Determination trace amounts of copper, nickel, cobalt and manganese ions in water samples after simultaneous separation and preconcentration

In the present article, a simple, rapid, sensitive and economical method has been developed for the simultaneous separation and preconcentration of the trace amounts of copper, nickel, cobalt and manganese in water samples by using modified XAD-4 resins. The sorption was quantitative in the pH range 6.0–9.0, whereas quantitative desorption occurred instantaneously with 5.0 mL of 2 M HNO₃, and selected elements have been determined by using flame atomic absorption spectrometry. Dynamic ranges were 0.04–3.5, 0.1–6.0, 0.04–4.5 and 0.04–4.0 μg/mL for copper, nickel, cobalt and manganese, respectively. The detection limits were 9.2, 28.6, 12.3 and 5.7 ng/mL for Cu(II), Ni(II), Co(II) and Mn(II), respectively. The effects of the experimental parameters, including the sample pH, eluent type, interference ions and breakthrough volume, were studied for separation and preconcentration of Cu(II), Ni(II), Co(II) and Mn(II) ions. Determination of these ions in standard samples confirmed that the proposed method has good accuracy. The proposed method was used for the determination of these ions in water samples.     

Synthesis of 2,3-dihydroxynaphthalene-functionalized Amberlite XAD-4 resin: Applications for the separation and preconcentration of trace metal ions prior to their determination by inductively coupled plasma atomic emission spectrometry

A simple, sensitive column solid-phase extraction procedure for separation and preconcentration of Cu(II), Ni(II), Co(II), and Cd(II) in spiked and natural water samples using 2,3-dihydroxynaphthalene-functionalized Amberlite XAD-4 (XAD-4-DHN) chelating resin prior to their determination by inductively coupled plasma atomic emission spectrometry was discussed. The optimum experimental parameters such as pH, volume of sample and eluent, flow-rates of uptake and stripping, and sorption capacity of the chelating resin, were evaluated. The effect of the electrolytes and the cations on the preconcentration of metal ions was also investigated. The chelating resin could be reused for more than 20 cycles of sorption–desorption without any significant change (<1.0%). Recoveries obtained from this method range from 96 to 102% with R.S.D of 2.50 (n = 4). The detection limits for Cu(II), Ni(II), Co(II), and Cd(II) were found to be 1.9, 0.9, 1.2 µg, and 1.4 µg L^?1, respectively. The proposed method was applied for the determination of Cu(II), Ni(II), Co(II), and Cd(II) in spiked, tap water, and river water samples.     

Cloud point extraction of trace cyanide from environmental waters for indirect flame atomic absorption spectrometric determination

A method has been developed for indirect determination of cyanide in environmental waters based on cloud point extraction (CPE), preconcentration and determination by flame atomic absorption spectrometry (FAAS). The method was based on reduction of Cu(II) to Cu(I) in the presence of cyanide and complexation of the produced Cu(I)(CN)₂^? with gallocyanin (GC⁺) as an ion-pairing reagent at pH 4.0, followed by its extraction into polyethyleneglycol mono-p-nonylphenylether (Ponpe 7.5). Selectivity was improved with the use of suitable masking agents. Various factors influencing separation and preconcentration of cyanide have been investigated, and conditions were optimized, allowing determination of cyanide in the range of up to 1.2 mg L^?1 with a detection limit of 0.00045 mg L^?1. The method has been applied to the determination of cyanide in environmental waters, the results being in agreement with those obtained by a reference method.     

Preconcentration of some trace metal ions on coated alumina modified by 1-((6-(-(2-hydroxynaphthalen-1-yl)methyleneamino) hexylimino) methyl) naphthalen-2-ol

A sensitive and efficient method for preconcentration of trace amounts of some metal ions such as Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺, Cr³⁺, and Fe³⁺ ions based on modification of sodium-dodecyl-sulphate (SDS) coated alumina with 1-(6-(-(2-hydroxynaphthalen-1-yl) methyleneamino) hexylimino) methyl) naphthalen-2-ol (HNMAHN) is reported. The method is based on the uptake of these ions following their chelation with HNMAHN and their recovery using a suitable eluent. The influence of parameters such as pH, concentration of ligand and amount of coated alumina, SDS concentration, eluent (type and concentrations), and elution volume on metal ion recoveries are investigated. The preconcentration factor is 150 (10?mL elution volume) for a 1500?mL sample volume. The method has been successfully applied for extraction and determination of these ions content in some real samples. Extraction efficiency is generally >95% with low relative standard deviations between 1.8% and 2.4 %.     

