Waste paper and clinoptilolite as a bulking material with dewatered anaerobically stabilized primary sewage sludge (DASPSS) for compost production

Environmental problems associated with sewage sludge disposal have prompted strict legislative actions over the past few years. At the same time, the upgrading and expansion of wastewater treatment plants have greatly increased the volume of sludge generated. The major limitation of land application of sewage sludge compost is the potential for high heavy metal content in relation to the metal content of the original sludge. Composting of sewage sludge with natural zeolite (clinoptilolite) can enhance its quality and suitability for agricultural use. However, the dewatered anaerobically stabilized primary sewage sludge (DASPSS) contained a low concentration of humic substances (almost 2%), and the addition of the waste paper was necessary in order to produce a good soil conditioner with high concentrations of humics. The final results showed that the compost produced from DASPSS and 40-50% w/w of waste paper was a good soil fertilizer. Finally, in order to estimate the metal leachability of the final compost product, the generalized acid neutralization Capacity (GANC) procedure was used, and it was found that by increasing the leachate pH, the heavy metal concentration decreased. The application of the sequential chemical extraction indicated that metals were bound to the residual fraction characterized as a stabilize fractions.     

Physical and chemical properties study of the activated carbon made from sewage sludge

Preparation of activated carbon from sewage sludge is a promising way to produce a useful adsorbent for pollutants removal as well as to dispose of sewage sludge. The objective of this study was to investigate the physical and chemical properties of the activated carbon made from sewage sludge so as to give a basic understanding of its structure. The activated carbon was prepared by activating anaerobically digested sewage sludge with 5 M ZnCl2 and thereafter pyrolyzing it at 500 degrees C for 2 h under nitrogen atmosphere. The properties investigated in the present study included its surface area and pore size distribution, its elemental composition and ash content, its surface chemistry structure and its surface physical morphology. Furthermore, its adsorption capacities for aqueous phenol and carbontetrachloride were examined. The results indicated that the activated carbon made from sewage sludge had remarkable micropore and mesopore surface areas and notable adsorption capacities for phenol and carbon-tetrachloride. In comparison with commercial activated carbons, it displayed distinctive physical and chemical properties.     

Vitrification as an alternative to landfilling of tannery sewage sludge

Due to high content of heavy metals such as chromium, tannery sewage sludge is a material which is difficult to be biologically treated as it is in the case of organic waste. Consequently, a common practice in managing tannery sewage sludge is landfilling. This poses a potential threat to both soil and water environments and it additionally generates costs of construction of landfills that meet specific environment protection requirements. Vitrification of this kind of sewage sludge with the addition of mineral wastes can represent an alternative to landfilling.The aim of this study was to investigate the possibility of obtaining an environmentally safe product by means of vitrification of tannery sewage sludge from a flotation wastewater treatment process and chemical precipitation in order to address the upcoming issue of dealing with sewage sludge from the tannery industry which will be prohibited to be landfilled in Poland after 2016. The focus was set on determining mixtures of tannery sewage sludge with additives which would result in the lowest possible heavy metal leaching levels and highest hardness rating of the products obtained from their vitrification.The plasma vitrification process was carried out for mixtures with various amounts of additives depending on the type of sewage sludge used. Only the materials of waste character were used as additives.One finding of the study was an optimum content of mineral additives in vitrified mixture of 30% v/v waste molding sands with 20% v/v carbonate flotation waste from the zinc and lead industry for the formulations with flotation sewage sludge, and 45% v/v and 5% v/v, respectively, for precipitation sewage sludge. These combinations allowed for obtaining products with negligible heavy metal leaching levels and hardness similar to commercial glass, which suggests they could be potentially used as construction aggregate substitutes. Incineration of sewage sludge before the vitrification process lead to increased hardness of the vitrificates and reduced leaching of some heavy metals.     

