Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

V2O5/TiO2催化剂中毒机理的试验研究

选择性催化还原(SCR)催化剂是SCR烟气脱硝技术的核心,是整个SCR系统脱硝效率和经济性的决定因素.本文工作的主要研究思路是以钒钛SCR催化剂为研究对象,研究了H2O和SO2,以及相同含量下K、Na、Ca、Pb的氧化物对钒钛催化剂NO转化率的影响.H2O的存在会抑制V2O5/TiO2催化剂脱硝活性,而SO2在一定程度上促进(V2O5/TiO2)催化剂的SCR脱硝反应,提高NO转化率;碱金属K对钒钛催化剂的钝化作用都是最强,K2O和Na2O的掺入会抑制钒钛催化剂上V2O5的还原能力,而CaO和PbO的掺入对钒钛催化剂上V2O5的还原能力影响较小.     

Simulated-sunlight-activated photocatalysis of Methylene Blue using cerium-doped SiO2/TiO2 nanostructured fibers

Cerium-doped SiO₂/TiO₂ nanostructured fibers were fabricated by electrospinning technology. The prepared fibers were characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Using the fibers as catalysts, photocatalytic degradation of Methylene Blue (MB) aqueous solution was carried out under simulated sunlight. The 0.2% Ce doping proved to be the optimal concentration for the doping of TiO₂/SiO₂, compared to other Ce-doped molar concentrations. The 0.2% Ce-doped SiO₂/TiO₂ fibers exhibited higher photocatalytic activity than industrial Degussa P25 and the samples doped with only Ce or SiO₂. The reasons for improving the photocatalytic activity were also discussed. Several operational parameters were studied, which showed that the photocatalytic efficiency of MB was influenced by parameters such as the initial dye concentration, the initial pH, inorganic anions, and so on. In addition, the influences of an electron acceptor and a radical scavenger suggested that OH was the dominant photooxidant during the photocatalytic process. The reuse evaluation of the fibers indicated that their photocatalytic activity had good stability.     

Effects of synthesis methods on catalytic activities of CoOx–TiO2 for low-temperature NH3-SCR of NO

A series of cobalt doped TiO_2(Co-TiO_2) and Co Oxloaded TiO_2(Co/TiO_2) catalysts prepared by sol–gel and impregnation methods respectively were investigated on selective catalytic reduction with NH_3(NH_3-SCR) of NO. It was found that Co-TiO_2 catalyst showed more preferable catalytic activity at low temperature range. From characterization results of XRD,TEM, Raman and FT-IR, Co species were proved to be doped into TiO_2 lattice by replaced Ti atoms. After being characterized and analyzed by NH_3-TPD, PL, XPS, EPR and DRIFTS, it was found that the better NH_3-SCR activities of Co-TiO_2 catalysts, compared with Co/TiO_2 catalyst, were ascribed to the formation of more oxygen vacancies which further promoted the production of more superoxide ions(O-2). The superoxide ions were crucial for the formation of low temperature SCR reaction intermediates(NO-3) by reacting with adsorbed NO molecule. Therefore, these aspects were responsible for the higher low temperature NH_3-SCR activity of Co-TiO_2 catalysts.     

溶胶粉末复合浸渍法制备颗粒状SCR脱硝催化剂的特性

针对以V₂O₅-WO₃/TiO₂为成分的颗粒状SCR脱硝催化剂在制备过程中存在的有效组分加载均匀性等问题,尝试了利用偏钛酸溶胶作为载体的催化剂生产方法.利用粉末/溶胶复合浸渍方式设计出4种催化剂的制备方法并分别制得样品.通过在不同温度条件下样品对烟气中NO_x成分去除效能的性能测试,以及进行相关的微观表征分析,研究比较了不同制备方式对催化剂特性的影响规律,旨在探索出一种合理、高效的催化剂制备工艺.结果表明:利用偏钛酸溶胶作为载体,同步浸渍加载WO₃和V₂O₅ 2种组分,相比传统的粉末浸渍和两步浸渍方式,该方法能够使浸渍组分在载体表面获得较高的覆盖率,并有效避免了浸渍组分溶出和重结晶现象的发生,所制得的催化剂样品具有较高的脱硝效率.      

