Seasonal source-receptor relationships in a petrochemical industrial district over northern Taiwan

This study investigated the relationships between meteorological data, pollution sources, and receptors over northern Taiwan. During the intensive sampling period in summer 1992, the weather was controlled predominantly by a Pacific subtropical high and by Typhoon Mark. During the other intensive sampling period in winter 1993, while a cold frontal system approached Taiwan, the northeasterly winds prevailed most of the time. The local circulation such as land-sea breeze only developed under weak synoptic environment. Particle concentrations and element composition in winter were higher than in summer. This can be attributed to the high convection of air mass, which leads to the vertical dispersion of pollutants in summer. In addition to the subtropical high pressure, typhoons are frequently accompanied with high-wind speeds and unstable weather conditions that also dilute and eliminate the pollutants. In winter, the prevailing northeasterlies might carry pollutants from Midland China. Furthermore, the anticyclone system develops a stagnant condition that easily leads to pollutant accumulation. In this case, the wind direction affected the source contribution of the receptor and the PM10 displays a higher correlation with coarse and fine particulate than meteorological parameters in summer. In addition, the mixing height shows a high correlation with PM10 in winter.     

Laboratory and Field Evaluation of Measurement Methods for One-Hour Exposures to O3, PM25, and CO

ABSTRACT

While researchers have linked acute (less than 12-hr) ambient O₃, PM₂₅, and CO concentrations to a variety of adverse health effects, few studies have characterized short-term exposures to these air pollutants, in part due to the lack of sensitive, accurate, and precise sampling technologies. In this paper, we present results from the laboratory and field evaluation of several new (or modified) samplers used in the “roll-around” system (RAS), which was developed to measure 1-hr O₃, PM₂₅, and CO exposures simultaneously. All the field evaluation data were collected during two sampling seasons: the summer of 1998 and the winter of 1999.

To measure 1-hr O₃ exposures, a new active O₃ sampler was developed that uses two nitrite-coated filters to measure O₃ concentrations. Laboratory chamber tests found that the active O₃ sampler performed extremely well, with a collection efficiency of 0.96 that did not vary with temperature or relative humidity (RH). In field collocation comparisons with a reference UV photometric monitor, the active O₃ sampler had an effective collection efficiency ranging between 0.92 and 0.96 and a precision for 1-hr measurements ranging between 4 and 6 parts per billion (ppb). The limits of detection (LOD) of this method were 9 ppb-hr for the chamber tests and ~16 ppb-hr for the field comparison tests.

PM_2.5 and CO concentrations were measured using modified continuous monitors—the DustTrak and the Langan, respectively. A size-selective inlet and a Nafion dryer were placed upstream of the DustTrak inlet to remove particles with aerodynamic diameters greater than 2.5 um and to dry particles prior to the measurements, respectively. During the field validation tests, the DustTrak consistently reported higher PM_2.5 concentrations than those obtained by the collocated 12-hr PM_{2 5} PEM samples, by approximately a factor of 2. After the DustTrak response was corrected (correction factor of 2.07 in the summer and 2.02 in the winter), measurements obtained using these methods agreed well with R² values of 0.87 in the summer and 0.81 in the winter. The results showed that the DustTrak can be used along with integrated measurements to measure the temporal and spatial variation in PM_{2 5} exposures. Finally, during the field validation tests, CO concentrations measured using the Langan were strongly correlated with those obtained using the reference method when the CO levels were above the LOD of the instrument [~1 part per million (ppm)].     

