BDD电极阳极氧化垃圾渗滤液纳滤浓缩液

实验研究了电化学技术阳极氧化垃圾渗滤液纳滤浓缩液,比较了不同阳极种类、电流密度和极板间距对污染物降解的影响。结果表明,掺硼金刚石(boron-doped diamond,BDD)薄膜电极作为阳极,比钛基镀钌铱(Ti-RuO2-IrO2)和钛基镀铂(Ti-Pt)电极作为阳极时,有机物的矿化更为迅速。选用BDD电极作为阳极,不锈钢电极作为阴极,随着电流密度的增加(10~100 mA/cm2),TOC去除率随之提高,极板间距的改变(2~12 mm)对TOC的降解影响较小。BDD阳极氧化6 h后,浓缩液的TOC去除率达到94%。研究表明,BDD电极阳极氧化技术可有效地处理垃圾渗滤液纳滤浓缩液,可将其应用于高毒性难生物降解的有机废水的处理工艺中。     

电化学阴极活化掺硼金刚石膜电极

掺硼金刚石膜(BDD)电极是一种理想的用于电化学分析微量重金属离子的非汞电极,选择合适的BDD电极类型和探索简便的活化BDD电极的方法对提高其电分析检测能力和延长其使用寿命具有重要意义。本研究考察了3种硅基掺硼浓度(B原子浓度分别为2×1020/cm3、8×1020/cm3和27×1020/cm3,简写为BDD-2、BDD-8和BDD-27)的BDD电极经历相同的阴极预处理:在0.5 mol/L H2SO4溶液中,阴极恒电位(-3V vs.饱和甘汞电极)极化5、10、20、30和50 min后,以铁氰化钾/亚铁氰化钾为氧化还原探针,用交流阻抗和循环伏安技术表征了阴极极化后的BDD电极的电化学活性,并用阳极溶出伏安法,通过对一系列已知浓度的铅离子的测量试评估了阴极活化的效果。结果表明,电化学阴极预处理能显著提高3种掺硼浓度的BDD电极的表面活性,但阴极活化效果与BDD的掺硼浓度和阴极预处理时间有关,BDD-27和BDD-8的最佳阴极预处理时间分别为30 min和10 min,BDD-2因表面活性太差并不适合用于电分析。     

掺硼金刚石/Si-Ti电极体系处理沙坦类制药生化尾水溶解性有机物的研究

沙坦类制药废水经生化处理后的外排尾水仍残留有溶解性有机物(DOM),需要深度处理。掺硼金刚石(BDD)薄膜类形稳电极是水处理领域的主要材料。剖析了沙坦类制药生化尾水的荧光特征,评估了BDD/Si-Ti电极体系深度处理沙坦类制药生化尾水DOM的性能。结果表明：沙坦类制药生化尾水有2种独立荧光组分,其中色氨酸组分(中心激发波长=250 nm,中心发射波长=350 nm)是特征荧光组分;BDD/Si-Ti电极体系深度处理沙坦类制药生化尾水的经济电流密度为10～15 mA/cm²。傅立叶变换红外光谱(FT-IR)分析显示,共轭有机物及共轭基团是此类尾水荧光的主要来源,共轭结构被BDD/Si-Ti电极体系有效分解,生成烷烃类物质,因此电解60 min后荧光基本消失。     

Ti/BDD/PbO_2复合电极在化学需氧量测定中的应用

以钛基掺硼金刚石为基体,采用电沉积的方法制备了Ti/BDD/PbO2复合电极,并将其用于化学需氧量（COD）的测定。采用扫描电子显微镜（SEM）和X射线衍射谱图（XRD）表征了电极的微观形貌及结构,采用电化学工作站考察了电极对有机物响应特性。实验结果表明,在1.45 V的低电位条件下,线性范围为0.5～175 mg/L,检测限为0.3 mg/L（S/N=3）。采用Ti/BDD/PbO2复合电极测定法和重铬酸钾标准方法对市政污水、食品废水及印染废水的对比结果表明,2种方法的相对误差小于10%,具有良好的一致性。     

