The performance of solar powered desiccant dehumidifier in India: an experimental investigation

The regeneration and adsorption of desiccant wheel for producing the dry air was experimentally investigated. The air needed for regeneration was heated in an evacuated tube solar collector with surface area 4.44 m². The desiccant wheel is regenerated at the temperature in the range of 43.9–72.6°C. The regeneration and adsorption performances are affected by the regeneration temperature, wheel rotation, air flow rate (process and regeneration) and ambient conditions. By comparing the adsorption and regeneration performance at different air flow rate and constant rph, it was found that maximum adsorption and regeneration rates are obtained at air flow rate of 210.789 kg/h. Regeneration temperature directly affects the effectiveness of the desiccant wheel. Maximum desiccant wheel effectiveness of regeneration sector and adsorption sector is obtained at air flow rate of 105.394 kg/h. The regeneration performance of desiccant wheel with evacuated tube solar air collector is suitable for the Indian climate.     

Performance of a hybrid solar collector system in days with stable and less stable radiative regime

The aim of this work is to analyse the performance of a solar energy collector system for water and air heating in real working conditions. Two coupled mathematical models have been developed. One of them describes the thermal behaviour of the Hybrid Solar Collector (HSC) and the second one describes the simultaneous operation of the HSC and of a fully mixed water storage tank. The dependence of the performance of the HSC system on the following three parameters has been studied: (1) water and air mass flow rate; (2) water pipe diameter and air channel height; (3) water storage tank volume. The mathematical models were used to evaluate the HSC system performance during 29 different days, covering all four seasons. A higher water flow rate generally enhances the thermal efficiency of the HSC system, but the enhancement became significantly smaller at higher air flow rates. Positive but small values are recommended for the difference between the fluid temperature at solar collectors exit and the water temperature in the tank. The thermal efficiency of the HSC system is higher on nearly clear sky and decreases in case the amount of clouds on the sky increases.     

Solar-driven technology for freshwater production from atmospheric air by using the composite desiccant material “CaCl<Subscript>2</Subscript>/floral foam”

In this communication, experiments have been performed to check the capability of the newly formed composite desiccant material (CaCl₂/floral) for the extraction of freshwater from atmospheric air. Three numbers of solar glass desiccant box type system (SGDBS) with a captured area of 0.36 m² each, have been used. The design parameters for the water production are height of glass from desiccant bed at 0.22 m, inclination in angle as 30°, the effective thickness of glass as 3 mm and number of glazing as single. The maximum yield by the new composite desiccant material is 0.35 ml/cm³/day. The efficiency of the system SGDBS with 37 % concentration of CaCl₂ is 76.44 %.     

Performance analysis of solar water heating system in Centre for DNA Fingerprinting and Diagnostics (CDFD), Southern region of India

In the present study, a natural circulation thermosyphon flat plate solar water heater has been tested at the CDFD, Hyderabad (17.37°N, 78.43°E) Andhra Pradesh, India. Experimental data were noted on a sunny day. Dynamic response of the system to variations in solar insulation was studied and analyzed. T _inlet °C and T _outlet °C temperatures were recorded. The performance of the system can be improved by using aluminum tape inserts into the collector fins. The objective of the present study is to evaluate the performance of flat plate collector with and without inserts (aluminum strip of 1 mm thick, 3 mm width and 203 mm length). It is expected that with the same collector with the same flow rate, higher efficiency can be obtained by inserting the tapes inside the collector copper fins (9 mm). Thus, the cost of the system can be further bringing down by enhancing the collector efficiency.     

