TiO_2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有：X射线衍射光谱（XRD）、激光散射粒径分布、傅立叶变换红外光谱（FT-IR）、X射线光电子谱（XPS）和透射电子显微镜（TEM）。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂（H2O2）用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明：制备的TiO2胶体粒子平均粒径为13.8 nm（激光散法测定）,光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/（L.min）,平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2（含量30%）用量为0.2%（V/V）,光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

改性MIL-101(Fe)非均相芬顿反应降解罗丹明B

金属有机骨架材料MIL-101(Fe)具有一定的催化活性,为进一步提升其催化性能,利用金属掺杂和柠檬酸调节对其进行改性,制备得到Cu/Ce-MIL-101(Fe)和Cu/Ce-MIL-101(Fe)-N两种改性材料。通过X射线衍射(XRD)、傅立叶变换红外光谱(FT-IR)、场发射扫描电镜(SEM)、氮气吸附脱附测试及X射线光电子能谱(XPS)对材料进行表征。结果显示,改性后催化剂具有相似的骨架结构和化学键组成,活性位点的结合能减少0.2～0.3 eV。金属掺杂和柠檬酸调节改性后Cu/Ce-MIL-101(Fe)-N平均孔径增大至14.932 nm。采用非均相芬顿反应研究降解时间和pH对罗丹明B降解性能的影响,结果表明,在温度为25℃,罗丹明B初始质量浓度为24 mg/L,溶液pH为4且Cu/Ce-MIL-101(Fe)-N投加量为0.2 g/L,3%(体积分数) H₂O₂投加量为60 mL/L,反应60 min时,罗丹明B降解率高达98%。改性前后催化剂降解过程均更符合准一级动力学模型。其中,Cu/Ce-MIL-101(Fe)-N能够在60...     

异相可见光Fenton催化降解罗丹明B的研究

用溶胶凝胶法成功制备了异相可见光Photo-Fenton试剂BiFeO3,并对其形貌等物理化学性质进行表征.考察了异相可见光Fenton体系下罗丹明B的降解情况,2.50h后10 mg/L罗丹明B被BiFeO3-Fenton可见光催化并全部降解,证实BiFeO3是很好的异相可见光Photo-Fenton催化剂.利用液相色谱—质谱联用(LC/MS)鉴定分析了罗丹明B降解中间产物,共检测到4种脱乙基产物,初步认为罗丹明B在BiFeO3-H2O2体系下降解主要途径是逐步脱乙基反应.     

漂浮型可见光复合光催化剂B-N-TiO_2/EP的制备、表征及其光催化性能

以膨胀珍珠岩为漂浮型载体,采用溶胶凝胶法制备B和N共掺杂的B-N-TiO_2/EP可见光催化材料和单一N掺杂的N-TiO_2/EP可见光催化材料。应用X射线粉末衍射(XRD)、扫描电镜(SEM)、紫外-可见(UV-Vis)光谱、N2吸脱附(BET)、X射线光电子能谱(XPS)等手段对催化剂进行表征。并以可见光为光源,评价了该催化剂催化降解罗丹明B的活性,考察了不同B掺杂量对该催化材料性能的影响。实验结果表明,与N-TiO_2/EP相比,B-N-TiO_2/EP吸收光谱发生了明显的红移,可见光吸收强度更大。B的掺杂可以抑制TiO_2晶型从锐钛矿向金红石的转变。B0.57-N-TiO_2/EP对罗丹明B降解效果最好,可见光条件下反应3 h,罗丹明B去除率高达93%以上,B0.57-N-TiO_2/EP催化材料重复利用4次仍有75%的去除率,显示了较好的稳定性和重复利用性。     

三维过电位电解处理罗丹明B废水

选用钛基RuO2-TiO2涂层电极作为三维过电位电解装置的阳极，紫铜作为阴极，活性炭作为第三极，研究了三维过电位电解处理罗丹明B废水的效果，并考察了外加电压、电解时间、初始浓度、pH值和搅拌方式等因素对其处理效果的影响。实验结果表明，外加电压、电解时间和初始浓度等因素均对罗丹明B的降解效果有影响，而pH值、搅拌方式等对罗丹明B的降解效果基本没有影响。与二维电解的对比研究表明，在罗丹明B溶液初始浓度为20mg／L，电解时间为1h，电解电压为20V时，采用二维电解的降解率为20％左右，而三维过电位电解的降解率接近80％。最终产物分析结果显示，经过处理的罗丹明B苯环开环变成直链烃类物质，或者饱和环状有机物，不再具有生物毒性，适合后续的生化处理。     

