Pilot study on the advanced treatment of landfill leachate using a combined coagulation,fenton oxidation and biological aerated filter process

Mature landfill leachate is typically non-biodegradable. A combination process was developed that includes coagulation, Fenton oxidation, and biological aerated filtering to treat biologically-produced effluent. In this process, coagulation and Fenton oxidation were applied in order to reduce chemical oxygen demand (COD) organic load, and enhance biodegradability. Poly-ferric sulfate (PFS) at 600 mg l^?1 was found to be a suitable dosage for coagulation. For Fenton oxidation, an initial pH of 5, a total reaction time of 3 h, and an H₂O₂ dosage of 5.4 mmol l^?1, with a (H₂O₂)/n(Fe²⁺) ratio of 1.2 and two-step dosing were selected to achieve optimal oxidation. Under these optimal coagulation and Fenton oxidation conditions, the COD removal ratios were found to be 66.67% and 56%, respectively. Following pretreatment with coagulation and Fenton oxidation, the landfill leachate was further treated using a biological aerated filter (BAF). Our results show that COD was reduced to 75 mg l^?1, and the color was less than 10 degrees.     

Non-biodegradable landfill leachate treatment by combined process of agitation,coagulation, SBR and filtration

This study describes the complete treatment of non-biodegradable landfill leachate by combined treatment processes. The processes consist of agitation as a novel stripping method used to overcome the ammonia toxicity regarding aerobic microorganisms. The NH₃-N removal ratio was 93.9% obtained at pH 11.5 and a gradient velocity (G) 150 s^?1 within a five-hour agitation time. By poly ferric sulphate (PFS) coagulation followed the agitation process; chemical oxygen demand (COD) and biological oxygen demand (BOD₅) were removed at 70.6% and 49.4%, respectively at an optimum dose of 1200 mg L^?1 at pH 5.0. The biodegradable ratio BOD₅/COD was improved from 0.18 to 0.31 during pretreatment step by agitation and PFS coagulation. Thereafter, the effluent was diluted with sewage at a different ratio before it was subjected to sequencing batch reactor (SBR) treatment. Up to 93.3% BOD₅, 95.5% COD and 98.1% NH₃-N removal were achieved by SBR operated under anoxic–aerobic–anoxic conditions. The filtration process was carried out using sand and carbon as a dual filter media as polishing process. The final effluent concentration of COD, BOD₅, suspended solid (SS), NH₃-N and total organic carbon (TOC) were 72.4 mg L^?1, 22.8 mg L^?1, 24.2 mg L^?1, 18.4 mg L^?1 and 50.8 mg L^?1 respectively, which met the discharge standard. The results indicated that a combined process of agitation-coagulation-SBR and filtration effectively eliminated pollutant loading from landfill leachate.     

Greenhouse gas emissions from landfill leachate treatment plants: A comparison of young and aged landfill

With limited assessment, leachate treatment of a specified landfill is considered to be a significant source of greenhouse gas (GHG) emissions. In our study, the cumulative GHG emitted from the storage ponds and process configurations that manage fresh or aged landfill leachate were investigated. Our results showed that strong CH₄ emissions were observed from the fresh leachate storage pond, with the fluxes values (2219–26,489 mg C m^?2 h^?1) extremely higher than those of N₂O (0.028–0.41 mg N m^?2 h^?1). In contrast, the emission values for both CH₄ and N₂O were low for the aged leachate tank. N₂O emissions became dominant once the leachate entered the treatment plants of both systems, accounting for 8–12% of the removal of N-species gases. Per capita, the N₂O emission based on both leachate treatment systems was estimated to be 7.99 g N₂O–N capita^?1 yr^?1. An increase of 80% in N₂O emissions was observed when the bioreactor pH decreased by approximately 1 pH unit. The vast majority of carbon was removed in the form of CO₂, with a small portion as CH₄ (<0.3%) during both treatment processes. The cumulative GHG emissions for fresh leachate storage ponds, fresh leachate treatment system and aged leachate treatment system were 19.10, 10.62 and 3.63 Gg CO₂ eq yr^?1, respectively, for a total that could be transformed to 9.09 kg CO₂ eq capita^?1 yr^?1.     

