Evaluation of the Effects of Emission Reductions on Secondary Particulate Matter in the South Coast Air Basin of California

An Aerosol Trajectory Model (ATM) is applied to the South Coast Air Basin of California for a two-day episode in August 1982 to evaluate proposed control strategies that aim to reduce atmospheric aerosols. Model predictions Indicate that secondary organic aerosols decrease linearly with reactive hydrocarbon emissions. In addition, the model shows that If sulf ate is produced only in the gas phase by oxidation of SO₂, then reduction In SO₂ emissions yields a nearly proportional decrease In sulfate levels. Reduction in ammonia emissions, combined with reduction of NO_x emissions, gives the best results In terms of nitrate control. The order in which the emission controls are implemented Is predicted to have a major impact on the reduction of secondary atmospheric aerosols.     

Recovering CO2 From Large− and Medium-Size Stationary Combustors

This paper summarizes the results of research conducted at Ar-gonne National Laboratory (ANL) to develop and design a novel method for the recovery of CO₂ from flue gases. The basic process concept Involves the combustion of a hydrocarbon fuel using a mixture of oxygen and carbon dioxide (or CO₂ and H₂0) rather than air as the oxidant, which results In a product stream that contains primarily CO₂ and H₂O. This stream Is then dried and conditioned to meet the specifications of the end user, A slip stream of CO₂ (or CO₂, and H₂0) is used as a diluent in the combustion chamberto maintain a flame temperature equivalent to the temperature that would otherwise be obtained using air as an oxidant. The cost-effectiveness of the process in recovering C0₂ is dependent on the scale of the operation, the type of fuel used, the cost of oxygen, and the cost of capital. The sensitivity of the cost of the recovered C0₂ to these variables Is discussed, and a model for estimating the cost of CO₂ recovered using the ANL process Is presented.     

Deactivation of the Vanadia Catalyst in the Selective Catalytic Reduction Process

Results are summarized of a comprehensive study of the effects on the SCR process of all major possible poisons encountered in the combustion gases from U.S. coals. A general rule evolved from this study Is that the effect of the additive on the catalyst activity Is directly related to the basicity of the additive; poisoning Is caused by the basicity. Quantitative effects are presented, while a qualitative summary is given as follows: strong poisons-alkali metal oxides; weak poisons-oxides of alkaline earth metals, arsenic, lead phosphorus and chlorides of strong alkaline metals. SO₂ is a promoter due to its acidity. HCI, although acidic, reacts with both NH₃ (forming NH₄CI) and V₂O₅ (forming VCI₂ and VCI₃) and consequently strongly deactivates the SCR reaction.

A summary is also given for a theoretical and experimental study of the monolithic honeycomb reactor using both undoped and poison-doped catalysts. The results showed that the reactor performance can be predicted directly from the intrinsic catalyst activity through a model.     

Development and Demonstration of an Explicit Lumped-Parameter Biofilter Model and Design Equation Incorporating Monod Kinetics

Abstract

Biofiltration is an economical air pollution control (APC) technology, particularly suitable for the treatment of air-streams having high flow rates and low concentrations of volatile organic compounds (VOCs). This technology utilizes enzymatic catalysis at ambient conditions to mineralize such pollutants to CO₂, H₂O, and salts. A pilot-scale study conducted for more than 4 years investigated the development of a new biofiltration technology employing trickle bed air biofilters (TBABs). Following the completion of this experimental study, additional data analysis was performed to develop a simple lumped-parameter biofilter model, assuming first-order kinetics. This model related the observed biofilter performance to the principle independent physical, thermodynamic, and biochemical parameters. The initial model has subsequently been expanded to incorporate Monod kinetics. In this paper, the development and use of the final explicit lumped-parameter biofilter model and design equation, incorporating Monod kinetics, are presented. To facilitate the application of this model, practical procedures are also presented for the determination of VOC solubility, VOC biokinetic Monod parameters, and the maximum practical biofilter inlet VOC concentration.     

Control of Fine Particulate (PM2.5) Emissions from Restaurant Operations

ABSTRACT

This paper describes efforts to reduce particulate matter (PM) emissions from restaurant operations, including application of an existing control method to a new equipment type. Commercial charbroiling in the South Coast Air Basin results in emissions of approximately 10 tons/day of fine particulate matter ₍PM_2.5) and 1.3 tons/day of volatile organic compounds (VOCs). Over a seven-year period, the South Coast Air Quality Management District worked with industry to develop test methods for measuring emissions from various cooking operations, evaluate control technologies, and develop a rule to reduce these emissions.