Oxidized multiwalled carbon nanotubes modified with 2-(2-hydroxy-5-nitrophenyl)-4,5-diphenyl imidazole for solid phase extraction and preconcentration of some metal ions

In this work, a new procedure for the enrichment of the trace amount of Cu²⁺, Ni²⁺, Co²⁺, Pb²⁺, Fe²⁺, and Zn²⁺ ions based on the utilization of multiwalled carbon nanotubes (MWCNT) modified with 2-(2-hydroxy-5-nitrophenyl)-4,5-diphenyl imidazole as chelating agent prior to their determination by flame atomic absorption spectrometry has been described. The influence of effective parameters including pH, amount of ligand and MWCNT, composition of eluent, and coexisting ions on recoveries of understudy metal ions was examined. At the optimum pH of 5.0, all metal ions were quantitatively sorbed onto the proposed solid phase and completely desorbed with 8?mL of 5.0?mol?L^?1 HNO₃. The detection limit of Cu²⁺, Co²⁺, Ni²⁺, Pb²⁺, Fe²⁺, and Zn²⁺ ions was 1.7, 2.4, 2.3, 2.9, 2.8, and 1.4?µg?L^?1, while the preconcentration factor was 63 for Cu²⁺ and 94 for the other metal ions and relative standard deviations between 1.8 less than 3.0%. The proposed procedure was applied for the analysis of various samples.     

A simple ligandless microextraction method based on ionic liquid for the determination of trace cadmium in water and biological samples

A simple and efficient ionic liquid-based ligandless microextraction method has been developed for preconcentration of cadmium ions (Cd²⁺) as a step prior to its determination by flame atomic absorption spectrometry (FAAS) with a micro-sample introduction system. In this approach, the ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate [C₄mim][PF₆] and ethanol were used as extractant and dispersive solvents to preconcentrate the Cd²⁺ in different waters, acid digested scalp hair, and nail samples. Some analytical parameters influencing the extraction efficiency of Cd²⁺ and its subsequent determination, including pH, IL volume, dispersant solvent volume, sample volume, temperature, incubation time, and matrix effect, were optimized. Under optimal conditions, the limit of detection (LOD), limit of quantification (LOQ), and enhancement factor (EF) were 0.4 μg L^?1, 1.3 μg L^?1, and 50, respectively. The relative standard deviation (RSD) of 100 μgL^?1 Cd²⁺ was 4.3% (n = 6). The validity of the proposed method was checked by determining Cd²⁺ in certified reference material (TM-25.3 fortified water) and standard addition; the results showed sufficient recovery (>98%) of Cd²⁺ within the certified value. The method was applied for preconcentration and determination of cadmium in waters and biological samples.     

Determination of Au(III) and Pd(II) ions by flame atomic absorption spectrometry in some environmental samples after solid phase extraction

A simple and sensitive solid phase extraction method was developed for simultaneous separation and preconcentration of gold and palladium ions with N-(4-methylphenyl)-2-{[(4-phenyl-5-pyridine-4-yl-4H-1,2,4-triazol-3-yl)thio]acetyl}hydrazine carbo thioamide complex on Amberlite XAD-1180 resin before their determination by flame atomic absorption spectrometry. Some analytical parameters such as HNO₃ concentration of the sample solution, amount of complexing agent, sample volume, eluent type and volume, effects of foreign ions and adsorption capacity of the resin were investigated for quantitative recovery of gold and palladium ions. The effects of some anions and cations were also examined. Under optimum conditions, the detection limits for gold and palladium ions were found to be 0.29 and 0.19 μg L^?1, respectively. The preconcentration factor for gold and palladium was 250. After being validated by standard addition and analysis of standard reference material, the procedure was successfully applied to the analysis of sea and stream water, anodic slime, gold ore, soil and electronic waste.     