运用BDD电极优化废水中氨氮的直接电化学检测方法

针对高氨氮条件下离子选择电极稳定性差的问题,筛选了3种市售硼掺杂金刚石(BDD)电极,以探究直接电化学检测氨氮的可行性.采用极化曲线法测试了3种BDD电极的析氧、析氢和析氯电位,以获得最佳电势窗口.采用循环伏安法研究了氨氮在3种BDD电极上的氧化还原行为,在1.6 V处发现了明显的氨氮氧化峰,可为氨氮直接检测提供定性依据.通过控制变量法优化了方波伏安法(SWV)和差分脉冲伏安法两种扫描方式的测试参数.结果表明,SWV响应电流更高.最佳测试参数为:方波频率10 Hz,阶跃电位2 mV,脉冲幅度50mV.在最佳条件下,当氨氮浓度为1～18mmol·L-1时,发现两段线性范围,最低检测限为0.283 mmol·L-1.本研究所建立的测试方法响应时间短、线性范围宽、稳定性强,并成功应用于垃圾渗滤液中氨氮的测定.     

Ti/BDD/PbO2复合电极在化学需氧量测定中的应用

以钛基掺硼金刚石为基体,采用电沉积的方法制备了Ti/BDD/PbO2复合电极,并将其用于化学需氧量(COD)的测定。采用扫描电子显微镜(SEM)和X射线衍射谱图(XRD)表征了电极的微观形貌及结构,采用电化学工作站考察了电极对有机物响应特性。实验结果表明,在1.45 V的低电位条件下,线性范围为0.5～175 mg/L,检测限为0.3 mg/L(S/N=3)。采用Ti/BDD/PbO2复合电极测定法和重铬酸钾标准方法对市政污水、食品废水及印染废水的对比结果表明,2种方法的相对误差小于10%,具有良好的一致性。     

氯自由基介导的BDD电极选择性氧化脱氮

为实现氨氮的高效选择性转化,设计了一个氯自由基介导的电化学体系。该电化学体系以稳定性好、氧化能力强的掺硼金刚石(BDD)电极为阳极,以Pd-Cu修饰的泡沫镍材料(Pd-Cu/NF)为阴极,以氯化钠为电解质,对BDD电极选择性电催化氧化性能与机理进行了研究。结果表明:在4.0 V电压下,体系中的Cl~-原位可转NO_3~-,副产物N_2;分别探究了阴极材料、电场强度、电极间距、溶液pH和电解质种类对氨氮转化性能的影响。通过电子顺磁共振和自由基捕获实验,证实了Cl·在氨氮转化过程中发挥了重要作用。在最优条件下,可实现40 min内100%的氨氮转化率和25 mg·L~(-1)的N_2生成量,以上研究结果可为解决水体中氨氮的污染问题提供参考。     

碱改性活性炭纤维电吸附处理RO浓水效果及除盐动力学特性

针对电吸附技术在反渗透浓水回收利用过程中的吸附效率问题,通过NaOH、KOH、氨水对ACF电极材料进行浸渍改性,采用SEM观察、傅里叶变换红外光谱图分析的方法对改性前后ACF进行了表征;研究了改性前后ACF对反渗透浓水的去除效果和除盐动力学特性;探讨了碱改性前后ACF处理反渗透浓水的除盐机理。结果表明:随着氨水改性ACF比表面积的增加,表面碱性基团增加、酸性基团减少;ACF理化特征的变化与改性剂溶液的酸碱性有关;氨水改性ACF对反渗透浓水中电导率、氨氮、COD均有很好的降低或去除效果,而NaOH改性ACF对UV_(254)有很好的去除效果;碱改性ACF处理反渗透浓水除盐过程更符合Elovich动力学方程;碱改性ACF电吸附处理反渗透浓水时,对各污染物指标表现出选择性,且与未改性ACF相比,具有更好的降低或去除效果,同时,碱改性ACF电吸附除盐过程是以物理吸附和化学吸附共存的多相吸附过程,也会存在离子交换作用。     