Evaluation of landfill leachate treatment by advanced oxidative process by Fenton’s reagent combined with membrane separation system

A high content of refractory organic matter, ammonia and toxic compounds is characteristic of landfill leachate. Advanced oxidative processes (AOPs) are an attractive alternative for landfill leachate treatment. However, when applied as a unique process treatment, they do not provide a complete solution for the effluent treatment. Combining AOP with a membrane separation process (MSP) presents a number of benefits and provides an adequate solution for this problem. With this in mind, the present work aims to evaluate, using a bench scale, leachate treatability through AOP by Fenton’s reagent (AOP/Fenton) combined with microfiltration (MF) and nanofiltration (NF). A high efficient removal of COD (63%), true color (76%) and humic substances (50%) was observed during AOP/Fenton under optimized conditions (1.7 g H₂O₂/g COD_{raw leachate}; FeSO₄·7H₂O:H₂O₂ = 1:5.3; pH = 3.8; reaction conditions = 115 rpm/28 min). According to the evaluated parameters, MSP presented an efficient complementary treatment, in which the integrity of the stages was sufficient for reaching regulatory levels in the effluent (Deliberação Normativa Conjunta COPAM/CERH-MG N^o. 1, May 5, 2008).     

Fate of saline ions in a planted landfill site with leachate recirculation

Recirculation of leachate on a covered landfill site planted with willows or other highly evapotranspirative woody plants is an inexpensive option for leachate management. In our study, a closed landfill leachate recirculation system was established on a rehabilitated municipal solid waste landfill site with planted landfill cover. The main objective of the study was to evaluate the sustainability of the system with regard to high hydraulic loads of the landfill leachate on the landfill cover and high concentrations of saline ions, especially potassium (K⁺), sodium (Na⁺) and chloride (Cl^?), in leachate.The results of intensive monitoring, implemented during May 2004 and September 2007, including leachate, soil and plant samples, showed a high sustainability of the system regarding saline ions with the precipitation regime of the studied region. Saline ion concentrations in leachates varied between 132 and 2592 mg Cl^? L^?1, 69 and 1310 mg Na⁺ L^?1 and between 66 and 2156 mg K⁺ L^?1, with mean values of 1010, 632 and 686 mg L^?1, respectively. Soil salinity, measured as soil electrical conductivity (EC), remained between 0.17 and 0.38 mS cm^?1 at a depth between 0 and 90 cm. An average annual precipitation of 1000 mm provided sufficient leaching of saline ions, loaded by irrigation with landfill leachate, from the soil of the landfill cover and thus prevented possible salinity shocks to the planted willows.     

Nitrogen removal from landfill leachate via ex situ nitrification and sequential in situ denitrification

Ex situ nitrification and sequential in situ denitrification represents a novel approach to nitrogen management at landfills. Simultaneous ammonia and organics removal was achieved in a continuous stirred tank reactor (CSTR). The results showed that the maximum nitrogen loading rate (NLR) and the maximum organic loading rate (OLR) was 0.65 g N l^?1 d^?1 and 3.84 g COD l^?1 d^?1, respectively. The ammonia and chemical oxygen demand (COD) removal was over 99% and 57%, respectively. In the run of the CSTR, free ammonia (FA) inhibition and low dissolved oxygen (DO) were found to be key factors affecting nitrite accumulation. In situ denitrification was studied in a municipal solid waste (MSW) column by recalculating nitrified leachate from CSTR. The decomposition of MSW was accelerated by the recirculation of nitrified leachate. Complete reduction of total oxidized nitrogen (TON) was obtained with maximum TON loading of 28.6 g N t^?1 TS d^?1 and denitrification was the main reaction responsible. Additionally, methanogenesis inhibition was observed while TON loading was over 11.4 g N t^?1 TS d^?1 and the inhibition was enhanced with the increase of TON loading.     