Determination of cadmium in water and herbal medicine by Penicillium chrysogenum immobilized on silica gel for flame atomic absorption spectroscopy

Penicillium chrysogenum was immobilized on silica to develop a simple and cost effective method for solid phase extraction of Cd(II) and determination using flame atomic absorption spectrometry (FAAS). The sorbent was characterized by Fourier transform infrared spectroscopy and packed into a column. The conditions for quantitative sorption and desorption of Cd(II) were optimized. The preconcentration factor was 100 while detection limit was 0.61 µg L^?1 with a relative standard deviation of 1.0%. The method was applied for determination of Cd in herbal medicine and tap water.     

Solid phase extraction of trace metals from environmental samples using Amberlite XAD-7 loaded with 2-hydroxy-propiophenone-4-phenyl-3-thiosemicarbazone and determination by inductively coupled plasma–atomic emission spectrometry

A method for the solid phase extraction of trace metals, namely Co, Cu, Pb, Ni and Zn, from environmental and biological samples using column Amberlite XAD-7 loaded with 2-hydroxy-propiophenone-4-phenyl-3-thiosemicarbazone (HPPPTSC) and determination by inductively coupled spectrometry (ICP–AES) has been developed. The reagent has the capacity to form chelate complexes with the metals because of three binding sites in the reagent molecule. The optimum experimental conditions for the quantitative sorption of five metals, pH, effect of flow rate, concentration of eluent, sorption capacity and the effect of diverse ions on the preconcentration of analytes have been investigated. The sorption capacity of the resin has 83, 127, 35, 88 and 85?µmol?g^?1 for Co²⁺, Cu²⁺, Pb²⁺, Ni²⁺ and Zn²⁺, respectively. The preconcentration factors for Co²⁺, Cu²⁺, Pb²⁺, Ni²⁺ and Zn²⁺ were 100, 110, 120, 140 and 150, respectively. The accuracy of the proposed procedure was evaluated by standard reference materials. The achieved results were in good agreement with certified values. The proposed method was applied for the determination of trace metals in river water and plant leaves.     

Preconcentration of cadmium and copper ions on magnetic core–shell nanoparticles for determination by flame atomic absorption

Magnetic core–shell nanoparticles modified by (3-aminopropyl) trimethoxy silane were prepared and used as adsorbent for the extraction and preconcentration of cadmium and copper ions. The ions were desorbed with nitric acid followed by determination with flame atomic absorption spectrometry. The extraction conditions were investigated systematically. The method was applied for the determination of Cd(II) and Cu(II) ions in different water samples. The accuracy was also evaluated through analysis of certified reference material.     

Preconcentration of samarium with modified yeast cells for its determination by atomic emission spectroscopy

A chelating-modified biosorbent is produced by coupling of a dye, procion red, to yeast cells. The resulting modified cells have been characterized by Fourier transform infrared, elemental analysis and thermogravimetric analysis and studied for preconcentration and determination of trace Sm(III). The optimum pH value for sorption of the samarium ions is 6.2. The sorption capacity of functionalized modified yeast cells is 7.2 mg g^?1. Recovery was 99% when Sm(III) was eluted with an aqueous solution of 0.1 mol L^?1 ethylenediaminetetraacetic acid. Scatchard analysis suggested that binding sites were homogeneous. The equilibrium data were analyzed using Langmuir, Freundlich, Temkin, and Redlich–Peterson isotherm models, and the respective constants were determined as 1.0 (L mg^?1), 2.9 [(mg g^?1) (L mg^?1)^1/n], 2.4 × 10⁸ (L g^?1), and 30 (dm³ g^?1) at 20 °C. The method was applied for an Sm(III)-containing sample of ceramic industry effluent.     

Biosorption of cadmium and nickel ions using marine macrophyte,Cymodocea nodosa

ABSTRACT

Seagrass (Cymodocea nodosa) ability to remove cadmium and nickel ions from single metal solutions was investigated in the present study. Metal ions were measured in the solution using an atomic absorption spectrophotometer. Various operational parameters (initial pH, biomass dose, metal ion concentration, and contact time) were tested and found to affect the uptake capacity of Cd (II) and Ni (II). More than 70% of biosorption capacity occurred in the first few minutes for both metal ions. The pseudo-second-order kinetic model and the Langmuir model were found to best fit the experimental data of Cd (II) and Ni (II) biosorption. The maximum uptake capacity (q_max) was 11.6 and 16.7?mg.g^?1 for Cd (II) and Ni (II), respectively. The biosorbent was characterised using Fourier transform infrared spectrometry (FTIR), scanning electron microscope (SEM), and energy-dispersive X-ray spectroscopy (EDX). The infrared spectrum demonstrated that hydroxyl, carboxyl, and phenolic functional groups are the major binding sites for Cd (II) and Ni (II) metals. The ion exchange mechanism plays an important role during biosorption process as shown in EDX analysis. Our results conclude that marine macrophyte C. nodosa can be used as a low-cost biosorbent for the removal of Cd (II) and Ni (II) in wastewater.     

