Oxidation of MCPA and 2,4-D by UV radiation, ozone, and the combinations UV/H2O2 and O3/H2O2

The phenoxyalkyl acid derivative herbicides MCPA (4-chloro 2-methylphenoxyacetic acid) and 2,4-D (2,4-dichlorophenoxyacetic acid) were oxidized in ultrapure water by means of a monochromatic UV irradiation and by ozone, as well as by the combinations UV/H2O2 and O3/H2O2. In the direct photolysis of MCPA, the quantum yield at 20 degrees C was directly evaluated and a value of 0.150 mol Eins(-1) was obtained in the pH range 5-9, while a lower value of 0.41 x 10(-2) mol Eins(-1) was determined at pH=3. Similarly, for 2,4-D a value of 0.81 x 10(-2) mol Eins(-1) was deduced, independent of the pH of work. The influence of the additional presence of hydrogen peroxide was established in the combined process UV/H2O2, and the specific contribution of the radical pathway to the global photo-degradation was evaluated. The oxidation by ozone and by the combination O3/H2O2 was also studied, with the determination of the rate constants for the reactions of both herbicides with ozone and hydroxyl radicals at 20 degrees C. These rate constants for the direct reactions with ozone were 47.7 and 21.9 M(-1) s(-1) for MCPA and 2,4-D respectively, while the found values for the rate constants corresponding to the radical reactions were 6.6 x 10(9) and 5.1 x 10(9) M(-1) s(-1).     

Removal of selected endocrine disrupting chemicals and personal care products in surface waters and secondary wastewater by ozonation

This study investigated the removal of parabens, N,N-diethyl-m-toluamide (DEET), and phthalates by ozonation. The second-order rate constants for the reaction between selected compounds with ozone at pH 7 were of (2.2 +/-0.2) X 10(6) to (2.9 +/-0.3) X 10(6) M 1/s for parabens, (2.1+/- 0.3) to (3.9 +/-0.5) M-1/s for phthalates, and (5.2 +/-0.3) M-1/s for DEET. The rate constants for the reaction between selected compounds with hydroxyl radical ranged from (2.49 +/-0.06) x 10(9) to (8.5 +/-0.2) x 10(9) M-1/s. Ozonation of selected compounds in secondary wastewater and surface waters revealed that ozone dose of 1 and 3 mg/L yielded greater than 99% depletion of parabens and greater than 92% DEET and phthalates, respectively. In addition, parabens were found to transform almost exclusively through the reaction with ozone, while DEET and phthalates were transformed almost entirely by hydroxyl radicals (.OH).     

臭氧氧化法处理焦化废水生化出水的反应动力学

对臭氧氧化去除焦化废水生化出水COD的反应动力学及其影响因素进行了实验研究，结果表明，在臭氧投加量为8．50mg／min，反应温度为20＇E和初始pH为10．61条件下，对COD的降解符合表观一级反应动力学模型，其相关系数R。=0．9991，表观反应速率常数k。。=1．01×10^-3s-1。该条件下，臭氧氧化对COD的降解主要来源于高活性羟基自由基的强氧化作用。在不同的臭氧投加量（4．25～12．75mg／min）、不同的反应温度（10～40℃）和不同的初始pH（3．76～12．53）下，COD的降解也同样遵循一级反应动力学规律。随着臭氧投加量的增大，COD降解的表观反应速率常数从（0．554×10^-3）s-1增加到（1．06×10＆-3）s-1；随着反应温度的升高，表观反应速率常数从（0．427×10^-3）s-1增加到（1．40×10-3）s-1，温度越高反应速率提高的幅度却越小；在初始pH3．76～10．61范围内，表观反应速率常数从（0．218×10^-3）s-1增加到（1．01×10^-3）s-1，在初始pH为12．53时表观反应速率常数下降到（0．857×10^-3）s-1。     