Mechanical properties of dewatered sewage sludge

The mechanical properties of dewatered, anaerobically digested sewage sludge were determined from soil laboratory tests. The sludge material is largely composed of organic clay sized-particles, a sizable fraction of which is in an active state of biological digestion which can continue over many years under field conditions. Moderately digested sludge material was found to have a typical specific gravity of solids value of 1.55, and loss on ignition (LOI) value of 70% dry mass. Strongly digested sludge, produced by digesting the liquid sludge further at 35 degrees C in the laboratory, was found to have a lower LOI value of 55% dry mass, and a higher specific gravity of solids value of about 1.72. The maximum dry density of 0.56 tonne/m3 for the dried sludge material was produced using standard Proctor compaction at roughly 85% moisture content (54% solids content). Air-dried, compacted sludge material was tested in quick-undrained triaxial compression and vane shear. Undrained shear strength-moisture content plots are presented. Shear strength values measured in triaxial compression and vane shear were consistent. The effective angle of shearing resistance (phi') was determined from consolidated-undrained, triaxial compression tests on pasteurized, normally consolidated samples of the sludge material. The mechanical properties of the sludge material changed with the level of sludge digestion. The phi' value increased from 32 degrees for moderately digested sludge, to 37 degrees for strongly digested sludge. The effective cohesion of the sludge material remained zero throughout. The shrinkage, swelling and adhesion properties of the sludge material were also studied. Significant shrinkage occurred as the compacted material dried. The sludge material lost its adhesion below about 95% moisture content (51% solids content). Re-hydration of the dry material caused the bulk volume to double.     

Evaluation of an organic soil amendment generated from municipal solid waste seeded with activated sewage sludge

This study investigated the feasibility of using fresh activated sewage sludge as inoculum for the microbial valorization of segregated municipal solid waste and evaluated the quality of organic soil amendment generated. Organic fraction of municipal solid waste, which consisted of vegetative (vegetable, fruit and flower) wastes was seeded with activated sewage sludge and processed by rapid aerobic microbial treatment. Efficacy of microbial valorization process and quality of final product were assessed by physico-chemical analysis. Suitability of final product was assessed with regard to heavy metal content, pesticide residues, microbiological quality and phytotoxicity. Quality of the soil amendment generated was compared with the control product generated with a commercial microbial inoculum. Phytotoxicity experiments indicated the stimulatory effect of sewage sludge seeded soil amendment on plant growth but inhibition was observed in closed growth test due to the evolution of gaseous phytotoxic agents. The study suggests that segregated municipal solid waste can be effectively valorized with activated non-dewatered sewage sludge as inoculum and the quality of soil amendment generated was comparable to compost intended for unrestricted applications.     

Sewage sludge ash to phosphorus fertiliser (II): Influences of ash and granulate type on heavy metal removal

Ashes from monoincineration of sewage sludge suggest themselves as an ideal base for inorganic fertiliser production due to their relatively high phosphorus (P)-content. However, previously they need to be detoxified by reducing their heavy metal content. The core process considered in this paper consists of three steps: mixing of the ashes with suitable chlorine-containing additives, granulation of the mixture and thermochemical treatment in a rotary kiln. Here relevant heavy metal compounds are first transformed into volatile species with the help of the additives and then evaporated from the granules.In this study two chemically different ashes and their mixture were agglomerated to two different granulate types, briquettes and rolled pellets. The resulting six different materials were subjected to thermal treatment at different temperatures. The heavy metals examined were Cu and Zn due to their strong dependence on treatment conditions and their relevance concerning thermal treatment of sewage sludge ashes. Besides, the behaviour of Cl and K was monitored and evaluated.The experiments showed that ash type and temperature are more influential on Cl and heavy metal chemistry than granulate type. Temperature is a primary variable for controlling removal in both cases. Cu removal was less dependent on both ash and granulate type than Zn. The Cl utilization was more effective for Cu than for Zn. Depending on the treatment conditions some K could be retained, whereas always all P remained in the treated material. This satisfies the requirement for complete P recycling.     

