Coal dust particle size survey of US mines

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of US coal mines. The last comprehensive survey of this type was performed in the 1920s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust.

Dust samples were collected by MSHA inspectors from several mines in each of MSHA's 10 bituminous Coal Mine Safety and Health Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low-temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920s. This finer size coal dust in intake airways would require more incombustible matter to be effectively inerted than the 65% incombustible specified in current regulations.     

Particle size and surface area effects on explosibility using a 20-L chamber

The Mine Safety and Health Administration (MSHA) specification for rock dust used in underground coal mines, as defined by 30 CFR 75.2, requires 70% of the material to pass through a 200 mesh sieve (<75 μm). However, in a collection of rock dusts, 47% were found to not meet the criteria. Upon further investigation, it was determined that some of the samples did meet the specification, but were inadequate to render pulverized Pittsburgh coal inert in the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) 20-L chamber. This paper will examine the particle size distributions, specific surface areas (SSA), and the explosion suppression effectiveness of these rock dusts. It will also discuss related findings from other studies, including full-scale results from work performed at the Lake Lynn Experimental Mine. Further, a minimum SSA for effective rock dust will be suggested.     

Observations of microscopic characteristics of post-explosion coal dust samples

To reveal the microscopic characteristics of the post-explosion coal dust samples, coal dust explosion tests were performed in a 20 L spherical vessel. The explosion characteristic parameters, such as the maximum pressure (P_max), the maximum rate of pressure rise ((dP/dt)_max), ignition time (t) and the deflagration index (K_St) were recorded. Meanwhile, the post-explosion dust samples were collected and analyzed. The research efforts include particle size distribution analysis, SEM analysis and FTIR analysis of dust samples before and after the explosion. The particle size range of post-explosion dust samples became wider according to the mass percent analysis. The microscopic appearance of samples in same particle size range showed some similarity. The porous structure of dust samples was observed by improving the SEM magnification. The chemical structure of dust samples before and after explosion was analyzed by FTIR.     

Collecting representative dust samples: A comparison of various sampling methods in underground coal mines

Former methods used in the U.S. to assess hazardous and explosible coal dust date back to the 1950s. As mining technologies advanced, so too have the hazards. Given the results of the recent coal dust particle size survey and full-scale experimental mine explosion tests, the National Institute for Occupational Safety and Health (NIOSH) recommended a new minimum standard, in the absence of background methane, of 80% total incombustible content (TIC) be required in the intake airways of bituminous coal mines, replacing the previous 65% TIC requirement. Most important to monitoring and maintaining the 80% TIC is the ability to effectively collect and analyze representative dust samples that would likely disperse and participate in dust explosion propagation. Research has shown that dust suspended on elevated surfaces is usually finer, more reactive, and more readily dispersible while floor deposits of dust are generally coarser and more difficult to disperse given the same blast of air. The roof, rib, and floor portions of the dust samples were collected and analyzed for incombustible content separately and the results were compared to a band sample of the roof, rib, and floor components. Results indicate that the roof and rib dust samples should be kept separate from floor dust samples and considered individually for analyses. The various experimental collection methods are detailed along with preferred sampling approaches that improve the detectability of potentially hazardous accumulations of explosible dust.     

Explosibility of hydrogen–graphite dust hybrid mixtures

To evaluate the hazard of combined hydrogen/dust explosions under severe accident conditions in International Thermonuclear Experimental Reactor (ITER), standard method of 20-L-sphere was used to measure the explosion indices of 4-μm fine graphite dust in lean hydrogen/air mixtures. The mixtures were ignited by a weak electric spark. The tested fuel concentrations were 8–18 vol% H₂ and 25–250 g/m³ dust. If the hydrogen content is higher than 10 vol%, the dust constituent can be induced to explode by the hydrogen explosion initiated by a weak electric spark. Depending on the fuel component concentrations, the explosions proceed in either one or two stages. In two-stage explosions occurring at low hydrogen and dust concentrations, the mixture ignition initiates first a fast hydrogen explosion followed by a slower phase of the dust explosion. With increasing dust concentration, the dust explodes faster and can overlap the hydrogen-explosion stage. At higher hydrogen concentrations, the hybrid mixtures explode in one stage, with hydrogen and dust reacting at the same time scale. Maximum overpressures of hybrid explosions are higher than those observed with hydrogen alone; maximum rates of pressure rise are lower in two-phase explosions and, generally, higher in one-stage explosions, than those characteristic of the corresponding H₂/air mixtures.     

