Octyl and nonylphenol ethoxylates and carboxylates in wastewater and sediments by liquid chromatography/tandem mass spectrometry

This work presents an LC–MS–MS-based method for the quantitation of nonylphenol ethoxylates (NPEOs) and octylphenol ethoxylates (OPEOs) in water, sediment, and suspended particulate matter, and three of their carboxylated derivatives in water. The alkylphenol ethoxylates (APEOs) were analyzed using isotope dilution mass spectrometry with [¹³C₆]-labeled analogues, whereas the carboxylated derivatives were determined by external standard quantitation followed by confirmation using standard additions. The method was used to study APEO’s behavior in a wastewater treatment plant (WWTP), where total dissolved NP0-16EO concentration was reduced by approximately 99% from influent (390 μg l⁻¹) to final effluent (4 μg l⁻¹), and total OP0-5EO concentration decreased by 94% from 3.1 to 0.2 μg l⁻¹. In contrast, the carboxylated derivatives were formed during the process with NP0-1EC concentrations increasing from 1.4 to 24 μg l⁻¹. Short-chain APEOs were present in higher proportions in particulate matter, presumably due to greater affinity for solids compared to the long-chain homologues. NP (0.49 μg l⁻¹) and NP0-1EC (4.8 μg l⁻¹) were the only APEO-related compounds detected in a surface water sample from a WWTP-impacted estuary; implying that 90% of the mass was in the form of carboxylated derivatives. Sediment analysis showed nonylphenol to be the single most abundant compound in sediments from the Baltimore Harbor area, where differences in homologue distribution suggested the presence of treated effluent in some of the sites and non-treated sources in the rest.     

Isoprene emission from tropical trees in Okinawa Island, Japan

This study surveyed isoprene emission from 42 indigenous and exotic tropical trees in subtropic Okinawa, Japan. Of the 42 trees studied, 4 emitted isoprene at a rate in excess of 20 μg g⁻¹ h⁻¹, and 28 showed the rates of 1–10 μg g⁻¹ h⁻¹. The remainder emitted less than 1 μg g⁻¹ h⁻¹. The majority of trees in this study may therefore fall within the lower emitting species. However, species in Moraceae that is indigenous in Okinawa emitted isoprene at relatively higher rates with an average of 14.2 μg g⁻¹ h⁻¹. The highest emission rate of 107.1 μg g⁻¹ h⁻¹ for Ficus virgata yielded the area basis rate of 47.4 nmol m⁻² s⁻¹, which is almost equivalent to the rate of high emitting species. Furthermore, a linear relationship between light intensity and isoprene emission was noted with Ficus virgata up to 1700 μmol m⁻² s⁻¹. These findings may show the potential importance of subtropical areas as sources of isoprene to the atmosphere.     

Arsenic removal from water employing heterogeneous photocatalysis with TiO2 immobilized in PET bottles

Arsenic oxidation (As(III) to As(V)) and As(V) removal from water were assessed by using TiO₂ immobilized in PET (polyethylene terephthalate) bottles in the presence of natural sunlight and iron salts. The effect of many parameters was sequentially studied: TiO₂ concentration of the coating solution, Fe(II) concentration, pH, solar irradiation time; dissolved organic carbon concentration. The final conditions (TiO₂ concentration of the coating solution: 10%; Fe(II): 7.0 mg l⁻¹; solar exposure time: 120 min) were applied to natural water samples spiked with 500 μg l⁻¹ As(III) in order to verify the influence of natural water matrix. After treatment, As(III) and total As concentrations were lower than the limit of quantitation (2 μg l⁻¹) of the voltammetric method used, showing a removal over 99%, and giving evidence that As(III) was effectively oxidized to As(V). The results obtained demonstrated that TiO₂ can be easily immobilized on a PET surface in order to perform As(III) oxidation in water and that this TiO₂ immobilization, combined with coprecipitation of arsenic on Fe(III) hydroxides(oxides) could be an efficient way for inorganic arsenic removal from groundwaters.     