Energy and exergy analysis of a PCM-based solar powered winter air conditioning using desiccant wheel during nocturnal

In this paper, heating and humidification of air for space have been carried out by using a phase change material (PCM)-based solar-powered desiccant wheel air conditioning (SPDWAC) in winter. The analysis of the setup has been done at different air flow rates. At low and high air flow rates, system has mean thermal coefficient of performance of 0.121 and 0.172, respectively, and mean exergy efficiency of 0.0787 and 0.0846, respectively. The mean thermal coefficient of performance of the system at high air flow rate (127.23 kg h-1) is 1.42 times the low air flow rate (63.62 kg h-1) and average exergy efficiency of the system at high air flow rate is 1.07 times the low air flow rate. It is observed that with an increase in air flow rate, efficiency of the evacuated tube solar air collector (ETSAC) increases. The average efficiency of the ETSAC at high air flow rate is 15.60%. The maximum average energy efficiency (17.80%) and exergy efficiency (17.08%) of the PCM storage system have been obtained at high air flow rate. The overall performance of the system showed that the use of PCM storage is feasible to run the system in winter during the hours of darkness.     

Comparative experimental analysis of the effect of convective heat losses on the performance of parabolic dish water heater

This paper reveals comparative experimental analysis of the effect of variation of natural and forced convection heat losses on the performance of prototype parabolic dish water heater with coated and non-coated receivers. With the above-described system, hot water needs in domestic applications can be fulfilled instantly. A parabolic dish collector was used for instant water heating. Design of solar parabolic dish collector consists of truncated cone-shaped helical coiled receiver made up of copper at focal point. Instantaneous efficiency of 63% and 48% has been achieved with coated and non-coated receivers. This prototype has been evaluated for its performance with water flow rate of 0.0076 kg/s during the months of April and May 2010 at Shivaji University, Kolhapur, Maharashtra, India (latitude: 16.42° North, longitude: 74.13° West).     

Viability of solar photovoltaics as an electricity generation source for Jordan

Viability of solar photovoltaics as an electricity generation source for Jordan was assessed utilising a proposed 5 MW grid‐connected solar photovoltaic power plant. Long‐term (1994–2003) monthly average daily global solar radiation and sunshine duration data for 24 locations – distributed all over the country – were studied and analysed to assess the distribution of radiation and sunshine duration over Jordan, and formed an input to the RetScreen Software for evaluation and analysis of the proposed plant's electricity production and economic feasibility. It was found that depending on the geographical location, the global solar radiation on horizontal surface varied between 1.51 and 2.46 MWh/m²/year with an overall mean value of 2.01 MWh/m²/year for Jordan. The sunshine duration was found to vary, according to the location, between 8.47 and 9.68 hours/day, with a mean value of 9.07 hours/day and about 3311 sunshine hours annually for Jordan. The annual electricity production of the proposed plant varied depending on the location between 6.886 and 11.919 GWh/year, with a mean value of 9.46 GWh/year. The specific yield varied between 340.9 and 196.9 kWh/m², while the mean value was 270.59 kWh/m². Analysis of the annual electricity production of the plant, the specific yield, besides the economic indicators, i.e. internal rate of return, simple payback period, years to positive cash flow, net present value, annual life cycle saving, benefit/cost ratio, and cost of energy – for all sites – showed that Tafila and Karak are the most suitable sites for the solar photovoltaic power plant's development and Wadi Yabis is the worst. The results also showed that an average of 7414.9 tons of greenhouse gases can be avoided annually utilising the proposed plant for electricity generation at any part of Jordan.     

Experimental investigation of solar-powered desiccant cooling system by using composite desiccant “CaCl<Subscript>2</Subscript>/jute”

A solar-powered composite desiccant cooling system has been experimentally investigated. It consists of evacuated tube solar water heater, composite desiccant bed heat exchanger (CDBHE), direct evaporative cooling unit and cooling tower. The composite desiccant material has been synthesized by using iron mesh and jute layer impregnated with calcium chloride solution, and this composite desiccant is placed in shell- and tube-type heat exchanger to make CDBHE. In this desiccant cooling system, the evacuated tube solar water heater is used to produce required hot water for regeneration of composite desiccant material. A cooling tower is used to produce cooling water which is pumped into CDBHE during dehumidification process to remove heat of adsorption. Direct evaporative cooling unit is used to cool the outlet process air of CDBHE. It has been found that the average dehumidification rate increases by 54.1 % when using circulating cooling water. The COP_th of desiccant cooling system has been found to be 0.46 with a cooling capacity of 353.8 W.     