Degradation of landfill leachate using transpiring-wall supercritical water oxidation (SCWO) reactor

Oxidation of landfill leachate wastewater was studied in a transpiring-wall SCWO reactor, operated under varied temperature and pressure 320–430 °C, 18–30 MPa. Effect of temperature and pressure on COD and BOD removal efficiency was investigated. COD and BOD removal efficiency being 99.23%, 98.06% were achieved at 430 °C, 30 MPa, which increased with temperature and pressure. The modified pseudo first-order rate model was regressed from experimental data, taking into account the induction time (t_ind) effect. The resulting pre-exponential factor A and activation energy E_a were 34.86 s^?1 and 32.1 kJ mol^?1, respectively, assuming that the reaction order for feed wastewater (based on COD) and oxidant were first order and zero order, respectively.     

Application of response surface methodology to the advanced treatment of biologically stabilized landfill leachate using Fenton’s reagent

A Fenton process that uses FeCl₂ as the alternative catalyst was employed to deal with the biologically treated landfill leachate. Data obtained revealed that this Fenton process can provide an equivalent pollutant removal as the Fenton process that uses FeSO₄ as catalyst. Central composite design (CCD) and response surface methodology (RSM) were applied to evaluate and optimize the four key factors, namely initial pH, Fe(II) dosage ([Fe²⁺]), H₂O₂/Fe(II) mole ratio ([H₂O₂]/[Fe²⁺] ratio) and reaction time, which affect the performance of the Fenton treatment. Chemical oxygen demand (COD) and color were selected as response variables. This approach provided statistically significant quadratic models, which were adequate to predict responses and to carry out optimization under the conditions studied. It was demonstrated that the interaction between initial pH and [H₂O₂]/[Fe²⁺] ratio has a significant effect on the COD removal, while the interaction between [H₂O₂]/[Fe²⁺] ratio and reaction time shows a large impact on color removal. The optimal conditions were found to be initial pH 5.9, [Fe²⁺] = 9.60 mmol/L, [H₂O₂]/[Fe²⁺] ratio = 2.38, reaction time = 5.52 h. Under this optimal scheme, the COD and color in the effluent were reduced to 159 mg/L and 25°, respectively, with an increase of BOD₅/COD ratio from 0.05 to 0.21.     

A comparative study of two composts as filter media for the removal of gaseous reduced sulfur compounds (RSCs) by biofiltration: Application at industrial scale

This work presents the use of two composts as filter media for the treatment by biofiltration of odors emitted during the aerobic composting of a mixture containing sewage sludge and yard waste. The chemical analysis of the waste gas showed that the malodorous compounds at trace level were the reduced sulfur compounds (RSCs) which were dimethyl sulfide (Me₂S), methanethiol (MeSH) and hydrogen sulfide (H₂S). Laboratory tests for biofiltration treatment of RSCs were performed in order to compare the properties of two filter media, consisted of a mature compost with yard waste (YW) and a mixture of mature compost with sewage sludge and yard waste (SS/YW). The maximum elimination capacity (EC) values obtained with the YW mature compost as packing material were 12.5 mg m^?3 h^?1 for H₂S, 7.9 mg m^?3 h^?1 for MeSH and 34 mg m^?3 h^?1 for Me₂S, and the removal efficiency decreased in the order of: H₂S > MeSH > Me₂S. Moreover, the YW compost filter medium had a better behavior than the filter medium based on SS/YW in terms of acclimation of the microbial communities and moisture content. According to these results, a YW mature compost as packing material for an industrial biofilter were designed and this industrial biofilter was found effective under specified conditions (without inoculation and addition of water). The results showed that the maximum EC value of RSCs was 935 mg m^?3 h^?1 (100% removal efficiency, RE) for an inlet loads (IL) between 0 and 1000 mg m^?3 h^?1. Thus, YW compost medium was proven efficient for biofiltration of RSCs both at laboratory and industrial scale.     