Aerobic thermophilic bacteria enhance biogas production

The enhancing effect of aerobic thermophilic (AT) bacteria on the production of biogas from anaerobically digested sewage sludge (methanogenic sludge) was investigated. Sewage sludge (5%, w/w) was incubated at 65°C with shaking for a few months to prepare the AT seed sludge. AT sludge was prepared by incubation of the AT seed sludge (5%, v/v) and sewage sludge (5%, w/w) at 65°C with shaking. The addition of this AT sludge (1.2% ± 0.5% of total volatile solids) to methanogenic sludge enhanced the production of biogas. The optimum volume of the addition and the pretreatment temperature of the AT sludge for optimum biogas production were 5% (v/v) and 65°C. Batch-fed anaerobic digestion was covered with the addition of various AT sludges. The AT sludge prepared with the AT seed sludge improved the biogas production by 2.2 times relative to that from the sewage sludge addition. The addition of sludge without AT seed sludge weakly enhanced biogas production. An aerobic thermophilic bacterium (strain AT1) was isolated from the AT seed sludge. Strain AT1 grew well in a synthetic medium. The production of biogas from the anaerobic digestion of sewage sludge was improved by the addition of 5% (v/v) AT1 bacterial culture compared with that from the sewage sludge addition. The addition of AT1 culture reduced the volatile solids by 21%, which was higher than the 12.6% achieved with the sewage sludge addition. The AT1 bacterial culture enhanced the biogas production more than the AT seed sludge. The phylogenetic analysis of the 16S rRNA gene revealed that strain AT1 is closely related to Geobacillus thermodenitrificans (100% sequence similarity). The improvement in the production of biogas with the AT sludge could be caused by thermophilic bacterial activity in the AT sludge.     

Application of sewage sludge compost on highway embankments

More and more sewage sludge is being produced in China. Safe and economical methods for sewage sludge disposal should be found considering the increase in sewage treatment. In order to verify the feasibility of sludge disposal on newly built highway embankments, five treatments (0, 15, 30, 60 and 120 tons ha⁻¹) of sewage sludge compost (SSC) were added to a silty-clay embankment soil on the Xi-Huang highway. The results showed that amendment with SSC increased soil available N, available P, organic matter, cation exchange capacity, and water content, and decreased soil bulk density. Application of SSC enhanced ryegrass growth and reduced runoff and soil erosion. Heavy metal losses from sediments in runoff remained constant or decreased relative to the control until a rate of 60 tons ha⁻¹ was exceeded, when heavy metal losses appeared to increase.     

Combining chemical sequential extractions with 3D fluorescence spectroscopy to characterize sludge organic matter

The design and management of anaerobic digestion of sewage sludge (SS) require a relevant characterisation of the sludge organic matter (OM). Methods currently used are time-consuming and often insufficiently informative. A new method combining chemical sequential extractions (CSE) with 3D fluorescence spectroscopy was developed to provide a relevant SS characterisation to assess both OM bioaccessibility and complexity which govern SS biodegradability. CSE fractionates the sludge OM into 5 compartments of decreasing accessibility. First applied on three SS samples with different OM stability, fractionation profiles obtained were in accordance with the latter. 3D fluorescence spectroscopy revealed that the bioaccessible compartments were mainly constituted of simple and easily biodegradable OM while the unaccessible ones were largely made of complex and refractory OM. Then, primary, secondary and anaerobically digested sludge with different biodegradabilities were tested. Complexity revealed by 3D fluorescence spectroscopy was linked with biodegradability and chemical accessibility was correlated with sludge bioaccessibility.     

