Formation, release and control of dioxins in cement kilns

Co-processing of hazardous wastes in cement kilns have for decades been thought to cause increased emissions of PCDD/PCDFs--a perception that has been evaluated in this study. Hundreds of PCDD/PCDF measurements conducted by the cement industry and others in the last few years, on emissions and solid materials, as well as recent test burns with hazardous wastes in developing countries do not support this perception. Newer data has been compared with older literature data and shows in particular that many emission factors have to be reconsidered. Early emission factors for cement kilns co-processing hazardous waste, which are still used in inventories, are shown to be too high compared with actual measurements. Less than 10 years ago it was believed that the cement industry was the main contributor of PCDD/PCDFs to air; data collected in this study indicates however that the industry contributes with less than 1% of total emissions to air. The Stockholm Convention on POPs presently ratified by 144 parties, classifies cement kilns co-processing hazardous waste as a source category having the potential for comparatively high formation and release of PCDD/PCDFs. This classification is based on early investigations from the 1980s and 1990s where kilns co-processing hazardous waste had higher emissions compared to those that did not burn hazardous waste. However, the testing of these kilns was often done under worst case scenario conditions known to favour PCDD/PCDF formation. More than 2000 PCDD/PCDF cement kiln measurements have been evaluated in this study, representing most production technologies and waste feeding scenarios. They generally indicate that most modern cement kilns co-processing waste today can meet an emission level of 0.1ngI-TEQ/m(3), when well managed and operated. In these cases, proper and responsible use of waste including organic hazardous waste to replace parts of the fossil fuel does not seem to increase formation of PCDD/PCDFs. Modern preheater/precalciner kilns generally seems to have lower emissions than older wet-process cement kilns. It seems that the main factors stimulating formation of PCDD/PCDFs is the availability of organics in the raw material and the temperature of the air pollution control device. Feeding of materials containing elevated concentrations of organics as part of raw-material-mix should therefore be avoided and the exhaust gases should be cooled down quickly in long wet and long dry cement kilns without preheating. PCDD/PCDFs could be detected in all types of solid samples analysed: raw meal, pellets and slurry; alternative raw materials as sand, chalk and different ashes; cement kiln dust, clinker and cement. The concentrations are however generally low, similar to soil and sediment.     

Emissions of PCDD/F from uncontrolled, domestic waste burning

Emissions of polychlorinated dibenzodioxin and dibenzofuran (PCDD/F) result from inefficiencies of combustion processes, most typically waste combustion. Uncontrolled combustion, such as occurs during so-called "backyard burning" of domestic waste, may therefore produce optimal conditions for formation and emission of PCDD/F. However, few assessments of PCDD/F emissions are available from these sources. This work describes the first known comprehensive assessment of PCDD/F emissions from uncontrolled, domestic waste burning. Emissions were copious, but highly variable, ranging over several orders of magnitude. The potential for emissions appears to be related primarily to combustion parameters and concentrations of various gas-phase species, the latter which may be affected by changes in waste composition, waste orientation, and/or combustion conditions.     

Dioxin emissions from waste incinerators

Mechanisms that have been proposed to account for the emission of PCDD/PCDF from municipal waste incinerators were evaluated in the light of extensive experimental data obtained from the Quebec City municipal solid waste incinerator by Environment Canada. It was found that PCDD/PCDF emissions were closely related to the quantity of material entrained by the combustion gases.     

Post-combustion syntheses of PCDD/F and PBDD/F from halogen-rich fuel is suppressed by a pebble heater technology