Of the two basic types of charbroilers—chain-driven and underfired—underfired produce four times the emissions when equivalent amounts of product are cooked. Cost-effective control technology is currently available only for chain-driven charbroilers. The application of flameless catalytic oxidizers to chain-driven charbroilers was found to effectively reduce emissions by at least 83% and is cost-effective. The catalysts have been used worldwide at restaurants for several years. Research efforts are underway to identify control options for underfired charbroilers.

Implementation of Rule 1138, Control of Emissions from Restaurant Operations, adopted November 14, 1997, will result in reductions of 0.5 tons/day of PM_2.5 and 0.2 tons/day of VOCs. Future rules will result in reductions from underfired charbroilers and possibly other restaurant equipment when cost-effective solutions are available.     

Effect of Dust Size Distribution on the Collection Efficiency of Pulse-Jet Fabric Filters

Recent advances in vehicle emission control technology have reduced the effectiveness of the conventional tailpipe test used In inspection and maintenance programs. A different approach Is being followed in Harris County, Texas (Houston area), based on identification and correction of misfuellng and tampering. Misfueling Is being identified by using a lead-sensitive test paper to detect lead deposits in the tailpipe that result from using leaded gasoline. Field tests of this procedure demonstrated that it Is reliable and accurate for the Intended purpose. The data also indicated the need to observe certain precautions to avoid contamination and other potential sources of error. This procedure and other emission-related checks have been added to the annual safety inspections. These tests are conducted on vehicles of 1980 model year and later, by approximately 1150 Inspection stations throughout the county that conduct annual safety Inspections. Experience with the first few months of this program has been excellent.     

The Use of Electrokinetics for Hazardous Waste Site Remediation

The Superfund Innovative Technology Evaluation (SITE) program was authorized as part of the 1986 amendments to the Superfund legislation. It represents a joint effort between U.S. EPA’s Office of Research and Development and Office of Solid Waste and Emergency Response. The program is designed to assist and encourage the development of waste treatment technologies that would contribute to more solutions to our hazardous waste problems.

Recently, EPA, through the SITE program, issued a work assignment to assess the “stateof- the-art” of electroklnetically enhanced contaminant removal from soils. Prior research efforts, both laboratory and field, have demonstrated that electroosmosis has the potential to be effective In facilitating the removal of certain types of hazardous wastes from soils. Particularly encouraging results have been achieved with inorganics in fine-grained soils where more traditional removal alternatives are less effective.

Although the results of various studies suggest that electrokinetics is a promising technology, further testing Is needed at both the laboratory and field levels to fully develop this technology for site remediation. A conceptual test program Is presented based on best available data which incorporates system design and operating parameters used in previous applications of this technology In the use of electrokinetics treatment as a remediation technique at hazardous waste sites.     

Relationship between bioconcentration in fish and steric factors of hydrophobic chemicals

Most polychlorinated naphthalones (PCN) accumulate rapidly according to their hydrophobicity. The uptake and ellmination rate constants are comparable to those of chlorinated benzenes and biphenyls.For most PCN-congeners the resulting bioaccumulation factors show an increase with increasing hydrophobicity. For higher K_d,oct-values (>10⁵) however, no further increase of K_c is observed (K_c. max. = 3.5.10⁴).For the two hepta- and the octachloronaphthalenes no detectable concentrations are found in the fishes, although no restricted blo-availability could be expected. Based on these observations and on data obtained from the literature. a loss of membrane permeation is suggested for hydrophobic molecules with widths over 9.5 Å.In addition a membrane permeation model, as part of the accumulation process of hydrophobic chemicals. Is proposed, which is based on diffusion and partition processes.     

Thin Film Solar Cells: Research in an Industrial Perspective

Electricity generation by photovoltaic conversion of sunlight is a technology in strong growth. The thin film technology is taking market share from the dominant silicon wafer technology. In this article, the market for photovoltaics is reviewed, the concept of photovoltaic solar energy conversion is discussed and more details are given about the present technological limitations of thin film solar cell technology. Special emphasis is given for solar cells which employ Cu(In,Ga)Se₂ and Cu₂ZnSn(S,Se)₄ as the sunlight-absorbing layer.     