Nutrient release from bisulfate-amended phytase-diet poultry litter under simulated weathering conditions

Poultry litter generated on the Delmarva Peninsula is from phytase-modified bird diet and bisulfate amendment. To establish agronomic application rates in conservation tillage systems, bisulfate-amended phytase-diet poultry litter was investigated for its nutrient release kinetics and supply capacity under simulated weathering conditions. Delmarva poultry litter was packed in PVC columns (15 cm i.d. × 25 cm height) to a depth of 5 cm and leached intermittently with 600 mm of water for 190 days. Concentrations of various nutrients in leachate were analyzed and nutrient release kinetics were modelled. Poultry litter leachate contained high contents of dissolved organic carbon (DOC, 35–11,800 mg L^?1), nitrogen (N 6–2690 mg L^?1), phosphorus (P 45–225 mg L^?1), potassium (K 20–6060 mg L^?1), and other nutrients. Release of the nutrients occurred primarily in the starting 5 weeks and mostly followed a first order Exponential-Rise-to-Maximum model. Under the specified conditions, the poultry litter demonstrated a nutrient supply capacity of 11.7 kg N Mg^?1, 5.4 kg P Mg^?1, and 36.8 kg K Mg^?1. Release of the potentially plant-available N and K was nearly finalized within 190 days of leaching/weathering, but it would require two years for full release of the leachable P. The results indicate that with consideration of field conditions, surface application of bisulfate-amended phytase-diet Delmarva poultry litter at recommended 6.6 Mg ha^?1 to conservation tillage systems would largely provide P 25.0 kg ha^?1, N 106.6 kg ha^?1, and K 245.5 kg ha^?1 to seasonal crops.     

Impact of nitrate-enhanced leachate recirculation on gaseous releases from a landfill bioreactor cell

This study evaluates the impact of nitrate injection on a full scale landfill bioreactor through the monitoring of gaseous releases and particularly N₂O emissions. During several weeks, we monitored gas concentrations in the landfill gas collection system as well as surface gas releases with a series of seven static chambers. These devices were directly connected to a gas chromatograph coupled to a flame ionisation detector and an electron capture detector (GC-FID/ECD) placed directly on the field. Measurements were performed before, during and after recirculation of raw leachate and nitrate-enhanced leachate. Raw leachate recirculation did not have a significant effect on the biogas concentrations (CO₂, CH₄ and N₂O) in the gas extraction network. However, nitrate-enhanced leachate recirculation induced a marked increase of the N₂O concentrations in the gas collected from the recirculation trench (100-fold increase from 0.2 ppm to 23 ppm). In the common gas collection system however, this N₂O increase was no more detectable because of dilution by gas coming from other cells or ambient air intrusion. Surface releases through the temporary cover were characterized by a large spatial and temporal variability. One automated chamber gave limited standard errors over each experimental period for N₂O releases: 8.1 ± 0.16 mg m^?2 d^?1 (n = 384), 4.2 ± 0.14 mg m^?2 d^?1 (n = 132) and 1.9 ± 0.10 mg m^?2 d^?1 (n = 49), during, after raw leachate and nitrate-enhanced leachate recirculation, respectively. No clear correlation between N₂O gaseous surface releases and recirculation events were evidenced. Estimated N₂O fluxes remained in the lower range of what is reported in the literature for landfill covers, even after nitrate injection.     