Effects of collector types in sampling of atmospheric depositional fluxes

The bulk gross alpha, gross beta and ⁷Be depositional fluxes were measured in Málaga (36.7°N, 4.5°W), a coastal Mediterranean station in the south of Spain for one whole year. In order to quantify the local variation of deposition rates, we have analysed the monthly results from two deposition collectors: a “pot “collector with a continuous water-covered surface and a “funnel” collector. In general, the alpha and beta depositional fluxes from the funnel collector were approximately two times lower than the pot collector. Whereas for the cosmogenic ⁷Be, the depositional flux of ⁷Be from funnel collector was also approximately two times lower than the pot collector. A good correlation of the depositional flux of ⁷Be has been obtained from both collectors.     

Comparative study of solar-powered water production from atmospheric air using different desiccant materials

In this paper, experiments have been performed in order to determine the quantity of water produced from the atmospheric air using different desiccant materials named Silica gel, Activated alumina and Molecular sieve 13 X. On the bases of experimental results, a correlation is derived among the different temperatures and water production using Central Composite Design (CCD) of Response Surface Methodology. A newly designed solar glass desiccant box type system (SGDBS), three in number, has been used. Design parameters for the production of water has been taken as depth of material from the glass is 0.22 m, inclination in angle as 30°, effective thickness of glass as 3 mm and number of glazing as single. It has been found experimentally that the maximum quantity of water produced by Silica gel, Activated alumina and Molecular sieve 13 X is 160, 20 and 35 ml/kg/day, respectively. Whereas theoretically, value of water produced by the Silica gel, Activated alumina and Molecular sieve 13 X is 600, 28 and 60 ml/kg/day, respectively.     

High resolution exposure modelling of heat and air pollution and the impact on mortality

BackgroundElevated temperature and air pollution have been associated with increased mortality. Exposure to heat and air pollution, as well as the density of vulnerable groups varies within cities. The objective was to investigate the extent of neighbourhood differences in mortality risk due to heat and air pollution in a city with a temperate maritime climate.MethodsA case-crossover design was used to study associations between heat, air pollution and mortality. Different thermal indicators and air pollutants (PM₁₀, NO₂, O₃) were reconstructed at high spatial resolution to improve exposure classification. Daily exposures were linked to individual mortality cases over a 15 year period.ResultsSignificant interaction between maximum air temperature (Ta_max) and PM₁₀ was observed. During “summer smog” days (Ta_max > 25 °C and PM₁₀ > 50 μg/m³), the mortality risk at lag 2 was 7% higher compared to the reference (Ta_max 15 °C and PM₁₀ 15 μg/m³). Persons above age 85 living alone were at highest risk.ConclusionWe found significant synergistic effects of high temperatures and air pollution on mortality. Single living elderly were the most vulnerable group. Due to spatial differences in temperature and air pollution, mortality risks varied substantially between neighbourhoods, with a difference up to 7%.     

Integrated hydrologic–economic decision support system for groundwater use confronting climate change uncertainties in the Tunuyán River basin,Argentina