A Transition-Flow Reactor Tube for Measuring Trace Gas Concentrations

Dry deposition contributes significantly to the acidification of ecosystems. However, difficulties in measuring dry deposition of reactive gases and fine particles make routine direct monitoring impractical. An alternate approach is to use the “concentration monitoring” method in which dry deposition flux is estimated as the product of measured concentration and estimated deposition velocity. A sampling system that performs over the period of 6 hours to 7 days, depending on atmospheric concentrations, has been developed. It consists of a Teflon cyclone to exclude particles larger than about 2 μm, selective solid adsorption media for reactive gases—some of which are sampled from a transition flow to avoid possible bias from particle evaporation, a particle filter, and a final gas adsorption filter to collect the remaining trace gas. The sampler Is the first reported application of transition flow mass transfer for the collection and quantitative measurement of trace atmospheric gases. Laboratory and field tests have shown that the sampler performs well for HNO₃(g).     

Climate forcing by the on-road transportation and power generation sectors

The on-road transportation (ORT) and power generation (PG) sectors are major contributors to carbon dioxide (CO₂) emissions and a host of short-lived radiatively-active air pollutants, including tropospheric ozone and fine aerosol particles, that exert complex influences on global climate. Effective mitigation of global climate change necessitates action in these sectors for which technology change options exist or are being developed. Most assessments of possible energy change options to date have neglected non-CO₂ air pollutant impacts on radiative forcing (RF). In a multi-pollutant approach, we apply a global atmospheric composition-climate model to quantify the total RF from the global and United States (U.S.) ORT and PG sectors. We assess the RF for 2 time horizons: 20- and 100-year that are relevant for understanding near-term and longer-term impacts of climate change, respectively. ORT is a key target sector to mitigate global climate change because the net non-CO₂ RF is positive and acts to enhance considerably the CO₂ warming impacts. We perform further sensitivity studies to assess the RF impacts of a potential major technology shift that would reduce ORT emissions by 50% with the replacement energy supplied either by a clean zero-emissions source (S1) or by the PG sector, which results in an estimated 20% penalty increase in emissions from this sector (S2). We examine cases where the technology shift is applied globally and in the U.S. only. The resultant RF relative to the present day control is negative (cooling) in all cases for both S1 and S2 scenarios, global and U.S. emissions, and 20- and 100-year time horizons. The net non-CO₂ RF is always important relative to the CO₂ RF and outweighs the CO₂ RF response in the S2 scenario for both time horizons. Assessment of the full impacts of technology and policy strategies designed to mitigate global climate change must consider the climate effects of ozone and fine aerosol particles.     

Artificial intelligence modeling to evaluate field performance of photocatalytic asphalt pavement for ambient air purification

In recent years, the application of titanium dioxide (TiO₂) as a photocatalyst in asphalt pavement has received considerable attention for purifying ambient air from traffic-emitted pollutants via photocatalytic processes. In order to control the increasing deterioration of ambient air quality, urgent and proper risk assessment tools are deemed necessary. However, in practice, monitoring all process parameters for various operating conditions is difficult due to the complex and non-linear nature of air pollution-based problems. Therefore, the development of models to predict air pollutant concentrations is very useful because it can provide early warnings to the population and also reduce the number of measuring sites. This study used artificial neural network (ANN) and neuro-fuzzy (NF) models to predict NO_x concentration in the air as a function of traffic count (T_r) and climatic conditions including humidity (H), temperature (T), solar radiation (S), and wind speed (W) before and after the application of TiO₂ on the pavement surface. These models are useful for modeling because of their ability to be trained using historical data and because of their capability for modeling highly non-linear relationships. To build these models, data were collected from a field study where an aqueous nano TiO₂ solution was sprayed on a 0.2-mile of asphalt pavement in Baton Rouge, LA. Results of this study showed that the NF model provided a better fitting to NO_x measurements than the ANN model in the training, validation, and test steps. Results of a parametric study indicated that traffic level, relative humidity, and solar radiation had the most influence on photocatalytic efficiency.     

Destruction of Volatile Organic Compounds Using Catalytic Oxidation

Catalytic oxidation is an air pollution control technique in which volatile organic compounds (VOCs) and vapor-phase air toxics in an air emission stream are oxidized with the help of a catalyst Design of catalytic systems for control of point source emissions is based on stream-specific characteristics and desired control efficiency. This paper discusses the key emission stream characteristics and VOC characteristics that affect the applicability of catalytic oxidation. The application of catalytic oxidation technology to four types of air emission sources is discussed: (1) groundwater stripping operations; (2) graphic arts facilities; (3) flexographic printing plants; and (4) latex monomer production. The characteristics of each of these emissions are discussed along with the catalytic technology used to control these emissions.     

