Kinetics and stoichiometry of aerobic sulfide oxidation in wastewater from sewers-effects of pH and temperature.

Kinetics and stoichiometry of aerobic chemical and biological sulfide oxidation in wastewater from sewer networks were studied. In this respect, the effects of temperature and pH were investigated in the ranges 10 to 20 degrees C and 5 to 9, respectively. The temperature dependency of sulfide oxidation kinetics was described using an Arrhenius relationship. The effect of pH on the rate of chemical sulfide oxidation is related to the dissociation of hydrogen sulfide (H2S) to hydrogen sulfide ion (HS(-)), with HS(-) being more readily oxidized than H2S. Biological sulfide oxidation exhibited the highest rates at ambient wastewater pH, and the reaction was inhibited at both low and high pH values. Chemical sulfide oxidation was found to produce thiosulfate and sulfate, while elemental sulfur was the main product of biological sulfide oxidation. Based on the investigations, general rate equations and stoichiometric constants were determined, enabling the processes to be incorporated to conceptual sewer process models.     

Decolorization and degradation of H-acid and other dyes using ferrous-hydrogen peroxide system

In this study, advanced oxidation process utilizing Fenton's reaction was investigated for the decolorization and degradation of two commercial dyes viz., Red M5B, Blue MR and H-acid, a dye intermediate used in chemical industries for the synthesis of direct, reactive and azo dyes. Effect of Fe2 +, H2O2, pH, and contact time on the degradation of the dyes was studied. Maximum color and COD removal was obtained for Red MSB, H-acid and Blue MR at 10-25 mg/l of Fe2+ dose and 400-500 mg/l of H2O2 dose at pH 3.0. The initial oxidation reaction was found to fit into first order rate kinetics and the rate of oxidation of H-acid was higher than the other dyes. Release of chloride and sulfate from the Fenton's treated Red M5B dye and sulfate from H-acid and Blue MR indicates that the dye degradation proceeds through cleavage of the substituent group.     

Influence of pH on persulfate oxidation of TCE at ambient temperatures

In situ chemical oxidation (ISCO) is a technology used for groundwater remediation. This laboratory study investigated the use of the oxidant sodium persulfate for the chemical oxidation of trichloroethylene (TCE) at near ambient temperatures (10, 20 and 30 degrees C) to determine the influence of pH (pH=4, 7 and 9) on the reaction rate (i.e., pseudo-first-order rate constants) over the range of temperatures utilized. TCE solutions (60 mg l(-1); 0.46 mM) were prepared in phosphate buffered RO water and a fixed persulfate/TCE molar ratio of 50/1 was employed in all tests. Half-lives of TCE degradation at 10, 20 and 30 degrees C (pH 7) were 115.5, 35.0 and 5.5h, respectively. Maximum TCE degradation occurred at pH 7. Lowering system pH resulted in a greater decrease in TCE degradation rates than increasing system pH. Radical scavenging tests used to identify predominant radical species suggested that the sulfate radical (SO(4)(.-)) predominates under acidic conditions and the hydroxyl radical (.OH) predominates under basic conditions. In a side by side comparison of TCE degradation in a groundwater vs. unbuffered RO water it was demonstrated that when the system pH is buffered to near neutral pH conditions due to the presence of natural occurring groundwater constituents that the TCE degradation rate is higher than in unbuffered RO water where the system pH dropped from 5.9 to 2.8. The results of this study suggest that in a field application of ISCO, pH should be monitored and adjusted to near neutral if necessary.     