Cu-SBA-15催化湿式过氧化氢氧化水溶液中罗丹明B

采用水热晶化法合成了不同含铜量的Cu-SBA-15介孔分子筛,并且用XRD、N2吸附、TEM以及UV-vis对所合成的样品进行表征。以Cu-SBA-15为催化剂,H2O2为氧化剂,催化湿式过氧化水溶液中的罗丹明B,主要考察H2O2浓度、催化剂用量、处理温度、初始pH等因素对罗丹明B氧化效果的影响。结果表明,在同样的处理条件下罗丹明的脱色率明显高于TOC去除率,处理温度、初始pH对罗丹明B的脱色与氧化有重要影响。在罗丹明B初始浓度100 mg/L,H2O2初始浓度1.8 g/L,催化剂量0.3 g/L,温度60℃,pH为7.0,处理时间100 min时,罗丹明B的脱色率为98.6%,TOC去除率为62.8%。     

含表面活性剂的采油废水催化氧化处理

对含有表面活性剂的废水(以下简称表活废水)进行了傅里叶红外光谱分析(FTIR),结果表明,废水中所含表面活性剂主要为环烷酸钠。采用次氯酸钙(Ca(ClO)2)和活性炭-Ni催化氧化处理,在Ca(ClO)2投加量为4 500 mg/L,活性炭-Ni投加量为7 000 mg/L时,反应90 min,出水COD为158.91 mg/L,去除率达62.92%。催化氧化出水经沸石吸附处理,在pH为6.85,吸附时间为2 h,沸石投加量为17 g/L的条件下,吸附出水COD和油含量分别为88.92 mg/L和2.53mg/L,去除率分别为45.65%和90.02%,均达到《污水综合排放标准(GB8978-1996)》的一级标准要求。催化剂活性炭-Ni和吸附剂沸石均具有较稳定的活性,在重复使用20次后,出水COD的去除率仅分别降低了1.16%和1.32%。     

十六烷基三甲基溴化铵改性沸石对腐殖酸的吸附性能研究

以十六烷基三甲基溴化铵(CTAB)为改性剂,制备了CTAB改性沸石,并用于对腐殖酸的吸附性能研究。考察了pH、吸附时间及腐殖酸初始浓度对CTAB改性沸石吸附腐殖酸的影响,采用吸附等温方程和反应动力学方程进行拟合分析,并利用扫描电子显微镜(SEM)、X射线光电子能谱仪(XPS)、傅立叶转换红外光谱分析仪(FTIR)对沸石改性前后进行结构表征。结果表明,在温度为25℃、转速为200r/min的条件下,选择pH为7.0、腐殖酸初始质量浓度为10mg/L、吸附时间为180min,此时CTAB改性沸石对腐殖酸的平衡吸附容量为0.16mg/g。相比Freundlich吸附等温方程(R2=0.967),CTAB改性沸石对腐殖酸的吸附更符合Langmuir吸附等温方程(R2=0.998),吸附机制为单分子层吸附。准一级反应动力学方程和准二级反应动力学方程均可以描述CTAB改性沸石对腐殖酸的吸附(R2=0.978)。吸附实验后的CTAB改性沸石上出现了甲基、亚甲基、羟基与羰基伸缩振动吸收峰,说明沸石已负载了CTAB,且腐殖酸已被CTAB改性沸石吸附。     

高铁酸钾的超声辅助化学合成及其对餐厨垃圾渗滤液的处理效果

采用超声辅助化学合成法制备K2Fe O4,用X-射线衍射、红外光谱和扫描电镜等对其进行表征。研究了K2Fe O4对餐厨垃圾渗滤液中COD和氨氮的处理效果。结果表明,本法制备的K2Fe O4具有四方结构,空间群为D2h(Pnma),其产率达到68.2%,纯度高达98.3%。扫描电镜表明,制备的K2Fe O4由规则的条状颗粒组成,颗粒之间存在一定团聚。对餐厨渗滤液处理实验表明,在COD初始浓度为140.6 g/L的餐厨垃圾渗滤液中投加0.12 mol/L K2Fe O4,调节p H为8.7,经处理24 min后COD去除率达到80.4%,氨氮的去除率达到75.9%。     

Adsorptive removal and photocatalytic decomposition of sulfamethazine in secondary effluent using TiO2–zeolite composites