Metolachlor and chlorothalonil dissipation in gypsum-amended soil

This work focused on the interactive effects of the fungicide chlorothalonil (2,3,4,6-tetrachloro-1,3-benzendicarbonitrile) and gypsum on the persistence of the soil-residual herbicide metolachlor (2-chloro-N-(6-ethyl-o-tolyl)-N-[(1RS)-2-methoxy-1-methylethyl]acetamide). Gypsum application was included due to its widespread use on peanut (Arachis hypogaea). Both agricultural grade gypsum and reagent CaSO₄-2H₂O were tested. A laboratory soil incubation was conducted to evaluate interactive effects. Results indicated 1.5X greater metolachlor half-life (DT₅₀) in soil amended with chlorothalonil (37 d) as compared to control soil (25 d). The two gypsum sources alone increased metolachlor DT₅₀ to about 32 d and with the combination of chlorothalonil and gypsum, DT50 was 50 d, 2-fold greater than the control. Chlorothalonil dissipation was rapid (DT₅₀ < 4d). A possible explanation for metolachlor dissipation kinetics is a build-up of the chlorothalonil intermediate (4-hydroxychlorothalonil) which limited soil microbial activity and depleted glutathione S-transferase (GST) from chlorothalonil detoxification. Further information related to gypsum impacts is needed. Results confirm previous reports of chlorothalonil impeding metolachlor dissipation and showed the gypsum application extended persistence even longer. Farming practices, such as reducing metolachlor application rates, may need to be adjusted for peanut cropping systems where chlorothalonil and gypsum are used.     

Performance/Cost Estimates for Retrofitting Control Technologies

The U.S. EPA’s Air and Energy Engineering Research Laboratory is responsible for assessing control technology performance and costs under the National Acid Precipitation Assessment Program. A major part of this assessment involves developing site-specific estimates of the performance and costs of retrofitting SO₂ and NO_x control technologies for the top 200 SO₂- emitting (1980) coal-fired power plants in the 31-state eastern region. This effort includes detailed evaluation of a small number of plants (30 or less) representing a cross-section of the top 200 population. In cooperation with the states of Ohio and Kentucky (in conjunction with the U.S. EPA’s State Acid Rain Grant Program), efforts were undertaken to visit and conduct detailed evaluation of 12 coal-fired plants—five in Ohio, seven in Kentucky and the Tennessee Valley Authority System. A variety of commercial and advanced SO₂ and NO_x control technologies—including precombustion, combustion (in-furnace), and postcombustion (flue gas cleanup) technologies—were applied to each plant through conceptual designs. Retrofit factors (applied to the capital cost of a new pollution control system), cost “adders” (e.g., movement of existing equipment), and costs were developed for applying the control technologies to the boilers of each plant. Results of these and subsequent efforts will be valuable in evaluations of acid deposition control strategies by federal and state agencies and by electric utilities.     

Dry FGD at United Power Association’s Stanton Station

The United Power Association’s dry FGD system at Stanton, North Dakota was the first utility-operated lime spray dryer to be put into service in the United States. At 60 MW in size, it utilizes a single spray dryer vessel with three rotary atomizers and a ten-compartment fabric filter. It is currently operating at better than expected efficiency and Is meeting state and federal air quality requirements. Start-up and operation have shown that certain areas of design and operating conditions are critical to reliable operation. Flue gas, slurry, and water distribution and mixing must be carefully controlled if reliable, long term operation is to be achieved. Likewise, water chemistry Is Important in the reagent preparation equipment. Start-up of the system was accomplished In a step-wise fashion to bring the baghouse on line first, followed by the spray dryer. The spray dryer was operated at gradually lower outlet temperatures until design conditions were met. Measures taken since start-up to ensure reliable operation, and operation over an eighteen month period are discussed. Both particulate and SO₂ emission performance are evaluated.     