Comment on “Measuring Air Quality Levels Inexpensively at Multiple Locations by Random Sampling”

ABSTRACT

In order to evaluate the spatial variation of aerosol (particulate matter with aerodynamic diameter ≤10 μm [PM₁₀]) and ozone (O₃) concentrations and characterize the atmospheric conditions that lead to O₃ and PM₁₀-rich episodes in southern Italy during summer 2007, an intensive sampling campaign was simultaneously performed, from middle of July to the end of August, at three ground-based sites (marine, urban, and high-altitude monitoring stations) in Calabria region. A cluster analysis, based on the prevailing air mass backward trajectories, was performed, allowing to discriminate the contribution of different air masses origin and paths. Results showed that both PM₁₀ and O₃ levels reached similar high values when air masses originated from the industrialized continental Europe as well as under the influence of wildfire emissions. Among natural sources, dust intrusion and wildfire events seem to involve a marked impact on the recorded data. Typical fair weather of Mediterranean summer and persisting anticyclone system at synoptic scale were indeed favorable conditions to the arrival of heavily dust-loaded air masses over three periods of consecutive days and more than half of the observed PM₁₀ daily exceedances have been attributed to Saharan dust events. During the identified dust outbreaks, a consistent increase in PM₁₀ levels with a concurrent decrease in O₃ values was also observed and discussed.

IMPLICATIONS In the summertime, the central-southern Mediterranean Basin is heavily affected by Saharan dust outbreaks and wildfire events. A focus on their significant influence on either oxidizing capacity of the atmosphere and air quality over Calabria, southern Italy, was here presented. Similar studies for most regions surrounding the Mediterranean Basin are needed to implement effective emission reduction measures, to prevent apparent air quality parameter exceedances and to define an appropriate health alert system. Because the frequency of these events is expected to increase due to climate change, these studies could even be a valid effort to better understand and characterize such atmospheric variations.     

Codependencies of Reactive Air Toxic and Criteria Pollutants on Emission Reductions

Abstract

It is important to understand the effects of emission controls on concentrations of ozone, fine particulate matter (PM_2.5), and hazardous air pollutants (HAPs) simultaneously, to evaluate the full range of health, ecosystem, and economic effects. Until recently, the capability to simultaneously evaluate interrelated atmospheric pollutants (“one atmosphere” analysis) was unavailable to air quality managers. In this work, we use an air quality model to examine the potential effect of three emission reductions on concentrations of ozone, PM_2.5, and four important HAPs (formaldehyde, acetaldehyde, acrolein, and benzene) over a domain centered on Philadelphia for 12-day episodes in July and January 2001. Although NO_x controls are predicted to benefit PM_2.5 concentrations and sometimes benefit ozone, they have only a small effect on formaldehyde, slightly increase acetaldehyde and acrolein, and have no effect on benzene in the July episode. Concentrations of all pollutants except benzene increase slightly with NO_x controls in the January simulation. Volatile organic compound controls alone are found to have a small effect on ozone and PM_2.5, a less than linear effect on decreasing aldehydes, and an approximately linear effect on acrolein and benzene in summer, but a slightly larger than linear effect on aldehydes and acrolein in winter. These simulations indicate the difficulty in assessing how toxic air pollutants might respond to emission reductions aimed at decreasing criteria pollutants such as ozone and PM_2.5.     

Particulate matter source apportionment in a village situated in industrial region of Central Europe

The bilinear receptor model positive matrix factorization (PMF) was used to apportion particulate matter with an aerodynamic diameter of 1–10 μm (PM_1–10) sources in a village, B?ezno, situated in an industrial region of northern Bohemia in Central Europe. The receptor model analyzed the data sets of 90- and 60-min integrations of PM_1–10 mass concentrations and elemental composition for 27 elements. The 14-day sampling campaigns were conducted in the village in summer 2008 and winter 2010. Also, to ensure seasonal and regional representativeness of the data sets recorded in the village, the spatial-temporal variability of the 24-hr PM₁₀ and PM_1–10 within 2008–2010 in winter and summer across the multiple sites was evaluated. There were statistically significant interseasonal differences of the 24-hr PM data, but not intrasummer or intrawinter differences of the 24-hr PM_1–10 data across the multiple sites. PMF resolved seven sources of PM_1–10. They were high-temperature coal combustion; combustion in local heating boilers; marine aerosol; mineral dust; primary biological/wood burning; road dust, car brakes; and gypsum. The main summer factors were assigned to mineral dust (38.2%) and primary biological/wood burning (33.1%). In winter, combustion factors dominated (80%) contribution to PM_1–10. The conditional probability function (CPF) helped to identified local sources of PM_1–10. The source of marine aerosol from the North Sea and English Channel was indicated by the Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT).

