Latent hydraulic reactivity of blended cement incorporating slag made from municipal solid waste incinerator fly ash

The reactivity of cement pastes made by blending Portland cement with slag from municipal solid waste incinerator (MSWI) fly ash was investigated to assess the potential of recycling MSWI fly ash slag. The slag, prepared by melting MSWI fly ash at 1400 degrees C for 30 min, was pulverized and ground, then blended with ordinary Portland cement (OPC), using various substitution levels to make slag-blended cement (SBC). The pozzolanic reactivity of the ecocement was then characterized by determining variations in the compressive strength, degree of hydration, microstructure, speciation, and mineralogical crystalline phases. The results suggest that the strength of the pastes at an early age decreased with increasing substitution levels, whereas the strength at a later age of the tested pastes (with substitution levels less than 10%) outperformed OPC paste because of typical SBC properties. The development of strength at a later age was also confirmed by X-ray diffraction and scanning electron microscopy techniques. This implies that active silica (Si) and alumina (Al) react with the hydration product, calcium hydroxide (Ca(OH)2), to form calcium silicate hydrate (C-S-H), which contributed to strength development at a later age by the filling up of pores in the SBC pastes. The pozzolanic activity of the SBC pastes indicates that it is suitable for use as a substitute for OPC in blended cement.     

Latent Hydraulic Reactivity of Blended Cement Incorporating Slag Made from Municipal Solid Waste Incinerator Fly Ash

Abstract

The reactivity of cement pastes made by blending Portland cement with slag from municipal solid waste incinerator (MSWI) fly ash was investigated to assess the potential of recycling MSWI fly ash slag. The slag, prepared by melting MSWI fly ash at 1400 °C for 30 min, was pulverized and ground, then blended with ordinary Portland cement (OPC), using various substitution levels to make slag-blended cement (SBC). The pozzolanic reactivity of the ecocement was then characterized by determining variations in the compressive strength, degree of hydration, microstructure, speciation, and mineralogical crystalline phases. The results suggest that the strength of the pastes at an early age decreased with increasing substitution levels, whereas the strength at a later age of the tested pastes (with substitution levels less than 10%) outperformed OPC paste because of typical SBC properties. The development of strength at a later age was also confirmed by X-ray diffraction and scanning electron microscopy techniques. This implies that active silica (Si) and alumina (Al) react with the hydration product, calcium hydroxide (Ca(OH)₂), to form calcium silicate hydrate (C-S-H), which contributed to strength development at a later age by the filling up of pores in the SBC pastes. The pozzolanic activity of the SBC pastes indicates that it is suitable for use as a substitute for OPC in blended cement.     

Hydration properties of eco-cement pastes from waste sludge ash clinkers

Three types of hydraulic cements have been developed by incorporating sludge ash from a primary sewage treatment plant and a water purification plant, as well as slag from steelworks (ferrate), as a partial replacement for clay, silica, alumina, and iron oxide in raw cement meal. The raw meal for the pre-determined recipes was prepared by heating it to 1400 degrees C for 6 hr in a clinkerization process, using a simulated incinerator and smelter. The major components of ordinary Portland cement, C3S, C2S, C3A, and C4AF, were all found in the clinkers. Of the three types of eco-cements, the eco-cement A paste was most similar to ordinary Portland cement in terms of composition and compressive strength development, while the eco-cement B paste showed early strength development. The differential thermal analysis species analyses indicated that the hydrates in the eco-cement pastes were mainly calcium hydroxide and CSH gels, like those found in ordinary Portland cement paste. Moreover, the degree of hydration, as determined by nuclear magnetic resonance, increased in all eco-cement pastes with an increasing curing age. The results indicate that it indeed is feasible to use sludge ash and ferrate to replace up to 20% of the mineral components of raw materials for cement.     

