When solids meet solids: A glimpse into dust mixture explosions

Mixing an inert solid or a less flammable compound with a combustible dust can be regarded as a direct application of the inherent safety principle of moderation. An experimental investigation was carried out to determine the evolution of the ignition sensitivity and the explosion severity of such various mixtures as a function of their compositions. It demonstrates that the introduction of small amounts of highly combustible powders (such as sulphur or nicotinic acid) to a less flammable dust (such as microcrystalline cellulose or carbon black) can strongly influence the ignition sensitivity as well as the explosion severity.It has notably been shown that the ignition sensitivity of solid/solid mixtures significantly rises up when only 10–5%wt. of highly flammable dust is introduced. Simple models can often be applied to estimate the minimum ignition energy, minimum ignition temperature and minimum explosive concentration of such mixtures. Concerning the dust explosivity, three cases have been studied: mixtures of combustibles dusts without reaction, dusts with reactions between the powders, combustible dusts with inert solid. If the evolution of the maximum explosion pressure can be estimated by using thermodynamic calculations, the maximum rate of pressure rise is more difficult to predict with simple models, and both combustion kinetics and hydrodynamics of the dust clouds should be taken into account. These results were also extended to flammable dust/solid inertant mixture. They clearly show that the concentration of solid inertant at which the ignition is not observed anymore could reach 95%wt. As a consequence, the common recommendation of solid inertant introduction up to 50–80%wt. to prevent dust explosion/ignition should be reconsidered.     

湍流对粉尘云电火花点火过程的影响

随着现代工业的发展，粉尘爆炸事故发生的频率也逐年增加，因此，对粉尘云点火敏感程度进行测量和计算就变得十分重要。粉尘云最小点火能是粉尘爆炸重要的特性参数之一，是采取粉尘爆炸防护的基础。最小点火能在测量的过程中受到多个敏感条件的影响，其中湍流则是最复杂的影响因素之一。文中对实验过程中粉尘云的湍流进行了定义，并分析了湍流对粉尘云最小点火能影响的内在原因；同时对通过数值模拟计算粉尘云最小点火能过程中的湍流计算给出了数学模型。从实验和数学模型两个方向对湍流进行了全面描述，对粉尘云电火花点火过程中湍流影响的分析结论，可有效的指导实验。     

Study of dust cloud behaviour in the modified Hartmann tube using the image subtraction method (ISM)

A dispersion of fine particles in the air is needed for a dust explosion to occur since an explosion is the fast combustion of particles in the air. When particles are poorly dispersed, agglomerated, or their concentration is low, the combustion velocity decreases, and deflagration would not occur. The combustion rate is strictly related to dust concentration. Therefore, the maximum explosion pressure rise occurs at dust concentration close to stoichiometric. Conversely, Minimum Explosion Concentration (MEC) is the lower limit at which self-sustained combustion and a pressure rise are possible. Dust explosion tests are designed to reproduce the dispersion and generation of dust clouds in industrial ambiences by using dispersion devices activated by pressurised air pulses. The resulting dust cloud, which has a marked transient character, is considered representative of real clouds by current standards. Over time, several studies have been carried out to optimise these devices (e.g. to reduce the inhomogeneity of the cloud in the 20 L sphere). The Minimum Ignition Energy (MIE) of dust is measured using the Mike3 modified Hartmann tube, where the ignition attempt is made 60–180 ms after dust dispersion regardless of dust characteristics.This work investigates the dust clouds’ actual behaviour inside the modified Hartmann tube before ignition using high-velocity video movies and a new image post-treatment method called Image Subtraction Method (ISM). Movies are recorded with high-speed cameras at a framerate of 2000 fps and elaborated with an on-purpose developed LabVIEW® code. Concentration (mass per volume) and dispersion pressure are varied to evaluate their effect on dust clouds. Maise starch, iron powder and silica powder are chosen to investigate the effect of particle density and size on the cloud structure and turbulence. This approach will help to investigate the structure of the dust cloud, the shape and size of the particle lumps and the change in dust concentration over time. In addition, information on the actual concentration and cloud turbulence at the ignition location and delay time were obtained, which may help identify the local turbulence scale and widen the characterisation of the cloud generated in the Hartmann tube.     

