Adsorption kinetics and isotherms of pesticides onto activated carbon-cloth

Adsorption of pesticides ametryn, aldicarb, dinoseb and diuron from aqueous solution onto high specific area activated carbon-cloth was studied. Kinetics of adsorption was followed by in situ UV-spectroscopy and the data were treated according to various rate models. The extent of adsorption was determined at the end of 125 min adsorption period. Rate constants and the extent of adsorption for the four pesticides were found to follow the order: dinoseb > ametryn > diuron > aldicarb. Adsorption isotherms were derived at 25 °C on the basis of batch analysis. Isotherm data were treated according to Langmuir and Freundlich models. The fits of experimental data to these equations were examined. The types of interactions between the surface and pesticide molecules were discussed.     

Adsorption of pesticides on resins

The objective of this work was to assess the capability of organic hydrophobic polymeric resins Amberlite XAD-4 and XAD-7 to remove the pesticides alachlor and amitrole from water. The pesticides adsorption on the two different adsorbents was measured by batch equilibrium technique and isotherm types and parameters were estimated. Two theoretical models were applied based on a Freundlich and a Langmuir isotherms. The effect of pesticides chemical composition and structure as well as the nature of solid surface on the efficiency of adsorption was evaluated. The influence of pH also was studied. In low pH solutions adsorption of amitrole was higher upon the nonionic aliphatic acrylic ester copolymer XAD-7 in comparison to the nonionic, crosslinked macroreticular copolymer of styrene divinylbenzene XAD-4. In neutral and intermediate pH solutions the polar acrylic ester copolymer XAD-7 was more effective to the retention of alachlor. The acrylic ester copolymer showed at pH 3 the lower effectiveness in alachlor removal from water. The data of the adsorption isotherms of pesticides upon the examined polymeric resins seemed to conform to both the Freundlich and the Langmuir isotherm models.     

Adsorption characteristics of Ni(II) on gamma-type alumina particles and its determination of overall adsorption rate by a differential bed reactor

The adsorption experiment of nickel ion [Ni(II)] on gamma-type alumina by a differential bed reactor in aqueous solutions was investigated to determine the adsorption characteristics and overall adsorption rate. The adsorbed amount increased rapidly with pH from pH 2 to 6 and kept constant over pH 6. The adsorbed amount of Ni(II) increased with temperature from 20 to 50 degrees C. Correlation coefficients (R2) of Langmuir and Freundlich adsorption isotherms were 0.9268 and 0.9489, respectively, and Freundlich isotherm was more suitable for adsorption on gamma-type alumina than Langmuir isotherm.The overall adsorption rate of Ni(II) on gamma-type alumina at pH 6 by a differential bed rector was determined as follows: r = 68.77Ce(1.61) - 17.60qe(0.36). Al(III) ions in solutions were away from the alumina surface during the adsorption of Ni(II) and Al(III) concentration increased with an increasing Ni(II) adsorbed amount on alumina.     

Multi-component sorption isotherms of basic dyes onto peat

The adsorption of basic dyes onto peat from single component and multi-component solution is reported. The adsorption is presented in the form of the equilibrium isotherms. The Freundlich, Langmuir and Redlich-Peterson isotherm equations are fitted to the results and the isotherm constants obtained.     

Determination of the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon using thermogravimetric analysis

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl2 was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl2 were 1.75, 0.688, and 0.230 mg of HgCl2 per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 degrees C for 500 microg/m3 of HgCl2, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer-Emmett-Teller (BET) models were used to simulate the adsorption of HgCl2. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 degrees C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 degrees C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl2 by PAC-derived carbon black favored adsorption at various HgCl2, concentrations and temperatures.     