Hydration Properties of Eco-Cement Pastes from Waste Sludge Ash Clinkers

Abstract

Three types of hydraulic cements have been developed by incorporating sludge ash from a primary sewage treatment plant and a water purification plant, as well as slag from steelworks (ferrate), as a partial replacement for clay, silica, alumina, and iron oxide in raw cement meal. The raw meal for the pre-determined recipes was prepared by heating it to 1400 °C for 6 hr in a clinkerization process, using a simulated incinerator and smelter. The major components of ordinary Portland cement, C₃S, C₂S, C₃A, and C₄AF, were all found in the clinkers. Of the three types of eco-cements, the eco-cement A paste was most similar to ordinary Portland cement in terms of composition and compressive strength development, while the eco-cement B paste showed early strength development. The differential thermal analysis species analyses indicated that the hydrates in the eco-cement pastes were mainly calcium hydroxide and CSH gels, like those found in ordinary Portland cement paste. Moreover, the degree of hydration, as determined by nuclear magnetic resonance, increased in all eco-cement pastes with an increasing curing age. The results indicate that it indeed is feasible to use sludge ash and ferrate to replace up to 20% of the mineral components of raw materials for cement.     

污泥焚烧灰固化处理技术研究

研究了硅酸盐水泥、高铝水泥、高岭土和β-萘系减水剂在污泥焚烧灰固化技术中的应用效果。考察了污泥焚烧灰固化块(以下简称固化块)的抗压强度,测定了固化块的重金属浸出毒性,并采用X射线衍射(XRD)和扫描电镜(SEM)分析固化块组成和微观结构。结果表明,4种物质对提高固化块的抗压强度均具有较好的效果,硅酸盐水泥、高铝水泥、高岭土和β-萘系减水剂的适宜掺量分别为10、30、20、1.0g(以100g污泥焚烧灰中掺加的质量计)。XRD和SEM分析结果显示,经固化处理后制得的固化块结构密实,存在石英(SiO2)、水化硅铝酸钙(CaAl2Si2O8)和水化硅酸铝钙(Ca2Al2SiO7)等物质,其中水化硅铝酸钙等凝胶物质有利于提高固化块的抗压强度。     

One-part alkali-activated slag binder for cemented fine tailings backfill: proportion optimization and properties evaluation

In this study, a one-part alkali-activated slag (AAS) composed of ground-granulated blast furnace slag, desulfurized gypsum, and hydrated lime is proposed as alternative to cement for the production of cemented fine tailings backfill (CFTB), which is an environmentally friendly binder consisting of 93.72 wt.% industrial solid waste. Results show that AAS with 67.83 wt.% slag, 25.92 wt.% desulfurized gypsum, and 6.25 wt.% hydrated lime yields the highest strength, which is 1.7–3.2 times that of ordinary Portland cement (OPC). Aside from calcium silicate hydrate gel, appreciable quantity of ettringite characterized by interlocking needles structure and high bound water is also produced during the AAS hydration process. In addition, the hydration heat of the AAS binder is 48% less than that of OPC. Moreover, CFTB made of AAS provides better workability than that of CFTB with OPC up to 20 h. The findings of this study will contribute to the production of more cost-effective, durable, and environmental-friendly cemented fine tailings backfill.

     

Fly and bottom ashes from biomass combustion as cement replacing components in mortars production: Rheological behaviour of the pastes and materials compression strength

In the present research mortar pastes obtained by replacing a commercial cement with the equivalent mass of 5, 10, 20 and 30 wt.% of fly ash or bottom ash from fir chips combustion, were prepared and rheologically characterized. It was observed that the presence of ash modifies their rheological behaviour with respect to the reference blend due to the presence, in the ashes, of KCl and K₂SO₄ which cause precipitation of gypsum and portlandite during the first hydration stages of the pastes. Hydrated materials containing 5 wt.% of ash display compression strength and absorption at 28 d of same magnitude as the reference composition; conversely, progressive increase of ash cause a continuous decline of materials performances. Conversely, samples tested after 180 d display a marked decline of compression strength, as a consequence of potassium elution and consequent alkali-silica reaction against materials under curing.     