Implications: This is the first application of PMF to highly time/size resolved PM data in Czech Republic. The coarse aerosol fraction, PM_1–10, was chosen with regard to industrial character of the region, sampling site near the coal strip mine and coal power stations. Contrary to expectation, source apportionment did not show dominance of emissions from the coal strip mine. The results will enable local authorities and state bodies responsible for air quality assessment to focus on sources most responsible for air pollution in this industrial region.

Supplemental Materials:?Supplemental materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for (1) details of measurement campaigns; (2) CPF for each of the sources contributing to PM_1–10; (3) factors contribution to PM_1–10 resolved by PMF; (4) diurnal pattern of road dust, car brake factor in summer and winter; (5) trajectories during the marine aerosol episode in winter 2010; and (6) temporal temperature, concentration, and wind speed relationships during the summer 2008 campaign and winter 2010 campaign.     

Multiple comparisons of organic,microbial, and fine particulate pollutants in typical indoor environments: Diurnal and seasonal variations

This study was performed to investigate the possible sources as well as seasonal and diurnal variations of indoor air pollutants in widely used four different environments (house, office, kindergarten, and primary school) in which people spend most of their time. Bioaerosol levels and species, volatile organic compound (VOC) levels, and PM_2.5 (particulate matter with an aerodynamic diameter ≤2.5 μm) levels were determined in different parts of these environments in parallel with outdoor sampling. Air pollution samplings were carried out in each microenvironment during five subsequent days in both winter and summer in Ankara, Turkey. The results indicated that bioaerosol, VOC, and PM_2.5 levels were higher in the winter than in the summer. Moreover, PM_2.5 and bioaerosol levels showed remarkable daily and diurnal variations, whereas a good correlation was found between the VOC levels measured in the morning and in the afternoon. Bacteria levels were, in general, higher than fungi levels. Among the VOCs, toluene was the most predominant, whereas elevated n-hexane levels were also observed in the kindergarten and the primary school, probably due to the frequent wet cleaning during school days. According to factor analysis, several factors were found to be significantly influencing the indoor air quality (IAQ), and amongst them, VOC-based products used indoors ranked first. The overall results indicate that grab sampling in naturally ventilated places may overestimate or underestimate the IAQ due to the inhomogeneous composition of indoor air caused by irregular exchanges with the outdoor air according to the season and/or occupants' habits.

Implications Seasonal and diurnal variations of VOCs, PM_2.5, bioaerosols in house, office, and schools were observed, in which PM_2.5 and bioaeorosols showed marked both intra- and interday variability, but VOCs did not. VOC-containing products were the most common source of air pollutants affecting the indoor air quality. External factors affecting the indoor air quality were season and indirectly ventilation. A grab sample cannot be representative in evaluating the air quality of a naturally ventilated environment precisely.     

Effect of the Fine Fraction of Particulate Matter versus the Coarse Mass and Other Pollutants on Daily Mortality in Santiago,Chile

ABSTRACT

Daily counts of non-accidental deaths in Santiago, Chile, from 1988 to 1996 were regressed on six air pollutants— fine particles (PM_2.5), coarse particles (PM_10–2.5), CO, SO₂, NO₂, and O₃. Controlling for seasonal and meteorological conditions was done using three different models— a generalized linear model, a generalized additive model, and a generalized additive model on previously filtered data. Single- and two-pollutant models were tested for lags of 1-5 days and the average of the previous 2-5 days.