Mechanism of decolorization and degradation of CI Direct Red 23 by ozonation combined with sonolysis

The decolorization and degradation of CI Direct Red 23, which is suspected to be carcinogenic, were investigated using ozonation combined with sonolysis. The results showed that the combination of ozonation and sonolysis was a highly effective way to remove color from waste water. The operational parameters, namely concentration of the dye, pH, ozone dose and ultrasonic density, were investigated during the process. The decolorization of the dye followed pseudo-first-order kinetics. Increasing the initial concentration of Direct Red 23 led to a decreasing rate constant. The optimum pH for the reaction was 8.0, and both lower and higher pH decreased the removal rate. The effect of the ozone dose on the dye decolorization was much greater than that of the sonolysis density. Intermediates such as naphthalene-2-sulfonic acid, 1-naphthol, urea and acetamide were detected by gas chromatography coupled with mass spectrometry in the absence of pH buffer, while nitrate and sulfate ions and formic, acetic and oxalic acids were detected by ion chromatography. A tentative degradation pathway was proposed without any further quantitative analyses. During the degradation, all nitrogen atoms and phenyl groups of Direct Red 23 were degraded into urea, nitrate ion, nitrogen and formic, acetic and oxalic acids, etc.     

Citrobacter sp. CK3对活性红KN-3B的脱色反应动力学研究

采用脱色菌Citrobacter sp. CK3,以活性红KN-3B染料为处理对象,在厌氧批式反应条件下,系统考察了pH值,温度和染料浓度对脱色反应速度的影响;通过动力学模拟及反应过程中染料的UV-Vis扫描图分析,探讨了脱色反应机理。结果表明：Citrobacter sp. CK3对活性红KN-3B的脱色反应的适宜pH为7～9;脱色反应速度在温度为32℃时达到最大。染料初浓度从57 mg/L逐渐增大到458 mg/L时脱色率逐渐降低。脱色过程中染料的偶氮键发生断裂,脱色反应符合二级反应动力学。     

Bioaugmented sulfate reduction using enriched anaerobic microflora in the presence of zero valent iron

Biological sulfate reduction was evaluated in batch and continuous reactors that were inoculated with enriched microflora cultivated from sulfate laden medium. Heterotrophic sulfate-reducing bacteria (SRB) principally reduced the sulphate when the chemical oxygen demand was sufficient. The heterotrophic SRB in the enriched microflora could not efficiently reduce sulphate at T<33 °C and/or pH<6.0. However, when 200 mg L(-1) of zero valent iron (ZVI) was added to the reactor, the sulphate reduction rate was increased by 15% while the inhibition of the SRB activity occurred at T<25 °C or pH<4.5, broader than those noted for non-ZVI systems. In batch tests, the autotrophic SRB reduced 95% of 1500 mg L(-1) sulphate in <50h at 15 °C when the substrate was amended with 8 gL(-1) ZVI. In continuous up-flow anaerobic multiple bed reactor tests conducted to evaluate the remediation of sulphate in acid mine runoff, ZVI enhanced the activity of SRB, resulting in a 61% reduction of 20.8 gL(-1) sulphate when the reactor was operated at 25 °C and pH 2.6 with a hydraulic remain time of 96 h.     

Biodecolorization of the azo dye Reactive Red 2 by a halotolerant enrichment culture.

The decolorization of the azo dye Reactive Red 2 (RR2) under anoxic conditions was investigated using a mesophilic (35 degrees C) halotolerant enrichment culture capable of growth at 100 g/L sodium chloride (NaCl). Batch decolorization assays were conducted with the unacclimated halotolerant culture, and dye decolorization kinetics were determined as a function of the initial dye, biomass, carbon source, and an externally added oxidation-reduction mediator (anthraquinone-2,6-disulphonic acid) concentrations. The maximum biomass-normalized RR2 decolorization rate by the halotolerant enrichment culture under batch, anoxic incubation conditions was 26.8 mg dye/mg VSSxd. Although RR2 decolorization was inhibited at RR2 concentrations equal to and higher than 300 mg/L, the halotolerant culture achieved a 156-fold higher RR2 decolorization rate compared with a previously reported, biomass-normalized RR2 decolorization rate by a mixed mesophilic (35 degrees C) methanogenic culture in the absence of NaCl. Decolorization kinetics at inhibitory RR2 levels were described based on the Haldane model (Haldane, 1965). Five repetitive dyeing/decolorization cycles performed using the halotolerant culture and the same RR2 dyebath solution demonstrated the feasibility of biological renovation and reuse of commercial-strength spent reactive azo dyebaths.     