Thermochemical treatment of sewage sludge ashes for phosphorus recovery

Phosphorus (P) is an essential element for all living organisms and cannot be replaced. Municipal sewage sludge is a carrier of phosphorus, but also contains organic pollutants and heavy metals. A two-step thermal treatment is suggested, including mono-incineration of sewage sludge and subsequent thermochemical treatment of the ashes. Organic pollutants are completely destroyed by mono-incineration. The resulting sewage sludge ashes contain P, but also heavy metals. P in the ashes exhibits low bioavailability, a disadvantage in farming. Therefore, in a second thermochemical step, P is transferred into mineral phases available for plants, and heavy metals are removed as well. The thermochemical treatment was investigated in a laboratory-scale rotary furnace by treating seven different sewage sludge ashes under systematic variation of operational parameters. Heavy metal removal and the increase of the P-bioavailability were the focus of the investigation. The present experimental study shows that these objectives have been achieved with the proposed process. The P-bioavailability was significantly increased due to the formation of new mineral phases such as chlorapatite, farringtonite and stanfieldite during thermochemical treatment.     

Effect of biodegradation on the consolidation properties of a dewatered municipal sewage sludge

The effect of biodegradation on the consolidation characteristics of an anaerobically digested, dewatered municipal sewage sludge was studied. Maintained-load oedometer consolidation tests that included measurement of the pore fluid pressure response were conducted on moderately degraded sludge material and saturated bulk samples that had been stored under static conditions and allowed to anaerobically biodegrade further (simulating what would happen in an actual sewage sludge monofill or lagoon condition). Strongly degraded sludge material was produced after a storage period of 13 years at ambient temperatures of 5-15 degrees C, with the total volatile solids reducing from initially 70% to 55%. The sludge materials were highly compressible, although impermeable for practical purposes. Primary consolidation generally occurred very slowly, which was attributed to the microstructure of the solid phase, the composition and viscosity of the pore fluid, ongoing biodegradation and the high organic contents. The coefficient of primary consolidation values decreased from initially about 0.35m2/yr to 0.003-0.03m2/yr with increasing effective stress (sigmav'=3-100kPa). Initially, the strongly degraded sludge material was slightly more permeable, although both the moderately and strongly degraded materials became impermeable for practical purposes (k=10(-9)-10(-12)m/s) below about 650% and 450% water contents, respectively. Secondary compression became more dominant with increasing effective stress with a mean secondary compression index (Calphae) value of 0.9 measured for both the moderately and strongly degraded materials.     

A feasibility study of thermal hydrolysis by-products as barrier layer materials in the final cover system for a landfill

Most sludge has historically been disposed of in landfills and by ocean dumping but, because of its heavy metal content, this will be totally banned in Korea starting in 2012, based on the London Dumping Convention. Therefore, treatment and disposal methods that are environmentally friendlily are urgently required. The recycling of sewage sludge is a good treatment method for solving sludge problems in an environmentally friendly way. In this study, physical and environmental tests were conducted to evaluate the feasibility of using the by-products of thermal hydrolysis of sewage sludge as barrier layer materials in the final cover systems for landfills. In addition, testing methods for freezing-thawing (KS F 2332) and wetting-drying (KS F 2330) cycles were conducted to assess the effects of cold and hot soil climates starting from pavement. These tests yielded positive results for alternative materials for the barrier layer in a final cover system for a landfill.     

Land application of biosolids. Soil response to different stabilization degree of the treated organic matter

The effect of land application of biosolids on an agricultural soil was studied in a 2-month incubation experiment. The soil microbial biomass and the availability of heavy metals in the soil was monitored after the application of four different composting mixtures of sewage sludge and cotton waste, at different stages of composting. Land application caused an increase of both size and activity of soil microbial biomass that was related to the stabilization degree of the composting mixture. Sewage sludge stabilization through composting reduced the perturbance of the soil microbial biomass. At the end of the experiment, the size and the activity of the soil microbial biomass following the addition of untreated sewage sludge were twice those developed with mature compost. For the mature compost, the soil microbial biomass recovered its original equilibrium status (defined as the specific respiration activity, qCO2) after 18 days of incubation, whereas the soil amended with less stabilized materials did not recover equilibrium even after the two-month incubation period. The stabilization degree of the added materials did not affect the availability of Zn, Ni, Pb, Cu, Cr and Cd in the soil in the low heavy metal content of the sewage sludge studied. Stabilization of organic wastes before soil application is advisable for the lower perturbation of soil equilibria status and the more efficient C mineralization.     