Accumulation, speciation and cellular localization of copper in Sesbania drummondii

Growth, accumulation and intracellular speciation and distribution of copper (Cu) in Sesbania drummondii was studied using scanning-electron microscopy (SEM), X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS). The growth of seedlings was assessed in terms of biomass accumulation. The growth of the seedling was enhanced by 73.5% at a low Cu concentration (50 mg l⁻¹) compared to the control treatment. Additionally, seedling growth was inhibited by 18% at 300 mg l⁻¹ Cu with respect to the control. Copper concentration in roots and shoots was increased with increasing Cu concentration in the growth solution. The accumulation of Cu was found to be higher in roots than in the shoots. At a concentration of 300 mg l⁻¹ Cu, the roots accumulated 27,440 mg Cu kg⁻¹ dry weight (dw) while shoots accumulated 1282 mg Cu kg⁻¹ dw. Seedlings were assessed for photosynthetic activity by measuring chlorophyll a fluorescence parameters: F_v/F_m and F_v/F₀ values. Photosynthetic integrity was not affected by any of the Cu treatments. The X-ray absorption spectroscopic (XAS) studies showed that Cu was predominantly present as Cu(II) in Sesbania tissue. In addition, from the XAS studies it was shown that the Cu exists in a mixture of different coordination states consisting of Cu bound to sugars and small organic acids with some possible precipitated copper oxide. From the EXAFS studies, the coordination of Cu was determined to have four equatorial oxygen(nitrogen) ligands at 1.96 Å and two axial oxygen ligands at 2.31 Å. Scanning-electron microscopy studies revealed the distribution of Cu within the seedlings tissues, predominantly accumulated in the cortical and vascular (xylem) regions of root tissues. In the stem, most of the Cu was found within the xylem tissue. However, the deposition of Cu within the leaf tissues was in the parenchyma. The present study demonstrates the mechanisms employed by S. drummondii for Cu uptake and its biotransformation.     

Leaching and degradation of 21 pesticides in a full-scale model biobed

Filling and cleaning of pesticide sprayers presents a potential risk of pollution of soil and water. Three different solutions for handling sprayers have been suggested: Filling and cleaning in the field, filling and cleaning on hard surfaces with collection of the waste water, and filling and cleaning on a biobed, which is an excavation lined with clay and filled with a mixture of chopped straw, sphagnum and soil with turf on top, and with increased sorption capacity and microbial activity for degradation of the pesticides. In the present study the degradation and leaching of 21 pesticides (5 g of each) was followed in an established full-scale model biobed. Percolate was collected and analysed for pesticide residues, and the biobed material was sampled at three different depths and analysed by liquid chromatography double mass spectrometry (LC-MSMS). During the total study period of 563 days, no traces of 10 out of 21 applied pesticides were detected in the percolate (detection limits between 0.02 and 0.9 μg l⁻¹) and three pesticides were only detected once and at concentrations below 2 μg l⁻¹. During the first 198 days before second application, 14% of the applied herbicide bentazone was detected in the leachate with maximum and mean concentrations of 445 and 172 μg l⁻¹, respectively. About 2% of the initial mecoprop and fluazifop dose was detected in the percolate, with mean concentrations of 23 μg l⁻¹, while MCPA and dimethoate had mean concentrations of 3.5 and 4.7 μg l⁻¹, respectively. Leachate concentrations for the remaining pesticides were generally below the detection limit (0.02–0.9 μg l⁻¹, below 1% of applied). Sorption studies of five pesticides showed that compounds with a low K_d value appeared in the leachate. After 169 days, all pesticides in the biobed profile were degraded to a level below 50% of the calculated initial dose. Pesticides with K_oc values above 100 were primarily found in the uppermost 10 cm and degraded slowest due to the low bioavailability. The 11 most degradable pesticides were all degraded such that less than 3% remained in the biobed after 169 days.

Following second pesticide application of the biobed, leachate was sampled 215 and 365 days after the treatment. This showed the same pesticides to be leached out and at concentrations comparable to those of the first treatment. The same pesticides as after the first treatment were retained in the biobed.     

Fate of cancerostatic platinum compounds in biological wastewater treatment of hospital effluents

The present work focuses on the fate of two cancerostatic platinum compounds (CPC), cisplatin and carboplatin, as well as of two inorganic platinum compounds, [PtCl₄]²⁻ and [PtCl₆]²⁻ in biological wastewater treatment. Laboratory experiments modelling adsorption of these compounds onto activated sludge showed promising specific adsorption coefficients K_D and K_OC and Freundlich adsorption isotherms. However, the adsorption properties of the investigated substances were differing significantly. Adsorption decreased following the order cisplatin > [PtCl₆]²⁻ > [PtCl₄]²⁻ > carboplatin. Log K_D-values were ranging from 2.5 to 4.3 , log K_OC from 3.0 to 4.7.