基于20 L球罐的多相混合物扩散模拟

为更好地探索多相混合物的爆炸特性，以铝粉、乙醚、空气为研究对象，基于20 L球型爆炸罐建立三维计算模型，对气固两相和气液固三相混合物的分散过程进行数值模拟，以分析不同多相混合物分散过程的差异，并为测量多相混合物爆炸下限时的点火延迟时间设定提供参考。监测分析铝粉浓度粒子分布、流场内部湍流动能以及液相体积百分数等的演化过程，讨论混合物分散效果的差异，并确定测量爆炸下限的点火延迟时间。研究结果表明:实验工况下，液相的存在会降低粉尘云团的湍流动能、降低其扩散速度，并使粉尘云内部浓度更均匀。测量多相混合物爆炸下限时，三相混合物的最佳点火延迟时间早于气固两相混合物10~20 ms。     

A numerical model for the prediction of the minimum ignition temperature of dust clouds

This paper presents a numerical model for the prediction of the minimum ignition temperature (MIT) of dust clouds. First, a physical model is developed for the dust cloud ignition in the Godbert-Greenwald furnace. A numerical approach is then applied for the MIT prediction based on the physical model. The model considers heat transfer between the air and dust particles, the dust particle reaction kinetics, and the residence times of dust clouds in the furnace. In general, for the 13 dusts studied, the calculated MIT data are in agreement with the experimental values. There is also great accordance between the experimental and numerical MIT variation trends against particle size. Two different ignition modes are discovered. The first one consists in ignition near the furnace wall for bigger particles characterized by rather short residence times. In the second mode, the ignition starts from the center of the furnace by self-heating of the dust cloud for smaller particles with longer residence times. For magnesium, as dust concentration increases, the lowest ignition temperature of the dust cloud IT(conc) decreases first, then transits to increase at a certain point. The transition happens at different dust concentrations for different particle sizes. Moreover, the MIT of the magnesium dust cloud generally increases as particle size increases, but the increasing trend stagnates within a certain medium particle size range.     

A constant pressure dust explosion experiment

A new apparatus has been designed for investigating flame propagation in turbulent dust clouds at near constant pressure conditions. The experimental approach is inspired by the classical soap bubble method for measuring burning velocities in gaseous mixtures. Combustible dust is dispersed with pressurised air to form an explosive mixture inside a transparent latex balloon. After a certain delay time, the turbulent dust cloud is ignited by a 40 J chemical igniter. A digital high-speed video camera records the propagating flame and the expansion of the balloon. Experiments were performed with two types of dust, Lycopódium spores and maize starch, as well as with propane–air mixtures under initially quiescent or turbulent conditions. Although the results are primarily qualitative in nature, they nevertheless demonstrate fundamental differences between premixed combustion of gaseous mixtures, and ‘premixed combustion with non-premixed substructures' in mechanical suspensions of solid particles dispersed in air. The discussion highlights some fundamental challenges for future dust explosion research.     

Study of the severity of hybrid mixture explosions and comparison to pure dust-air and vapour-air explosions

The explosion behaviour of heterogeneous/homogeneous fuel-air (hybrid) mixtures is here analysed and compared to the explosion features of heterogeneous fuel-air and homogeneous fuel-air mixtures separately.Experiments are performed to measure the pressure history, deflagration index and flammability limits of nicotinic acid/acetone-air mixtures in a standard 20 L Siwek bomb adapted to vapour-air mixtures. Literature data are also used for comparison.The explosion tests performed on gas-air mixtures in the same conditions as explosion tests of dust-air mixtures, show that the increase in explosion severity of dust/gas-air mixtures has to be addressed to the role of initial level of turbulence prior to ignition.At a fixed value of the equivalence ratio, by substituting the dust to the flammable gas in a dust/gas-air mixture the explosion severity decreases. Furthermore, the most severe conditions of dust-gas/air mixtures is found during explosion of gas-air mixture at stoichiometric concentration.     

Does the dust explosion risk increase when moving from μm-particle powders to powders of nm-particles?