地聚合材料固化处理垃圾焚烧飞灰

以垃圾焚烧飞灰和高岭土为主要原料,氢氧化钾为碱激活剂制备了地聚合材料,当焚烧飞灰的掺加量在70%时,其28 d抗压强度可达19.36 MPa。重金属浸出实验表明,地聚合物材料对垃圾焚烧飞灰中的重金属有明显的固化效果,在28 d时基本无溶出。SEM结果表明,地聚合材料的断面结构与力学性能和固化效果相关,XRD和FTIR的分析结果表明,焚烧飞灰和高岭土在碱的激发下生成新的硅铝酸盐聚合物,所得地聚合材料为无定形态。     

垃圾焚烧飞灰浸出特性及固化试验的研究

垃圾焚烧飞灰残留有重金属元素和二恶英等物质而被认为是危险废物,必须对之进行稳定化处理.通过试验研究分析了国内首家自主开发成功的广东省东莞市某回转窑垃圾焚烧发电厂垃圾焚烧飞灰的化学成分及矿物组成,研究了飞灰的浸出毒性,考察了水泥固化焚烧飞灰的效果,并与熔融/玻璃固化进行了比较.研究表明,该焚烧飞灰中重金属Cd的浸出毒性严重超标,并且随pH值的减小而增大,水泥固化效果随龄期的增大而更加显著.熔融/玻璃固化的效果优于水泥固化,但其经济性有待提高.     

垃圾焚烧飞灰综合利用研究进展

焚烧处理是解决日益增长生活垃圾的有效方法。垃圾焚烧产生的飞灰因含有大量的重金属等污染物而属危险废物 ,目前常采用的处理方法是填埋。本文就垃圾飞灰的综合利用研究现状进行了论述。从环境和技术的角度看 ,垃圾飞灰的预处理、水泥固化和玻璃化是目前飞灰综合利用的主要研究方向     

Cytotoxicity of municipal solid waste incinerator ash wastes toward mammalian kidney cell lines

In this study, three municipal solid waste incinerator (MSWI) ash wastes-bottom ash, scrubber residue, and baghouse ash-were extracted using a toxicity characteristic leaching procedure (TCLP) extractant. These so-called final TCLP extracts were applied to African green monkey kidney cells (Vero), baby hamster kidney cells (BHK-21), and pig kidney cells (PK-15), multi-well absorption reader analysis was performed to test how the cytotoxicity of the incineration ashes would affect the digestive systems of animals. Ion-coupled plasma analyses indicated that the baghouse ash extract possessed the highest pH and heavy metal concentration, its cytotoxicity was also the highest. In contrast, the bottom ash and the scrubber residue exhibited very low cytotoxicities. The cytotoxicities of mixtures of baghouse ash and scrubber residue toward the three tested cell lines increased as the relative ratio of the baghouse ash increased, especially for the Vero cells. The slight cytotoxicity of the scrubber residue arose mainly from the presence of Cr species, whereas the high cytotoxicity of the baghouse ash resulted from its high content of heavy metals and alkali ions. In addition, it appears that the dissolved total organic carbon content of these ash wastes can reduce the cytotoxicity of ash wastes that collect in animal cells.     

Influence of thermally activated paper sludge on the behaviour of blended cements subjected to saline and non-saline environments

Background, aim and scope  One of the problems to affect Portland cement matrices is low resistance to aggressive agents, due principally to the presence of a high content of portlandite in the hydrated cements. Pozzolanic materials have played an important role in the improving the durability of cement-based materials for decades. This work studies the behaviour of cement mortar matrices blended with 10% calcined paper sludge (source for metakaolinite) and exposed to different environmental conditions (saline and non-saline environments) after 6 and 12 months of exposure. Materials and methods  Two cements were studied: an ordinary Portland cement (CEM 1, 42.5R), acting as reference cement, and a blended cement formulated by mixing 90% (by mass) of CEM 1, 42.5R with 10% (by mass) of paper sludge calcined at 700°C for 2 h. The specimens were exposed 1 year to saline and non-saline environments. All the mineralogy samples were studied through X-ray diffraction and scanning electron microscopy (SEM) equipped with an energy dispersive X-ray analyser. The in-depth study on ionic mobility was performed on samples subjected to natural exposure (coast and tableland) for 6 and 12 months. Results  Portland cement was composed of quartz, calcite, calcium hydroxide and tobermorite gels. The pozzolanic cement (10% calcined paper sludge) is of the same composition but a high calcite concentration and barium carbonate. SEM analysis from coastline show deposits of variable composition. The deposits are identified on the surface of different mineral components. The minerals from tableland are much fractured, i.e. calcite and feldspars. Inside the fractures, the deposits and the ions are located and trapped superficially. Discussion  SEM analysis of control cement Portland and 10% calcined paper sludge shows deposits on quartz and calcite with a very high concentration of Pb, Zn, Cl and barium sulphate. A very porous aspect is due to the presence of the different aggregate types. This porous configuration permits retention of the ion environment. The pozzolanic cement in environments subject to the saline mist favours the retention and transport of ions observed. Something similar also happens with the increase in exposure to outdoor weather. Non-saline samples show temperature changes (ice or thaw cycles). Barium retention is kept on the surface in fracture lines by the gelification processes. In general, it may be inferred that an increase in exposure time increases the diffusion of ions towards test piece interiors. The chemical composition profiles show that the ions present different penetration speeds. Conclusions  The results indicate the better vulnerability of pozzolanic cements from calcined paper sludge in saline and non-saline environments. The cements with a 10% addition of calcined paper sludge favour retention and transport of ion has been observed. Recommendations and perspectives  Today, projects are centred on a new recycling line for industrial waste of this kind, with special attention on its incorporation in cement manufacture as a pozzolanic material, setting the most appropriate activation conditions of the mineralogical compound in this waste (kaolinite and metakaolinite) and taking them as a starting point for this project. The use of pozzolanic cement with 10% addition of calcined paper sludge is a system which favours ionic retention.     