树脂固载纳米铁对偶氮染料直接湖蓝5B的脱色性能研究

以FeSO4和NaBH4水溶液为前驱溶剂,以聚苯乙烯型阳离子交换树脂为载体,制备了树脂固载的纳米铁,室温下用于对偶氮染料直接湖蓝5B水溶液进行脱色研究。研究结果发现,脱色反应遵循准一级反应动力学,在初始pH为3~10的范围内,反应进行14 m in时,50 mg/L的染料溶液脱色率均能达到83%以上。固载的纳米铁材料可多次重复利用,溶液中释放的铁离子浓度不超过0.1 mg/L。     

Biodegradation mechanisms and kinetics of azo dye 4BS by a microbial consortium

A microbial consortium consisting of a white-rot fungus 8-4* and a Pseudomonas 1-10 was isolated from wastewater treatment facilities of a local dyeing house by enrichment, using azo dye Direct Fast Scarlet 4BS as the sole source of carbon and energy, which had a high capacity for rapid decolorization of 4BS. To elucidate the decolorization mechanisms, decolorization of 4BS was compared between individual strains and the microbial consortium under different treatment processes. The microbial consortium showed a significant improvement on dye decolorization rates under either static or shaking culture, which might be attributed to the synergetic reaction of single strains. From the curve of COD values and the UV-visible spectra of 4BS solutions before and after decolorization cultivation with the microbial consortium, it was found that 4BS could be mineralized completely, and the results had been used for presuming the degrading pathway of 4BS. This study also examined the kinetics of 4BS decolorization by immobilized microbial consortium. The results demonstrated that the optimal decolorization activity was observed in pH range between four and 9, temperature range between 20 and 40 degrees C and the maximal specific decolorization rate occurred at 1,000 mg l(-1) of 4BS. The proliferation and distribution of microbial consortium were also microscopically observed, which further confirmed the decolorization mechanisms of 4BS.     

硫酸盐在偶氮染料厌氧生物脱色中的作用

以沼泽红假单胞菌W1为研究对象,考察了厌氧条件下硫酸盐还原对活性黑5(Reactive Black 5,RB5)和直接黄11(Direct Yellow 11,DY11)生物脱色的影响。结果表明,硫酸盐本身对2种染料脱色无明显影响,而硫酸盐的还原产物———硫化物能通过氧化还原介体使2种染料化学脱色,其脱色过程能在3 min内迅速完成。在无介体加入的情况下,硫化物能够通过RB5自身产生的介体加速RB5的脱色;而对于不能产生氧化还原介体的DY11,硫化物对其脱色无明显影响。硫化物经染料氧化后形成的硫单质能够被菌株W1重新转化为硫化物,继续还原染料。     

活性黑KN-B染料模拟废水电化学脱色

为进一步明确活性染料在可溶性阳极电化学体系中的脱色机理，以铝为牺牲阳极，不锈钢为阴极，在恒电流操作模式下，针对活性黑KN-B模拟废水，考察了电流密度、初始pH值、电解质种类及浓度、温度、染料浓度因素对染料脱色过程的影响。结果表明：(1)电流密度、电解液初始pH值、氯化钠电解质浓度、温度、染料浓度对染料溶液脱色效率影响显著，在一定实验条件下，染料溶液脱色率可达到88%；(2) 在不同pH的范围内，活性黑KN-B表现的脱色机理不同，pH 4～9为混凝与阴极还原脱色共同作用；pH＜4和＞9则表现为阴极还原脱色为主； (3) 氯化钠的加入在增强染料脱色的同时，也有助于芳环类物质的后续混凝去除。     