Online solid phase preconcentration using EGDMA–MAA copolymer for lead determination by FAAS

A Ethylene glycol dimethacrylate (EGDMA) methacrylic acid (MAA) resin was used for preconcentration of lead at trace levels in water samples. For this purpose, a flow-injection, solid phase extraction method was developed for the determination of lead by flame atomic absorption spectrometry. Lead ions were sorbed on a EGDMA–MAA column at pH 4, followed by an elution step using 288 µL of 4.0 M nitric acid solution and determination by flame atomic absorption spectrometry. Optimum conditions for quantitative sorption involving the pH, sample volume, loading and elution flow rates, eluent type, and volume were investigated. A 868-fold enrichment factor could be reached. The detection limit for the water samples, estimated from the noise on the signal obtained for 250 mL of 10 µg L^?1 loaded at 4.9 mL min^?1 was 1.04 µg L^?1. The method was applied for lead determination in river water samples collected in Edirne, Turkey. Recoveries of spiked solutions (10 µg L^?1) to river water samples were quantitative. Finally, the method was validated by the analysis of certified reference material SRM 2704 (Buffalo River Sediment).     

Determination of cobalt by air-assisted liquid–liquid microextraction

Abstract

A rapid and selective technique for extraction, preconcentration and determination of trace amounts of cobalt in water and pharmaceutical samples by air-assisted liquid–liquid microextraction combined with flame atomic absorption spectrometry is proposed. 1-Nitroso-2-naphthol is used as a complexing agent and 1-octanol as an extraction solvent. Parameters relevant for analytical effectivity, i.e. pH of sample solution, concentration of complexing agent, volume of extraction solvent, and number of extraction cycles are optimized using a Box–Behnken design. At optimum conditions, a dynamic linear range of 5–600?µg L^?1 is obtained, with a limit of detection of 1.2?µg L^?1. The method is used for determination of Co(II) in environmental water and pharmaceutical samples.     

The role of sample preparation in interpretation of trace element concentration variability in moss bioindication studies

Trace element concentrations in plant bioindicators are often determined to assess the quality of the environment. Instrumental methods used for trace element determination require digestion of samples. There are different methods of sample preparation for trace element analysis, and the selection of the best method should be fitted for the purpose of a study. Our hypothesis is that the method of sample preparation is important for interpretation of the results. Here we compare the results of 36 element determinations performed by ICP-MS on ashed and on acid-digested (HNO₃, H₂O₂) samples of two moss species (Hylocomium splendens and Pleurozium schreberi) collected in Alaska and in south-central Poland. We found that dry ashing of the moss samples prior to analysis resulted in considerably lower detection limits of all the elements examined. We also show that this sample preparation technique facilitated the determination of interregional and interspecies differences in the chemistry of trace elements. Compared to the Polish mosses, the Alaskan mosses displayed more positive correlations of the major rock-forming elements with ash content, reflecting those elements’ geogenic origin. Of the two moss species, P. schreberi from both Alaska and Poland was also highlighted by a larger number of positive element pair correlations. The cluster analysis suggests that the more uniform element distribution pattern of the Polish mosses primarily reflects regional air pollution sources. Our study has shown that the method of sample preparation is an important factor in statistical interpretation of the results of trace element determinations.     

Biosorbents for solid-phase extraction of toxic elements in waters

Some trace metals are highly toxic for the environment. There is therefore a need for reliable methods for the determination of metals at trace levels. To this end, new sample pretreatment methods such as separation, preconcentration and speciation prior to the determination of metal ions have developed rapidly. Biosorption has become a major tool for solid-phase extraction methods. This review covers selected biosorbents such as algae, bacteria, filamentous fungi and yeasts, as new sorbents used in the solid-phase extraction of metal ions from various water sample matrices. A survey of the literature over 2004-2014 shows possible applications of selected new sorbents available for use in trace metal analysis in waters using solidphase extraction. We highlight the preconcentration of the toxic elements prior to their determination by atomic spectrometry.     