GOAL, SCOPE AND BACKGROUND: Changes in German and European legislation shifted processing of polymer-rich shredding residues (SR) from landfill to thermal treatment. However, when waste of electric and electronic equipment (WEEE) is the source of SR, thermal treatment is complicated by halogens as well as the presence of polybrominated dioxins and furans (PBDD/F) and brominated flame retardants (BFR). Hence, WEEE requires high temperature incineration with sufficient residence times. Post-combustion synthesis of polyhalogenated dioxins and furans (PXDD/F) is dominant in the temperature range between 250-450 degrees C. Thus, a very rapid gas cooling from 450 degrees to 250 degrees C is important for proper raw gas treatment. The pebble heater technology developed by ATZ Entwicklungszentrum (Sulzbach-Rosenberg, Germany) might serve as an alternative to the state-of-the-art quench cooling. It is based on the application of a pebble bed of natural bulk material, which the exhaust gases flows through radially. It provides an excellent heat transfer and a temperature gradient in the range of 1,500-2,000 K/m. The paper presents data of a pilot application of the pebble heater technology for the treatment of raw gas derived from the incineration of polymeric materials from WEEE. METHODS: A liquid fuel was chosen in order to minimise technical modifications of the plant. It was analysed for halogens by x-ray fluorescence, for brominated flame retardants by HPLC-UV/MS and for PXDD/F by GC-HRMS. Combustion gases were rapidly cooled down to temperatures below 200 degrees C and emissions of PBDD/F and PCDD/ F were estimated without further off-gas treatment. PBDD/F emissions were computed as PCDD/F toxicity equivalents applying two different calculation approaches. RESULTS AND DISCUSSION: PCDD/F emissions accounted for 0.04 ng I-TEQ/Nm3 and are in compliance with European emission limits. Calculated PBDD/F toxicity equivalents exceeded the emission limit of 0.1 ng I-TEQ/Nm3 by factors of 75 and 208 depending on the calculation approach. A mass balance of PBDD/F and PCDD/F congeners revealed an efficient elimination of more than 95% in most cases. Lower reduction rates (76% for 2,3,7,8-TeBDF and 82% for 1,2,3,7,8-PeBDF) were attributed to incomplete combustion. An intended recovery of halogens by one-stage scrubbing downstream of the pebble heater was ineffective, recovering 28% of the applied chlorine and 9% of the bromine, only. CONCLUSIONS: Our pilot incineration test indicates that the pebble heater technology can effectively suppress a post-combustion synthesis of PCDD/F and PBDD/F, resulting in low PCDD/F emission levels without further off-gas treatment. The presented data state that WEEE is sensible to incomplete combustion, which will lead to increased PBDD/F emissions without increasing PCDD/F emission limits. This finding is especially relevant for small and low-technical incineration appliances, which have been reported to treat WEEE in developing countries and are considered to serve as a significant source of PXDD/F these days. RECOMMENDATIONS AND PERSPECTIVES: Monitoring of PCDD/F emissions only might considerably underestimate the total emission of dioxins and dioxin-like compounds. It is therefore an ineffective means for assessing resulting health risks, at least for those waste treatment plants which are considered to handle the increasing amounts of PBDD/ F-containing polymers from WEEE in future. Consequently, it is recommended to initiate a screening programme for PXDD/F emissions in large scale incineration facilities which are capable of treating WEEE shredder residues.     

Formation and destruction of PCDD/F inside a grate furnace

Formation and destruction of polychlorinated dibenzo-p-dioxins and dibenzofurans PCDD/F during the combustion process was investigated experimentally in a pilot plant. All important process steps like the burnout of the fuel bed on the grate, the burnout of the flue gas inside the combustion chamber, the heat recovery in a boiler as well as influences of the fuel composition are described in detail.

High concentrations especially of PCDF are formed during the burnout of the fuel bed. The formation reaction is mainly influenced by the fuel composition and the burnout characteristic of the fuel bed. Fuels with low chlorine and low metal content (Cu) result only in negligible concentrations of PCDD/F.

Under stable combustion conditions characterized by an excellent flue gas burnout PCDD/F will almost be completely destroyed already inside the combustion chamber. “Cold strands” of unburned flue gas (high CO concentrations) caused by disturbed combustion conditions will result in high concentrations of PCDD and especially of PCDF in the raw gas.

A second place of PCDD/F formation is the well-known boiler section. Here fly ash deposits containing residual carbon (mainly soot particles) are the source for the formation reaction. Under stationary effective combustion conditions, they are dominant for PCDD/F concentrations in the raw gas over a very long period of time.

Stationary efficient flue gas burnout (especially soot) together with effective boiler cleaning will guaranty low concentrations of PCDD/F in the flue gas in front of the flue gas cleaning system.     