This study presents an integrated hydrologic–economic model as decision support system for groundwater use and incorporates uncertainties of climate change. The model was developed with the Vensim software (Ventana Systems) for system dynamic simulations. The software permitted the integration of economic variables along with hydrologic variables, in a unified format with the aim of evaluating the economic impacts of climate change on arid environments. To test the model, we applied it in one of the upper Tunuyán River sub-basin, located in the Mendoza Province (Argentina), where irrigation comes from groundwater. The model defines the best mix of crops and the total land use required to maximize the total river sub-basin monetary income, considering as a limit the amount of water that does not exceed the natural annual aquifer recharge. To estimate the impacts of climatic changes, four scenarios were compared: the business as usual (with the number of existing wells) in a dry year with a temperature increase of 4 °C; the business as usual in a wet year with an increase in temperature of 1.1 °C; an efficient use of wells in a dry year and a temperature increase of 4 °C and an efficient use of wells in a wet year with a temperature increase of 1.1 °C. Outputs calculated by the model were: land use per crop, total sub-basin net benefit, total sub-basin water extraction, water extraction limit depending on river discharge and total number of wells required to irrigate the entire area. Preliminary results showed that the number of existing wells exceeded the optimized number of wells required to sustainably irrigate the entire river sub-basin. Results indicated that in an average river discharge year, if wells were efficiently used, further rural development would be possible, until the limit of 350 million m³ of water extraction per year was reached (650 million m³ for a wet year and 180 million m³ for a dry year). The unified format and the low cost of the software license make the model a useful tool for Water Resources Management Institutions, particularly in developing countries.     

Contrasting impacts of climate change across seasons: effects on flatfish cohorts

The Senegal sole, Solea senegalensis, is a species of flatfish that has several distinct cohorts of 0-group juveniles which use estuarine nurseries in summer and winter. The early cohort is more abundant and grows faster than the late cohort that stays in the nurseries during winter; however, climate warming may have an impact on the dynamics of this species’ juveniles. This study aimed to compare mortality, metabolic response and growth of S. senegalensis juveniles at different temperatures, reflecting present-day temperature (winter—12 °C; summer—24 °C) and future temperature (plus 3 °C) conditions, in estuarine nurseries in the southern European population. Mortality was low at 12 °C, being only 10 %, increasing to 30 % at 15 °C, 40 % at 24 °C and at 27 °C it hit 70 %. Metabolic rate increased steadily with increasing temperatures, yet it increased steeply from 24 to 27 °C. Thermal sensitivity was high for the temperature interval between 24 and 27 °C. Growth was very slow at 12 °C, at a rate of 0.03 mm day^?1, increasing to 0.22 mm day^?1 at 15 °C, and to 0.60 mm day^?1, at 24 °C. However, at 27 °C growth rapidly declined to 0.12 mm day^?1. Warming will be beneficial for the late cohort, resulting in a major increase in growth. However, the early cohort will not benefit from warming, due to high mortality and arrested growth, which clearly indicates that this species is under severe thermal stress at 27 °C. Thus, here we show, for the first time, that climate change may induce contrasting seasonal impacts on fish bio-ecology and physiology, namely in species with several cohorts over the course of the year. Phenotypic and/or genotypic plasticity may limit the impacts of climate change.     

Indoor air pollution due to organic gases and vapours of solvents in building materials

The emission of organic gases and vapours of solvent type from 42 commonly used building materials was measured under standard atmospheric conditions. An average of 22 compounds was found in the air around each building material, and the total concentration of gases and vapours was from 0.01 to 1410 mg/m³. The average arithmetic emission rate was 9.5 mg/m² h, and 52 different compounds were identified. A mathematical model was established for the indoor air concentrations of pollutants originating from building materials. The model was tested on three model rooms constructed from the materials investigated. The calculated total air concentrations of gases and vapours in the three rooms ranged from 1.6 to 23.6 mg/m³, and the number of compounds in the air from 23 to 32. These concentrations and number of compounds did not differ from those found in actual rooms similar in size and construction to the model rooms. The risks of health effects due to the compounds identified from the building materials were investigated, and criteria for future air quality standards are discussed. It is concluded that the possibility of negative health effects cannot be neglected, especially not for the more sensitive minority of the general population.     