The increase in mortality associated with the mean levels of air pollution varied from 4 to 11%, depending on the pollutants and the way season of the year was considered. The results were not sensitive to the modeling approaches, but different effects for warmer and colder months were found. Fine particles were more important than coarse particles in the whole year and in winter, but not in summer. NO₂ and CO were also significantly associated with daily mortality, as was O₃ in the warmer months. No consistent effect was observed for SO₂. Given particle composition in Santiago, these results suggest that combustion-generated pollutants, especially from motor vehicles, may be associated with increased mortality. Temperature was closely associated with mortality. High temperatures led to deaths on the same day, while low temperatures lead to deaths from 1 to 4 days later.     

Temporal Variations of PM2.5, PM10, and Gaseous Precursors during the 1995 Integrated Monitoring Study in Central California

ABSTRACT

The spatial and temporal distributions of particle mass and its chemical constituents are essential for understanding the source-receptor relationships as well as the chemical, physical, and meteorological processes that result in elevated particulate concentrations in California’s San Joaquin Valley (SJV). Fine particulate matter ₍PM_2.5), coarse particulate matter (PM₁₀), and aerosol precursor gases were sampled on a 3-hr time base at two urban (Bakersfield and Fresno) and two non-urban (Kern Wildlife Refuge and Chowchilla) core sites in the SJV during the winter of 1995–1996.

Day-to-day variations of PM_2.5 and PM₁₀ and their chemical constituents were influenced by the synoptic-scale meteorology and were coherent among the four core sites. Under non-rainy conditions, similar diurnal variations of PM_2.5 and coarse aerosol were found at the two urban sites, with concentrations peaking during the nighttime hours. Conversely, PM_2.5 and coarse aerosol peaked during the morning and afternoon hours at the two non-urban sites. Under rainy and foggy conditions, these diurnal patterns were absent or greatly suppressed.

In the urban areas, elevated concentrations of primary pollutants (e.g., organic and elemental carbons) during the late afternoon and nighttime hours reflected the impact from residential wood combustion and motor vehicle exhaust. During the daytime, these concentrations decreased as the mixed layer deepened. Increases of secondary nitrate and sulfate concentrations were found during the daylight hours as a result of photochemical reactions. At the non-urban sites, the same increases in secondary aerosol concentrations occurred during the daylight hours but with a discernable lag time. Concentrations of the primary pollutants also increased at the non-urban sites during the daytime. These observations are attributed to mixing aloft of primary aerosols and secondary precursor gases in urban areas followed by rapid transport aloft to non-urban areas coupled with photochemical conversion.     

Daily Mortality and Air Pollution in the Netherlands

ABSTRACT

We studied the association of daily mortality with short-term variations in the ambient concentrations of major gaseous pollutants and PM in the Netherlands. The magnitude of the association in the four major urban areas was compared with that in the remainder of the country. Daily cause-specific mortality counts, air quality, temperature, relative humidity, and influenza data were obtained from 1986 to 1994. The relationship between daily mortality and air pollution was modeled using Poisson regression analysis. We adjusted for potential confounding due to long-term and seasonal trends, influenza epidemics, ambient temperature and relative humidity, day of the week, and holidays, using generalized additive models.

Influenza episodes were associated with increased mortality up to 3 weeks later. Daily mortality was significantly associated with the concentration of all air pollutants. An increase in the PM₁₀ concentration by 100 u.g/m³ was associated with a relative risk (RR) of 1.02 for total mortality. The largest RRs were found for pneumonia deaths. Ozone had the most consistent, independent association with mortality. Particulate air pollution (e.g., PM₁₀, black smoke [BS]) was not more consistently associated with mortality than were the gaseous pollutants SO₂ and NO₂. Aerosol SO₄ ^-2, NO₃ ^-, and BS were more consistently associated with total mortality than was PM₁₀. The RRs for all pollutants were substantially larger in the summer months than in the winter months. The RR of total mortality for PM₁₀ was 1.10 for the summer and 1.03 for the winter. There was no consistent difference between RRs in the four major urban areas and the more rural areas.     