A pilot membrane bioreactor system (MBR) was installed in a hospital in Vienna and fed with wastewater from the oncologic in-patient treatment ward to investigate CPC-adsorption in a sewage treatment plant. During three monitoring periods Pt-concentrations were measured in the influent (3–250 μg l⁻¹ Pt) and the effluent (2–150 μg l⁻¹ Pt) of the treatment plant using ICP-MS. The monitoring periods (duration 30 d) revealed elimination efficiencies between 51% and 63% based on averaged weekly input–output budgets. The derived log K_D-values and log K_OC-values ranged from 2.4 to 4.8 and from 2.8 to 5.3, respectively. Species analysis using HPLC-ICP-MS proofed that mainly carboplatin was present as intact drug in the influent and – due to low log K_D – in the effluent of the MBR.     

Determination and distribution characteristics of degradation products of nonylphenol polyethoxylates in the rivers of Taiwan

Concentrations of degradation products of nonylphenol polyethoxylates (NPEOs) were analyzed in river water samples in order to determine the distribution characteristic of these alkylphenolic compounds in 18 major rivers of Taiwan. The degradation products of NPEOs were detected in all river samples, with the dicarboxylates alkylphenolic degradation products (CAPEC) being detected most frequently and at the highest concentrations. Concentrations of NP and NP1EO in rivers ranged from n.d. to 5.1 μg l⁻¹ and n.d. to 0.5 μg l⁻¹, respectively. The total concentrations of shortened carboxylates (i.e., NP1EC + NP2EC + NP3EC) and dicarboxylates alkylphenolic degradation products (CAP1EC + CAP2EC) ranged from n.d. to 63.6 μg l⁻¹ and n.d. to 94.6 μg l⁻¹, respectively. Concentrations of NP2EC, NP3EC and all CAPEC residues were determined semi-quantitatively by comparing with the internal standard. Significantly higher concentrations of CAPEC residues were detected in the river waters as compared to those of NP, NP1EO and NPEC degradation products and the average proportions of these compounds in the samples of the rivers were as follows: NP + NP1EO was 5 ± 2.5%, total NPEC was 25 ± 12%, and total CAPEC was 70 ± 12%. The high concentration ratios of CAPEC/NPEC illustrate that aerobic biodegradation plays a main route in the fate of NPEO in the rivers of Taiwan.     

Concentrations of chlorine, bromine and iodine in Japanese rivers

Concentrations of halogens (Cl, Br and I) in 30 Japanese rivers were measured by ion chromatography and inductively coupled plasma mass spectrometry to understand their behavior in the terrestrial environment. Concentrations of Cl, Br and I in each river, obtained at 10 sampling points from the upper stream to the river mouth, tended to increase near the river mouth. The ranges of geometric means of Cl, Br and I in each river were 1.0–19.4 mg l⁻¹, 2.5–67.9 μg l⁻¹, and 0.18–8.34 μg l⁻¹, respectively. To compare halogen behavior, the concentration ratios, Br/Cl and I/Cl, were calculated. The Br/Cl range was (2.3–7.8) × 10⁻³ (geometric mean: 3.74 × 10⁻³), and it was nearly constant except for the Yoneshiro river. It was estimated that 60–80% of total Br in the middle to lower parts of this river was the excess Br. The Br chemical form in all the rivers is generally considered to be Br⁻. The I/Cl ratios had different trends in rivers flowing into the Japan Sea and Pacific Ocean, possibly due to the different geological features in the river catchments.     