Degradation of octylphenol and nonylphenol by ozone - part I: direct reaction

This aqueous reaction between ozone and two alkylphenols (APs), namely octylphenol (OP) and nonylphenol (NP), has been investigated. Both compounds are important endocrine disrupting chemicals, which arise from the biodegradation of alkylphenol ethoxylates and are often found at relatively high concentrations in wastewater effluents. In this paper the results of an experimental study are presented which provide values for the reaction rate constants between molecular ozone and undissociated OP and NP, and overall reaction rate constants for the degradation of the two APs at pH values in the range of 7-9. The kinetic rate constants for OP and NP degradation by molecular ozone were 4.33(+/-0.18) x 10(4) and 3.90(+/-0.10) x 10(4) M(-1) s(-1), and the reaction stoichiometry was similar in both cases and equal to approximately 1.3:1 ([O3]:[AP]). The overall second order reaction rate constants for the two APs increased significantly with increasing pH, which is believed to be mainly due to the increasing influence of indirect radical reaction with increasing pH; this aspect is considered in more detail in a companion paper. A preliminary investigation of the reaction mechanism suggests that an initial product of ozonation is hydroxyl-alkyl phenol.     

Degradation of octylphenol and nonylphenol by ozone - part II: indirect reaction

The indirect reaction of octylphenol (OP) and nonylphenol (NP) with hydroxyl radicals (*OH) during ozonation was investigated at pH values ranging from 6 to 9. A parameter Rct, representing the ratio of the *OH-exposure to the ozone-exposure, was measured using a method involving a low concentration of p-chlorobenzoic acid as a *OH-probe compound during the ozonation. By assuming that Rct is a constant value at a given pH, the second order rate constants of the alkylphenol reaction with hydroxyl radicals were determined as 1.4(+/-0.2) x 10(10) and 1.1(+/-0.2) x 10(10) M(-1) s(-1) for OP and NP, respectively. The proportions of each alkylphenol degraded by direct molecular ozone reaction and indirect hydroxyl radical reaction were predicted at different pH values. The contribution of indirect *OH reactions with each AP was found to represent over 50% of the total degradation for pH approximately 7, and the contribution increases substantially with pH>7.     

Ozonation of aqueous solution of alpha endosulfan

Ozonation of alpha endosulfan and the effects of some parameters such as pH, temperature and partial pressure on ozonation were investigated and the kinetic constants were calculated in this study. Alpha endosulfan solutions were ozonated in a lab-scale semi-batch reactor under variable experimental conditions. Increase in dissolved ozone concentration had a positive effect on oxidation rate. Alpha endosulfan could be removed up to 94% at pH 4 for an ozonation time of 60 minutes. The oxidation reaction was found to be of second order and of first order with respect to both ozone and alpha endosulfan. The temperature dependent reaction expression of alpha endosulfan was obtained as kd = (1.889 exp(- 2.21 x 10(-3)/T). It was concluded that, although the rate of reaction was lower than the rate of other pesticide oxidation reported in the literature. alpha endosulfan presented an obvious reaction to ozonation.     

Mineralization of C.I. Reactive Yellow 84 in aqueous solution by sonolytic ozonation

The operational parameters and mechanism of mineralization of C.I. Reactive Yellow 84 (RY84), one of the azo dyes, in aqueous solution were investigated using sonolytic ozonation (US/O(3) oxidation). Of the pseudo-first-order degradation rate constants of TOC reduction, 9.0 x 10(-4), 7.3 x 10(-3) and 1.8 x 10(-2)min(-1) were observed with US, O3, and a combination of US and O3, respectively. These results illustrate that ozonation combined with sonolysis for removal of TOC is more efficient than ozonation alone or ultrasonic irradiation alone without considering the operating costs. With the initial pH value at 10.0, the ozone dose at 4.5 g h(-1), the energy density of ultrasound at 176 W l(-1), and the initial concentration of RY84 at 100 mg l(-1), the extent of mineralization measured as TOC loss was maximized. The variation of the concentrations of related ions (oxalate, formate, acetate, NO3(-), NO2(-), NH4(+), Cl(-), and SO4(2-)) during the reaction process was monitored. Other organic intermediates detected by GC/MS were N-methyleneaniline, phthalic acid, 4-hydroxyphthalic acid, isocyanatobenzene, aniline, 4-iminocyclohexa-2,5-dien-1-one, butene diacid and urea. Based on these findings, a tentative degradation pathway was proposed.     