Long-term trends and characteristics of visibility in two megacities in southwest China: Chengdu and Chongqing

Visibility is a good indicator of air quality because it reflects the combined influences of atmospheric pollutants and synoptic processes. Trends in visibility and relationships with various factors in Chengdu and Chongqing, two megacities in southwest China, were analyzed using daily data from National Climatic Data Center and the Air Pollution Index (API) of the Ministry of Environmental Protection of China. Average annual visibility during the period of 1973–2010 was 8.1 ± 3.9 in Chengdu and 6.2 ± 4.3 km in Chongqing. PM₁₀ dominates the reported primary pollutants in both cities, although concentrations have decreased from a high of 127.9 and 150 µg m³ before 2005 to 100.4 and 93.5 µg m^?3 in Chengdu and Chongqing, respectively. Low average visibility and extremely high levels of PM10 were observed in winter, whereas relative humidity had irregular and weak seasonal variations. Visibility in both cities has deteriorated in comparison to the 1960s and 1970s, mostly due to the elevation of optical depth caused by anthropogenic pollution.

Correlations and principal component analysis (PCA) were undertaken to determine the key factors affecting visibility. Visibility was only moderately correlated with PM₁₀. In Chengdu, visibility displayed weak correlations with various factors, whereas visibility in Chongqing was most strongly related to relative humidity due to the atmospheric particulates in the region containing more hygroscopic components. PCA results further confirmed that high relative humidity and low wind speed increased the occurrence of low visibility events under high PM₁₀ concentrations. Temperature and pressure, as indicators of weather systems, also played important roles in affecting visibility. Mathematical models of visibility prediction indicated that wind speed had the largest coefficients among all meteorological factors, and reductions in PM₁₀ concentration only led to minor improvements in visibility.

Implications: Long-term data indicates that visibility in Chengdu and Chongqing has been lower than 10 km since the 1970s, and the poor visibility primarily results from anthropogenic pollution. Although PM₁₀ concentrations have decreased consistently to around 100 μg m^?3, trends of visibility have shown no improvement but much fluctuation. Correlation and principal component analysis demonstrate that low visibility in Chengdu is influenced by high relative humidity, while in Chongqing the degrading visibility is related with high relative humidity and pressure and low wind speed under a stable weather system. The results are important to understand the widespread haze event in the two megacities of southwest China.     

Effects of Aerosol Species on Atmospheric Visibility in Kaohsiung City,Taiwan

Abstract

Visibility data collected from Kaohsiung City, Taiwan, for the past two decades indicated that the air pollutants have significantly degraded visibility in recent years. During our study period, the seasonal mean visibilities in spring, summer, fall, and winter were only 5.4, 9.1, 8.2, and 3.4 km, respectively. To ascertain how urban aerosols influence the visibility, we conducted concurrent visibility monitoring and aerosol sampling in 1999 to identify the principal causes of visibility impairments in the region. In this study, ambient aerosols were sampled and analyzed for 11 constituents, including water-soluble ions and carbon materials, to investigate the chemical composition of Kaohsiung aerosols. Stepwise regression method was used to correlate the impact of aerosol species on visibility impairments. Both seasonal and diurnal variation patterns were found from the monitoring of visibility. Our results showed that light scattering was attributed primarily to aerosols with sizes that range from 0.26 to 0.90 μm, corresponding with the wavelength region of visible light, which accounted for ～72% of the light scattering coefficient. Sulfate was a dominant component that affected both the light scattering coefficient and the visibility in the region. On average, (NH₄)₂SO₄, NH₄NO₃, total carbon, and fine particulate matter (PM_2.5)-remainder contributed 53%, 17%, 16%, and 14% to total light scattering, respectively. An empirical regression model of visibility based on sulfate, elemental carbon, and humidity was developed, and the comparison indicated that visibility in an urban area could be properly simulated by the equation derived herein.     

