Investigation of 1,4-dioxane originating from incineration residues produced by incineration of municipal solid waste

As a groundwater contaminant, 1,4-dioxane is of considerable concern because of its toxicity, refractory nature to degradation, and rapid migration within an aquifer. Although landfill leachate has been reported to contain significant levels of 1,4-dioxane, the origin of 1,4-dioxane in leachate has not been clarified until now. In this study, the origins of 1,4-dioxane in landfill leachate were investigated at 38 landfill sites and three incineration plants in Japan. Extremely high levels of 1,4-dioxane 89 and 340 microg l(-1), were detected in leachate from two of the landfill sites sampled. Assessments of leachate and measurement of 1,4-dioxane in incineration residues revealed the most likely source of 1,4-dioxane in the leachate to be the fly ash produced by municipal solid waste incinerators. Effective removal of 1,4-dioxane in leachate from fly ash was achieved using heating dechlorination systems. Rapid leaching of 1,4-dioxane observed from fly ash in a sequential batch extraction indicated that the incorporation of a waste washing process could also be effective for the removal of 1,4-dioxane in fly ash.     

垃圾焚烧飞灰综合利用研究进展

焚烧处理是解决日益增长生活垃圾的有效方法。垃圾焚烧产生的飞灰因含有大量的重金属等污染物而属危险废物 ,目前常采用的处理方法是填埋。本文就垃圾飞灰的综合利用研究现状进行了论述。从环境和技术的角度看 ,垃圾飞灰的预处理、水泥固化和玻璃化是目前飞灰综合利用的主要研究方向     

村镇小型生活垃圾热处理炉底渣的理化特性

小型垃圾热处理设备可实现就地处置,节约运输成本,目前在中国山区、丘陵地带的村镇得到广泛应用.为了解村镇小型生活垃圾热处理炉底渣的理化特性及其影响因素,对中国云南、贵州、安徽村镇实际运行的小型生活垃圾热处理设备产生的底渣进行取样,分析其热灼减率、物理组成、化学组成、晶相组成、重金属含量和浸出特性,探讨处理工艺、地域及季节...     

A pilot and field investigation on mobility of PCDDs/PCDFs in landfill site with municipal solid waste incineration residue

A field investigation by boring was carried out in a landfill site primarily with municipal solid waste incineration residue. From the collected core samples, vertical profiles of homologous content of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs) in the landfill layer were traced and the behavior of PCDDs/PCDFs was examined. In addition, a pilot-scale study was conducted on the PCDDs/PCDFs leached from incineration fly ash and the treated one using large landfill simulation columns (lysimeters) and the leaching behavior of PCDDs/PCDFs was examined. As a result, it was found that the coexistence of dissolved coloring constituents (DCCs), which might be composed of constituents like dissolved humic matters having strong affinity for hydrophobic organic pollutants, could enhance the leachability of PCDDs/PCDFs, thus contributing to the vertical movement and leaching behavior of PCDDs/PCDFs in the landfill layers of the incineration residue. Moreover, it is highly probable that DCCs derive from the unburned carbon in the bottom ash mixed and buried with the fly ash containing a high content of PCDDs/PCDFs.     

Characteristics and management modes of domestic waste in rural areas of developing countries: a case study of China

A huge accumulation of domestic waste has caused serious environmental contamination in rural areas of developing countries (RADIC). The characteristics and management of domestic waste are carefully discussed, based on field surveys and a literature review. The results indicate that the generation in most of RADIC is less than the median of 0.521 kg day⁻¹ per capita in China, and much smaller than in rural areas of developed countries (RADEC). Organic waste and inert waste with an accumulative mass percentage of 72.31% are dominant components of domestic waste in the rural areas of China. There are trends of increasing amounts of kitchen waste, paper/cardboard, and plastic/rubber and a decreasing trend of ash waste. The RADIC composition of domestic waste had a high content of organic waste and a low content of recyclable waste compared to the RADEC. Domestic waste has good compressibility and a light bulk density ranging from 40 to 650 kg m⁻³. The moisture, ash, combustible, and calorific values of domestic waste were 53.31%, 18.03%, 28.67%, and 5368 kJ kg⁻¹, respectively. The domestic waste has an abundance of nutrients including organic matter (39.05%), nitrogen (1.02%), phosphorus (0.50%), and potassium (1.42%). In RADIC, domestic waste can be used as an agricultural manure only after it has been collected and sorted for the potential risk of heavy metal accumulation. Based on these characteristics of domestic waste and the different situations of rural areas, four waste management modes including centralized treatment, decentralized treatment, group treatment, and mobile treatment are designed and discussed.

