegetation.

Canopy deposits decreased progressively from the top to the bottom level of the tree crown. This trend was observed on aluminum coils, live fir foliage, and Kromekote cards. Droplet size spectra were similar at all sampling heights of the tree crown, and were comparable to those obtained on the ground cards placed in the forest clearings. Deposits of mexacarbate obtained on ground samplers on the open forest floor were markedly lower than those found at the top canopy but were similar to those at the mid or bottom canopy level. Droplet size spectra and mexacarbate deposits obtained on samplers placed under different types of forest vegetation indicated a selective filtration of the large droplets present in the spray cloud by plant canopies.     

Influence of surfactant concentration on foliar retention of pesticides used in forestry

Abstract

Aqueous tank mixes of permethrin, fenitrothion, Bacillus thuringiensis (B.t.), diflubenzuron (DFB), and glyphosate containing different amounts of Triton® X‐114, a nonionic surfactant, were prepared. Glyphosate formed clear solutions, permethrin and fenitrothion formed emulsions, DFB and B.t provided suspensions. Emulsion stability of permethrin and fenitrothion increased with increasing surfactant level, while the emulsion drop size decreased.

Foliage of white oak, trembling aspen, white spruce and balsam fir were dipped in tank mixes of pesticides (except B.t.) labelled with ¹⁴carbon. The amount of pesticide retained on foliage was determined by liquid scintillation counting. Foliage was also dipped in non‐radioactive B.t. tank mixes, and the protein retained was determined colorimetrically. With all tank mixes, a direct relationship was observed between the mass of liquids retained on foliage and liquid viscosity. In contrast, the amount of pesticide retained was unaffected by viscosity, but was influenced by emulsion drop size. Initially, the amount of pesticide retained on foliage increased with increasing surfactant concentration. Beyond an optimum surfactant level, the emulsion drop sizes were too small and the emulsions became too stable to allow maximum retention of pesticides on foliage. With the glyphosate solutions, however, no optimum surfactant level was indicated because foliar concentrations continued to increase with increasing surfactant levels.     

Influence of additives in the end‐use mixes of tebufenozide on deposition,adhesion and persistence in spruce foliage

Abstract

A commercial flowable formulation of tebufenozide, RH‐5992 2F [N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyl) hydrazine], was diluted with water, water and canola oil, and water and the methyl ester of canola oil, to provide six end‐use mixes with concentrations of 35 and 70 g of active ingredient (Al) litre^‐1. The mixes were applied at 70 and 140 g Al ha^‐1 over white spruce [Picea glauca (Moench) Voss] seedlings in a laboratory spray chamber and foliar concentrations of tebufenozide were determined over a 60‐d period. At intervals of time post‐spray, seedlings were sprayed with monosized droplets of Sunspray®11N as rainfall, and the amount of tebufenozide knocked off from foliage was determined. The potential energy of adhesion (PEA) of the Al particles on the foliage increased with time and varied according to the type of end‐use mix, its viscosity and the dosage sprayed.

The end‐use mixes were applied over white spruce trees under field conditions and persistence of tebufenozide was investigated. DT₅₀ values were influenced by the type of mix and dosage sprayed. Oil‐containing mixes and higher dosages increased the PEA of tebufenozide particles.     

Biochemical and Physiological Detection of Sulfur Dioxide Injury to Pea Plants (Pisum sativum)

Biochemical and physiological experiments were conducted on pea plants (Pisum sativum) continuously exposed in growth chambers to SO₂ gas for 18 days. S0₂ gas concentrations were 0.1, 0.15, and 0.25 ppm. In plants exposed to 0.1 and 0.15 ppm it was clearly demonstrated that there was a greater accumulation of inorganic sulfur, a reduced buffer capacity of the cells relative to H-ions, and a stimulation of glutamate dehydrogenase activity. The only macroscopic symptom seen was slight chlorosis of the older leaves. There was only a slight decrease in fresh and dry weights of these plants compared to the control plants whereas in the group of plants exposed to 0.25 ppm SO₂ foliage necrosis was considerable. In addition, there was a marked reduction in the fresh and dry weights of the latter plants. However, the relationship among accumulated inorganic sulfur, reduced buffer capacity, and increased glutamate dehydrogenase activity as seen for the lower S0₂ concentrations was close. Accordingly, if might be possible to use these three parameters to diagnose S0₂ injury before any significant symptoms appear. In the case of severe SO₂ injury there was a marked increase in glutamine and ammonia concentrations suggesting that these factors in addition to the above could be used in diagnosing severe SO₂ injury. There was no significant difference between plants treated with 0.1 or 0.15 ppm SO₂ and control plants in the contents of K, Ca, P, and N fractions. Therefore, these factors would not be useful in the early detection of SO₂ injury.     

The Fate of Vanadium in an Urban Air Shed: The Lower Delaware River Valley

Vanadium compounds are toxic pollutants which require engineering control in the design stage. In the lower Delaware River Valley, the main sources are presently the combustion of vanadium rich fuel oils and the catalytic processing of high vanadium crudes. These and other Industrial emissions, result in atmospheric vanadium concentrations which have varied from 0.133 μg/m³ to 0.557 μg/m³ between 1958 and 1969. Compounds of vanadium, principally with oxygen and sulfur, are considered. The dominance of oxygen compounds over sulfur compounds as derived from equilibrium data, and the tendency of vanadium oxides to move toward vanadium’s maximum valence of +5, indicate the prevalence of V₂0₅ as the emission compound.     

Distribution and persistence of carbaryl in some terrestrial and aquatic components of a forest environment

Abstract

An oil‐based formulation of carbaryl (1‐naphthyl N‐methyl‐carbamate) (Sevin‐2‐Oil) was applied twice by a fixed‐wing aircraft at a dosage rate of 280 g of A.I./ha/application to a coniferous forest near Allardville, New Brunswick. The highest concentrations of the chemical in fir foliage, litter and forest soil 1 h after application were respectively 4.20, 1.21 and 0.59 ppm (fresh weight). The residues dissipated rapidly and the DT50 values obtained from the depletion curves were 2.3 d for foliage and 1.5 d for litter and soil samples. Very low levels (<0.1 ppm) of carbaryl persisted in foliage and litter beyond the 10 d sampling period. The maximum residue level found in stream water was 0.314 ppm and more than 50% of it had dissipated within 1 h. Low but detectable levels (0.001 ppm) of the chemical persisted in water until the end of the 10 d sampling period. Sediment samples contained a maximum level of 0.04 ppm, which dissipated below the detection limit within 5 h. Brook trout and slimy sculpins captured in the stream 1 d after the spray contained on average about 0.04 ppm of carbaryl and none of it was found in 3 d postspray samples.