Catalytic ozonation of 2,4-dichlorophenoxyacetic acid using alumina in the presence of a radical scavenger

Using a laboratory-scale mixed reactor, the performance of alumina in degrading 2,4-Dichlorophenoxyacetic acid with ozone in the presence of tert-butyl alcohol radical scavenger was studied. The operating variables investigated were the dose of alumina catalyst and solution pH. Results showed that using ozone and alumina leads to a significant increase in 2,4-D removal in comparison to non-catalytic ozonation and adsorption processes. The observed reaction rate constants (k(obs)) for 2,4-D during ozonation were found to increase linearly with increasing catalyst dose. At pH 5, the k(obs) value increased from 19.3 to 26 M(-1) s(-1) and 67 M(-1) s(-1) when varying the alumina dose from 1 to 2 and 4 g L(-1), respectively. As pH was increased, higher reaction rates were observed for both non-catalytic ozonation and catalytic ozonation processes. Thus, at pH 3 and using a catalyst dose of 8 g L(-1), the k(obs) values for non-catalytic ozonation and catalytic ozonation processes were 3.4 and 58.9 M(-1) s(-1), respectively, whereas at pH 5 reaction rate constants of 6.5 and 128.5 M(-1) s(-1) were observed, respectively. Analysis of total organic carbon suggested that catalytic ozonation with alumina achieved a considerable level of mineralization of 2,4-D. Adsorption of 2,4-D on alumina was found to play an important role in the catalytic ozonation process.     

Ozonation of Procaine Penicillin G formulation effluent Part I: Process optimization and kinetics

Ozonation characteristics of synthetic Procaine Penicillin G (PPG) formulation effluent were investigated in a semi-batch ozone reactor at different pH (3, 7 and 12), ozone feed rates (600-2600 mg h-1) and COD values (200-600 mg l-1). Ozonation of aqueous PPG effluent resulted in 37 (82)% COD removal after 60 (120) min ozonation when the reaction pH was kept constant at pH=7.900 mg l-1 (corresponding to 50% of the total introduced) ozone was absorbed during a reaction period of 1 h. The effects of increasing the applied ozone dose and the initial COD on the COD abatement rates of PPG effluent were also studied. Results have indicated that increasing the ozone dose and decreasing the COD content both have positive effects on COD removal rates. The significant contribution of the free radical (.OH) reaction pathway to PPG ozonation could be traced using tert-butyl alcohol as the .OH probe compound at varying concentrations. The bimolecular reaction rate constants for the direct reaction of PPG with ozone were found as 152 and 2404 M-1 h-1 at pH=3 and 7, respectively, using the gas phase ozone partial pressures determined from of the outlet gas stream analysis. It could be demonstrated that ozone decomposition to free radicals being triggered by increasing the pH from 3 to 7 is essential for the rate enhancement of PPG effluent ozonation.     

A kinetic study on oxidation of pentachlorophenol by ozone

The kinetics of pentachlorophenol (PCP) ozonation in terms of the gaseous O3 and dissolved PCP concentrations has been investigated. When the O3 concentration in the gas phase was in the range of 10 to 40 g O3/m3, the O3 dissolved for a short time period was proportional to the gaseous O3 concentration. In this range, the ozonation reaction was first order for each reactant and the overall reaction was second order. At 25 degrees C, in an aqueous solution, the reaction rate constant was estimated to be 10.048 L/mol.sec. The reaction rate was much greater than the mass-transfer rate, indicating that the reaction of O3 and PCP was an interface reaction on the surface of gaseous O3 bubbles. The final product of the PCP ozonation was oxalic acid, with the carbon yield of the reaction being 59.4%. The ozonation of PCP in the aqueous solution was not a radical reaction but a direct reaction between O3 and PCP molecules under the conditions investigated in this study, since O3 has a high selectivity toward PCP. The reaction rate increased with the reaction temperature up to 35 degrees C but decreased at temperatures greater than 35 degrees C due to the decreased solubility of O3. The addition of H2O2 did not increase the reaction rate significantly.     

Kinetic assessment of the potassium ferrate(VI) oxidation of antibacterial drug sulfamethoxazole