     

天津市文明生态村生活垃圾处理方案优选

根据天津市文明生态村生活垃圾的特点和组成成分,以垃圾的分类收集和分类处理为前提,采用费用-效益分析法和层次分析法,对填埋、堆肥和焚烧处理方案分别进行费用-效益分析和经济、技术、环境、政策综合分析。结果表明,堆肥和焚烧的费用-效益分析得分为0.96和0.786,填埋不产生效益;堆肥、焚烧和填埋的层次分析法得分为7.74、4.28和5.45,堆肥方案的得分最高,其次为填埋,天津市文明生态村生活垃圾宜采用堆肥+填埋处理方案。     

Limitations of the toxicity characteristic leaching procedure for providing a conservative estimate of landfilled municipal solid waste incineration ash leaching

Limitations of the toxicity characteristic leaching procedure (TCLP) for simulating pollutant leaching from wastes disposed of in full-scale landfills are well understood in the waste management profession; the TCLP solution has a lower pH and greater organic acid content than typical landfill leachate. The TCLP serves its intended regulatory objective, however, as long as a conservative estimate of leaching is provided. Here, we examine TCLP’s ability to represent worst-case leaching conditions for monofilled municipal solid waste incineration (MSWI) ash. A critical examination of TCLP’s applicability to MSWI ash is especially relevant, as ash management at MSWI facilities often centers on passing TCLP, regardless of environmental risk posed by the ash or its recyclability. Multiple batch leaching tests were conducted on different MSWI ash streams: mixed ash, fly ash, and different size fractions of bottom ash. Batch-test results were compared with leachate simulating MSWI ash monofills. The TCLP did not consistently provide the most conservative estimate of leaching, supporting the need to consider alternative methodologies in future regulatory development.

Implications: This paper analyzes the existing hazardous waste regulatory testing requirement for municipal solid waste incinerator (MSWI) ash management to evaluate whether the TCLP serves its intended purpose in providing the most conservative estimate of landfilled MSWI ash. The results will serve as guidance and motivation for policy makers and the regulatory community to reevaluate the TCLP’s application for characterizing MSWI ash leaching in certain disposal scenarios and could promote consideration of alternative testing procedures based upon results of this study. This study serves to promote representative and accurate quantification of leaching risk from MSWI ash.     

Changes in PCDD/PCDF formation processes during instationary phases of combustor operation--exemplified by the use of Cl4DD isomer patterns

In this paper results of various measurement campaigns at different municipal waste incineration (MWI) plants concerning the change of the PCDD/PCDF isomer distribution in the crude gas during transiently impaired combustion conditions are presented. The focus is on the Cl4DD isomer distributions exemplarily for all other homologue groups to demonstrate the change in PCDD/PCDF formation mechanism at transient combustion conditions. Additionally to crude gas samples, at one plant filter and boiler ash were investigated simultaneously to determine if there is any difference in the isomer distribution between the matrices. For the ash from an electrostatic precipitator (ESP ash), the boiler ash and the corresponding crude gas sample, nearly identical changes in the Cl4DD isomer distribution under transient combustion conditions in relation to the normal operation process could be detected. By comparing the Cl4DD isomer distributions from different incineration plants (two municipal waste incinerators and one little incinerator burning wood chips for heating domestic household) under transient combustion conditions, in all cases the 1,3,6,8- and 1,3,7,9-Cl4DD were dominating the isomer distribution, whereas under normal operation other isomers were predominant. Obviously PCDD/PCDF formation mechanisms under transient combustion conditions are independent from the type of incinerator and of the burned fuel, respectively. Data sets were analyzed with respect to the possible reaction mechanism via chlorophenols and a good correlation of 2,4,6-trichlorophenol during the second phase of a start-up process and during a CO experiment was found. To get more detailed information about possible formation mechanisms, at one plant the dependence of the PCDD/PCDF isomer distribution on the different matrices was studied. Separate analysis of fly ash collected at the boiler exit, subsequent gas phase, ESP ash and boiler ash under normal operation conditions showed that, apart from the fly ash, the Cl4DD isomer distributions are nearly the same in the different matrices. Surprisingly, the Cl4DD isomer distribution of the fly ash was more similar to the distributions found under transient combustion conditions.     

Geotechnical engineering properties of incinerator ash mixes

The incineration of solid waste produces large quantities of bottom and fly ash. Landfilling has been the primary mode of disposal of these waste materials. Shortage in landfill space and the high cost of treatment have, however, prompted the search for alternative uses of these waste materials. This study presents an experimental program that was conducted to determine the engineering properties of incinerator ash mixes for use as construction materials. Incinerator ash mixes were tested as received and around optimum compacted conditions. Compaction curves, shear strength, and permeability values of fly ash, bottom ash, and their various blends were investigated. Bottom ash tends to achieve maximum dry density at much lower water content than does fly ash. The mixes displayed a change in their cohesion and friction angle values when one of the two mix components was altered or as a result of the addition of water. The permeability of bottom ash is quite comparable to that of sand. The permeability of fly ash lies in the range of those values obtained for silts and clays. A 100% bottom ash compacted at the optimum water content has a lower density value and yields a higher friction angle and cohesion values than most construction fills. This would encourage the use of bottom ash as a fill or embankment material because free drainage of water will prevent the buildup of pore water pressures.     