BiOCl/TiO2的氯化改性及其新式光生自由基催化反应

采用溶胶凝胶法制备了BiOCl/TiO₂复合催化剂,透射电镜（TEM）照片显示,两种半导体分布均匀、相互连接,形成的异质结可以为电子传导提供有效通道.经过氯化处理的复合材料具备更强的光催化能力,在紫外光条件下对苯的降解率达到90%,是原BiOCl/TiO₂的2倍、纯TiO₂的10倍.本文利用X射线光电子能谱、红外光谱和电子顺磁共振,对表面氯化的机理进行研究.结果表明,氯元素以Ti—Cl的方式吸附在催化剂表面,在光照条件下光生空穴夺取一个电子,使其生成氯自由基,进而配合超氧、羟基,构成一种新型的三自由基光催化体系,使催化降解能力大幅提升.最后,利用实验方法得到了光生氯自由基的直接证据,并构建了该体系的光催化反应机理.     

Fe2O3/TiO2负载膨胀珍珠岩光催化降解罗丹明B

为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩（EP）为载体,采用溶胶-凝胶法,在不同煅烧氛围（O₂和/或NH₃）下制备Fe₂O₃/TiO₂负载EP的光催化复合材料〔Fe₂O₃-TEP（O₂）、Fe₂O₃-TEP（NH₃）、Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）〕,采用EDS（X-射线色散能谱）、BET（比表面积及孔径分析）、XRD（X射线衍射）、SEM（扫描电子显微镜）、XPS（X射线光电子能谱）等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO₂以锐钛矿型存在,Fe₂O₃的掺杂增强了TiO₂对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe₂O₃-TEP（O₂,NH₃）的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料（Fe₂O₃-TEP）经煅烧后所得矿相均一;Fe₂O₃掺杂TiO₂可形成Ti—O—Fe键,减小TiO₂固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O₂后NH₃煅烧条件下所得材料的光催化性能最佳.      

Influences of pH value in deposition-precipitation synthesis process on Pt-doped TiO2 catalysts for photocatalytic oxidation of NO

This work has been undertaken to study the influences of pH value on the characteristics and activity of photocatalyst by deposition-precipitation method during its preparation process. A series of Pt-modified TiO₂ were prepared by deposition-precipitation method at different pH values as well as wet impregnation method, and characterized by XRD, XPS, TEM, UV-Vis and photoluminescence (PL). It was found that the catalysts had the highest photocatalytic activity for NO conversion when pH value was kept at around 7. And the sample prepared by deposition-precipitation method showed higher activity than that by impregnation method. This was mainly due to their high value in highly-dispersed platinum oxides (PtOx) content on the surface of the catalysts. The results from UV-Vis absorption showed that highest absorbance was obtained for Pt/TiO₂ prepared at pH values of around 7. And PL spectra results indicated that the recombination rate of photogenerated electrons and holes of the samples prepared by deposition-precipitation method was lower than that prepared by impregnation method. And in the zeta potential study, the pH values for the isoelectric point of the preparing slurry of 0.05 wt.%Pt/TiO₂ and 0.5 wt.%Pt/TiO₂ were determined to be 6.5-8.5, which further confirmed the enrichment of PtOx dopants for the catalysts repapered when pH value was around 7.     

Fabrication of Bi2O3/TiO2 nanocomposites and their applications to the degradation of pollutants in air and water under visible-light

A nanoheterojunction composite photocatalyst Bi2O3/TiO2working under visible-light(λ 420 nm) was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.     