Sulfamethoxazole (SMX), a worldwide-applied antibacterial drug, was recently found in surface waters and in secondary wastewater effluents, which may result in ecotoxical effects in the environment. Herein, removal of SMX by environmentally-friendly oxidant, potassium ferrate(VI) (K(2)FeO(4)), is sought by studying the kinetics of the reaction between Fe(VI) and SMX as a function of pH (6.93-9.50) and temperature (15-45 degrees C). The rate law for the oxidation of SMX by Fe(VI) is first-order with respect to each reactant. The observed second-order rate constant decreased non-linearly from 1.33+/-0.08 x 10(3) M(-1)s(-1) to 1.33+/-0.10 x 10(0) M(-1)s(-1) with an increase of pH from 7.00 to 9.50. This is related to protonation of Fe(VI) (HFeO(4)(-) <==> H(+) + FeO(4)(2-); pK(a,HFeO(4)) = 7.23) and sulfamethoxazole (SH <==> H(+) + S(-); pK(a,SH)=5.7). The estimated rate constants were k(11)(HFeO(4)(-) + SH) = 3.0 x 10(4) M(-1)s(-1), k(12)(HFeO(4)(-) + S(-)) = 1.7 x 10(2) M(-1)s(-1), and k(13) (FeO(4)(2-) + SH) = 1.2 x 10(0) M(-1)s(-1). The energy of activation at pH 7.0 was found to be 1.86+/-0.04 kJ mol(-1). If excess potassium ferrate(VI) concentration (10 microM) is used than the SMX in water, the half-life of the reaction using a rate constant obtained in our study would be approximately 2 min at pH 7. The reaction rates are pH dependent; thus, so are the half-lives of the reactions. The results suggest that K(2)FeO(4) has the potential to serve as an oxidative treatment chemical for removing SMX in water.     

Rapid reductive dechlorination of atrazine by zero-valent iron under acidic conditions

The dechlorination of atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine) via reaction with metallic iron under low-oxygen conditions was studied using reaction mixture pH values of 2.0, 3.0, and 3.8. The pH control was achieved through addition of sulfuric acid throughout the duration of the reaction. The lower the pH of the reaction mixture, the faster the degradation of atrazine. The surface area of the sulfuric acid-treated iron particles was 0.31 (+/- 0.01) m2 g-1 and the surface area normalized initial pseudo-first order rate constants (kSA, where rate = kSA x (surface area/l) x [Atrazine]) at pH values of 2.0, 3.0, and 3.8 were equal to, respectively, 3.0 (+/- 0.4) x 10(-3) min-1 m-2 l, 5 (+/- 3) x 10(-4) min-1 m-2 l, and 1 (+/- 1) x 10(-4) min-1 m-2 l. The observed products of the degradation reaction were dechlorinated atrazine (2-ethylamino-4-isopropylamino-1,3,5-triazine) and possibly hydroxyatrazine (2-ethylamino-4-isopropylamino-6-hydroxy-s-triazine). Triazine ring protonation may account, at least in part, for the observed effect of pH on atrazine dechlorination via metallic iron.     

Observations of 2,4,6-trichlorophenol degradation by ozone

The aqueous reactivity of 2,4,6-trichlorophenol (TCP) with ozone has been studied at laboratory-scale using a simple gas bubble/liquid contacting system. Degradation rate constants were measured directly and found to be 7.6 and 77.2 M(-1)s(-1) at pH 2 and 7.5, respectively. At pH 7.5, 10 min of ozonation ( identical with 15 mM ozone consumption) achieved a 90% degradation of TCP, which corresponded to the release of approximately 2 mol Cl(-) per mol TCP. The presence of hydrogen peroxide in solution did not significantly increase the TCP degradation but increased the overall dechlorination to 2.7 mol Cl(-) per mol TCP. The presence of humic acid (HA) in solution was found to enhance the degradation rate of TCP at low relative HA concentrations (<0.6 g/g HA:TCP), but to reduce the rate at higher HA concentrations.     

Kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE)

The kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE) in aqueous solutions at various pH, temperature, oxidant concentration and ionic strength levels was studied. The MTBE degradation was found to follow a pseudo-first-order decay model. The pseudo-first-order rate constants of MTBE degradation by persulfate (31.5 mM) at pH 7.0 and ionic strength 0.11 M are approximately 0.13 x 10(-4), 0.48 x 10(-4), 2.4 x 10(-4) and 5.8 x 10(-4) S(-1) at 20, 30, 40 and 50 degrees C, respectively. Under the above reaction conditions, the reaction has an activation energy of 24.5 +/- 1.6 kcal/ mol and is influenced by temperature, oxidant concentration, pH and ionic strength. Raising the reaction temperature and persulfate concentration may significantly accelerate the MTBE degradation. However, increasing both pH (over the range of 2.5-11) and ionic strength (over the range of 0.11-0.53 M) will decrease the reaction rate. Reaction intermediates including tert-butyl formate, tert-butyl alcohol, acetone and methyl acetate were observed. These intermediate compounds were also degraded by persulfate under the experimental conditions. Additionally, MTBE degradation by persulfate in a groundwater was much slower than in phosphate-buffer solutions, most likely due to the presence of bicarbonate ions (radical scavengers) in the groundwater.     