Future climate and adverse health effects caused by fine particulate matter air pollution: case study for Poland

Ground level air pollution, especially fine particulate matter (PM_2.5), has been associated with a number of adverse health effects. The dispersion of PM_2.5 through the atmosphere depends on several mutually connected anthropogenic, geophysical and meteorological parameters, all of which are affected by climate change. This study examines how projected climate change would affect population exposure to PM_2.5 air pollution in Poland. Population exposure to PM_2.5 in Poland was estimated for three decades: the 1990s, 2040s and 2090s. Future climate conditions were projected by Regional Climate Model RegCM (Beta), forced by the general atmospheric circulation model ECHAM5. The dispersion of PM_2.5 was simulated with chemical transport model CAMx version 4.40. Population exposure estimates of PM_2.5 were 18.3, 17.2 and 17.1 μg/m³ for the 1990s, 2040s and 2090s, respectively. PM_2.5 air pollution was estimated to cause approximately 39,800 premature deaths in the population of Poland in the year 2000. Our results indicate that in Poland, climate change may reduce the levels of exposure to anthropogenic particulate air pollution in future decades and that this reduction will reduce adverse health effects caused by the air pollution.     

Indoor air quality and minimum ventilation rate

In a 30-m³ test chamber the air pollutants caused by man were measured. Variables were the number of persons and the rate of air change. During 2-h test sessions the temperature, relative humidity, carbon dioxide, and intensity of odors were measured. The relationship between the perceived odor intensities and the concentrations of carbon dioxide-independent of the number of persons and the air change rate—was observed. At air change rates of 12–15 m³/person/h, the carbon dioxide concentration was not higher than 0.15% and the odor intensity was evaluated only as a “slight annoyance.” Higher ventilation rates are necessary if smoking and increased physical activities are done in the rooms.     

Can car air filters be useful as a sampling medium for air pollution monitoring purposes?

Urban air quality and real human exposure to chemical environmental stressors is an issue of high scientific and political interest. In an effort to find innovative and inexpensive means for air quality monitoring, the ability of car engine air filters (CAFs) to act as efficient samplers collecting street level air, to which people are exposed to, was tested. In particular, in the case of taxis, air filters are replaced after regular distances, the itineraries are almost exclusively urban, cruising mode is similar and, thus, knowledge of the air flow can provide with an integrated city air sample. The present pilot study focused on polycyclic aromatic hydrocarbons (PAHs), the most important category of organic pollutants associated with traffic emissions. Concentrations of ΣPAHs in CAFs ranged between 650 and 2900 μg CAF^− 1, with benzo[b]fluoranthene, benzo[k]fluoranthene and indeno[123-cd]pyrene being the most abundant PAHs. Benzo[a]pyrene (BaP) ranged between 110 and 250 μg CAF^− 1, accounting regularly for 5–15% of the total carcinogenic PAHs. The CAF PAH loads were used to derive road-level atmospheric PAH concentrations from a standard formula relating to the CAF air flow. Important parameters/assumptions for these estimates are the cruising speed and the exposure duration of each CAF. Based on information obtained from the garage experts, an average ‘sampled air volume’ of 48,750 m³ per CAF was estimated, with uncertainty in this calculation estimated to be about a factor of 4 between the two extreme scenarios. Based on this air volume, ΣPAHs ranged between 13 and 56 ng m^− 3 and BaP between 2.1 and 5.0 ng m^− 3, suggesting that in-traffic BaP concentrations can be many times higher than the limit values set by the UK (0.25 ng m^− 3) and the European Union (1.0 ng m^− 3), or from active sampling stations normally cited on building roof tops or far from city centres.Notwithstanding the limitations of this approach, the very low cost, the continuous availability of very high amounts of “sample”, and the “retroactivity” render it very useful and complementary to existing passive sampling techniques. This approach yields estimated air concentrations that reflect the pollutant concentrations to which taxi drivers, pedestrians, cyclists and road-related professionals are exposed.     