Atmospheric mercury emissions from waste combustions measured by continuous monitoring devices

Atmospheric mercury emissions have attracted great attention owing to adverse impact of mercury on human health and the ecosystem. Although waste combustion is one of major anthropogenic sources, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated atmospheric emissions of speciated mercury from the combustions of municipal solid wastes (MSW), sewage treatment sludge (STS), STS with waste plastics, industrial waste mixtures (IWM), waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form at the inlet side of air pollution control devices in all combustion cases. Its concentration was 2.0–70.6 times larger than elemental mercury concentration. In particular, MSW, STS, and IWM combustions emitted higher concentration of reactive gaseous mercury. Concentrations of both gaseous mercury species varied greatly for all waste combustions excluding woody waste. Variation coefficients of measured data were nearly equal to or more than 1.0. Emission factors of gaseous elemental mercury, reactive gaseous mercury, and total mercury were calculated using continuous monitoring data. Total mercury emission factors are 0.30 g-Hg/Mg for MSW combustion, 0.21 g-Hg/Mg for STS combustion, 0.077 g-Hg/Mg for STS with waste plastics, 0.724 g-Hg/Mg for industrial waste mixtures, 0.028 g-Hg/Mg for waste plastic combustion, and 0.0026 g-Hg/Mg for woody waste combustion. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.

Implications Although waste combustion is one of major anthropogenic sources of atmospheric mercury emission, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated speciated mercury emissions from the combustions of municipal solid wastes, sewage treatment sludge with/without waste plastics, industrial waste mixtures, waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form in all combustion cases and its concentration in the gas had large fluctuation. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.     

Chlorinated dibenzodioxin and dibenzofuran emissions from waste combustion plants in the UK

The UK Department of Trade and Industry funded extensive studies into the emissions from a variety of small scale waste combustion plants. In this paper we analyse the data on polychlorinated dibenzodioxin and polychlorinated dibenzofuran (PCDD/F) emissions from these studies. We conclude that simple correlations of PCDD/F emissions against parameters such as carbon monoxide, hydrogen chloride, feedstock composition, combustion or boiler exit temperature do not provide any guide to the emission of PCDD/F. The complex interaction between the varying fuel properties and the design features of combustion equipment mean that a greater understanding of the fundamental mechanisms is required to ensure effective control of PCDD/F at a reasonable cost.     

Open burning of household waste: Effect of experimental condition on combustion quality and emission of PCDD, PCDF and PCB

Open burning for waste disposal is, in many countries, the dominant source of polychlorinated dibenzodioxins, dibenzofurans and biphenyls (PCDD/PCDF/PCB) release to the environment. To generate emission factors for open burning, experimental pile burns of about 100 kg of household waste were conducted with emissions sampling. From these experiments and others conducted by the same authors it is found that less compaction of waste or active mixing during the fire - “stirring” - promotes better combustion (as evidenced by lower CO/CO₂ ratio) and reduces emissions of PCDD/PCDF/PCB; an intuitive but previously undemonstrated result. These experiments also support previous results suggesting PCDD/PCDF/PCB generation in open burning - while still highly variable - tends to be greater in the later (smoldering) phases of burning when the CO/CO₂ ratio increases.     

Characteristics of dioxins and metals emission from radwaste plasma arc melter system

This study investigated the emission characteristics of PCDD/Fs and the partitioning of three heavy metals (Cd, Hg and Pb) and two radioactive metal surrogates (Co and Cs) in a radwaste plasma arc melter system. Typical mixtures of low-level radioactive wastes were simulated as the trial burn surrogate wastes. The emission of PCDD/Fs and the partitioning of the metals were strongly influenced by the feed waste stream and melter operating temperature, respectively. The emissions of PCDD/Fs, cadmium and lead were greatly enhanced when the polyvinyl chloride was included in the feed waste stream. Most of the nonvolatile cobalt partitioned into the glass. A significant quantity of cesium, cadmium and lead was vaporized during the highest melter temperature test. A lower melter temperature resulted in more cesium, cadmium and lead species remaining in the glass. The results of this study suggest that wet scrubbing as well as a low-temperature two-step fine filtration, or both of them together could not effectively capture the gas-phase or fine particle phase PCDD/Fs and mercury species. In order to effectively treat low-level radioactive waste streams, the tested high-temperature melter should include an adsorption system, which could collect the gas-phase PCDD/Fs and mercury species.     

循环流化床锅炉燃烧城市生活垃圾的研究进展

城市生活垃圾(MSW)产量的与日俱增及环保要求的不断提高,使循环流化床(CFB)燃烧技术逐渐在MSW的回收和利用方面扮演越来越重要的角色.简要分析了国内外采用分类回收及综合利用、卫生填埋、堆肥和一般焚烧方法处理MSW的不足之处以及采用CFB燃烧技术的优越性,重点介绍了国内外采用CFB燃烧装置焚烧MSW的研究和应用现状,指出了目前存在的问题及努力的方向.采用CFB燃烧装置焚烧MSW关于SO2、NOx、CO排放的实验研究和运行结果令人满意,但对HCl、二恶英及重金属排放还需要进一步研究.试验及实际运行结果都表明,采用CFB燃烧装置对MSW进行焚烧处理是切实可行的,它将是未来解决MSW问题的重要手段.     