Based on experience with powders of particle sizes down to the 1–0.1 μm range one might expect that dust clouds from combustible nm-particle powders would exhibit extreme ignition sensitivities (very low MIEs) and extreme explosion rates (very high K_St-values). However, there are two basic physical reasons why this may not be the case. Firstly, complete transformation of bulk powders consisting of nm-particles into dust clouds consisting of well-dispersed primary particles is extremely difficult to accomplish, due to very strong inter-particle cohesion forces. Secondly, should perfect dispersion nevertheless be achieved, the extremely fast coagulation process in clouds of explosive mass concentrations would transform the primary nm-particles into much larger agglomerates within fractions of a second. Furthermore, for organic dusts and coal the basic mechanism of flame propagation in dust clouds suggests that increased cloud explosion rates would not be expected as the particle size decreases into the <1 μm range. An overall conclusion is that dust clouds consisting of nm primary particles are not expected to exhibit more severe K_St-values than clouds of μm primary particles, in agreement with recent experimental evidence. In the case of the ignition sensitivity recently published evidence indicates that MIEs of clouds in air of some metal powders are significantly lower for nm particles than for μm particles. A possible reason for this is indicated in the paper.     

初始温度对湿法成型硫磺燃烧爆炸特性影响的试验研究

为了研究初始温度变化对湿法成型硫磺粉尘燃烧爆炸特性的影响,通过对初始温度分别为35℃、 45℃、 55℃、 65℃、 75℃的硫磺粉尘试样进行测试,发现随着初始温度的上升硫磺粉尘的粉尘云最低着火温度,粉尘云最小点火能逐渐降低;随着初始温度的上升硫磺粉尘的爆炸下限和粉尘层最低着火温度不发生变化。随着温度的升高,硫磺粉尘的燃烧爆炸危险性增加,因此在气温较高的夏秋季节要提高硫磺粉尘燃爆的防护等级。     

Influence of different ignition delay times on the pressure rise rate in hybrid mixture explosions in the 20-L sphere

For the development of a standardized method for measuring the explosion safety characteristics of combustible hybrid dust/vapor mixtures, the influence of the ignition delay time needs to be investigated. The ignition delay time, defined as the time between the injection of dust and the activation of the ignition source, is related to the turbulence of the mixture and thus to the pressure rise rate. The ignition source for pure vapors, however, has to be activated in a quiescent atmosphere according to the standards. Nevertheless, when measuring the explosion safety characteristics of hybrid mixtures, it is important that the dust be in suspension around the igniter. Like pure dust/air mixtures, hybrid dust/vapor/air mixtures need to be ignited in a turbulent atmosphere to keep the dust in suspension.This work will therefore investigate the influence of ignition delay times on the severity of hybrid explosions. It was generally found that at shorter ignition delay times, (dp/dt)_ex increased due to higher turbulence and decreases as the dust sinks to the bottom of the 20 L-sphere. This effect is more pronounced for hybrid mixtures with higher vapor content compared to dust content.     

Differences and similarities of gas and dust explosions: A critical evaluation of the European ‘ATEX’ directives in relation to dusts

Explosive gas mixtures and explosive dust clouds, once existing, exhibit similar ignition and combustion features. However, there are two basic differences between dusts and gases which are of substantially greater significance in design of safety standards than these similarities. Firstly, the physics of generation and up-keeping of dust clouds and premixed gas/vapour clouds are substantially different. This means that in most situations where accidental explosive gas clouds may be produced quite readily, generation of explosive dust clouds would be highly unlikely. Secondly, contrary to premixed gas flame propagation, the propagation of flames in dust/air mixtures is not limited only to the flammable dust concentration range of dynamic clouds. The state of stagnant layers/deposits offers an additional discrete possibility of flame propagation.

The two European Directives 94/9/EC (1994) and 1999/92/EC (1999) primarily address gases/vapours, whereas the particular properties of dusts are not addressed adequately. Some recent IEC and European dust standards resulting from this deficiency are discussed, and the need for revising the two directives accordingly is emphasized.     