Compound-specific chlorine isotope analysis of polychlorinated biphenyls isolated from Aroclor and Clophen technical mixtures

The combined electrochemical oxidation-solar-light/immobilized TiO₂ film process was conducted to degrade an azo dye, Reactive Black 5 (RB5). The toxicity was also monitored by the Vibrio fischeri light inhibition test. The electrochemical oxidation rapidly decolorized RB5 (55, 110 μM) with a supporting electrolyte of 2 g l⁻¹ NaCl at current density 277 A m⁻² and pH 4. However, TOC mineralization and A₃₁₀ removal were low. Additionally, the treated solution showed high biotoxicity. RB5 at 110 μM significantly retarded the de-colorization efficiency by using the solar-light/immobilized TiO₂ film process. The combined electrochemical oxidation-solar-light/immobilized TiO₂ process effectively increased the removal of color, A₃₁₀, and TOC. The toxicity was also significantly reduced after 3 h of solar irradiation. The results indicated that the low-cost combined process is a potential technique for rapid treatment of RB5.     

Methane fluxes from tundra soils and snowpack in the maritime Antarctic

Methane fluxes were measured from three exposed tundra sites and four snowpack sites on the Fildes Peninsula in the maritime Antarctic in the summertime of 2002. The average fluxes at two normal tundra sites were −15.3 μg m⁻² h⁻¹ and −14.3 μg m⁻² h⁻¹, respectively. The fluxes from tundra site with fresh penguin dropping addition showed positive values with the average of 36.1 μg m⁻² h⁻¹, suggesting that the deposition of fresh droppings greatly enhanced CH₄ emissions from the poor Antarctic tundra during penguin breeding periods. The summertime variation in CH₄ flux was correlated with surface ground temperature and the precipitation. The correlation between the flux and PT₀, which is the product of the precipitation and surface ground temperature, was quite strong. The diurnal cycle of CH₄ flux from the tundra soils was not obtained due to local fluky weather conditions. The fluxes through four snowpack sites were also obtained by the vertical CH₄ concentration gradient and their average fluxes were −46.5 μg m⁻² h⁻¹, −28.2 μg m⁻² h⁻¹, −46.4 μg m⁻² h⁻¹ and −17.9 μg m⁻² h⁻¹, respectively, indicating that tundra soils under snowpack also consume atmospheric CH₄ in the maritime Antarctic; therefore these fluxes could constitute an important part of the annual CH₄ budget for Antarctic tundra ecosystem.     

Kinetics of nitromusk compounds degradation in water by ultraviolet radiation and hydrogen peroxide

The photodegradation of five representative nitromusk compounds in water has been performed in a stirred batch photoreactor with a UV low-pressure immersed mercury lamp, at constant temperature and different doses of hydrogen peroxide. The rate constants have been calculated on the basis of experimental data and a postulated first-order kinetic model. The rate constants, at 298 K and a dose of 1.1746 μmol l⁻¹ H₂O₂ ranges from 0.3567 × 10⁻³ s⁻¹ for musk tibetene, to 1.785 × 10⁻³ s⁻¹ for musk ambrette.     

Assessment of toxicity of a glyphosate-based formulation using bacterial systems in lake water

A new Aeromonas bioassay is described to assess the potential harmful effects of the glyphosate-based herbicide, Roundup^®, in the Albufera lake, a protected area near Valencia. Viability markers as membrane integrity, culturability and β-galactosidase production of Aeromonas caviae were studied to determine the influence of the herbicide in the bacterial cells. Data from the multifactor analysis of variance test showed no significant differences (P > 0.05) between A. caviae counts of viability markers at the studied concentrations (0, 50 and 100 mg l⁻¹ of glyphosate).

The effects of Roundup^® on microbial biota present in the lake were assessed by measuring the number of indigenous mesophilic Aeromonas in presence of different amounts of the herbicide at 0, 50 and 100 mg l⁻¹ of glyphosate. In samples containing 50 and 100 mg l⁻¹ of glyphosate a significant (P < 0.05) increase in Aeromonas spp. counts and accompanying flora was observed.

The acute toxicity of Roundup^® and of Roundup^® diluted with Albufera lake water to Microtox^® luminescent bacterium (Vibrio fischeri) also was determined. The EC₅₀ values obtained were 36.4 mg l⁻¹ and 64.0 mg l⁻¹ of glyphosate respectively. The acidity (pH 4.5) of the herbicide formulation was the responsible of the observed toxicity.     