Bioconcentration factor of relatively low concentrations of chlorophenols in Japanese medaka

Bioconcentration factors (BCF) for pentachlorophenol (PCP) and 2,4-dichlorophenol (2,4-DCP) in Japanese medaka (Oryzias latipes) were determined at five different concentrations of the chemicals, between 0.1 and 10 microg/l (PCP), 0.3 and 30 microg/l (2,4-DCP), in the ambient water. Medaka were exposed to each chemicals in a continuous-flow system during the embryonic development period and 60 days after hatching from eggs collected in the laboratory. Both the exposure time and the aqueous concentrations are much more realistic and closer to natural aquatic environments than those used in conventional BCF studies. The BCF values of PCP were from (4.9+/-2.8)x10(3) at the aqueous concentration of 0.074+/-0.028 microg/l to (2.1+/-1.4)x10(3) at 9.70+/-0.56 microg/l. The BCF value of 2,4-DCP were from (3.4+/-3.0)x10(2) at 0.235+/-0.060 microg/l to 92+/-27 at 27.3+/-1.6 microg/l. Generally, BCF values increased as the aqueous concentrations of PCP or 2,4-DCP decreased. This finding suggests that a relatively low and realistic aqueous concentration of these compounds is necessary to more accurately determine their BCF values in natural aquatic environments. Conventional BCF experiments at higher aqueous concentrations may underestimate the BCF values.     

Ozonation of oxytetracycline and toxicological assessment of its oxidation by-products

Antibiotic formulation effluents are well known for their difficult elimination by traditional bio-treatment methods and their important contribution to environmental pollution due to its fluctuating and recalcitrant nature. In the present study the effect of ozonation on the degradation of oxytetracycline (OTC) aqueous solution (100mgl(-1)) at different pH values (3, 7 and 11) was investigated. Ozone (11mgl(-1) corresponds the concentration of ozone in gas phase) was chosen considering its rapid reaction and decomposition rate. The concentration of oxytetracycline, chemical oxygen demand (COD), biochemical oxygen demand (BOD) and BOD5/COD ratio were the parameters to evaluate the efficiency of the ozonation process. In addition, the toxic potential of the OTC degradation was investigated by the bioluminescence test using the LUMIStox 300 instrument and results were expressed as the percentage inhibition of the luminescence of the marine bacteria Vibrio fischeri. The results demonstrate that ozonation as a partial step of a combined treatment concept is a potential technique for biodegradability enhancement of effluents from pharmaceutical industries containing high concentration of oxytetracycline provided that the appropriate ozonation period is selected. At pH 11 and after 60min of ozonation of oxytetracycline aqueous solutions (100 and 200mgl(-1)) the BOD5/COD ratios were 0.69 and 0.52, respectively. It was also shown that COD removal rates increase with increasing pH as a consequence of enhanced ozone decomposition rates at elevated pH values. The results of bioluminescence data indicate that first by-products after partial ozonation (5-30min) of OTC were more toxic than the parent compound.     

Catalytic ozonation of 2,4-Dichlorophenoxyacetic acid using alumina in the presence of a radical scavenger

Using a laboratory-scale mixed reactor, the performance of alumina in degrading 2,4-Dichlorophenoxyacetic acid with ozone in the presence of tert-butyl alcohol radical scavenger was studied. The operating variables investigated were the dose of alumina catalyst and solution pH. Results showed that using ozone and alumina leads to a significant increase in 2,4-D removal in comparison to non-catalytic ozonation and adsorption processes. The observed reaction rate constants (k_obs ) for 2,4-D during ozonation were found to increase linearly with increasing catalyst dose. At pH 5, the k_obs value increased from 19.3 to 26 M^?1 s^?1 and 67 M^?1 s^?1 when varying the alumina dose from 1 to 2 and 4 g L^?1, respectively. As pH was increased, higher reaction rates were observed for both non-catalytic ozonation and catalytic ozonation processes. Thus, at pH 3 and using a catalyst dose of 8 g L^?1, the k_obs values for non-catalytic ozonation and catalytic ozonation processes were 3.4 and 58.9 M^?1 s^?1, respectively, whereas at pH 5 reaction rate constants of 6.5 and 128.5 M^?1 s^?1 were observed, respectively. Analysis of total organic carbon suggested that catalytic ozonation with alumina achieved a considerable level of mineralization of 2,4-D. Adsorption of 2,4-D on alumina was found to play an important role in the catalytic ozonation process.     