麻质活性炭的制备及其对Cu2＋的吸附研究

以废麻为原料,KOH为活化剂制备粉状活性炭,通过静态吸附实验研究了活性炭对Cu2＋的吸附性能,探讨了溶液起始pH值、活性炭投加量、吸附时间、起始Cu2＋质量浓度等对Cu2＋吸附效果的影响。结果表明,溶液pH和活性炭投加量对吸附效果有较大影响,活性炭对Cu2＋的吸附率在60 min内超过50%,初始浓度在10~50 mg/L时,活性炭对Cu2＋的吸附量与起始浓度近似成正比。采用Langmuir、Freundlich吸附等温式对吸附平衡数据进行了拟合,结果表明吸附等温线符合Frenudlich模型。采用傅立叶红外光谱法（FT-IR）分析了活性炭的表面官能团,分析表明活性炭表面酸性官能团可能是吸附Cu2＋的活性中心。     

粉末活性炭对水中农药的吸附性能研究

研究了粉末活性炭对2,4-滴、呋喃丹、甲萘威和莠去津的吸附过程和吸附规律以及投炭量和水质对粉末活性炭吸附性能的影响。结果表明,粉末活性炭能有效去除4种农药;吸附规律符合Freundlich吸附等温线和Langmuir吸附等温线;吸附时间为30 min时,去离子水中的去除率已达到80%以上;随着投炭量的增加,去除率提高,粉末活性炭的吸附容量降低;在不同水质条件下,粉末活性炭的吸附等温线可能不同,因此在应急处理中,首先应该确定该水质下的吸附等温线,然后求出投炭量。     

Adsorption of glyphosate on resin supported by hydrated iron oxide: equilibrium and kinetic studies

Hydrated iron oxide supported on resin (D301) was prepared as a new sorbent for the removal of glyphosate from wastewater. Batch adsorption studies were performed on glyphosate aqueous solutions with different initial glyphosate concentrations and temperatures. Experimental data were analyzed using the Langmuir and Freundlich isotherms, and the adsorption data were best fit to the Langmuir isotherm model. The thermodynamic parameters AG, AH, and AS also were calculated for the adsorption processes. Adsorption rate constants were determined using the pseudo-first-order and pseudo-second-order rate equations and Kannan-Sundaram intraparticle diffusion models. Adsorption of glyphosate clearly followed the pseudo-second-order model and was controlled by both film diffusion and intraparticle diffusion.     

粉煤灰砖块对磷酸盐的吸附特性

以建筑废料粉煤灰砖块为吸附剂材料,通过静态吸附实验研究其对磷酸盐的吸附特征,以及磷酸盐初始浓度、吸附剂投加量、pH等因素对吸附反应的影响。Langmuir、Freundlich和Temkin等温模型的分析发现,Langmuir等温式方程最适合描述吸附过程,对磷酸盐的理论饱和吸附容量为44.62 mg/g。利用伪一级动力学模型、伪二级动力学模型和颗粒内扩散模型考察了吸附过程特征,其中伪二级动力学模型为最适于描述粉煤灰砖块对磷酸盐的吸附过程的动力学模型。通过颗粒内扩散模型、Bangham方程及Boyd模型对吸附动力学机理进行的探讨表明,颗粒内扩散速率不是粉煤灰砖块吸附磷酸盐反应的惟一速率控制步,膜扩散速率和颗粒内扩散速率共同影响着吸附反应速率。磷酸盐浓度较低时主要是膜扩散限制吸附反应速率,而磷酸盐浓度较高时则颗粒内扩散成为速率控制步。研究证明,粉煤灰砖块粉末作为湿地基质具有对磷酸盐很强的吸附能力,在减少了固体废弃物的数量的同时又可以实现水污染控制的目的。     

Kinetics and isotherm modeling of azoxystrobin and imidacloprid retention in biomixtures

The paper reports the kinetics and adsorption isotherm modeling for imidacloprid (IMIDA) and azoxystrobin (AZOXY) in rice straw (RS)/corn cob (CC) and peat (P)/compost (C) based biomixtures. The pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich and intraparticle diffusion models were used to describe the kinetics. The adsorption data were subjected to the Langmuir and the Freundlich isotherms. Results (r²_Adj values) suggested that the modified Elovich model was the best suited to explain the kinetics of IMIDA sorption while different models explained AZOXY sorption kinetics in different biomixtures (PFO in RS?+?C and RS?+?P; PSO in CC?+?P and Elovich in CC?+?C). Biomixtures varied in their capacity to adsorb both pesticides and the adsorption coefficient (K_d) values were 116.8–369.24 (AZOXY) and 24.2–293.4 (IMIDA). The Freundlich isotherm better explained the sorption of both pesticides. Comparison analysis of linear and nonlinear method for estimating the Freundlich adsorption constants was made. In general, r²_Adj values were higher for the nonlinear fit (AZOXY?=?0.938–0.982; IMIDA?=?0.91–0.970) than the linear fit (AZOXY?=?0.886–0.993; IMIDA?=?0.870–0.974) suggesting that the nonlinear Freundlich equation better explained the sorption. The rice straw-based biomixtures performed better in adsorbing both the pesticides and can be used in bio-purification systems.     