Phytoremediation of landfill leachate and compost wastewater by irrigation of Populus and Salix: Biomass and growth response

A pot experiment is described with a fast-growing poplar clone and two native willows (Populus deltoides Bartr. cl. I-69/55 (Lux)), Salix viminalis L. and Salix purpurea L.), irrigated with landfill leachate and compost wastewater over a 1-year growing period. The use of leachate resulted in up to 155% increased aboveground biomass compared to control water treatments and in up to 28% reduced aboveground biomass compared to a complete nutrient solution. The use of compost wastewater resulted in up to 62% reduced aboveground biomass compared to the control treatments and in up to 86% reduced aboveground biomass compared to the complete nutrient solution. Populus was the most effective in biomass production due to the highest leaf production, whereas S. purpurea was the least effective in biomass accumulation, but less sensitive to high ionic strength of the irrigation water compared to S. viminalis. The results showed a high potential for landfill leachate application (with up to 2144 kg N ha^?1, 144 kg P ha^?1, 709 kg K ha^?1, 1010 kg Cl ha^?1, and 1678 kg Na ha^?1 average mass load in the experiment). High-strength compost wastewater demonstrated less potential for application as irrigation and fertilization source even in high water-diluted treatments (1:8 by volume).     

Physico-chemical and biological treatment of MSW landfill leachate

This paper analyses the evolution of the physico-chemical characteristics of the leachate from the Central Landfill of Asturias (Spain), which has been operating since 1986, as well as different treatment options. The organic pollutant load of the leachate, expressed as chemical oxygen demand (COD), reached maximum values during the first year of operation of the landfill (around 80,000 mg/L), gradually decreasing over subsequent years to less than 5000 mg/L. The concentration of ammonium, however, has not decreased, presenting values of up to 2000 mg/L. When feasible, recirculation can greatly decrease the organic matter content of the leachate to values of 1500–1600 mg COD/L. Applying anaerobic treatment to leachates with a COD between 11,000 and 16,000 mg/L, removal efficiencies of 80–88% were obtained for organic loading rates of 7 kg COD/m³ d. For leachates with lower COD (4000–6000 mg/L), the efficiency decreased to around 60% for organic loading rates of 1 kg COD/m³ d.Applying coagulation–flocculation with iron trichloride or with aluminium polychloride, it was possible to reduce the non-biodegradable organic matter by 73–62% when treating old landfill leachate (COD: 4800 mg/L, BOD₅: 670 mg/L), also reducing turbidity and colour by more than 97%. It is likewise possible to reduce the non-biodegradable organic matter that remains after biological treatment by adsorption with activated carbon, although adsorption capacities are usually low (from 15 to 150 mg COD/g adsorbent). As regards ammonium nitrogen, this can be reduced to final effluent values of 5 mg/L by means of nitrification/denitrification and to values of 126 mg/L by stripping at pH 12 and 48 h of stirring.     

Tracer method to measure landfill gas emissions from leachate collection systems

This paper describes a method developed for quantification of gas emissions from the leachate collection system at landfills and present emission data measured at two Danish landfills with no landfill gas collection systems in place: Fakse landfill and AV Miljø. Landfill top covers are often designed to prevent infiltration of water and thus are made from low permeable materials. At such sites a large part of the gas will often emit through other pathways such as the leachate collection system. These point releases of gaseous constituents from these locations cannot be measured using traditional flux chambers, which are often used to measure gas emissions from landfills. Comparing tracer measurements of methane (CH₄) emissions from leachate systems at Fakse landfill and AV Miljø to measurements of total CH₄ emissions, it was found that approximately 47% (351 kg CH₄ d^?1) and 27% (211 kg CH₄ d^?1), respectively, of the CH₄ emitting from the sites occurred from the leachate collection systems. Emission rates observed from individual leachate collection wells at the two landfills ranged from 0.1 to 76 kg CH₄ d^?1. A strong influence on emission rates caused by rise and fall in atmospheric pressure was observed when continuously measuring emission from a leachate well over a week. Emission of CH₄ was one to two orders of magnitude higher during periods of decreasing pressure compared to periods of increasing pressure.     