UV-H2O2 based AOP and its integration with biological activated carbon treatment for DBP reduction in drinking water

The presence of disinfection byproducts (DBPs) such as trihalomethanes (THMs) and haloacetic acids (HAAs) in drinking water is of great concern due to their adverse effects on human health. Emerging regulation limiting the concentration of DBPs in drinking water has increased demands for technologies and processes which reduce the formation of DBPs in drinking water. In this study, UV-H₂O₂ based advance oxidation process (AOP) was used to treat raw surface water. Experiments were conducted using low pressure mercury vapor UV lamps in collimated beam and flow-through annular photoreactors. The effect of UV fluence (0–3500 mJ cm⁻²) and hydrogen peroxide concentration (0–23 mg l⁻¹) in reducing the concentration of THMs and HAAs was examined. The UV-H₂O₂ AOP was then coupled with a downstream biological activated carbon (BAC) treatment to assess the synergetic benefits of combining the two treatments. It was observed that UV-H₂O₂ AOP was only effective at reducing DBPs at UV fluences of more than 1000 mJ cm⁻²and initial H₂O₂ concentrations of about or greater than 23 mg l⁻¹. However, the combined AOP–BAC treatment showed significant reductions of 43%, 52%, and 59% relative to untreated raw water for DBPs, TOC, and UV₂₅₄, respectively.     

Selective adsorption of phenanthrene dissolved in surfactant solution using activated carbon

Selective adsorption of a hazardous hydrophobic organic compound (HOC) by activated carbon as a means of recovering surfactants after a soil washing process was investigated. As a model system, phenanthrene was selected as a representative HOC and Triton X-100 as a nonionic surfactant. Three activated carbons that differed in size (Darco 20–40 (D20), 12–20 (D12) and 4–12 (D4) mesh sizes) were used in adsorption experiments. Adsorption of surfactant onto activated carbon showed a constant maximum above the critical micelle concentration, which were 0.30, 0.23, 0.15 g g⁻¹ for D20, D12, and D4, respectively. Selectivity for phenanthrene to Triton X-100 was much higher than 1 over a wide range of activated carbon doses (0–6 g l⁻¹) and initial phenanthrene concentrations (10–110 mg l⁻¹). Selectivity generally increased with decreasing particle size, increasing activated carbon dose, and decreasing initial concentration of phenanthrene. The highest selectivity was 74.9, 57.3, and 38.3 for D20, D12, and D4, respectively, at the initial conditions of 10 mg l⁻¹ phenanthrene, 5 g l⁻¹ Triton X-100 and 1 g l⁻¹ activated carbon. In the case of D20 at the same conditions, 86.5% of the initial phenanthrene was removed by sorption and 93.6% of the initial Triton X-100 remained in the solution following the selective adsorption process. The results suggest that the selective adsorption by activated carbon is a good alternative for surfactant recovery in a soil washing process.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

On the performance of Fe and Fe,F doped Ti-Pt/PbO2 electrodes in the electrooxidation of the Blue Reactive 19 dye in simulated textile wastewater

The electrochemical performance of pure Ti–Pt/β-PbO₂ electrodes, or doped with Fe and F (together or separately), in the oxidation of simulated wastewaters containing the Blue Reactive 19 dye (BR-19), using a filter-press reactor, was investigated and then compared with that of a boron-doped diamond electrode supported on a niobium substrate (Nb/BDD). The electrooxidation of the dye simulated wastewater (volume of 0.1 l, with a BR-19 initial concentration of 25 mg l⁻¹) was carried out under the following conditions: current density of 50 mA cm⁻², volume flow rate of 2.4 l h⁻¹, temperature of 25 °C and electrode area of 5 cm². The performances of the electrodes in the dye decolorization were quite similar, achieving 100% decolorization, and in some cases 90% decolorization was achieved by applying only ca. 0.3 A h l⁻¹ (8 min of electrolysis). The reduction of the simulated wastewater organic load, monitored by its total organic carbon content (TOC), was greater for the Ti–Pt/β-PbO₂–Fe,F electrode obtained from an electrodeposition bath containing 1 mM Fe³⁺ and 30 mM F⁻. In this case, after 2 h of electrolysis the obtained TOC reduction was 95%, while for the pure β-PbO₂ and the Nb/BDD electrodes the reductions were 84% and 82%, respectively.     