We investigated the adsorption and decomposition of sulfamethazine (SMT), which is used as a synthetic antibacterial agent and discharged into environmental water, using high-silica Y-type zeolite (HSZ-385), titanium dioxide (TiO₂), and TiO₂–zeolite composites. By using ultrapure water and secondary effluent as solvents, we prepared SMT solutions (10 μg/L and 10 mg/L) and used them for adsorption and photocatalytic decomposition experiments. When HSZ-385 was used as an adsorbent, rapid adsorption of SMT in the secondary effluent was confirmed, and the adsorption reached equilibrium within 10 min. The photocatalytic decomposition rate using TiO₂ in the secondary effluent was lower than that in ultrapure water, and we clarified the inhibitory effect of ions and organic matter contained in the secondary effluent on the reaction. We synthesized TiO₂–zeolite composites and applied them to the removal of SMT. During the treatment of 10 μg/L SMT in the secondary effluent using the composites, 76 % and more than 99 % of the SMT were decomposed within 2 and 4 h by photocatalysis. The SMT was selectively adsorbed onto high-silica Y-type zeolite in the composites. Resultantly, the inhibitory effect of the coexisting materials was reduced, and the composites could remove SMT more effectively compared with TiO₂ alone in the secondary effluent.     

海水改性沸石处理氨氮废水

沸石因具有独特的架状结构而表现出良好的选择吸附和离子交换性能,在废水处理中被广泛应用,但吸附容量偏低,需要进行改性。针对天然沸石的局限性,研究了不同改性方法对氨氮吸附的影响,确定了最佳的沸石改性方法,并进行了吸附等温模型,吸附动力学研究。结果表明,采用高温300℃焙烧后再用预处理后的海水浸泡24 h改性沸石去除氨氮效果最佳。当活化沸石投配量为10 g/L,接触时间为150 min,进水氨氮浓度为37.91 mg/L时,沸石对氨氮吸附容量为4.08 mg/g,氨氮去除率为90.45%;沸石及改性沸石对氨氮的吸附等温线符合Langmuir方程和准一级动力学方程。用海水来改性沸石的方法,不仅可提高沸石对氨氮的吸附容量和吸附速度,而且无任何添加药剂,具有简单易行、费用低廉的优点,为沸石在水处理工程中的应用提供技术支撑。     

Treatment of wastewater from red and tropical fruit wine production by zeolite anaerobic fluidized bed reactor

A study of the anaerobic treatment of wastewaters derived from red (RWWW) and tropical fruit wine (TFWWW) production was carried out in four laboratory-scale fluidized bed reactors with natural zeolite as bacterial support. These reactors operated at mesophilic temperature (35 degrees C). Reactors R1 and R2 contained Chilean natural zeolite, while reactors R3 and R4 used Cuban natural zeolite as microorganism support. In addition, reactors R1 and R3 processed RWWW, while reactors R2 and R4 used TFWWW as substrate. The biomass concentration attached to zeolites in the four reactors studied was found to be in the range of 44-46 g volatile solids (VS)/L after 90 days of operation time. Both types of zeolites can be used indistinctly in the fluidized bed reactors achieving more than 80%-86% chemical oxygen demand (COD) removals for organic loading rates (OLR) of up to at least 20 g COD/L d. pH values remained within the optimal range for anaerobic microorganisms for OLR values of up to 20 and 22 g COD/L d for RWWW and TFWWW, respectively. Toxicity and inhibition levels were observed at an OLR of 20 g COD/L d in reactors R1 and R3 while processing RWWW, whereas the aforementioned inhibitory phenomena were not observed at an OLR of 24 g COD/L d in R2 and R4, treating TFWWW as a consequence of the lower phenolic compound content present in this substrate. The volatile fatty acid (VFA) levels were always lower in reactors processing TFWWW (R2 and R4) and these values (< 400 mg/L, as acetic acid) were lower than the suggested limits for digester failure. The specific methanogenic activity (SMA) was twice as high in reactors R2 and R4 than in R1 and R3 after 120 days of operation when all reactors operated at an OLR of 20 g COD/L d.     