A passive sampling device for determining formaldehyde in indoor air

A passive sampling device based on the principle of diffusion has been developed for the determination of formaldehyde in ambient air. The sampler consists of a capped glass tube (with approximate dimensions of 2.4 × 9 cm) containing a glass-fiber filter treated with NaHSO₃. In the field, the device collects a sample by being uncapped for a specified sampling time. After being recapped and returned to the laboratory, the filter is analyzed by the chromotropic acid (CTA) method. Laboratory validation studies were conducted by exposing the sampling devices for 1 week to dry formaldehyde gas generated by passing trioxane vapor over an acid catalyst bed. In these tests, formaldehyde concentrations ranged from 0.05 to 0.80 mL/m³. Reproducibility was excellent, with relative standard deviations averaging 5.4% for five constant concentrations. The lower detection limit was determined to be 3.6 mL/m³ h. In an occupational environment an 8-h sample would be sufficient to detect compliance with the OSHA permissible exposure limit of 3 mL/m³; in a residential environment a 1-week sample would allow detection of 0.025 mL/m³ for indoor air quality audits.     

Renewable energy potential in India and future agenda of research

ABSTRACT

Demand of electrical energy is exponentially increasing causing environmental problems due to extensive use of fossil fuels. Hence, research has been promoted in renewable energy technologies to mitigate environmental pollution. Indian subcontinent is rich in renewable energy sources (RES). This paper describes potential of RES and region-wise installed capacity in India. Estimated potential of RES is 57 GW which is targeted to be 175 GW by 2022. A logical framework for our future research work has been presented. This includes performance optimisation of solar pumping system and reliability assessments of the designed system using reliability indices.

Abbreviation: RES: Renewable energy resources; SHP: small hydro plants; GOI: Government of India; MNRE: Ministry of New and Renewable Energy; LHP: large hydropower; BCM: billion cubic metres; PEC: per-capita energy consumption; JNNSM: Jawaharlal Nehru National Solar Mission; DNI: direct normal irradiance; SPV: solar photovoltaic; UMPP: ultra mega green solar power project; GIS: geographic information systems; WMS: wind monitoring stations; MPWL: Madhya Pradesh windfarms Ltd.; MIB: mat river basin; SWAT: Soil and Water Assessment Tool; ROR: run of river; SMS: short message service; CDM: clean development mechanism; NIOT: national institute of ocean technology; LOLP: loss of load probability; CSO: Central Statistics Office; CEA: Central Electricity Authority; TERI: The Energy and Resources Institute; WPI: Wind Power India; IEA: International Energy Agency; EAI: Energy Alternatives India; BKP: Biomass Knowledge Portal; IRENA: International Renewable Energy Agency; GAIN: Global Agricultural Information Network; NITI: National Institution for Transforming India; NIWE: National Institute of Wind Energy; UP: Uttar Pradesh; J&K: Jammu and Kashmir; HP: Himachal Pradesh; NR: northern region; MP: Madhya Pradesh; WR: western region; TN: Tamil Nadu; AP: Andhra Pradesh; SR: southern region; ER: eastern region; NER: north eastern region; A&N: Andaman & Nicobar     

Larch forests of Middle Siberia: long-term trends in fire return intervals

Fire history within the northern larch forests of Central Siberia was studied (65 + °N). Fires within this area are predominantly caused by lightning strikes rather than human activity. Mean fire return intervals (FRIs) were found to be 112 ± 49 years (based on firescars) and 106 ± 36 years (based on firescars and tree natality dates). FRIs were increased with latitude increase and observed to be about 80 years at 64°N, about 200 years near the Arctic Circle and about 300 years nearby the northern range limit of larch stands (~71° + N). Northward FRIs increase correlated with incoming solar radiation (r = ?0.95). Post-Little Ice Age (LIA) warming (after 1850) caused approximately a doubling of fire events (in comparison with a similar period during LIA). The data obtained support a hypothesis of climate-induced fire frequency increase.