UV/TiO2/H2O2体系对制药废水二级出水的处理特性研究

以某制药企业的二级出水为研究对象,对比了UV/TiO₂、UV/H₂O₂、UV/TiO₂/H₂O₂ 3种高级氧化工艺的处理效果,利用自主设计的一体化光催化装置进行了连续动态试验,并通过凝胶渗透色谱（GPC）、傅里叶变换红外光谱（FT-IR）、三维荧光光谱（EEM）、斑马鱼急性毒性试验等方法研究了处理前后有机物特性和生物毒性的变化.结果表明,与UV/TiO₂和UV/H₂O₂体系相比,UV/TiO₂/H₂O₂光芬顿体系对有机物的去除效果更好,当TiO₂投加量为1 g·L^-1,H₂O₂投加量为100 mg·L^-1时,处理效果达到最佳.一体化光催化装置能够利用UV/TiO₂/H₂O₂光芬顿技术快速高效地降解二级出水中的有机污染物,反应30 min时COD去除率达到50%以上.经UV/TiO₂/H₂O₂深度处理后,废水中的大分子有机物分解转换为小分子,有机物中的不饱和结构明显减少,腐殖质等溶解性有机物基本降解完全.毒性试验结果表明,该二级出水的生物毒性经深度处理后显著降低,对斑马鱼胚胎不存在致畸致死效应.     

碱土金属钙沉积对Mn-Ce/TiO2低温SCR催化剂脱硝性能的影响

本研究采用浸渍法分别制备CaCl2、CaCO3和CaSO4这3种钙盐前驱体沉积的Mn-Ce/TiO2催化剂,通过分析催化剂活性与催化剂理化特性之间的关系,考察碱土金属钙沉积对Mn-Ce/TiO2低温SCR催化剂脱硝性能的影响.结果表明,钙的加入会导致催化剂中毒,且不同钙前驱体掺杂对催化剂中毒效应不同.CaCO3的沉积对Mn-Ce/TiO2催化剂脱硝效率的影响最小,而CaCl2沉积对催化剂活性抑制作用最为强烈.通过比表面积测试(BET)、X射线光电子能谱(XPS)、X射线晶体衍射(XRD)、程序升温脱附(TPD)等方法对不同催化剂进行表征发现,催化剂的晶型变化、孔道结构破坏、表面活性元素及酸性点位的减少是催化剂中毒的主要原因.     

Alkali resistance promotion of Ce-doped vanadium-titanic-based NH3-SCR catalysts

The effect of K deactivation on V_2O_5/WO_3-TiO_2 and Ce-doped V_2O_5/WO_3-TiO_2 catalysts in the selective catalytic reduction(SCR) of NOxby NH_3 was studied.Ce-doped V_2O_5/WO_3-TiO_2 showed significantly higher resistance to K deactivation than V_2O_5/WO_3-TiO_2.Ce-doped V_2O_5/WO_3-TiO_2 with K/V = 4(molar ratio) showed 90% NOxconversion at 350°C,whereas in this case V_2O_5/WO_3-TiO_2 showed no activity.The fresh and K-poisoned V_2O_5/WO_3-TiO_2 and Ce-doped V_2O_5/WO_3-TiO_2 catalysts were investigated by means of in situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS),NH_3-temperature progress decomposition(NH_3-TPD),X-ray photoelectron spectroscopy(XPS) and H2-temperature program reduction(H_2-TPR).The effect of Ce doping on the improving resistance to K of V_2O_5/WO_3-TiO_2 were discussed.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

以堇青石蜂窝陶瓷为载体的新型钒氧化物脱氮催化剂研究

以TiO₂/Al₂O₃/堇青石蜂窝陶瓷为载体,以V₂O₅-MoO₃-WO₃为活性组分,用于氨法选择性催化还原烟气中NO的新型催化剂,并对该催化剂的活性性能和微观结构进行了评价和表征.同时,将该催化剂的活性性能与其它几种活性组分相同但载体、制备方法、结构不同的催化剂进行了对比.对比结果表明,该新型催化剂能取得最好的选择性催化还原氮氧化物催化性能BET、FT IR、XPS表征实验结果表明,其高催化活性得益于大比表面积及大孔体积,而TiO₂/Al₂O₃/堇青石蜂窝陶瓷载体及其制备方法对获得好的催化剂构型起了至关重要的作用.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

Reduction of NO by CO using Pd-CeTb and Pd-CeZr catalysts supported on SiO2 and La2O3-Al2O3