Determination of the Adsorption Isotherm of Vapor-Phase Mercury Chloride on Powdered Activated Carbon Using Thermogravimetric Analysis

Abstract

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl₂ was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl₂ were 1.75, 0.688, and 0.230 mg of HgCl₂ per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 °C for 500 µg/m³ of HgCl₂, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer–Emmett–Teller (BET) models were used to simulate the adsorption of HgCl₂. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 °C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 °C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl₂ by PAC-derived carbon black favored adsorption at various HgCl₂ concentrations and temperatures.     

腐熟污泥对废水中Cd(Ⅱ)与Zn(Ⅱ)的吸附性能研究

利用腐熟污泥作为一种重金属吸附剂,考察其对水中重金属锌和镉的吸附过程.实验数据的拟合采用了Pseudo-first Order-和Pseudo-second Order 2种动力学模型以及Langmuir和Freundlich 2种吸附等温线模型;拟合结果表明,腐熟污泥对锌与镉的吸附过程符合Pseudo-second ...     

Removal of MCPA from aqueous solutions by acid-activated spent bleaching earth

The removal of MCPA (4-chloro-2-methyl phenoxyacetic acid) from aqueous solutions by activated spent bleaching earth (SBE) was studied as a function of time, initial concentration, adsorbent concentration, and temperature. The Langmuir and Freundlich isotherms were fitted by the adsorption data obtained. The values of Langmuir and Freundlich constants were determined. The adsorption kinetics was described by the Lagergren equation. Mass transfer coefficient and thermodynamic parameters were also calculated. Column experiments were conducted and brekthrough capacities were found for different concentrations and different flow rates. The study demonstrates that acid-treated SBE could be used as an efficient adsorbent for the removal of MCPA-bearing wastewater effluents.     

Adsorption of acid dye onto activated carbons prepared from agricultural waste bagasse by ZnCl2 activation

A series of activated carbons were prepared from agricultural waste sugarcane bagasse by chemical activation with zinc chloride (ZnCl2) as an activating agent at 500 degrees C and 0.5 h soaking time. The Langmuir surface area and total pore volume were used to estimate the average pore diameter of the carbon products. The values of the surface area and pore volume increased linearly with increase in the impregnation ratio (IR) up to 100 wt%. The adsorption capacities of the derived adsorbents for Acid Orange 10 were measured at 20 degrees C and 40 degrees C to gain further insights into the acidic surface oxides of the adsorbent from the results of Fourier transform infrared (FTIR) spectroscopy analysis and pH measurement. Adsorption isotherms of the acid dye on adsorbents prepared were determined and correlated with common isotherm equations. It was found that the Langmuir model appears to fit the isotherm data better than the Freundlich model. The physical properties of these adsorbents were consistent with the parameters obtained from the isotherm equations.     

Modification of Langmuir isotherm in solution systems--definition and utilization of concentration dependent factor

The Langmuir isotherm, originally derived for the adsorption of gas molecules on solid surfaces, was modified to fit the adsorption isotherm of solutes onto solid surfaces in solution systems. The aim of this modification is based on the fact that direct application of the Langmuir isotherm to solution systems often leads to poor data fitting. In the present communication, it is shown that the level of data fitting to the Langmuir isotherm of literature data can be improved by a simple modification introducing a concentration dependent factor, X. The key concept of the modification lies in that the concentration of solute affects both adsorption and desorption stages. As a first approximation, we adopted a single-term polynomial for both processes of adsorption and desorption. Based on reanalysis of literature data of adsorption in solution, we confirmed that indeed the modified Langmuir isotherm more accurately describes the experimental observations. Furthermore, we proposed that the concentration dependent factor could be associated with the surface heterogeneity index that was introduced in a few other modified Langmuir isotherms. Some advantages and limitations of proposed modified Langmuir isotherm are also discussed.     