新型二氧化铅电极处理有机染料废水的研究

研究了高压塑片法制备新型二氧化铅电极的工艺,通过循环伏安、X衍射和扫描电镜等手段对电极性能的考察表明,该电极不仅具有高电催化活性,还有很好的抗腐蚀性能.通过与普通石墨电极的对比实验,进一步探讨了该电极降解中性枣红染料的机制和工艺条件.结果表明,该电极在脱色和COD降解方面都有明显的优越性.在含磷酸盐和氯离子的体系中,降解效率尤为突出.     

新型二氧化铅电极处理有机染料废水的研究

研究了高压塑片法制备新型二氧化铅电极的工艺,通过循环伏安、X衍射和扫描电镜等手段对电极性能的考察表明,该电极不仅具有高电催化活性,还有很好的抗腐蚀性能.通过与普通石墨电极的对比实验,进一步探讨了该电极降解中性枣红染料的机制和工艺条件.结果表明,该电极在脱色和COD降解方面都有明显的优越性.在含磷酸盐和氯离子的体系中,降解效率尤为突出.     

Novel hybrid composite discharge electrode for electrostatic precipitator

Over the last few decades, electrostatic precipitators (ESPs) have emerged as effective air pollution control devices for treating coal-fired power plant exhausts. Among the components of the ESP, the discharge electrodes are extremely important in determining the collection efficiency of the ESP. Typically, in wet ESPs, the discharge electrodes used must be made of corrosion-resistant alloys, which makes them extremely expensive and heavy. Hybrid composite discharge electrodes have the potential to be lightweight and corrosion-resistant substitute for traditional metal alloy electrodes used in wet ESPs. In this experimental study, a novel hybrid composite electrode (recently patented at Ohio University) is presented as a substitute for traditional metal electrodes in wet ESPs. The samples of hybrid electrodes were fabricated by using carbon fiber composites, combined with metal mesh, in the shape of a long and thin tape. The electrode’s electrical response was evaluated in open atmospheric conditions, while connected to a transformer-rectifier unit to generate a corona current at voltages exceeding 50 kV. Results of these hybrid electrodes were compared with traditional metal electrodes. The hybrid composite discharge electrode produced a uniform corona at comparable power levels to that of metal electrodes, with additional advantages of being compact, lightweight, and highly corrosion resistant. In addition, hybrid composite electrodes exhibited lower corona onset voltage as compared with metal electrodes. The preliminary experimental data are encouraging and show significant potential for this new inexpensive hybrid electrode to replace metal electrodes in wet ESPs, providing comparable (and in some cases exceeding) collection efficiencies with lower ozone generation.

Implications: The newly invented hybrid composite electrode (HCE) performance was evaluated through experimentation with conventional metal electrodes. The HCE performance was comparable to the metal electrodes. The HCE also exhibited uniform corona fields and steady power while maintaining similar and in some cases superior electrical performance as compared with metal electrodes and thus shows a significant potential to substitute metal electrodes in wet ESP systems.     

Effect of Relative Humidity on Electrically Stimulated Filter Performance

This work investigates the effect of relative humidity (RH) on the performance of three electrically stimulated filter designs, with and without prechargers. Two different filter media were used: cellulose paper (relatively conductive) and fiberglass paper (relatively nonconductive). Designs with electrodes contacting either of the two filter media are shown to draw currents, exponentially increasing with RH. In contrast, a noncontacting, air gap, electrode design has been shown to be significantly less sensitive to RH. Further, the air gap or noncontacting electrode behaves differently than insulated electrodes. The noncontacting electrode does not exhibit the polarizing or field cancelling effect of insulated (coated) electrodes. This is probably due to a small but finite amount of ionization at the sharp electrode perforations.     