Sequential extraction of metals from mixed and digested sludge from aerobic WWTPs sited in the south of Spain

The content of heavy metals is the major limitation to the application of sewage sludge in soil. However, assessment of the pollution by total metal determination does not reveal the true environmental impact. It is necessary to apply sequential extraction techniques to obtain suitable information about their bioavailability or toxicity. In this paper, sequential extraction of metals from sludge before and after aerobic digestion was applied to sludge from five WWTPs in southern Spain to obtain information about the influence of the digestion treatment in the concentration of the metals. The percentage of each metal as residual, oxidizable, reducible and exchangeable form was calculated. For this purpose, sludge samples were collected from two different points of the plants, namely, sludge from the mixture (primary and secondary sludge) tank (mixed sludge, MS) and the digested-dewatered sludge (final sludge, FS). Heavy metals, Al, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Ti and Zn, were extracted following the sequential extraction scheme proposed by the Standards, Measurements and Testing Programme of the European Commission and determined by inductively-coupled plasma atomic emission spectrometry. The total concentration of heavy metals in the measured sludge samples did not exceed the limits set out by European legislation and were mainly associated with the two less-available fractions (27-28% as oxidizable metal and 44-50% as residual metal). However, metals as Co (64% in MS and 52% in FS samples), Mn (82% in MS and 79% in FS), Ni (32% in MS and 26% in FS) and Zn (79% in MS and 62% in FS) were present at important percentages as available forms. In addition, results showed a clear increase of the concentration of metals after sludge treatment in the proportion of two less-available fractions (oxidizable and residual metal).     

Evaluation of bangkok sewage sludge for possible agricultural use.

Bangkok (Thailand) covers more than 1500 km2 and has 10 million inhabitants. The disposal of wastewater is creating huge problems of pollution. The estimated amount of sewage sludge was estimated to be around 108 tonnes dry matter (DM) per day in 2005. In order to find a lasting way of disposal for this sewage sludge, the suitability of the sludge produced from three waste-water treatment plants for use as fertilizing material was investigated. Monthly samplings and analysis of sewage sludge from each plant showed that the composition of sludge varied according to the area of collection and period of sampling, and there was no link to rainfall cycle. Plant nutrient content was high (i.e. total N from 19 to 38 g kg(-1) DM) whereas organic matter content was low. The concentrations of heavy metals varied between sludge samples, and were sometimes higher than the E.U. or U.S. regulations for sewage sludge use in agriculture. Faecal coliforms were present in the sludge from one of the plants, indicating a possible contamination by night soil. In order to decrease this potentially pathogenic population the sewage sludge should be heated by composting. As the C/N ratio of sewage sludge was low (around 6) some organic by-products with high carbon content could be added as structural material to enhance the composting.     

Leaching characteristics and phytotoxic effects of sewage sludge biochar

Biochar was prepared via the pyrolysis of sewage sludge at temperatures ranging from 300 to 900 °C and the physical–chemical compositions of the biochars obtained were analyzed. Leaching tests were conducted using the biochars to investigate the release of the constituents and their phytotoxic effects on wheat (Triticum aestivum) seeds in a germination test. Multivariate analyses were used to evaluate the contributions of the constituents to the germination index (GI). The results showed that the biochars were rich in micronutrient contents and they improved the germination of wheat. The heavy metal contents were higher in the biochars than the sewage sludge and their levels increased with the pyrolysis temperature, but they were within the acceptable limits for land application, thereby suggesting that sewage sludge is suitable for use as a biochar substrate. The different components of the biochar leachates could promote and inhibit the germination of wheat seeds, where the GI was promoted at lower concentrations but inhibited at higher concentrations. Our results suggest that biochar is an effective and environmentally friendly fixative for the immobilization of heavy metals in sewage sludge when applied to land or disposed of in landfill, but its ecotoxicity needs to be assessed to ensure its environmental safety.     