The catalytic activity of Pd catalysts supported on Ce_0.73Tb_0.27O_x/SiO₂, Ce_0.6Zr_0.4O_x/SiO₂, Ce_0.73Tb_0.27O_x/La₂O₃-Al₂O₃ and Ce_0.6Zr_0.4O_x/La₂O₃-Al₂O₃ was studied using the reduction of NO by CO. The catalysts were characterized by X-ray fluorescence, surface area, X-ray diffraction, temperature-programmed reduction, CO chemisorption and oxygen storage capacity. Temperature-programmed reduction results indicated that Tb or Zr incorporation improves the reducibility and oxygen storage capacity. CO chemisorption data suggested the presence of large PdO particles due to the low CO/Pd ratio. No significant differences were obtained in light off temperatures (T_{Light off}) for all Pd catalysts and the most active was 1.5%Pd/Ce_0.6Zr_0.4O_x/SiO₂.     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

Effects of Ce on catalytic combustion of methane over Pd-Pt/Al2O3 catalyst

Activity and stability of 1%Pd-0.2%Pt/Al₂O₃ and 1%Pd-0.2%Pt/0.6%Ce/Al₂O₃ catalysts prepared by impregnation method for catalytic combustion of methane in air were investigated. The catalysts before and after reaction were characterized by BET, CO chemisorption, XRD and XPS techniques. Results showed that the presence of Ce significantly increased the activity and thermal stability of the Pd-Pt/Al₂O₃ catalyst towards methane combustion, which could be attributed to more highly-dispersed active PdO particles over the Pd-Pt/Ce/Al₂O₃ catalyst surface as well as the retarded sintering of PdO and the maintained oxidized state of surface Pd during the combustion process in the presence of Ce.     

不同硅铝比Fe-ZSM-5催化剂对氧化亚氮催化分解性能的研究

以不同硅铝比的H-ZSM-5分子筛为载体,采用离子交换法和化学气相沉积法制备Fe-ZSM-5催化剂,并用XRD、BET、TEM、UV-vis和NH3-TPD等表征手段对催化剂进行分析,研究催化剂中铁的存在状态.结果表明,分子筛的硅铝比影响铁在分子筛中的分布形态,化学气相沉积法和热离子交换法制得硅铝比为25的Fe-ZSM-5-25分子筛催化剂上均匀地分布着粒径为8 nm左右的纳米氧化铁颗粒,并且Fe-ZSM-5-25分子筛催化剂比Fe-ZSM-5-300更容易形成Fe3+x O y团簇.制得的Fe-ZSM-5分子筛催化剂催化分解氧化亚氮(N2O),结果表明,相同的制备方法,硅铝比小的Fe-ZSM-5-25催化剂对N2O分解活性更好;相同硅铝比的Fe-ZSM-5催化剂,采用化学气相沉积法制得的对N2O分解活性最好.另外,O2的存在对Fe-ZSM-5上N2O催化分解活性有抑制作用,而NO对N2O催化分解活性展示了一定的正效应.最后,经过100 h的连续反应,Fe-ZSM-5催化剂依然能够保持催化活性.     

Integrated removal of NO and mercury from coal combustion flue gas using manganese oxides supported on TiO2

A catalyst composed of manganese oxides supported on titania(MnO_x/TiO_2) synthesized by a sol–gel method was selected to remove nitric oxide and mercury jointly at a relatively low temperature in simulated flue gas from coal-fired power plants. The physico-chemical characteristics of catalysts were investigated by X-ray fluorescence(XRF), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS) analyses, etc. The effects of Mn loading,reaction temperature and individual flue gas components on denitration and Hg~0 removal were examined. The results indicated that the optimal Mn/Ti molar ratio was 0.8 and the best working temperature was 240°C for NO conversion. O_2 and a proper ratio of [NH_3]/[NO]are essential for the denitration reaction. Both NO conversion and Hg~0 removal efficiency could reach more than 80% when NO and Hg~0 were removed simultaneously using Mn0.8 Tiat 240°C.Hg~0 removal efficiency slightly declined as the Mn content increased in the catalysts. The reaction temperature had no significant effect on Hg~0 removal efficiency. O_2 and HCl had a promotional effect on Hg~0 removal. SO2 and NH_3were observed to weaken Hg~0 removal because of competitive adsorption. NO first facilitated Hg~0 removal and then had an inhibiting effect as NO concentration increased without O_2, and it exhibited weak inhibition of Hg~0 removal efficiency in the presence of O_2. The oxidation of Hg~0 on Mn O x/TiO_2 follows the Mars–Maessen and Langmuir–Hinshelwood mechanisms.