苏州市生活垃圾两种处置方法的生命周期影响评价

采用生命周期评价的方法，比较了苏州市垃圾填埋和垃圾焚烧2种处置方法对环境的影响。研究的系统范围主要包括垃圾收集、垃圾运输、垃圾填埋或焚烧以及发电等几个部分。采用收集的垃圾组分数据，利用IPCC推荐的模型等，计算了垃圾填埋和垃圾焚烧时CO₂等气体污染物的排放量。根据对垃圾渗滤液的实测数据，计算了水污染物的排放量。环境影响评价采用日本开发的AIST-LCA Ver4计算机软件进行。计算结果表明：垃圾填埋的生态币值要大得多，可见垃圾焚烧对环境的影响比垃圾填埋的影响要小。所获得的结论较为客观地反映了对环境的影响，可以作为中国城市垃圾处置决策的参考依据。     

Geotechnical Engineering Properties of Incinerator Ash Mixes

Abstract

The incineration of solid waste produces large quantities of bottom and fly ash. Landfilling has been the primary mode of disposal of these waste materials. Shortage in landfill space and the high cost of treatment have, however, prompted the search for alternative uses of these waste materials. This study presents an experimental program that was conducted to determine the engineering properties of incinerator ash mixes for use as construction materials. Incinerator ash mixes were tested as received and around optimum compacted conditions. Compaction curves, shear strength, and permeability values of fly ash, bottom ash, and their various blends were investigated. Bottom ash tends to achieve maximum dry density at much lower water content than does fly ash. The mixes displayed a change in their cohesion and friction angle values when one of the two mix components was altered or as a result of the addition of water. The permeability of bottom ash is quite comparable to that of sand. The permeability of fly ash lies in the range of those values obtained for silts and clays. A 100% bottom ash compacted at the optimum water content has a lower density value and yields a higher friction angle and cohesion values than most construction fills. This would encourage the use of bottom ash as a fill or embankment material because free drainage of water will prevent the buildup of pore water pressures.     

A microscopic and quantitative analysis on the separation of chloride ion by fly ash washing: Effect of liquid-to-solid ratio,washing time and temperature

Environmental Science and Pollution Research - In order to understand the removal characteristics of Cl? (chloride ion) in the fly ash from municipal solid waste incineration, so as to...     

垃圾焚烧底灰固化污水厂污泥的岩土工程性质实验

对污水处理厂污泥采用垃圾焚烧底灰进行固化处理,分别测试不同掺量和不同养护龄期时固化体的岩土工程性质,通过测试发现,固化体重度基本位于11～13 kN/m3之间,与垃圾焚烧底灰的重度相近;固化体含水率随着垃圾焚烧底灰掺量的增大而急剧减小;抗剪强度指标和无侧限抗压强度随垃圾焚烧底灰的掺量增加和养护龄期的增长而增大,其内摩擦角位于10°～30°之间。建立的固化强度预测模型,可对不同掺量和龄期的固化污泥强度进行预测。     

Characteristics of volatile compound emission and odor pollution from municipal solid waste treating/disposal facilities of a city in Eastern China

Transfer station, incineration plant, and landfill site made up the major parts of municipal solid waste disposal system of S city in Eastern China. Characteristics of volatile compounds (VCs) and odor pollution of each facility were investigated from a systematic perspective. Also major index related to odor pollution, i.e., species and concentration of VCs, olfactory odor concentration, and theoretic odor concentration, was quantified. Oxygenated compounds and hydrocarbons were the most abundant VCs in the three facilities. Different chemical species were quantified, and the following average concentrations were obtained: transfer station, 54 VCs, 2472.47 μg/m³; incineration plant, 75 VCs, 33,129.25 μg/m³; and landfill site, 71 VCs, 1694.33 μg/m³. Furthermore, the average olfactory odor concentrations were 20,388.80; 50,677.50; and 4951.17, respectively. The highest odor nuisance was detected in the waste tipping port of the incineration plant. A positive correlation between the olfactory and chemical odor concentrations was found with R ² = 0.918 (n = 15, P < 0.01). The result shows odor pollution risk transfer from landfill to incineration plant when adopting thermal technology to deal with the non-source-separated waste. Strong attention thus needs to be paid on the enclosed systems in incineration plant to avoid any accidental odor emission.