Validation of a new formula for predicting the lower flammability limit of hybrid mixtures

A correlation of the lower flammability limit for hybrid mixtures was recently proposed by us. The experimental conditions including ignition energy and turbulence which play a primary role in a gas or dust explosion were at fixed values. The sensitivity of such experimental conditions to the accuracy of the proposed formula was not thoroughly discussed in the previous work. Therefore, this work studied the effect of varying the ignition energy and turbulence intensity to the formula proposed in our previous paper. For ignition energy effect, results from methane/niacin mixture demonstrated that the MEC and LFL will not be affected by changing ignition energy. There is no distinguishable difference among gas explosion index (K_G) and dust explosion index (K_St) derived from tests with every ignition energy (2.5 kJ, 5 kJ and 10 kJ) in a 36 L vessel. The proposed formula is independent of ignition energy. For turbulence effect, the proposed formula can have a good prediction of the explosion and non-explosion zone if the ignition delay time is within a certain range. The formula prediction is good as the ignition delay time increases up to 100 ms in this work. Propane/niacin and propane/cornstarch mixtures are also tested to validate the proposed formula. It has been confirmed that the proposed formula predicts the explosion and non-explosion zone boundary of such mixtures.     

Minimum ignition energy of mixtures of combustible dusts

Most industrial powder processes handle mixtures of various flammable powders. Consequently, hazard evaluation leads to a reduction of the disaster damage that arises from dust explosions. Determining the minimum ignition energy (MIE) of flammable mixtures is critical for identifying possibility of accidental hazard in industry. The aim of this work is to measure the critical ignition energy of different kinds of pure dusts with various particle sizes as well as mixtures thereof.The results show that even the addition of a modest amount of a highly flammable powder to a less combustible powder has a significant impact on the MIE. The MIE varies considerably when the fraction of the highly flammable powder exceeds 20%. For dust mixtures consisting of combustible dusts, the relationship between the ignition energy of the mixture and the minimum ignition energy of the components follows the so-called harmonic model based upon the volume fraction of the pure dusts in the mixture. This correlation provides results which show satisfactory agreement with the experimental values.     

Experiment-based investigations of magnesium dust explosion characteristics

An experimental investigation was carried out on magnesium dust explosions. Tests of explosion severity, flammability limit and solid inerting were conducted thanks to the Siwek 20 L vessel and influences of dust concentration, particle size, ignition energy, initial pressure and added inertant were taken into account. That magnesium dust is more of an explosion hazard than coal dust is confirmed and quantified by contrastive investigation. The Chinese procedure GB/T 16425 is overly conservative for LEL determination while EN 14034-3 yields realistic LEL data. It is also suggested that 2000-5000 J is the most appropriate ignition energy to use in the LEL determination of magnesium dusts, using the 20 L vessel. It is essential to point out that the overdriving phenomenon usually occurs for carbonaceous and less volatile metal materials is not notable for magnesium dusts. Trends of faster burning velocity and more efficient and adiabatic flame propagation are associated with fuel-rich dust clouds, smaller particles and hyperbaric conditions. Moreover, Inerting effectiveness of CaCO₃ appears to be higher than KCl values on thermodynamics, whereas KCl represents higher effectiveness upon kinetics. Finer inertant shows better inerting effectiveness.     

Explosion temperatures and pressures of metals and other elemental dust clouds

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties—from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly “refractory” elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from 1550 K for tin and tungsten powders to 2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.     

敏感条件对粉尘云最小点火能的影响规律分析

为使粉尘云最小点火能实验测量更准确,从多个方面分析影响最小点火能的测量因素,并根据粉尘云状态、粉尘颗粒固有性质、点火电路等几个方面对影响粉尘云最小点火能的因素,即敏感条件进行了分类。在实验测量中,具体归纳为:粉尘浓度、粉尘湿度、粉尘粒度及其分布、粉尘挥发份含量、粉尘温度(环境温度)、粉尘云的湍流度、粉尘分散质量、粉尘云初始压力、环境氧浓度、电极材料、电极直径和电极末端曲率、电极间距、电火花持续时间、点火延迟时间、电火花能量密度、火花触发电路、可燃气体影响、实验次数等18个影响因素。重点分析了敏感条件对最小点火能的影响规律,从粉尘云点火机理和过程出发,着重分析一些敏感条件对最小点火能影响的内在原因和实质。     

Effects of thermal radiation heat transfer on flame acceleration and transition to detonation in particle-cloud hydrogen flames