Changes in cadmium mobility during composting and after soil application

The effect of twelve weeks of composting on the mobility and bioavailability of cadmium in six composts containing sewage sludge, wood chips and grass was studied, along with the cadmium immobilization capacity of compost. Two different soils were used and Cd accumulation measured in above-ground oat biomass (Avena sativa L.). Increasing pH appears to be an important cause of the observed decreases in available cadmium through the composting process. A pot experiment was performed with two different amounts of compost (9.6 and 28.8 g per kg of soil) added into Fluvisol with total Cd 0.255 mg kg^?1, and contaminated Cambisol with total Cd 6.16 mg kg^?1. Decrease of extractable Cd (0.01 mol l^?1 CaCl₂) was found in both soils after compost application. The higher amount of compost immobilized an exchangeable portion of Cd (0.11 mol l^?1 CH₃COOH extractable) in contaminated Cambisol unlike in light Fluvisol. The addition of a low amount of compost decreased the content of Cd in associated above-ground oat biomass grown in both soils, while a high amount of compost decreased the Cd content in oats only in the Cambisol.     

Treatment of municipal landfill leachate using a combined anaerobic digester and activated sludge system

The main objective of this study was to assess the feasibility of treating sanitary landfill leachate using a combined anaerobic and activated sludge system. A high-strength leachate from Shiraz municipal landfill site was treated using this system. A two-stage laboratory-scale anaerobic digester under mesophilic conditions and an activated sludge unit were used. Landfill leachate composition and characteristics varied considerably during 8 months experiment (COD concentrations of 48,552–62,150 mg/L). It was found that the system could reduce the COD of the leachate by 94% at a loading rate of 2.25 g COD/L/d and 93% at loading rate of 3.37 g COD/L/d. The anaerobic digester treatment was quite effective in removing Fe, Cu, Mn, and Ni. However, in the case of Zn, removal efficiency was about 50%. For the rest of the HMs the removal efficiencies were in the range 88.8–99.9%. Ammonia reduction did not occur in anaerobic digesters. Anaerobic reactors increased alkalinity about 3.2–4.8% in the 1st digester and 1.8–7.9% in the 2nd digester. In activated sludge unit, alkalinity and ammonia removal efficiency were 49–60% and 48.6–64.7%, respectively. Methane production rate was in the range of 0.02–0.04, 0.04–0.07, and 0.02–0.04 L/g COD_rem for the 1st digester, the 2nd digester, and combination of both digesters, respectively; the methane content of the biogas varied between 60% and 63%.     

Landfill leachate treatment by electrochemical oxidation

This study investigated the electrochemical oxidation of stabilized leachate from Pulau Burung semi-aerobic sanitary landfill by conducting laboratory experiments with sodium sulfate Na₂SO₄ (as electrolyte) and graphite carbon electrodes. The control parameters were influent COD, current density and reaction time, while the responses were BOD removal, COD removal, BOD:COD ratio, color and pH. Na₂SO₄ concentration was 1 g/L. Experiments were conducted based on a three-level factorial design and response surface methodology (RSM) was used to analyze the results. The optimum conditions were obtained as 1414 mg/L influent COD concentration, 79.9 mA/cm² current density and 4 h reaction time. This resulted in 70% BOD removal, 68% COD removal, 84% color removal, 0.04 BOD/COD ratio and 9.1 pH. Electrochemical treatment using graphite carbon electrode was found to be effective in BOD, COD and color removal but was not effective in increasing the BOD/COD ratio or enhancing biodegradability of the leachate. The color intensity of the treated samples increased at low influent COD and high current density due to corrosion of electrode material.     