Influence of sorption to dissolved humic substances on transformation reactions of hydrophobic organic compounds in water. Part II: hydrolysis reactions

The effect of dissolved humic acid (HA) on two types of hydrolysis reactions was investigated: (I) dehydrochlorination of gamma-hexachlorocyclohexane (HCH) and 1,1,2,2-tetrachloroethane (TeCA) as a reaction involving hydroxide ions (OH(-)) and (II) hydrolysis of 1-octyl acetate (OA) which is catalyzed by H(+) at the applied pH value (pH 4.5). The rate of TeCA hydrolysis was not affected by addition of 2 g l(-1) of HA at pH 10 (k' = 0.33 h(-1)) but HCH hydrolysis was significantly inhibited (k' = 4.6 x 10(-3) h(-1) without HA and 2.8 x 10(-3)h(-1) at 2 g l(-1) HA). HCH is sorbed by 51% whereas TeCA sorption is insignificant at this HA concentration. Sorbed HCH molecules are effectively protected due to electrostatic repulsion of OH(-) by the net negative charge of the HA molecules. In contrast, OA hydrolysis at pH 4.5 (k' = 1.6 x 10(-5) h(-1)) was drastically accelerated after addition of 2 g l(-1) HA (k' = 1.1 x 10(-3) h(-1)). The ratio of the pseudo-first-order rate constants of the sorbed and the freely dissolved ester fraction is about 70. H(+) accumulation in the microenvironment of the negatively charged HA molecules was suggested to contribute to the higher reaction rate for the sorbed fraction in case of this H(+)-catalyzed reaction. Analogous effects from anionic surfactants are known as micellar catalysis.     

1990 Government Agencies Directory

ABSTRACT

The kinetics of pentachlorophenol (PCP) ozonation in terms of the gaseous O₃ and dissolved PCP concentrations has been investigated. When the O₃ concentration in the gas phase was in the range of 10 to 40 g O₃/m³, the O₃ dissolved for a short time period was proportional to the gaseous O₃ concentration. In this range, the ozonation reaction was first order for each reactant and the overall reaction was second order. At 25 °C, in an aqueous solution, the reaction rate constant was estimated to be 10.048 L/mol-sec. The reaction rate was much greater than the mass-transfer rate, indicating that the reaction of O₃ and PCP was an interface reaction on the surface of gaseous O₃ bubbles. The final product of the PCP ozonation was oxalic acid, with the carbon yield of the reaction being 59.4%. The ozonation of PCP in the aqueous solution was not a radical reaction but a direct reaction between O₃ and PCP molecules under the conditions investigated in this study, since O₃ has a high selectivity toward PCP. The reaction rate increased with the reaction temperature up to 35 °C but decreased at temperatures greater than 35 °C due to the decreased solubility of O₃. The addition of H₂O₂ did not increase the reaction rate significantly.     

Evaluation of photolysis and hydrolysis of atrazine and its first degradation products in the presence of humic acids

Relative importance of hydrolysis and photolysis of atrazine and its degradation products in aqueous solutions with dissolved humic acids (HA) has been assessed under exposure to sunlight and under UV irradiation. Quantum yield for direct photolysis of atrazine at 254 nm was 0.037 mol photon(-1), the reaction order was 0.8. Atrazine, desethylatrazine and desisopropylatrazine converted to their 2-hydroxy analogs with rate constants 0.02-0.08 min(-1) in clear solutions, while addition of HA (300 mg L(-1)) caused a 10-fold increase in rate constants. Hydroxyatrazine was not degraded. No evidence of photo-Fenton reaction was found. Under exposure to solar light, atrazine, desethylatrazine and desisopropylatrazine were converted to 2-hydroxy analogs only at pH 2 because of acid hydrolysis and possible contribution of photolysis. At lower HA concentration, only their light-shielding effect was noticed, while at higher concentrations, HA-catalysed hydrolysis prevailed. Hydroxyatrazine concentration diminished at all pH values in solutions without HA exposed to sunlight.