高铁酸盐对活性及分散染料的脱色研究

采用湿法制备了高铁酸钾(K₂FeO₄)氧化剂，研究了其对染料活性艳红X-3B(X-3B) 和分散蓝2BLN(2BLN)在不同pH条件下的脱色效果，并对Al₂ (SO₄)₃、K₂FeO₄及O₃对活性及分散染料的脱色效果进行了比较。结果表明：高铁酸钾对活性及分散染料的脱色效果明显， X-3B脱色率随pH的增加不断提高，2BLN脱色率在pH 6～10范围内无明显变化，在pH＝5时达到最大值。在X-3B及2BLN浓度同为100 mg／L，pH分别为10、5， K₂FeO₄浓度分别为100 mg／L和200 mg／L时，BLN及X-3B的脱色率分别达到92.3％和87.3％。在相同条件下，K₂FeO₄对活性艳红X-3B的脱色效果好于Al₂(SO₄)₃和O₃； 而K₂FeO₄对分散蓝2BLN的脱色效果虽比Al₂ (SO₄)₃稍差，但比臭氧的脱色效果要好。同时还研究了K₂FeO₄对活性及分散染料的脱色机理，结果表明： 高铁酸钾对X-3B的脱色依赖于K₂FeO₄的氧化作用，而对的2BLN的脱色则以絮凝为主。     

Biological decolorization of reactive anthraquinone and phthalocyanine dyes under various oxidation-reduction conditions.

The decolorization of two anthraquinone dyes (Reactive Blue 4 [RB4] and Reactive Blue 19 [RB19]) and two phthalocyanine dyes (Reactive Blue 7 [RB7] and Reactive Blue 21 [RB21]) was investigated at an initial dye concentration of 300 mg/L using an unacclimated, enrichment culture. The culture was fed a mixture of organic compounds and maintained initially under aerobic conditions, and then progressively developed anoxic/ anaerobic conditions. Biotransformation-related decolorization of the dyes did not take place under aerobic conditions, but use of the feed organic mixture and biomass production by the enrichment culture were not affected. Complete ammonia removal occurred in the control and all dye-amended cultures. The development and extent of nitrification were much lower in the latter cultures, in which ammonia removal via air stripping was the dominant mechanism. Prolonged incubation of the culture under anoxic/anaerobic conditions with multiple carbon source additions resulted in a high decolorization extent of anthraquinone dyes (over 84%) and only partial decolorization of phthalocyanine dyes (49 to 66%). Development of significant methanogenic activity took place in the control and, to a lesser extent, in the two phthalocyanine dye-amended cultures, but the anthraquinone dyes severely inhibited the development of methanogenic activity. The RB4 and RB19 decolorization was attributed to nonreversible, microbially mediated dye transformation(s), demonstrated by the accumulation of decolorization products with absorbance maxima in the 420- to 460-nm region. The decolorization of RB4 and RB19 followed Michaelis-Menten kinetics. At an initial dye concentration of 300 mg/L, the observed maximum decolorization rate per unit biomass was 9.1 and 37.5 mg dye/mg volatile suspended solids x day for the RB4 and RB19, respectively. Thus, partial decolorization of reactive phthalocyanine dyes and extensive biological decolorization of reactive anthraquinone dyes is feasible only under anoxic/anaerobic conditions.     

交联壳聚糖／Cu2O复合颗粒可见光催化脱色活性艳红

利用壳聚糖对金属离子的吸附和螯合作用，通过简单的液相沉淀一还原过程一步原位合成了交联壳聚糖／Cu2O复合粒子。x射线衍射（XRD）和红外（FT—IR）测试结果表明，壳聚糖与Cu2O纳米微粒能有效复合。以活性艳红X-3B溶液为模拟印染废水，采用Langmuir-Hinshelwood假一级方程模拟交联壳聚糖／Cu2O复合粒子光催化脱色反应的动力学行为，从动力学角度系统研究染料初始浓度、反应体系pH、催化剂用量和反应体系气氛等因素对复合粒子可见光催化脱色反应速率的影响。结果表明，当染料溶液浓度较低时，光催化过程可视为假一级反应。降低活性艳红X-3B初始浓度和pH，增加催化剂用量和反应体系的含O2量都可显著增加光解脱色反应速率常数。相同条件下，与纯Cu2O相比，交联壳聚糖／Cu2O复合粒子对X-3B呈现出更好的吸附性和更高的可见光催化活性。     