Effect of compost treatment of sewage sludge on nitrogen behavior in two soils

This work aims to evaluate the effects of compost treatment of digested sewage sludge on nitrogen behavior in two soils, a Spodosol and an Oxisol soil. Digested sewage sludge was composted with sawdust and woodchips, diluting the total nitrogen to one-fourth (dry mass basis) of its original value. Then, sludge and compost were added to the two soils on an equivalent dry weight basis to consider the risk of NO3- -N leaching. Compost treatment of sewage sludge has slowed down the release of mineral-N to half in the Spodosol and to one-third in Oxisol soil. As a result, NO3- -N concentrations in soils incubated with compost were less than half of the amounts found from soils incubated with digested sludge. Estimates were made of the maximum monthly nitrate to leach from the four combinations of soil and sludge treatment. Application of digested sludge, at a higher nitrogen application rate, resulted in a higher nitrate leaching potential than application of the compost product. Soil type also played an important role, with the Oxisol having slightly higher estimated leaching potential than the Spodosol. The higher nitrate release rate in the Oxisol is counterbalanced by its higher field capacity to lessen the expected difference between the two soils.     

Characteristic of heavy metals in biochar derived from sewage sludge

This study investigates the characteristic of heavy metals (Pb, Zn, Cu, Cd, Cr, Ni and As) in biochar derived from sewage sludge at different pyrolysis temperatures (300, 400, 500, 600 and 700 °C). The heavy metal concentrations, chemical speciation distribution, leaching toxicity, and bio-available contents were investigated using ICP-OES after microwave digestion, a sequential extraction procedure recommended by the Community Bureau of Reference (BCR), an improved nitric acid–sulphuric acid method, and diethylenetriamine pentaacetic acid (DTPA) extraction method, respectively. The results showed that a great percentage of the heavy metals remained in biochar, the concentrations of heavy metals in biochar (except Cd in B7) were higher than that in sludge, and the enrichment of the heavy metals in biochar enhanced with the pyrolysis temperature. Although the effect of pyrolysis temperature on the chemical speciation distribution, the leaching toxicity and the bio-available contents of heavy metals in biochar was inconsistent, the potential risk of biochar on soil and groundwater contamination was lower than sewage sludge.     

Accumulation and fate of selected heavy metals in a biological wastewater treatment system

The aim of this research was to study the accumulation and removal of heavy metals (Cd, Cu, Pb, Zn) by a biological wastewater treatment system. Heavy metal contents in the influent and effluent wastewater were compared. Also, the heavy metal contents in the sludge before and after anaerobic digestion were compared. The results showed: (1) more pronounced variations in the contents of Cu and Zn than that of Cd and Pb, which showed that at 0.02 for Cd and 0.05 mg/l for Pb, the reduction in their contents was insignificant; (2) that removal of heavy metals was directly proportional to their initial contents in the influent wastewater. Corresponding to the influent contents, in increasing order, the reduction in heavy metal contents was: Cd相似文献   

Variations of metal distribution in sewage sludge composting

In the study, the variations of heavy metal distributions (of Cu, Mn, Pb, and Zn) during the sewage sludge composting process were investigated by sequential extraction procedures. The total content of Cu and Zn in the composted mixture increased after the composting process. Mn and Zn were mainly found in mobile fractions (exchangeable fraction (F1), carbonate fraction (F2), and Fe/Mn oxide fraction (F3)). Cu and Pb were strongly associated with the stable fractions (organic matter/sulfides fraction (F4) and residual fraction (F5)). These five metal fractions were used to calculate the metal mobility (bioavailability) in the sewage sludge and composted mixture. The mobility (bioavailability) of Mn, Pb, and Zn (but not Cu) increased during the composting process. The metal mobility in the composted mixture ranked in the following order: Mn>Zn>Pb>Cu.