Experimental mine and laboratory dust explosion research at NIOSH

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coals, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane–air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.     

Explosibility of cork dust in methane/air mixtures

Explosibility studies of hybrid methane/air/cork dust mixtures were carried out in a near-spherical 22.7 L explosibility test chamber, using 2500 J pyrotechnic ignitors. The suspension dust burned as methane/air/dust clouds and the uniformity of the cork dust dispersion inside the chamber was evaluated through optical dust probes and during the explosion the pressure and the temperature evolution inside the reactor were measured. Tested dust particles had mass median diameter of 71.3 μm and the covered dust cloud concentration was up to 550 g/m³. Measured explosions parameters included minimum explosion concentration, maximum explosion pressures and maximum rate of pressure rise. The cork dust explosion behavior in hybrid methane/air mixtures was studied for atmospheres with 1.98 and 3.5% (v/v) of methane. The effect of methane content on the explosions characteristic parameters was evaluated. The conclusion is that the risk and explosion danger rises with the increase of methane concentration characterized by the reduction of the minimum dust explosion concentration, as methane content increases in the atmosphere. The maximum explosion pressure is not very much sensitive to the methane content and only for the system with 3.5% (v/v) of methane it was observed an increase of maximum rate of pressure rise, when compared with the value obtained for the air/dust system.     

基于20L球形爆炸装置的甲烷煤尘混合爆炸实验

利用实验室自行设计的20L球形爆炸装置,对煤尘及甲烷煤尘混合物的爆炸特性进行了研究。结果表明:无论有无甲烷,煤尘的最大爆炸压力随煤尘浓度增加呈现先升高后降低的变化趋势,并且均在在煤尘浓度为600g/m3时均达到最大值。同时,甲烷的加入明显提高了煤尘最大爆炸压力值,而且随着甲烷浓度的增加,最大爆炸压力增幅先增加后降低,在甲烷5%时增幅最大。煤尘的爆炸持续时间随煤尘浓度增加呈现先降低后升高的特点,甲烷存在时有同样规律,但是有甲烷时爆炸持续时间明显降低,而且随着甲烷含量的增加,煤尘的爆炸持续时间降低幅度不断增加,在甲烷5%以后趋于稳定。实验结果对生产实践有一定的指导作用。     

Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions

Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture.It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence.     

Effects of obstacles and deposited coal dust on characteristics of premixed methane–air explosions in a long closed pipe

An experimental system including pressure transducer, electric spark ignition device, data acquisition and control unit was set up to investigate methane–air explosions in a horizontal pipe closed at both ends with or without the presence of obstacles and deposited coal dust. The experimental results show that explosion characteristics depended on the methane content, on the layout of obstacles, and on the deposited coal dust. Pressure fluctuation with a frequency of 150 Hz appeared in its crest when the methane content was close to the stoichiometric ratio (9.5% methane percentage by volume). The pressure rise rate increased locally when a single obstacle was mounted in the pipe, but it had little effect on the pressure peak. Repeated obstacles mounted in the pipe caused the pressure to rise sharply, and the mean maximum explosion overpressure increased with the increase of the obstacle’s number. The amplitude of pressure fluctuation was reduced when deposited coal dust was paved in the bottom of the pipe. However, when repeated obstacles were arranged inside, the maximum overpressures were higher with coal dust deposited than pure gas explosions.     