Copper complexation by dissolved organic matter and uncertainty assessment of their stability constants

The interaction of Cu with dissolved organic matter (DOM, extracted from an organic forest floor) was investigated and the resulting data was evaluated in terms of their uncertainty. The speciation of Cu over ‘free’ Cu (as analysed by diffusive gradients in thin films (DGT)), dissolved Cu–DOM complexes and precipitated Cu–DOM was determined as a function of pH (3.5, 4.0 and 4.5) and Cu/C ratio. The dissolved organically bound fraction was highest at pH 4.5, but this fraction decreased with increasing Cu/C ratio, which was observed for all pH levels. In the range of Cu/C=7×10⁻⁵–2.3×10⁻² (mol/mol) the precipitated fraction was very small. The speciation of both Al and Fe was not affected by increasing Cu concentrations. From a continuous distribution model using the Scatchard approach, we calculated the optimal fit and corresponding upper and lower 95% uncertainty bounds of the overall stability constants (K_o) with the shuffled complex evolution Metropolis (SCEM) algorithm. Although the optimal equation fitted the data very well, the uncertainty of the, according to literature, most reliable approach to establish stability constants, was still large. Accordingly, the usually reported intrinsic stability constants exhibited large uncertainty ranging from logK_i=6.0–7.1 (optimal 6.7) for pH 3.5, logK_i=6.5–7.1 (optimal 6.8) for pH 4.0, and logK_i=6.4–7.2 (optimal 6.8) for pH 4.5 and showed only little effect of pH.     

超强静磁场对染料脱色菌Escheriehia coli的acpD基因的影响

将大肠杆菌E.coli ATCC8739置于12.0 T超强静磁场(ultra-strong static magnetic field,SMF)中进行处理,获得了磁场处理0.5、1、2、4和8 h的菌株E.coli-SMFn(n=0.5、1、2、4、8)。在37℃、pH 7、静置的条件下,菌株对偶氮染料AR14(I.C.Acid Red 14)的脱色结果指出,当反应进行到4、6和8 h时,E.coli-SMF8的脱色效率分别为18%、55%和96%,远高于E.coli ATCC8739的3%、19%和50%,表明SMF作用显著地增强了菌株的脱色效率。基因组DNA提取、PCR扩增、分子克隆以及基因测序的实验结果进一步表明,全部6例E.coli ATCC8739菌株的偶氮还原酶基因(acpD)序列均与GenBank中报道的完全一致;而E.coli-SMF8菌株的acpD-SMF8核酸序列中缺失了第99位的胞嘧啶。该缺失突变不仅使acpD-SMF8的核酸序列与acpD的存在显著不同,同时得到了具新活性中心的偶氮还原酶AzoR-SMF8。这个新的活性中心具有更强的黄素(FMN)结合能力,因此使该酶与偶氮染料的亲和力大大增加,促进了脱色效率的提高。     

Oxidative stress response in dye degrading bacterium Lysinibacillus sp. RGS exposed to Reactive Orange 16, degradation of RO16 and evaluation of toxicity

Lysinibacillus sp. RGS degrades sulfonated azo dye Reactive Orange 16 (RO16) efficiently. Superoxide dismutase and catalase activity were tested to study the response of Lysinibacillus sp. RGS to the oxidative stress generated by RO16. The results demonstrated that oxidative stress enzymes not only protect the cell from oxidative stress but also has a probable role in decolorization along with an involvement of oxidoreductive enzymes. Formation of three different metabolites after degradation of RO16 has been confirmed by GC-MS analysis. FTIR analysis verified the degradation of functional groups of RO16, and HPTLC confirmed the removal of auxochrome group from the RO16 after degradation. Toxicity studies confirmed the genotoxic, cytotoxic, and phytotoxic nature of RO16 and the formation of less toxic products after the treatment of Lysinibacillus sp. RGS. Therefore, Lysinibacillus sp. RGS has a better perspective of bioremediation for textile wastewater treatment.     