Suppressing effect of goethite on PCDD/F and HCB emissions from plastic materials incineration

Polyethylene (PE) and polyvinyl chloride (PVC) are the leading plastics in total production in the world. The incineration of plastic-based materials forms many chlorinated compounds, such as polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs). In this study the addition of goethite (alpha-FeOOH) was investigated to determine its suppressing effect on the emission of PCDD/Fs and hexachlorobenzene (HCB) during the combustion of wastes containing PE and PVC. Goethite was being considered since it acts as a dioxin-suppressing catalyst during incineration. Results showed that incorporation of goethite greatly reduced the generation of PCDD/Fs and HCB in the exhaust gas and fly ash. The concentration of PCDD/Fs in flue gas decreased by 45% for lab-scale and 52% for small incinerator combustion experiments, where the goethite ratios in feed samples were 0.54% and 0.34%, respectively. Under the same conditions, the concentration of HCB in flue gas decreased by 88% and 62%, respectively. The present study showed a possible mechanism of the suppressing effect of the goethite for PCDD/F formation. It is likely that iron chlorides react with particulate carbon to form organo-chlorine compounds and promote PCDD/F formation in the gas phase. XRD analysis of combustion ash revealed that the goethite was partially dehydrated and converted to alpha-Fe(2)O(3) and Fe(3)O(4) but no iron chlorides formation. Therefore the goethite impregnated plastics can contribute the reduction of PCDD/Fs and HCB in the exhaust gas during incineration of MSW.     

Ambient air concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans in Ohio: Sources and health risk assessment

PCDD and PCDF were measured in air samples collected in Ohio in 1987. No 2,3,7,8-TCDD was detected in any of the samples with a detection limits of less than 240 fg/m³. Using a chemical mass balance model applied to PCDD/PCDF congener group profiles, major potential sources of these compounds to the atmosphere in Ohio were determined to be municipal solid waste combustion, and sewage sludge combustion. Cancer risk calculations for inhalation of PCDD/PCDF in ambient air in Ohio are approximately 10–6. Given the current knowledge of the health effects of exposure to PCDD/PCDF in air, there is no appreciable risk to public health for the levels of these compounds found in ambient air in Ohio.     

Assessment of emissions and removal of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) at start-up periods in a hazardous waste incinerator

A study was conducted to observe the changes in polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) levels and congener profiles in the flue gas of a hazardous waste incinerator during two start-up periods. Flue gas samplings were performed simultaneously through Air Pollution Control Devices (APCDs) (including boiler outlet, electrostatic precipitator (ESP) outlet, wet scrubbers (WS) outlet, and activated carbon (AC) filter outlet) in different combustion temperatures during a planned cold (long) start-up and an unplanned warm (short) start-up. The results showed that PCDD/F concentrations could be elevated during the start-up periods up to levels 3–4 times higher than those observed in the normal operation. Especially lower combustion temperatures in the short start-ups may cause high PCDD/F concentrations in the raw flue gas. Assessment of combustion temperatures and Furans/Dioxins values indicated that surface-catalyzed de novo synthesis was the dominant pathway in the formation of PCDD/Fs in the combustion units. PCDD/F removal efficiencies of Air Pollution Control Devices suggested that formation by de novo synthesis existed in ESP also when in operation, leading to increase of gaseous phase PCDD/Fs in ESP. Particle-bound PCDD/Fs were removed mainly by ESP and WS, while gaseous phase PCDD/Fs were removed by WS, and more efficiently by AC filter.

Implications: This paper evaluates PCDD/F emissions and removal performances of APCDs (ESP, wet scrubbers, and activated carbon) during two start-up periods in an incinerator. The main implications are the following: (1) start-up periods increase PCDD/F emissions up to 2–3 times in the incinerator; (2) low combustion temperatures in start-ups cause high PCDD/F emissions in raw gas; (3) formation of PCDD/Fs by de novo synthesis occurs in ESP; (4) AC is efficient in removing gaseous PCDD/Fs, but may increase particle-bound ones; and (5) scrubbers remove both gaseous and particle-bound PCDD/Fs efficiently.     