Analysis of “high-dollar” value safety and health citations and orders for the US coal mines

This paper presents an analysis of a “high-dollar” value safety and health citations and orders for the US coal mines using the Mine Safety and Health Administration (MSHA) data. Term “high-dollar” value relates to penalty of $10,000 and more per citation or order. The study was based on historical MSHA data for the period from 01/01/2009 to 12/31/2009. Data shows that there were 1161 “high-dollar” value citations and orders in 2009 with a total penalty of almost $31-million. The most cited standard was 75.400 – “Accumulation of combustible material” with a 259 “high-dollar” value citations and total penalty of almost $5.9-million. Among all US states, the West Virginia coal mines recorded the highest number of citations and the total penalty value. Results of this study can be used by coal mining industry to help in prioritizing resource allocations and determining control strategies.     

Pilot sample risk analysis for underground coal mine fires and explosions using MSHA citation data

After three decades of sustained continuous improvement of mine safety performances in the US, mine disasters in 2006 and 2007 compromised an excellent record and presented new challenges and vulnerabilities for the underground coal mining industry. In the aftermath of the incidents, formal investigations and new scrutiny of mine safety by the US Congress and expert study groups followed. The US Congress passed the Mine Improvement and New Emergency Response Act of 2006 (MINER Act), which mandated new laws to address the issues, including those related to mine fires and explosions from which miners must be protected. The National Mining Association-sponsored Mine Safety Technology and Training Commission report highlighted the role of risk analysis and management in identifying and controlling major hazards, such as fires and explosions. In this paper an approach is given for analyzing the risks for fires and explosions based on the Mine Safety and Health Administration citation database. Using 2006 citation data and focusing on subsystem failures, the methodology is applied to a database for a pilot sample of underground coal mines stratified by mine size and state.     

Analysis on research trends with dust explosions by bibliometric approach

Highly destructive combustible dust explosions, which is prone to cause secondary explosion, has been a concern in industrial processes. To understand the current development and status of research on dust explosions, 1276 publications related to dust explosions from 1998 to 2021 were indexed through the Web of Science Core Collection database. CiteSpace and VOSviewer were used to visualize and analyze the collected literature information. The number of articles related to dust explosions has increased from 12 in 1998 to 191 in 2021. China, the United States, and Canada are the major contributors in this field. Dalhousie University, Beijing Institute of Technology, and Dalian University of Technology are at the core of dust explosion research. Wei Gao, Paul Amyotte, and Chi-Min Shu are the most prolific researchers. Journal of Loss Prevention in the Process Industries, Powder Technology, and Process Safety and Environmental Protection are the major sources of publications related to dust explosions. The research topic of dust explosions mainly evolves into four aspects: explosion characteristics and influencing factors, research media, explosion suppression, and numerical simulation. New research hotspots have appeared related to gas–dust hybrid mixtures, nanomaterials, and powder suppressants. The results can help researchers in the dust explosion field to quickly determine the research frontier and the overall situation.     

Methane/coal dust/air explosions and their suppression by solid particle suppressing agents in a large-scale experimental tube

Methane/coal dust/air explosions under strong ignition conditions have been studied in a 199 mm inner diameter and 30.8 m long horizontal tube. A fuel gas/air manifold assembly was used to introduce methane and air into the experimental tube, and an array of 44 equally spaced dust dispersion units was used to disperse coal dust particles into the tube. The methane/coal dust/air mixture was ignited by a 7 m long epoxypropane mist cloud explosion. A deflagration-to-detonation transition (DDT) was observed, and a self-sustained detonation wave characterized by the existence of a transverse wave was propagated in the methane/coal dust/air mixtures.The suppressing effects on methane/coal dust/air mixture explosions of three solid particle suppressing agents have been studied. Coal dust and the suppressing agent were injected into the experimental tube by the dust dispersion units. The length of the suppression was 14 m. The suppression agents examined in this study comprised ABC powder, SiO₂ powder, and rock dust powder (CaCO₃). Methane/coal dust/air explosions can be efficiently suppressed by the suppression agents characterized by the rapid decrease in overpressure and propagating velocity of the explosion waves.     