Solid phase extraction of Cu (II), Ni (II), Co (II), and Fe (III) ions in water samples using salicylaldehyde benzoylhydrazone on Amberlite XAD-4 and their determinations by flame atomic absorption spectrometry

A multi element preconcentration procedure for solid phase extraction on Amberlite XAD-4 as their salicylaldehyde benzoylhydrazone chelates and flame atomic absorption spectrometric determination of some trace metal ions in water samples are proposed in this work. The influences of some analytical parameters, including pH of aqueous solution, amounts of reagent, flow rates of sample and eluent solutions, and sample volume on the quantitative recoveries of copper, nickel, cobalt, and iron were investigated. The effects of concomitant ions on the retentions of the analytes were also examined. The developed method has been successfully applied to the determination of metal ions in some real samples, including, tap water, river water, spring water, and waste water.     

Ligand-less in situ surfactant-based solid phase extraction for preconcentration of silver from natural water samples prior to its determination by atomic absorption spectroscopy

A simple and rapid ligand-less in situ surfactant-based solid phase extraction method for preconcentration of silver from water samples is developed. In this method, a cationic surfactant containing a proper alkyl group (n-dodecyltrimethylammonium bromide) is dissolved in the aqueous sample and then a proper ion-pairing agent (ClO₄^?) is added. Due to the interaction between surfactant and ion-pairing agent, solid particles are formed and used for adsorption of silver carbonate. After centrifugation, the sediment is dissolved in 2.0 mL 1 M HNO₃ in ethanol and then aspirated directly into the flame atomic absorption spectrometer. Variables affecting the extraction efficiencies such as pH, concentrations of surfactant and CO₃^2?, ion pair concentration, and extraction time, are optimized. Under such conditions, the calibration curve is linear from 3 to 700 μg L^?1. Detection limit is 1.1 μg L^?1 with an enrichment factor of 37. The relative standard deviation for eight replicate measurements of 100 μg L^?1 is 2.1%. The method has been applied for the determination of silver in water samples.     

Study on increase in toxicity of Schiff bases on microorganism on chelation with metal

New heterochelates of the type [M(L)(SB)(H₂O)] (where M?=?Mn(II), Co(II), Ni(II), Cu(II), Zn(II), and Cd(II), KHL?=?potassium salt of salicylideneglycine and SB?=?thiophene- O -carboxaldeneaniline) have been synthesized. The heterochelates have been characterized on the basis of elemental analyses, electronic spectra, and magnetic measurement analyses. The structural and geometrical conformation has been discussed on the basis of IR spectral data. A thermal study of the complexes has been carried out to ascertain their thermal stability. Magnetic susceptibility measurements and electronic spectral data suggest a six-coordinated octahedral structure for these complexes. The increase in toxicity of the investigated heterochelate metal compounds was tested against three gram-negative bacteria, S. typhi, E. coli, and Serratia marcescens by the disc diffusion method. It is observed that the heterochelates show higher toxicity when compared to the Schiff bases, metal salts, and control (DMSO) due to chelation. The toxicity is also compared to the standard drug tetracycline.     

A fast and reliable method for quantitative determination of total mercury in vegetables

A cloud-point extraction (CPE) process using the nonionic surfactant, polyethylene glycol tert octylphenyl ether (Triton X-114) was employed for determination of Hg(II) ions in aqueous solutions. The method is based on the ion-pairing reaction of Hg(II) with Pyronin B (PyrB⁺) in the presence of excess iodide at pH 6.0 and extraction of the complex formed. The chemical variables affecting CPE efficiency were studied, and the analytical characteristics of the method were obtained. The calibration curves were linear in the range of 1–40 μg L^?1 with the detection limits of 0.35 and 0.30 μg L^?1 at 556 and 521 nm. Selectivity was also tested. The coefficients of variation of the method are 2.4% and 5.2% for five replicate measurements of mercury at levels of 10 and 25 μg L^?1, respectively. The results obtained for two certified reference samples were in a good agreement with the certified values. The method was applied to the determination of total mercury in vegetable samples.