锡冶炼含砷烟尘低温陶瓷固化技术

以锡冶炼过程中排放的含砷烟尘为研究对象,对浸出特性和低温陶瓷胶凝材料对其的固化效果进行了研究。结果表明,含砷烟尘As、Cu和Zn毒性浸出浓度分别为6 783、167和224 mg/L,严重超过国家毒性浸出鉴别标准值。其经低温陶瓷胶凝材料固化处理,当含砷烟尘掺量小于40%,自然养护3 d,As、Cu和Zn毒性浸出浓度急剧降低,且低于国家标准值。XRD和SEM分析表明,低温陶瓷胶凝材料在复合化学激发剂作用下,反应生成类沸石水化铝硅酸盐矿物(Al-O-Si);固化体中Ca-Fe-As-O盐是As固化的主要矿物相。Cu2+、Zn2+替换铝硅酸盐聚合物结构中的Na+、K+保持平衡电荷。胶凝材料水化产物填充于材料颗粒间,使其连接成一致密整体,有效降低了有害物质的毒性浸出浓度。     

高铝粉煤灰提取氧化铝后硅钙渣用作水泥混合材

为了使高铝粉煤灰提取氧化铝后所产生的硅钙渣被大量的用作水泥混合材,通过水泥强度、水化放热和干缩性实验研究了原状硅钙渣和脱碱硅钙渣对水泥强度和稳定性的影响。结果表明,当硅钙渣掺量达30%时,硅钙渣水泥强度仍可满足P·C 32.5水泥要求。且随硅钙渣掺入量的增加,水泥早期水化放热速率增加的同时水泥累计水化放热量和干缩率还会显著降低。与原状硅钙渣相比,在同等掺量的情况下,脱碱硅钙渣更有利于保持水泥强度,降低其水化热和改善干缩性。     

Immobilization of antimony waste slag by applying geopolymerization and stabilization/solidification technologies

During the processing of antimony ore by pyrometallurgical methods, a considerable amount of slag is formed. This antimony waste slag is listed by the European Union as absolutely hazardous waste with a European Waste Catalogue code of 10 08 08. Since the levels of antimony and arsenic in the leachate of the antimony waste slag are generally higher than the landfilling limits, it is necessary to treat the slag before landfilling. In this study, stabilization/solidification and geopolymerization technologies were both applied in order to limit the leaching potential of antimony and arsenic. Different combinations of pastes by using Portland cement, fly ash, clay, gypsum, and blast furnace slag were prepared as stabilization/solidification or geopolymer matrixes. Sodium silicate–sodium hydroxide solution and sodium hydroxide solution at 8 M were used as activators for geopolymer samples. Efficiencies of the combinations were evaluated in terms of leaching and unconfined compressive strength. None of the geopolymer samples prepared with the activators yielded arsenic and antimony leaching below the regulatory limit at the same time, although they yielded high unconfined compressive strength levels. On the other hand, the stabilization/solidification samples prepared by using water showed low leaching results meeting the landfilling criteria. Use of gypsum as an additive was found to be successful in immobilizing the arsenic and antimony.