Explosibility and thermal decomposition behavior of nitrile rubber dust in industrial processes

The formation of nitrile rubber (NBR) dust clouds during processing can lead to a potential dust explosion under certain conditions. However, the potential explosion hazard posed by NBR dust is usually overlooked by enterprises. In this paper, the explosive properties of NBR dust are investigated using a Hartmann tube, a G-G furnace, and a 20 L explosion chamber. The results showed that NBR dust could cause explosions severe enough to be classified as St-1. In addition, the thermal decomposition behavior of NBR dust under combustion conditions was investigated using a combination of thermogravimetric analysis coupled with Fourier transform infrared spectroscopy (TGA-FTIR). The results indicated that in the early stage, NBR dust mainly undergoes self-thermal decomposition to produce a large amount of combustible gas, which combines with oxygen to form a mixed gas and cause a gas-phase explosion. In addition, the participation of oxygen could lower the initial temperature of NBR dust thermal decomposition. As a result, decomposition occurred more quickly and a large amount of combustible gas was produced, thus expanding the range of dust explosions. Furthermore, these combustible gases exhibit varying degrees of toxicity, seriously affecting the life and health safety of relevant personnel. This work provides theoretical guidance for the development of safe procedures to prevent and address problems during NBR dust processing in enterprises.     

Effectiveness of dust dispersion in the 20-L Siwek chamber

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m³ dust explosion chambers.The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m³ and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.     

煤尘与矿井特大爆炸伤亡事故的关系

为了阐明煤尘爆炸或煤尘参与爆炸的严重危害,在分析了煤尘爆炸与瓦斯爆炸各自特点的基础上,通过对近年来我国瓦斯、煤尘爆炸事故的情况分析,特别是对典型的重大恶性瓦斯煤尘爆炸事故的分析,指出煤尘对煤矿发生重大恶性爆炸事故的影响,并说明了沉积煤尘防治对控制重大瓦斯煤尘爆炸事故的作用。     

瓦斯煤尘爆炸特性及抑爆方法研究进展

为探究瓦斯煤尘爆炸特性及抑爆机理,本文通过一系列实验,研究瓦斯、煤尘爆炸的速度和温度等特征,提出利用图像相关系数法和辐射测温原理计算火焰传播速度及温度场变化,定量分析影响煤尘爆炸的因素以及产物变化规律,揭示煤尘爆炸的宏微观机制。结果表明:火焰分形维数可以用来反应瓦斯爆炸强度,即当分形维数更接近2.2937时爆炸反应最为强烈,其爆炸过程中自由基最终生成浓度与CH 4初始浓度呈倒U型关系;当量比对煤粉火焰爆炸压力及速度也有一定影响,在最佳当量比的2倍左右时可以达到最大爆炸压力和最大火焰传播速度。另外本文亦采用泡沫陶瓷对瓦斯的多次爆炸和连续爆炸进行抑爆,发现不同厚度和孔隙的泡沫陶瓷具有不同的抑制效果,孔隙较大的泡沫陶瓷对爆炸能量有较好的抑制作用。     

A methodology for assessing underground coal mines for high safety-related risk

In 2008 the authors developed a methodology for assessing underground coal mines for high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later using the same stratified pilot sample of 31 mines, injury measures and MSHA citation data were combined into a Safe Performance Index (SPI). Using 2009 data, the database was expanded to 107 mines, which is a 30% sampling of all underground coal mines. The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. The methodology can be used to assist companies, the Mine Safety and Health Administration, or state agencies in targeting mines with high risk for serious injuries and elevated citations for remediation of their violation and/or injury experience.     

The influence of air flow on maximum explosion characteristics of dust–air mixtures

A standard spherical apparatus for measuring explosion characteristics was modified to give increased and controlled turbulence within a dust–air mixture. This was intended to mimic the local effects which may occur during industrial dust explosions, particularly secondary ones which may develop in ducts or mine galleries where the initial explosion causes an increased air velocity and suspension of further quantities of dust.The results show that there may be a doubling of the maximum explosion pressure and of the rate of pressure rise during the explosion under more turbulent conditions. This is significant for modelling of dust explosions and suggests that explosion relief may be inadequate if this factor is not taken into consideration.The modified apparatus therefore gives a laboratory method for assessing the effect of turbulence in dust explosions.