Evaluation of the electrochemical behavior of pentachlorophenol by cyclic voltammetry on carbon paste electrode modified by humic acids.

Humic substances, or natural recalcitrant organic matter, have an important role in the environment for their plant nutritional functions or for their capability to control the mobility of xenobiotic substances, such as pesticides. To verify the electrochemical behavior of pentachlorophenol (PCP), cyclic voltammetry was used because of its versatility. The following two different electrodes were used: carbon paste electrode (CPE) and carbon paste electrode chemically modified with humic acid (HACMCPE). The results demonstrated that PCP was better accumulated at the HACMCPE electrode, as a consequence of a larger current signal than at the CPE electrode. Cyclic voltammograms showed oxidation steps of PCP itself and probable production of quinonelike compounds.     

有毒难降解有机物高级氧化电催化电极

在电催化电极的作用下 ,电化学反应和化学催化作用结合 ,导致有机分子的电催化降解。在分析中 ,综述了电催化高级氧化电极研究现状 ,阐述与评价了过渡金属涂层电极、金属氧化物涂层电极、含掺杂半导体涂层电极、金刚石膜电极、三维电极等几个主要方面的研究成果 ,并对今后工作的重点提出了一些意见。     

Ce-PbO_2/C电极的制备及其去除水中酸性红B

采用电沉积法制备铈修饰的PbO2/C电极,通过SEM、XRD、XPS及循环伏安对PbO2/C、Ce-PbO2/C电极进行表征,结果表明,Ce-PbO2/C电极比PbO2/C颗粒细小,表面均匀致密,电化学氧化能力较强,修饰电极中Ce以CeO2的形态存在。以Ce-PbO2/C为工作电极,电解浓度为1 000 mg/L的高盐酸性红B模拟活性染料废水,考察了电压、pH、电解质浓度、极间距对脱色率、氨氮去除率及COD去除率的影响。确定适宜工艺条件为：初始酸性红B溶液浓度为1 000 mg/L,pH值为6,电压10 V,电解时间1 h,电极间距1.5 cm,该条件下脱色率、氨氮去除率和COD去除率分别为99.98%、97.23%和90.17%。通过UV-Vis及GC-MS初步分析了降解过程可能存在的中间产物及降解途径。     

平板炭气凝胶电极电吸附除氟

采用自制的炭气凝胶平板电极进行模拟水样中氟的电吸附去除研究,通过单因子实验优化了该电吸附技术的操作参数和适用的溶液条件,并研究了反接电极法的再生效果。研究结果表明,自制的炭气凝胶平板由纳米颗粒组成三维网络结构,比表面积为670.90 m2/g,具有良好的充放电可逆性和迅速形成表面双电层的特点。静态电吸附除氟效果最佳的条件为:水样氟离子浓度6 mg/L,pH 7.0,极板间距4 cm,电压1.6 V;共存物质硝酸根、腐殖酸、碳酸根和碳酸氢根等对氟离子的电吸附具有一定的促进作用。吸附氟离子后的炭气凝胶材料的比表面、孔体积、电容值有所减小。对于吸附氟离子后的炭气凝胶平板电极,采用反接电极法取得较好再生效果的条件为:流动状态、电压1.6 V、极板间距4 cm。再生后的炭气凝胶电极与原始炭气凝胶相比,依然具有良好的充放电可逆性。     

An evaluation of electrode insertion techniques for measurement of redox potential in estuarine sediments