亚铁羟基络合物还原转化水溶性偶氮染料

偶氮染料是印染工艺中应用最广泛的一类染料,目前染料废水脱色是污水处理难题。亚铁混凝处理染料废水过程中可能存在亚铁的还原作用,本实验制备了比溶解态亚铁更具还原反应活性的亚铁羟基络合物(ferrous hydroxycomplex,FHC),以5种不同类型的水溶性偶氮染料为目标污染物,研究FHC还原水溶性偶氮染料的脱色性能。实验结果表明,FHC对活性艳红X-3B、酸性大红GR和阳离子红X-GRL有较好的还原脱色效果,仅投加含铁89.6 mg/L的FHC,染料脱色率达到90%以上,继续增大FHC投加量可以完全脱色;中性枣红GRL的FHC还原脱色效果较差,需加入313.6 mg/L的FHC才能达到90%以上脱色率;134.4 mg/L的FHC能够将直接耐酸大红4BS完全脱色,但其脱色主要以混凝沉淀为主;溶液pH对FHC的还原性能产生重要影响,FHC还原染料脱色的适宜的pH值范围为4～10。该研究为亲水性染料脱色提供了一种新的技术,也为FHC运用于印染废水脱色提供了理论基础。     

Degradation and decolorization of a biodegradable-resistant polymeric dye by chelator-mediated Fenton reactions

Chelator-mediated Fenton reactions (CMFRs) were used to decolorize a biodegradable-resistant polymeric dye (Poly R-478). Screening of different iron chelators was performed on Fe(3+)-reduction activity. All chelators showed Fe(3+)-reduction activity over a wide range of pH (2-7) and each mol of catecholate chelators (3,4-dihydroxiphenilacetic acid--DOPAC and 2,3-dihydroxibenzoic acid--DHBA) reduced about 5-6 moles of Fe(3+) whereas hydroxamate chelators (acetohydroxamic acid-AHA and desferrioxamine B-DFB) reduced Fe(3+) stoichiometrically. The most effective decolorization of Poly R-478 was achieved by CMFR using catecholate chelators. In addition, a 2(4) factorial design was performed with the aim of evaluating the effects of the variables considered in this study (pH, [DOPAC], [Fe(3+)] and [H(2)O(2)]) and optimizing the dye decolorization, using response surface methodology. Statistical analysis of results showed that, in the range studied, except for Fe(3+), all variables have a significant effect on dye decolorization. A second-order model is proposed to represent the Poly R-478 decolorization. At optimum conditions, complete decolorization of the dye (degradation of the chromophoric group) and also complete chemical degradation of the dye was observed.     

Kinetics of the oxidation of sucralose and related carbohydrates by ferrate(VI)

The kinetics of the oxidation of sucralose, an emerging contaminant, and related monosaccharides and disaccharides by ferrate(VI) (Fe(VI)) were studied as a function of pH (6.5-10.1) at 25°C. Reducing sugars (glucose, fructose, and maltose) reacted faster with Fe(VI) than did the non-reducing sugar sucrose or its chlorinated derivative, sucralose. Second-order rate constants of the reactions of Fe(VI) with sucralose and disaccharides decreased with an increase in pH. The pH dependence was modeled by considering the reactivity of species of Fe(VI), (HFeO(4)(-) and FeO(4)(2-)) with the studied substrates. Second-order rate constants for the reaction of Fe(VI) with monosaccharides displayed an unusual variation with pH and were explained by considering the involvement of hydroxide in catalyzing the ring opening of the cyclic form of the carbohydrate at increased pH. The rate constants for the reactions of carbohydrates with Fe(VI) were compared with those for other oxidant species used in water treatment and were briefly discussed.