Cadmium accumulation and Cd-binding proteins in marine invertebrates--a radiotracer study

Tissue and subcellular accumulation of cadmium were studied in different tissues of three marine invertebrates (blue mussel Mytilus edulis, the tunicate Ciona intestinalis and the sea star Asterias rubens) using radioactive ¹⁰⁹Cd as a tracer. The organisms were exposed to 0.05, 2 and 50 μg Cd l⁻¹ for 21 days. Quantitative data were obtained by dissecting, weighing and subsequently measuring radioactivity in organs and tissues. Differences between each exposure and each tissue with regard to the amount of radioactivity and metallothionein (MT) content were evaluated. Obvious interspecies differences in Cd accumulation were observed, as well as differences between tissues of the three species. The highest concentrations of Cd in all exposure treatments were found in the hepatopancreas of M. edulis and body wall of A. rubens. Taking all treatments into account, Cd accumulation in the tunic of C. intestinalis was high compared to other tissues from this species. Over 60% of Cd was present in the S50 fraction in all treatments in all three species. Metallothionein levels were increased at the highest Cd-exposure in all species and tissues, except in branchial pharynx of C. intestinalis where the highest MT level was reached following exposure to 2 μg Cd l⁻¹. The most surprising finding was that even the lowest Cd exposure concentration (0.05 μg Cd l⁻¹) caused MT induction in pyloric caeca of A. rubens, but there was no dose-dependent increase in MT at higher exposure levels.     

A qualitative field method for monitoring pesticides in the edge-of-field runoff

A field method is described, which allows the qualitative estimation of pesticide contamination in the edgeof-field runoff. The method employs cheap and easy-to-use runoff sampling bottles, which were installed in an agricultural stream catchment over a period of three growing seasons. During this time 18 runoff events were detected, in nine of which insecticide contamination was measured (maximum concentrations: lindane 0.7 μg l⁻¹ and 12.7 μg kg⁻¹, parathion 20 μg l⁻¹ and 728 μg kg⁻, fenvalerate 18.4 μg 1-1 and 924 μg kg⁻¹). These insecticides were detected mainly as particle-bound chemicals. On about 80 % of the occasions the presence or absence of runoff measured in the field was in agreement with a simulation of runoff presence or absence using the runoff model KINEROS.     

Determination of 4-tert-octylphenol, 4-nonylphenol and bisphenol A in surface waters from the Haihe River in Tianjin by gas chromatography-mass spectrometry with selected ion monitoring

The estrogenic pollutants 4-tert-octylphenol (OP), 4-nonylphenol (NP) and bisphenol A (BPA) were determined in surface water samples from the Haihe River, Tianjin, China. The analytes were extracted and concentrated from 300 ml acidified water samples by liquid–liquid extractions using dichloromethane, derivatized with trifluoroacetic anhydride, and quantified by gas chromatography–mass spectrometry (GC–MS) with selected ion monitoring (SIM). Among the samples collected from 14 sampling sites, only one sample was found to have a relatively high concentration of BPA (8.30 μg l⁻¹) and NP (0.55 μg l⁻¹). The concentrations of OP, NP and BPA in the other samples were in the range of 18.0–20.2, 106–296 and 19.1–106 ng l⁻¹, respectively. Recoveries for OP, NP and BPA in the spiked water samples were all over 80%.     

Effects of different quinoid redox mediators on the removal of sulphide and nitrate via denitrification

The impact of different quinoid redox mediators on the simultaneous conversion of sulphide and nitrate in a denitrifying culture was evaluated. All quinones evaluated, including anthraquinone-2,6-disulphonate (AQDS), 2-hydroxy-1,4-naphthoquinone and 1,2-naphthoquinone-4-sulphonate (NQS) were reduced by sulphide under abiotic conditions. NQS showed the highest reduction rate by sulphide (132 μmol h⁻¹) and promoted the maximum rate of sulphide oxidation (87 μmol h⁻¹) by denitrifying sludge, which represents an increase of 44% compared to the control lacking quinones. The reduced form of AQDS (AH₂QDS) served as an electron donor for the microbial reduction of nitrite and N₂O, which represents the first demonstration of hydroquinones supporting the microbial reduction of denitrifying intermediates. The results taken as a whole suggest that some quinones may significantly increase the rate of removal of S and N under denitrifying conditions.