On-Road,In-Use Gaseous Emission Measurements by Remote Sensing of School Buses Equipped with Diesel Oxidation Catalysts and Diesel Particulate Filters

Abstract

A remote sensing device was used to obtain on-road and in-use gaseous emission measurements from three fleets of schools buses at two locations in Washington State. This paper reports each fleet’s carbon monoxide (CO), hydrocarbon (HC), nitric oxide (NO), and nitrogen dioxide (NO₂) mean data. The fleets represent current emission retrofit technologies, such as diesel particulate filters and diesel oxidation catalysts, and a control fleet. This study shows that CO and HC emissions decrease with the use of either retrofit technology when compared with control buses of the same initial emission standards. The CO and HC emission reductions are consistent with published U.S. Environmental Protection Agency verified values. The total oxides of nitrogen (NO_x), NO, and the NO₂/NO_x ratio all increase with each retrofit technology when compared with control buses. As was expected, the diesel particulate filters emitted significantly higher levels of NO₂ than the control fleet because of the intentional conversion of NO to NO₂ by these systems. Most prior research suggests that NO_x emissions are unaffected by the retrofits; however, these previous studies have not included measurements from retrofit devices on-road and after nearly 5 yr of use. Two 2006 model-year buses were also measured. These vehicles did not have retrofit devices but were built to more stringent new engine standards. Reductions in HCs and NO_x were observed for these 2006 vehicles in comparison to other non-retrofit earlier model-year vehicles.     

A novel use of anaerobically digested liquid swine manure to potentially control soybean cyst nematode

Experiments were carried out in two steps to determine the effect of anaerobically digested swine manure on soybean cyst nematode (SCN) egg control. In the first step, liquid swine manure underwent anaerobic digestion to search for the best digestion time for both volatile fatty acids (VFA) and ammonium nitrogen (NH₄ ⁺) enrichment. The results showed that about 17 and 28 days of incubation were needed, respectively, to reach the maximal levels of VFA and NH₄ ⁺ in the manure. In the second step, raw, VFA-enriched, and NH₄ ⁺-enriched manure were applied separately, at four different rates (25, 50, 100, and 200 mL/pot), to soil pots inoculated with nematode eggs in a greenhouse environment. Soil samples were collected 35 and 61 days after inoculation to determine the effect of such treated manure on SCN egg productivity. The data indicated that the SCN egg counts were inversely related to the manure application rates in a linear manner with correlation coefficients of 0.998, 0.967, and 0.900 for raw, NH₄ ⁺-enriched, and VFA-enriched manure for the 35-day samples. While no such relationships were found for the 61-day samples, implying that none of the treatments were still effective 61 days after application. At the four application rates, the VFA-enriched manure performed best in reducing SCN egg counts (by 18.1, 19.5, 34.3, and 18.6%) as compared to the raw manure treatment. In contrast, the NH₄ ⁺-enriched manure achieved mostly negative reductions. To achieve the best control of SCN egg growth, the VFA-enriched manure should be used and applied to soybean fields every 35 days.     

Summary of the 1991 EPRI/EPA/DOE SO2 Control Symposium

The 1991 SO₂ Control Symposium was held December 3-6, 1991, in Washington, D.C. The symposium, jointly sponsored by the Electric Power Research Institute (EPRI), the U.S. Environmental Protection Agency (EPA), and the U.S. Department of Energy (DOE), focused attention on recent improvements in conventional sulfur dioxide (SO₂) control technologies, emerging processes, and strategies for complying with the Clean Air Act Amendments of 1990. Its purpose was to provide a forum for the exchange of technical and regulatory information on SO₂ control technology. Over 800 representatives of 20 countries from government, academia, flue gas desulfurization (FGD) process suppliers, equipment manufacturers, engineering firms, and utilities attended. In all, 50 U.S. utilities and 10 utilities in other countries were represented. In 11 technical sessions, a diverse group of speakers presented 111 technical papers on development, operation, and commercialization of wet and dry FGD, Clean Coal Technologies, and combined sulfur dioxide/nitrogen oxides (SO₂/NO_x processes.     

Technology Innovations and Experience Curves for Nitrogen Oxides Control Technologies

Abstract

This paper reviews the regulatory history for nitrogen oxides (NO_x) pollutant emissions from stationary sources, primarily in coal-fired power plants. Nitrogen dioxide (NO₂) is one of the six criteria pollutants regulated by the 1970 Clean Air Act where National Ambient Air Quality Standards were established to protect public health and welfare. We use patent data to show that in the cases of Japan, Germany, and the United States, innovations in NO_x control technologies did not occur until stringent government regulations were in place, thus “forcing” innovation. We also demonstrate that reductions in the capital and operation and maintenance (O&M) costs of new generations of high-efficiency NO_x control technologies, selective catalytic reduction (SCR), are consistently associated with the increasing adoption of the control technology: the so-called learning-by-doing phenomena. The results show that as cumulative world coal-fired SCR capacity doubles, capital costs decline to ~86% and O&M costs to 58% of their original values. The observed changes in SCR technology reflect the impact of technological advance as well as other factors, such as market competition and economies of scale.