Wintertime and summertime São Paulo aerosol source apportionment study

A detailed aerosol source apportionment study was performed with two sampling campaigns, during wintertime and summertime in the heavily polluted metropolitan area of São Paulo, Brazil. In addition to 12 h fine and coarse mode filter sampling, several real time aerosol and trace gas monitors were used. PM₁₀ was sampled using stacked filter units that collects fine (d<2.5 μm) and coarse (2.5<d<10 μm) particulate matter, providing mass, black carbon (BC) and elemental concentration for each aerosol mode. The concentration of about 20 elements was determined using the particle induce X-ray emission technique. Real time aerosol monitors provided PM₁₀ aerosol mass (TEOM), organic and elemental carbon (Carbon Monitor 5400, R&P) and BC concentration (Aethalometer). A complex system of sources and meteorological conditions modulates the heavy air pollution of the urban area of São Paulo. The boundary layer height and the primary emissions by motor vehicles controls the strong pattern of diurnal cycles obtained for PM₁₀, BC, CO, NO_x, and SO₂. Absolute principal factor analysis results showed a very similar source pattern between winter and summer field campaigns, despite the different locations of the sampling sites of both campaigns, pointing that there are no significant change in the main air pollution sources. The source identified as motor vehicle represented 28% and 24% of the PM_2.5 for winter and summer, respectively. Resuspended soil dust accounted for 25% and 30%. The oil combustion source represented 18% and 21%. Sulfates accounts for 23% and 17% and finally industrial emissions contributed with 5% and 6% of PM_2.5, for winter and summer, respectively. The resuspended soil dust accounted for a large fraction (75–78%) of the coarse mode aerosol mass. Certainly automobile traffic and soil dust are the main air pollution sources in São Paulo. The sampling and analytical procedures applied in this study showed that it is possible to perform a quantitative aerosol source apportionment in a complex urban area such as São Paulo.     

Identification of weather patterns impacting 24-h average fine particulate matter pollution

Methods are presented to extract intra-seasonal meteorological patterns at three scales to explain 24-h fine particulate matter (PM_2.5) pollution events: evolving large-scale meteorological scenarios, synoptic regimes driving diurnal variability near the surface, and localized meteorological triggers. The methods were applied to understand how winter weather conditions impacted PM_2.5 around the San Francisco Bay Area (SFBA). Analyzing data across 12 winters (November–March) ensured robust characterization of the SFBA conditions. SFBA 24-h PM_2.5 exceedances (35 μg m^?3) required several simultaneous characteristics: a ridge of aloft high pressure moving over SFBA, providing weak surface pressure gradients over Central California; persistent easterly flows through SFBA extending vertically to around the 925-hPa pressure level; orographically channeled winds resulting from stability; enhanced nocturnal cooling under clear-sky conditions providing for enhanced drainage flows off the Central California slopes; and at least two consecutive days of these conditions.     

A gas/aerosol air pollutants study over the urban area of Rome using a comprehensive chemical transport model

The aim of this study was to identify areas of potential relevant exposure to pollutants within Rome's urban core. To meet this goal, intensive field campaigns were conducted and simulations were performed, using the flexible air quality regional model (FARM), to study winter and summer pollution episodes. The simulations were performed using a complete emission inventory that included traffic flow model results of the Roman street network to better describe, with respect to the available diffuse national emission inventory, the hourly variation of traffic emissions in the city. The meteorological reconstruction was performed by means of both prognostic and diagnostic models by using experimental data collected during the field campaigns. To evaluate the capability of the FARM model to capture the main features of the selected episodes, a comparison of modelled results against observed air quality data for different pollutants was performed at urban and rural sites. FARM performed well in predicting ozone (O₃) and nitrogen dioxide (NO₂) concentrations, showing a good reproduction of both daily peaks and their diurnal variations. The model also showed a good capability to reproduce the magnitude of volatile alkane, aromatic and carbonyl compound concentrations. PM₁₀ model results revealed the tendency to under-predict the observed values. PM composition model results were compared with observed data, evidencing good results for elemental carbon (EC), nitrate (NO₃⁻) and ammonium (NH₄⁺), underestimation for sulphate (SO₄²⁻) and poor performance for organic matter (OM). The soil components of PM were found to be significantly under-predicted by the model, especially during Saharan dust episodes. Overall, the study results show large areas of high O₃ and PM₁₀ concentrations where levels of pollutants should be carefully monitored and population exposure evaluated.     