The current work examines regimes of the hydrogen–oxygen flame propagation and ignition of mixtures heated by radiation emitted from the flame. The gaseous phase is assumed to be transparent for the radiation, while the suspended particles of the dust cloud ahead of the flame absorb and reemit the radiation. The radiant heat absorbed by the particles is then lost by conduction to the surrounding unreacted gaseous phase so that the gas phase temperature lags that of the particles. The direct numerical simulations solve the full system of two phase gas dynamic time-dependent equations with a detailed chemical kinetics for a plane flames propagating through a dust cloud. It is shown that depending on the spatial distribution of the dispersed particles and on the value of radiation absorption length the consequence of the radiative preheating of the mixture ahead of the flame can be either the increase of the flame velocity for uniformly dispersed particles or ignition either new deflagration or detonation ahead of the original flame via the Zel'dovich gradient mechanism in the case of a layered particle-gas cloud deposits. In the latter case the ignited combustion regime depends on the radiation absorption length and correspondingly on the steepness of the formed temperature gradient in the preignition zone that can be treated independently of the primary flame. The impact of radiation heat transfer in a particle-laden flame is of paramount importance for better risk assessment and represents a route for understanding of dust explosion origin.     

Ignitability characteristics of aluminium and magnesium dusts that are generated during the shredding of post-consumer wastes

The authors investigated the ignitability of aluminium and magnesium dusts that are generated during the shredding of post-consumer waste. The relations between particle size and the minimum explosive concentration, the minimum ignition energy, the ignition temperature of the dust clouds, etc. the relation between of oxygen concentration and dust explosion, the effect of inert substances on dust explosion, etc. were studied experimentally.

The minimum explosive concentration increased exponentially with particle size. The minimum explosive concentrations of the sample dusts were about 170 g/m³ (aluminium: 0–8 μm) and 90 g/m³ (magnesium: 0–20 μm). The minimum ignition energy tended to increase with particle size. It was about 6 mJ for the aluminium samples and 4 mJ for the magnesium samples. The ignition temperature of dust clouds was about 750 °C for aluminium and about 520 °C for magnesium. The lowest concentrations of oxygen to produce a dust explosion were about 10% for aluminium and about 8% for magnesium. A large mixing ratio (more than about 50%) of calcium oxide or calcium carbonate was necessary to decrease the explosibility of magnesium dust. The experimental data obtained in the present investigation will be useful for evaluating the explosibility of aluminium and magnesium dusts generated in metal recycling operations and thus for enhancing the safety of recycling plants.     

Thermal radiation from vapour cloud explosions

The current study estimates the radiation flux emitted from hot extended gas clouds characteristic of vapour cloud explosions along with the corresponding level of irradiance posed on particles suspended in the unburnt part of the cloud ahead of an advancing flame front. The data presented permits an assessment of the plausibility of combustion initiation by such particles due to forward thermal radiation. The thermal radiation will depend on the emissivity of the burned volume, which relates to the concentration of gaseous and particulate combustion products. A sensitivity analysis has been carried out to account for variations in the equivalence ratio, mixture pressure and radiative heat losses. The spatial distribution of irradiance ahead of the flame front has been computed by introducing appropriate geometrical factors to explore the impact of cloud size. Using fuel rich ethylene-air mixtures it has been shown that high flame emissivities can be achieved at path lengths of order 1 m even in the presence of very low soot volume fractions. The emissivity of gas-soot mixtures will hence be mainly determined by the soot concentration and to a lesser extent by the mixture temperature. Our analysis suggests that the role of forward thermal radiation as a contributing factor to flame propagation in large scale vapour cloud explosions can not currently be ruled out.     

硬脂酸粉着火敏感性影响因素及惰化研究*

为预防和减轻硬脂酸粉加工、储存和运输过程中的燃爆危害,采用Godbert-Greenwald恒温炉分别研究质量浓度、分散压力、惰性粉体质量分数对硬脂酸粉尘云最低着火温度的影响规律。研究结果表明:硬脂酸粉尘云的最低着火温度随质量浓度和分散压力的增加先减小后增大,当质量浓度和分散压力分别为485.4 g/m3,15 kPa时,硬脂酸粉尘云最低着火温度达到最小;添加少量惰性粉体增大了硬脂酸粉尘云分散性,对硬脂酸粉尘云最低着火温度的降低起到促进作用;随惰性粉体质量分数的增加,硬脂酸粉尘云最低着火温度先迅速增大后增速变缓;SiO2通过物理作用抑制硬脂酸粉尘云燃烧,Al(OH)3除物理作用外还通过化学分解参与自由基碰撞,可有效提升硬脂酸粉尘云的最低着火温度。