ImplicationsDespite the wide use of antimony for industrial purposes, disposal options for an antimony waste such as slag from thermal processing of antimony ore were not reported in the existing literature. This study aimed to develop a disposal strategy for the hazardous antimony waste slag. The findings of this study would contribute to understand the immobilization mechanisms of antimony and arsenic and will also be of interest to the owners of the antimony ore processing plants and to researchers investigating the efficiency of stabilization/solidification and geopolymerization technologies.     

添加垃圾焚烧飞灰冷固小球的工业烧结实验

将垃圾焚烧飞灰添加进烧结冷固球团配料进行造球,对冷固小球的成分及强度进行分析,结果表明,添加垃圾焚烧飞灰冷固小球化学组成稳定,重金属浸出毒性远低于危险废物鉴别标准,落下强度较基准期略微降低,但符合运输、贮存的要求.并对添加了飞灰的冷固小球对其后续烧结、冶炼工序的影响进行分析,结果表明,用添加飞灰的冷固小球进行烧结所得烧结矿的转鼓强度、落下强度及常规化学成分较基准期没有太大变化,添加飞灰进行造球、烧结,对其后续冶炼工序的顺行几乎没有影响,所带来的额外的环境污染微乎其微.     

Strength development of solidified/stabilized organic waste and optimum treatment design

Artificially contaminated (spiked) natural soils were solidified/stabilized using various combinations of commonly used additives, such as lime, cement, fly ash, activated carbon, and silica fume. The effectiveness of the solidification/stabilization (S/S) processes was evaluated based on experimental findings from compaction testing, unconfined compressive shear strength, and X-ray diffraction (XRD). Correlations of limited reliability between unconfined compressive strength and penetrometer and torvane measurements were derived. Results from XRD experiments indicated that certain organic contaminants (i.e., naphthalene and pyrene) might impact the S/S processes for a given combination of additives. The type and amount of organic contaminants also affected the pozzolanic reactions. Specifically, the absence or small peak intensity of pozzolanic product XRD patterns for a given combination of additives was a good indication that the type and the amount of organic contaminant present inhibited pozzolanic reactions. This phenomenon was tested and confirmed for actual field-contaminated samples.     

水泥对垃圾焚烧飞灰的固化处理试验研究

对垃圾焚烧飞灰的化学成分、重金属物质的含量及浸出浓度进行测试分析.结果表明,飞灰中Pb和Cr等重金属物质浸出量超过浸出毒性标准,因而被认为是危险废物,必须进行固化处理.还考察了水泥对焚烧飞灰中重金属物质固化的效果,研究表明当飞灰掺量适当时,重金属物质的固化效果良好.重金属物质通过物理固封、替代,沉淀反应和吸附等形式可固化进水泥水化产物结构中.     

Strength Development of Solidified/Stabilized Organic Waste and Optimum Treatment Design

Abstract

Artificially contaminated (spiked) natural soils were solidified/stabilized using various combinations of commonly used additives, such as lime, cement, fly ash, activated carbon, and silica fume. The effectiveness of the solidification/stabilization (S/S) processes was evaluated based on experimental findings from compaction testing, unconfined compressive shear strength, and X-ray diffraction (XRD). Correlations of limited reliability between unconfined compressive strength and penetrometer and torvane measurements were derived. Results from XRD experiments indicated that certain organic contaminants (i.e., naphthalene and pyrene) might impact the S/S processes for a given combination of additives. The type and amount of organic contaminants also affected the pozzolanic reactions. Specifically, the absence or small peak intensity of pozzolanic product XRD patterns for a given combination of additives was a good indication that the type and the amount of organic contaminant present inhibited pozzolanic reactions. This phenomenon was tested and confirmed for actual field-contaminated samples.     

Binary blended fly ash concrete with improved chemical resistance in natural and industrial environments

Environmental Science and Pollution Research - This study reports the enhanced chemical resistance of a blended concrete mix (CFNI) made with 40 wt.% fly ash, 2 wt.% nanoparticles, and 2 wt.%...