Source analysis of high particulate matter days in Hong Kong

This study identifies major contributing sources of high particulate matter (PM) days in Hong Kong and conducive meteorological conditions leading to high PM. The PM₁₀ chemical composition of 3393 ambient samples collected at ten monitoring stations in Hong Kong during 1998–2005 were used as input for positive matrix factorization (PMF) modeling to identify and quantify the aerosol sources in Hong Kong. Days with PM₁₀ levels exceeding 56 μg m^?3, the average plus one standard deviation of the mass concentration of all samples, are defined as high PM days. A total of 401 samples fell in the high PM category during the study period. Biomass burning, secondary sulfate and secondary nitrate were found to be the major contributors leading to high PM, responsible for 68–73% of PM₁₀ mass on high PM days. The contributions by these sources on high PM days were 140–180% higher than their respective average concentration contributions. These sources were identified to be regional sources on the grounds of little spatial variation in their concentrations among the monitoring stations and a temporal pattern of higher in the winter and lower in the summer. Sampling days of high PM in 2004 and 2005 were individually examined for weather charts and regional surface wind maps. Weak high pressures over mainland China were the most important synoptic event leading to high PM days in the fall and winter, while typhoon episodes were responsible for most summer cases. Approximately 80% of the high PM days were in the fall and winter months (September–February). Almost all the high PM days were associated with northwesterly, northerly or northeasterly regional transport. Anthropogenic primary sources (coal combustion, vehicular exhaust, and residue oil combustion) showed the highest contributions associated with northwesterly wind, indicating the strong influence of the more urbanized areas to the northwest of Hong Kong in the Pearl River Delta region.     

Characterization of fine primary biogenic organic aerosol in an urban area in the northeastern United States

Scanning electron microscopy coupled to energy-dispersive x-ray spectroscopy (SEM/EDX) was used to quantify individual bioparticles in PM_2.5 samples collected during the Pittsburgh Air Quality Study. Microscopy-based estimates of primary biogenic organic aerosol (PBOA) mass were compared to carbohydrate mass associated with PM_2.5. Carbohydrates show substantial seasonal variations, with higher concentrations in the spring and the fall. During the summer, carbohydrates were about 30% of the estimated PBOA concentrations, but in the winter carbohydrate concentrations often greatly exceeded the PBOA mass estimate. Spores and insect detritus were the most abundant PBOA types in the summer samples, while winter samples were comprised predominantly of a mixture of microorganisms, insect and vegetative detritus. During the summer PBOA contributed on average 6.9 ± 5.4% by mass of the PM_2.5 versus 3.3 ± 1.4% of the PM_2.5 mass during the winter.     

Street-level concentrations of nitrogen dioxide and suspended particulate matter in Hong Kong

The concentrations of respirable suspended particulates (PM₁₀), fine suspended particulates (PM_2.5) and nitrogen dioxide (NO₂) were measured in various locations over the territory of Hong Kong. In order to study the contributions of these pollutants from motor vehicles and their characteristics, the attention was focused on the roadside, street-level concentrations. A statistical analysis of the sampling results was conducted to obtain general characteristics of the roadside particulate and nitrogen dioxide pollution and to investigate the effects of traffic volume and meteorological factors on the pollution levels. High correlation coefficients are found between PM₁₀, PM_2.5 and NO₂ concentration.     