Adsorption of 2,4-dichlorophenoxyacetic acid and 4-chloro-2-metylphenoxyacetic acid onto activated carbons derived from various lignocellulosic materials

Adsorption of 2,4-dichlorophenoxyacetic acid (2,4-D) and 4-chloro-2-metylphenoxyacetic acid (MCPA) from aqueous solution onto activated carbons derived from various lignocellulosic materials including willow, miscanthus, flax, and hemp shives was investigated. The adsorption kinetic data were analyzed using two kinetic models: the pseudo-first order and pseudo-second order equations. The adsorption kinetics of both herbicides was better represented by the pseudo-second order model. The adsorption isotherms of 2,4-D and MCPA on the activated carbons were analyzed using the Freundlich and Langmuir isotherm models. The equilibrium data followed the Langmuir isotherm. The effect of pH on the adsorption was also studied. The results showed that the activated carbons prepared from the lignocellulosic materials are efficient adsorbents for the removal of 2,4-D and MCPA from aqueous solutions.     

Adsorption of propisochlor on soils and soil components equation for multi-step isotherms

Static equilibrium measurements were performed for the study of propisochlor on three different kinds of soils at pH = 7.0 at 25 degrees C. The concentration of herbicide was changed from 30 to 300 mumol/l. The obtained two-step adsorption isotherms cannot be evaluated by using the Freundlich or Langmuir equations. New equation has been derived by making use of the usual mass balance and equilibrium relationships of the adsorption and by considering the possibility of the formation of associates of the hydrophobic solute molecules. The characteristic model parameters of each step of the adsorption isotherm were estimated for the studied systems by a non-linear least square regression. The calculated curves fit well to the experimentally obtained two-step isotherms and the parameters of the model can be used for the characterization of the pesticide-soil interactions and consequently the mobility of the propisochlor in soil/water systems.     

改性玉米秸秆吸附Cu^2＋的动力学和热力学

本研究用ZnCl2作为活化剂，使用功率640W的微波照射4min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响，并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明：投加量为0．2g，pH为6，改性玉米秸秆对Cu^2＋具有很好的吸附效果，吸附在8h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程，其反应的吉布斯自由能△G〈0，为自发反应过程。     

Adsorptive removal of an acid dye by lignocellulosic waste biomass activated carbon: equilibrium and kinetic studies

Chemically prepared activated carbon material derived from palm flower was used as adsorbent for removal of Amido Black dye in aqueous solution. Batch adsorption studies were performed for the removal of Amido Black 10B (AB10B), a di-azo acid dye from aqueous solutions by varying the parameters like initial solution pH, adsorbent dosage, initial dye concentration and temperature with three different particle sizes such as 100 μm, 600 μm and 1000 μm. The zero point charge was pH 2.5 and the maximum adsorption occurred at the pH 2.3. Experimental data were analyzed by model equations such as Langmuir, Freundlich and Temkin isotherms and it was found that the Freundlich isotherm model best fitted the adsorption data and the Freundlich constants varied from (K_F) 1.214, 1.077 and 0.884 for the three mesh sizes. Thermodynamic parameters such as ΔG, ΔH and ΔS were also calculated for the adsorption processes and found that the adsorption process is feasible and it was the endothermic reaction. Adsorption kinetics was determined using pseudo first-order, pseudo second-order rate equations and also Elovich model and intraparticle diffusion models. The results clearly showed that the adsorption of AB10B onto lignocellulosic waste biomass from palm flower (LCBPF) followed pseudo second-order model, and the pseudo second-order rate constants varied from 0.059 to 0.006 (g mg⁻¹ min) by varying initial adsorbate concentration from 25 mg L⁻¹ to 100 mg L⁻¹. Analysis of the adsorption data confirmed that the adsorption process not only followed intraparticle diffusion but also by the film diffusion mechanism.     

In vitro study of oxytetracycline adsorption on activated charcoal

In vitro adsorption experiments simulating pH in gastric environment and using Langmuir isotherm, showed that 408 mg of oxytetracycline was adsorbed per gram of activated charcoal. Langmuir isotherm fitted adsorption data better than a Freundlich isotherm. Freundlich isotherm showed a specific adsorption capacity of 518 mg/g for activated charcoal. Both isotherm parameters indicated a strong oxytetracycline adsorption on activated charcoal in terms of quantity and binding strength. The results demonstrate that the concomitant use of oxytetracyline and activated charcoal should be avoided.