The dioxin/POPs legacy of pesticide production in Hamburg: Part 2—waste deposits and remediation of Georgswerder landfill

α-HCH, β-HCH, and γ-HCH (lindane) were listed as persistent organic pollutants in the Stockholm Convention. Therefore, they need to be globally addressed including the wastes remaining from historic use and production. While at most lindane production sites the unintentionally produced 85 % HCH waste isomers have been deposited, at a former pesticide factory in Hamburg-Moorfleet HCH waste isomers have been recycled from 1953 to 1984 by thermal decomposition to chlorobenzenes and resulted in high polychlorinated dibenzo-p-dioxin/polychlorinated dibenzofuran (PCDD/PCDF)-contaminated residues. The management of the PCDD/PCDF-contaminated waste from the former pesticide factory in Hamburg has been assessed and quantified. Based on past accredited PCDD/PCDF measurements, the registered 3,700 tonnes of disposed thermal HCH decomposition residue contained 333 to 854 kg of PCDD/PCDF toxicity equivalent (I-TEQ) in 53–102 tonnes total sum of PCDD/PCDF. The wastes have been deposited together with other wastes in landfills in Hamburg and other parts of Germany. For the Georgswerder landfill (Hamburg), where approximately 50 % of the PCDD/PCDF is disposed, current and previous situation and remediation activities are described. While PCDD/PCDF leaching from the landfill is controlled and incinerated, more water soluble organochlorines (vinyl chloride, cis-1,2-dichlorethene, chlorobenzenes) and benzene remain as a challenge for groundwater management. A comprehensive aftercare program has been established and will need to be operated by future generations including renewal of containment systems. Former lindane/HCH productions need—in addition to HCH deposits—to be assessed for possible recycling practice of HCH and related PCDD/PCDF-containing deposits. This could systematically be addressed within the Stockholm Convention implementation.     

Atmospheric mercury emissions from waste combustions measured by continuous monitoring devices

Atmospheric mercury emissions have attracted great attention owing to adverse impact of mercury on human health and the ecosystem. Although waste combustion is one of major anthropogenic sources, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated atmospheric emissions of speciated mercury from the combustions of municipal solid wastes (MSW), sewage treatment sludge (STS), STS with waste plastics, industrial waste mixtures (IWM), waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form at the inlet side of air pollution control devices in all combustion cases. Its concentration was 2.0-70.6 times larger than elemental mercury concentration. In particular, MSW, STS, and IWM combustions emitted higher concentration of reactive gaseous mercury. Concentrations of both gaseous mercury species varied greatly for all waste combustions excluding woody waste. Variation coefficients of measured data were nearly equal to or more than 1.0. Emission factors of gaseous elemental mercury, reactive gaseous mercury, and total mercury were calculated using continuous monitoring data. Total mercury emission factors are 0.30 g-Hg/Mg for MSW combustion, 0.21 g-Hg/Mg for STS combustion, 0.077 g-Hg/Mg for STS with waste plastics, 0.724 g-Hg/Mg for industrial waste mixtures, 0.028 g-Hg/Mg for waste plastic combustion, and 0.0026 g-Hg/Mg for woody waste combustion. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.     

Formation of PCDD/PCDF

One option of recycling used contaminated packaging is to recover its high energy content. This can be performed in a normal multi-fuel power plant by co-combustion of packaging-derived fuel (PDF) or refuse-derived fuel (RDF) with fossil fuels, such as coal or peat. This work includes the results of 17 co-combustion tests and an evaluation of the results by the Principal Component Analysis (PCA) and the Partial Least Squares Projections to Latent Structures (PLS). PCA and PLS calculations showed that especially Pb, but also Cr, and Cu correlated with lower chlorinated furans (PCDFs) in the fly ash. Correlation between Sn and lower chlorinated dioxins (PCDDs) in the fly ash was also noticed. CO and PAH emission in the flue gas correlated with total PCDD/Fs in the flue gas. In a real full-scale combustion process, a single parameter in fuel, flue gas or a combustion parameter did not provide a guide to PCDD/F formation or to a level of the total PCDD/F emission, but correlations between different parameters and PCDD/Fs could be found. Although PDFs and RDF had catalytic heavy metals and chlorine, the co-combustion results showed that they can be co-combusted with peat and coal in a fluidized-bed boiler at least up to 26 % with very low total PCDD and PCDF emissions.     