Treatment of wastewater from red and tropical fruit wine production by zeolite anaerobic fluidized bed reactor

A study of the anaerobic treatment of wastewaters derived from red (RWWW) and tropical fruit wine (TFWWW) production was carried out in four laboratory-scale fluidized bed reactors with natural zeolite as bacterial support. These reactors operated at mesophilic temperature (35°C). Reactors R1 and R2 contained Chilean natural zeolite, while reactors R3 and R4 used Cuban natural zeolite as microorganism support. In addition, reactors R1 and R3 processed RWWW, while reactors R2 and R4 used TFWWW as substrate. The biomass concentration attached to zeolites in the four reactors studied was found to be in the range of 44–46 g volatile solids (VS)/L after 90 days of operation time. Both types of zeolites can be used indistinctly in the fluidized bed reactors achieving more than 80%–86% chemical oxygen demand (COD) removals for organic loading rates (OLR) of up to at least 20 g COD/L d. pH values remained within the optimal range for anaerobic microorganisms for OLR values of up to 20 and 22 g COD/L d for RWWW and TFWWW, respectively. Toxicity and inhibition levels were observed at an OLR of 20 g COD/L d in reactors R1 and R3 while processing RWWW, whereas the aforementioned inhibitory phenomena were not observed at an OLR of 24 g COD/L d in R2 and R4, treating TFWWW as a consequence of the lower phenolic compound content present in this substrate. The volatile fatty acid (VFA) levels were always lower in reactors processing TFWWW (R2 and R4) and these values (< 400 mg/L, as acetic acid) were lower than the suggested limits for digester failure. The specific methanogenic activity (SMA) was twice as high in reactors R2 and R4 than in R1 and R3 after 120 days of operation when all reactors operated at an OLR of 20 g COD/L d.     

Fe/活性炭多相类Fenton法湿式氧化罗丹明B废水的研究

采用自制的Fe/活性炭（Fe/AC）为催化剂，H₂O₂为氧化剂,组成多相类Fenton试剂催化降解罗丹明B染料废水。实验结果表明,在催化剂加入量为0.8 g/L，H₂O₂体积分数为0.3%,废水pH值为13,反应时间为30 min的条件下,质量浓度为200 mg/L的罗丹明B染料废水的脱色率达100%。反应动力学研究表明,罗丹明B脱色反应近似为一级反应,30℃时反应速率常数为0.02675 min^-1,表观活化能为69.47 kJ/mol。     

改性沸石吸附低浓度氨氮废水及其脱附的研究

采用氯化钠溶液对浙江某地天然沸石改性,以低浓度氨氮废水为处理对象,比较了天然沸石和改性沸石的吸附等温线、吸附动力学和动态吸附,并进行了改性沸石的动态脱附研究.结果表明,沸石的平衡吸附量随着平衡浓度的增大而增大;Freundlich方程比Langmuir方程更好地描述沸石吸附低浓度氨氮废水的行为,改性沸石比天然沸石具有更...     

亚铁催化声化学降解罗丹明B

比较了不同金属离子对罗丹明B的声化学降解作用,发现超声时加入Fe2 反应速率常数为单独超声波降解时的1.6倍,反应在前5 h内符合假一级动力学.研究了亚铁离子强化声化学对罗丹明B的降解作用,考察了Fe2 用量,溶液初始pH值,曝气,反应温度和超声功率等因素对脱色速率的影响.研究表明,酸性条件有利于染料的脱色;有曝气时的声化学脱色速率常数是单独超声时的6倍;声化学反应的活化能较低,反应在低温就可以进行;超声功率的改变对脱色速率的影响不大.UV-VIS扫描图谱显示,染料在225 nm和256 nm处的紫外吸收明显降低,初步探讨了罗丹明B的降解机理.     

活性炭和沸石对氨氮的吸附特性及生物再生

采用活性炭和沸石作为吸附材料,分别考察了这两种吸附材料对水体中氨氮的吸附特性及其生物再生性能。实验结果表明,活性炭和沸石对水体中氨氮的等温吸附符合Freundlich等温式,其拟合度分别为0.9783和0.9303;静态吸附结果表明活性炭和沸石均具有较好的氨氮吸附性能,24 h内沸石对氨氮的吸附能力为1.27 mg/g,高于活性炭的0.53 mg/g;动态吸附中沸石达到吸附饱和的时间为96 h,较活性炭达到吸附饱和的时间长,沸石显示出作为氨氮吸附剂的优越性;活性炭和沸石经过96 h的生物再生后吸附性能获得一定程度的再生,出水中氨氮浓度比未进行生物再生前分别降低17.31 mg/L和8.32 mg/L,且都在表面形成了稳定的生物膜。