Application of positive matrix factorization in characterization of PM(10) and PM(2.5) emission sources at urban roadside

The 24-h average coarse (PM₁₀) and fine (PM_2.5) fraction of airborne particulate matter (PM) samples were collected for winter, summer and monsoon seasons during November 2008-April 2009 at an busy roadside in Chennai city, India. Results showed that the 24-h average ambient PM₁₀ and PM_2.5 concentrations were significantly higher in winter and monsoon seasons than in summer season. The 24-h average PM₁₀ concentration of weekdays was significantly higher (12-30%) than weekends of winter and monsoon seasons. On weekends, the PM_2.5 concentration was found to slightly higher (4-15%) in monsoon and summer seasons. The chemical composition of PM₁₀ and PM_2.5 masses showed a high concentration in winter followed by monsoon and summer seasons.The U.S.EPA-PMF (positive matrix factorization) version 3 was applied to identify the source contribution of ambient PM₁₀ and PM_2.5 concentrations at the study area. Results indicated that marine aerosol (40.4% in PM₁₀ and 21.5% in PM_2.5) and secondary PM (22.9% in PM₁₀ and 42.1% in PM_2.5) were found to be the major source contributors at the study site followed by the motor vehicles (16% in PM₁₀ and 6% in PM_2.5), biomass burning (0.7% in PM₁₀ and 14% in PM_2.5), tire and brake wear (4.1% in PM₁₀ and 5.4% in PM_2.5), soil (3.4% in PM₁₀ and 4.3% in PM_2.5) and other sources (12.7% in PM₁₀ and 6.8% in PM_2.5).     

Characteristics of water-soluble inorganic ions in PM2.5 and PM2.5–10 in the coastal urban agglomeration along the Western Taiwan Strait Region,China

PM_2.5 and PM_2.5–10 aerosol samples were collected in four seasons during November 2010, January, April, and August 2011 at 13 urban/suburban sites and one background site in Western Taiwan Straits Region (WTSR), which is the coastal area with rapid urbanization, high population density, and deteriorating air quality. The 10 days average PM_2.5 concentrations were 92.92, 51.96, 74.48, and 89.69 μg/m³ in spring, summer, autumn, and winter, respectively, exceeding the Chinese ambient air quality standard for annual average value of PM_2.5 (grade II, 35 μg/m³). Temporal distribution of water-soluble inorganic ions (WSIIs) in PM_2.5 was coincident with PM_2.5 mass concentrations, showing highest in spring, lowest in summer, and middle in autumn and winter. WSIIs took considerable proportion (42.2～50.1 %) in PM_2.5 and PM_2.5–10. Generally, urban/suburban sites had obviously suffered severer pollution of fine particles compared with the background site. The WSIIs concentrations and characteristics were closely related to the local anthropogenic activities and natural environment, urban sites in cities with higher urbanization level, or sites with weaker diffuse condition suffered severer WSIIs pollution. Fossil fuel combustion, traffic emissions, crustal/soil dust, municipal constructions, and sea salt and biomass burnings were the major potential sources of WSIIs in PM_2.5 in WTSR according to the result of principal component analysis.     

Determination of Microgram Quantities of Inorganic Sulfate in Atmospheric Particulates

Abstract

Before a community-wide woodstove changeout program, a chemical mass balance (CMB) source apportionment study was conducted in Libby, MT, during the winter of 2003–2004 to identify the sources of fine particulate matter (PM_2.5) within the valley. Results from this study showed that residential woodstoves were the major source, contributing approximately 80% of the ambient PM_2.5 throughout the winter months. In an effort to lower the ambient PM_2.5, a large woodstove changeout program was conducted in Libby from 2005 to 2007 in which nearly 1200 old woodstoves were changed out with cleaner burning models. During the winter of 2007–2008, a follow-up CMB source apportionment study was conducted to evaluate the effectiveness of the changeout. Results from this study showed that average winter PM_2.5 mass was reduced by 20%, and woodsmoke-related PM_2.5 (as identified by the CMB model) was reduced by 28% when compared with the pre-changeout winter of 2003– 2004. These results suggest that a woodstove changeout can be an effective tool in reducing ambient levels of PM_2.5 in woodstove-impacted communities.