E(h) measurements by electrodes are commonly used to characterize redox status of sediments in freshwater, marine and estuarine studies, due to the relative ease and rapidity of data collection. In our studies of fine-grained estuarine seabeds, we observed that E(h) values measured in intact sediment cores were influenced by different electrode insertion techniques. Sediment E(h) measurements generated via lateral insertion of platinum electrodes through silicone-filled ports in acrylic cores were systematically more positive (on the order of 10-100 mV) than profiles generated via vertical insertion of platinum electrodes downward through the sediment-water interface of the same cores. A review of the literature indicated that while researchers routinely use both insertion techniques to measure E(h), no discrepancy in output has previously been reported. We discuss the results of three experiments conducted to determine if the discrepancy in output was caused by electrode poisoning by sulfides during the stepwise vertical insertion technique, or was caused by contact of the electrode with the silicone plug during the lateral insertion technique. We conclude that contact between the platinum surface of the electrode and the silicone plug biases the E(h) measurements, resulting in erroneously positive E(h) values. Insertion of electrodes into sediment through silicone plugs produced E(h) values that were an average of 105.6 mV (+/-10.4 SE) more positive than values generated upon electrode insertion directly into sediment. Thus, we recommend against using an insertion technique where the platinum electrode remains in contact with the silicone plug, as this method results in misclassification of sediment redox state and estimated depth of the redoxcline.     

Ce-PbO2/C电极的制备及其去除水中酸性红B

采用电沉积法制备铈修饰的PbO2/C电极,通过SEM、XRD、XPS及循环伏安对PbO2/C、Ce-PbO2/C电极进行表征,结果表明,Ce-PbO2/C电极比PbO2/C颗粒细小,表面均匀致密,电化学氧化能力较强,修饰电极中Ce以CeO2的形态存在。以Ce-PbO2/C为工作电极,电解浓度为1 000 mg/L的高盐酸性红B模拟活性染料废水,考察了电压、pH、电解质浓度、极间距对脱色率、氨氮去除率及COD去除率的影响。确定适宜工艺条件为:初始酸性红B溶液浓度为1 000 mg/L,pH值为6,电压10 V,电解时间1 h,电极间距1.5 cm,该条件下脱色率、氨氮去除率和COD去除率分别为99.98%、97.23%和90.17%。通过UV-Vis及GC-MS初步分析了降解过程可能存在的中间产物及降解途径。     

阴极氧还原产电生物可渗透反应栅的研究Ⅱ.酸蚀处理对不锈钢丝电极性能的影响

不锈钢毛虽然用作阴极氧还原产电生物反应栅（CORE—PRB）的电极材料虽然有很多优点，但是反应电流较小。尝试对不锈钢毛进行酸蚀处理后用作电极材料，并分别研究比较了4种不同电极组合的产电反应性能。酸蚀处理显著提高不锈钢毛阳极的反应性能，并对提高不锈钢毛阴极的反应性能有一定作用。酸蚀的作用主要是使不锈钢毛表面变得粗糙，有利于提高电极表面积和材料的生物亲和性。虽然生物产电反应对COD降解的直接贡献不到10％，但是不同电极组合下COD的去除率与它们生物产电反应的贡献率呈现高度正相关性。     

Electrocatalytic reduction of nitrate in water with a palladium-modified copper electrode.

A highly active electrocatalytic electrode for nitrate reduction was prepared by the electro-deposition of palladium onto a copper electrode. The capacity of nitrate reduction by a palladium-modified copper electrode has been studied using cyclic voltammetry (CV). The existence of a reduction peak at -0.605 V versus saturated calomel electrode in 0.1-M sodium nitrate + 0.1-M perchloric acid solution (pH = 0.86) can be found in the CV measurement. The influence of solution properties, such as pH, nitrate concentration, and other anions in solution, on nitrate reduction was determined in detail. Results showed that nitrate reduction was suppressed in alkaline solution, while it was beneficial to nitrate reduction in acid or neutral solution. At low nitrate concentrations (0.01 to 0.5 M), nitrate reduction current increased with increasing nitrate concentration, but was hindered by sulfate. At high nitrate concentrations (1 to 5 M), no significant difference on nitrate reduction was observed. Compared with other different electrodes prepared in our work (copper, titanium, and palladium-modified titanium electrodes), the palladium-modified copper electrode showed the highest electrocatalytic capacity and stability in the nitrate-reduction process.