The role of bio-mechanical treatments of waste in the dioxin emission inventories

PCDD/Fs are one of the most studied molecules in the world because of their toxicity. In the last years the toxicity of these compounds has been analyzed in details. For years PCDD/F inventories have pointed out the significant role of municipal solid waste (MSW) incinerators in the overall balance. Recently, thanks to new regulations on PCDD/F emissions, in a few countries this scenario is changing: it can be demonstrated that modern MSW incinerators can play a secondary role even if the percentage of MSW sent to combustion has increased. In the latest inventories an unconventional source of PCDD/F has appeared: in nineties some biogas characterizations have demonstrated that there is a release of PCDD/F from MSW sanitary landfills. In addition, the combustion of collected biogas can generate not negligible amounts of PCDD/F. A new question can be put: does the MSW contribute with other management options to the overall balance of PCDD/F? The present work points out that a detailed inventory should take into account also the PCDD/F release from bio-mechanical treatment plants (both composting and bio-drying/bio-stabilization plants). However the contribution from this option is secondary when it is compared with the one from old MSW incinerators.     

PCDD/Fs emissions inventory in the Lombardy Region: results and uncertainties

The results of an assessment study of both industrial and non-industrial dioxin and furan (PCDD/Fs) emissions in the Lombardy Region (Italy) are outlined below. The main data source refer to 1997, and are compiled from the Lombardy Emissions Inventory (developed under the framework of the Regional Air Quality Plan) together with documented emissions factors available. Due to the uncertain nature of the emissions assessment, results are provided as a most probable value within a given range. Total PCDD/Fs emissions in Lombardy average 33 g I-TEQ y(-1), ranging from minimum 13 g I-TEQ y(-1) to maximum 88 g I-TEQ y(-1). The main PCDD/Fs sources are waste incineration, electric arc furnace for steel production, vehicle diesel combustion and residential wood combustion. Incineration emission factors are expected to decrease over the period 2005-2010, in compliance with legal requirements. This will prioritize control over the remaining main PCDD/Fs contributors. Due to limited information available concerning this data, the accuracy of which is uncertain, further research is needed to evaluate the future role of these sources.     

Status of PCDD/F-emission control in Germany on the basis of the current legislation and strategies for further action

The protection of environment from polychlorinated dibenzodioxin and -furan (PCDD/F) impacts, caused by a heterogeneous spectrum of thermal stationary sources and several others in chemical industry, bases on a comprehensive legislation in Germany. The results of this emission reduction strategy are presented by emission inventories for stationary, mainly industrial sources comparing in this paper data for emissions between 1994 and 2001. These results show that the implementation of best available techniques (BAT) at industrial sources for PCDD/F-reduction has been nearly fully exhausted at nearly all relevant sources and extensive overall emission reductions were achieved by the end of the 1990s. Further reductions for PCDD/F are needed for specific sources in metallurgical industries, especially sinter plants, and for domestic furnaces only. For coplanar PCBs (co-PCBs) almost no emission data are available from German sources; a few data from measurements of co-PCB have been published from two waste incineration plants. These measurements show that the emission limit value of 0.1 ng TEQ/m3 is not exceeded by co-PCBs in the waste gas in addition to the background PCDD/F concentration. As a consequence from the new appraisals for toxicity equivalences (TEQ) and tolerable daily intakes (TDI) of the World Health Organisation the Federal Environmental Agency in Germany discusses a level of 1 pg WHO TEQ/(kg(bw) d) as an acceptable limit value for adult's burden, taking into account, that this value is too much for children in the pre- and post-natal age and further action for PCDD/F- and co-PCB reduction is needed for the last sensitive group. As a summary can be reported that PCDD/F and co-PCB intakes into the nutrition chain could not have their origin from stationary industrial sources mainly. More attention should be given to more diffuse source such as residential combustion and others, which are more directly connected to the nutrition chain, like green food drying. Important effects could be expected by restrictions of PCDD/F impacts by regulations for control of feed, feed components and compounds feed for pigs and cattle.     

Response surface models for the formation of PCDD and PCDF in a pilot plant combustion of MSW

Experimental data on PCDD and PCDF emissions in raw gases from municipal solid waste combustion in a pilot plant were processed by Response Surface models to gain information on process parameter values which minimize both the total PCDD/PCDF concentrations and those of a selected congener group.