Spatial variability of nitrous oxide and methane emissions from an MBT landfill in operation: Strong N2O hotspots at the working face

Mechanical biological treatment (MBT) is an effective technique, which removes organic carbon from municipal solid waste (MSW) prior to deposition. Thereby, methane (CH₄) production in the landfill is strongly mitigated. However, direct measurements of greenhouse gas emissions from full-scale MBT landfills have not been conducted so far. Thus, CH₄ and nitrous oxide (N₂O) emissions from a German MBT landfill in operation as well as their concentrations in the landfill gas (LFG) were measured. High N₂O emissions of 20–200 g CO₂ eq. m^?2 h^?1 magnitude (up to 428 mg N m^?2 h^?1) were observed within 20 m of the working face. CH₄ emissions were highest at the landfill zone located at a distance of 30–40 m from the working face, where they reached about 10 g CO₂ eq. m^?2 h^?1. The MBT material in this area has been deposited several weeks earlier. Maximum LFG concentration for N₂O was 24.000 ppmv in material below the emission hotspot. At a depth of 50 cm from the landfill surface a strong negative correlation between N₂O and CH₄ concentrations was observed. From this and from the distribution pattern of extractable ammonium, nitrite, and nitrate it has been concluded that strong N₂O production is associated with nitrification activity and the occurrence of nitrite and nitrate, which is initiated by oxygen input during waste deposition. Therefore, CH₄ mitigation measures, which often employ aeration, could result in a net increase of GHG emissions due to increased N₂O emissions, especially at MBT landfills.     

Liquid balance monitoring inside conventional,Retrofit, and bio-reactor landfill cells

The Outer Loop landfill bioreactor (OLLB) in Louisville, KY, USA has been the site of a study to evaluate long-term bioreactor performance at a full-scale operational landfill. Three types of landfill units were studied including a conventional landfill (Control cell), a new landfill area that had an air addition and recirculation piping network installed as waste was being placed (As-Built cell), and a conventional landfill that was modified to allow for liquids recirculation (Retrofit cell). During the monitoring period, the Retrofit, Control, and As-Built cells received 48, 14, and 213 L Mg^?1 (liters of liquids per metric ton of waste), respectively. The leachate collection system yielded 60, 57 and 198 L Mg^?1 from the Retrofit, Control, and As-Built cells, respectively. The head on liner in all cells was below regulatory limits. In the Control and As-Built cells, leachate head on liner decreased once waste placement stopped. The measured moisture content of the waste samples was consistent with that calculated from the estimate of accumulated liquid by the liquid balance. Additionally, measurements on excavated solid waste samples revealed large spatial variability in waste moisture content. The degree of saturation in the Control cells decreased from 85% to 75%. The degree of saturation increased from 82% to 83% due to liquids addition in the Retrofit cells and decreased back to 80% once liquid addition stopped. In the As-Built cells, the degree of saturation increased from 87% to 97% during filling activities and then started to decrease soon after filling activities stopped to reach 92% at the end of the monitoring period. The measured leachate generation rates were used to estimate an in-place saturated hydraulic conductivity of the MSW in the range of 10^?8 to 10^?7 m s^?1 which is lower than previous reports. In the Control and Retrofit cells, the net loss in liquids, 43 and 12 L Mg^?1, respectively, was similar to the measured settlement of 15% and 5–8% strain, respectively (Abichou et al., 2013). The increase in net liquid volume in the As-Built cells indicates that the 37% (average) measured settlement strain in these cells cannot be due to consolidation as the waste mass did not lose any moisture but rather suggests that settlement was attributable to lubrication of waste particle contacts, softening of flexible porous materials, and additional biological degradation.     

Characterization of residues from dismantled imported wastes

Residues from the imported wastes dismantling process create a great burden on the ambient environment. To develop appropriate strategies for the disposal of such residues, their characteristics were studied through background value analysis and toxicity leaching tests. Our results showed that the heavy metals concentrations in residues were high, particularly those of Cu (7180 mg kg^?1), Zn (2783 mg kg^?1), and Pb (1954 mg kg^?1). Toxicity leaching tests revealed a high metal releasing risk of such residues if they are disposed of in a landfill. However, the residues of imported wastes were also found to have some intrinsic metal recycling value.