     

Effect of dissolved humic matters on the leachability of PCDD/F from fly ash--laboratory experiment using Aldrich humic acid

The effect of dissolved humic matters (DHM) on the leachability of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) in fly ash was studied theoretically and in laboratorial condition to verify the previous results for pilot and field experiment of incineration residues landfill. In theoretical review, it was shown that DHM could influence the actual solubility and leachability of PCDD/F. The higher concentration of DHM showed the higher leachability of PCDD/F. In the leaching test, three different DHM concentrations and pHs of solutions were adopted to fly ash samples imaging the various characteristics of municipal solid waste leachate. It was proved experimentally that the leachability of PCDD/F increased with increasing DHM concentration in all pH conditions. The highest leachability was shown at the highest pH. Isomer distribution patterns of PCDD/F in all leachates were similar in all pH conditions. It backed up the distribution theory of PCDD/F between DHM and water.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Emission inventory for greenhouse gases in the City of Barcelona, 1987–1996

Emissions of greenhouse gases for the City of Barcelona are estimated for the period 1987–1994. The sources considered are: public and private transportation; industrial, commercial and domestic activities; and municipal solid waste disposal. The results show that the main source of CO₂ emissions in Barcelona is private vehicle transportation, which accounts, as an average for the period studied, for 35% of total emissions. The second most important source is the municipal solid waste landfill facility of the city (24% of total emissions). The percentages for the remaining sources under consideration were: 14% electricity, 12% natural gas, 5% incineration, and 3% liquefied petroleum gases. However, the values for CO₂ emissions per inhabitant over the period studied are lower than those for any other industrialized city available for comparison. This is closely related to the high percentage of electricity generation from nuclear power stations and hydro power facilities, and also to the extensive use of natural gas for domestic uses.     

垃圾焚烧飞灰浸出特性及固化试验的研究

垃圾焚烧飞灰残留有重金属元素和二恶英等物质而被认为是危险废物,必须对之进行稳定化处理.通过试验研究分析了国内首家自主开发成功的广东省东莞市某回转窑垃圾焚烧发电厂垃圾焚烧飞灰的化学成分及矿物组成,研究了飞灰的浸出毒性,考察了水泥固化焚烧飞灰的效果,并与熔融/玻璃固化进行了比较.研究表明,该焚烧飞灰中重金属Cd的浸出毒性严重超标,并且随pH值的减小而增大,水泥固化效果随龄期的增大而更加显著.熔融/玻璃固化的效果优于水泥固化,但其经济性有待提高.     

Rural domestic waste management in Zhejiang Province,China: Characteristics,current practices,and an improved strategy

Lack of access to adequate sanitation facilities has serious health implications for rural dwellers and can degrade the ecosystems. This study offers a systemantic and quantitative overview of historical data on rural domestic waste (RDW) production and past and current management practices in a prototype region in China, where rural areas are undergoing rapid urbanization and are confronted with great environmental challenges associated with poor RDW management practices. The results indicate that RDW is characterized with a large fraction of kitchen waste (42.9%) and high water content (53.4%). The RDW generation (RDWG) per capita between 2012 and 2020 is estimated to increase from 0.68 to 1.01 kg/d-cap. The Hill 1 model is able to adequately simulate/project the population growth in a rural area from 1993 to 2020. The annual RDWG in the region is estimated to double from 6,033,000 tons/year in 2008 to 12,030,000 tons/year by 2020. By comparing three RDW management scenarios based on the life-cycle inventory approach and cost–benefit analysis, it is strongly recommended that the present Scenario 2 (sanitary landfill treatment) be upgraded to Scenario 3 (source separation followed by composting and landfill of RDW) to significantly reduce the ecological footprint and to improve the cost-effectiveness and long-term sustainability.

Implications:?Rural domestic waste (RDW) is affecting 720 million people in China and more than 3221 million people worldwide. Consequently, handling and disposal of RDW have serious health implications to rural dwellers and the ecosystems. This study offers a systemantic and quantitative overview and analysis of historical data on RDW production and management practices in a prototype region in China, which is confronted with great environmental challenges associated with RDW. Then we predict future production of RDW and propose a sustainable RDW management strategy, which holds the promise of greatly mitigating the mounting environmental pressure associated with RDW and provides science-based guidance for decision makers and practitioners for assuring rapid yet “green” economic development.     

垃圾焚烧重金属迁移特性及其影响因素

综述了城市固体垃圾(MSW)焚烧过程中的Hg、Cd、Pb、Cu、Zn、As和Cr等几种主要重金属污染源在焚烧过程中的迁移特性及其主要影响因素。将重金属在焚烧过程中的迁变归结为:蒸发、气相和表面反应、冷凝成核团聚和飞灰吸附等4个主要过程;而垃圾中重金属的初始浓度、原始垃圾的基体盐分(如A l、S i和K、Na等的存在形式)、垃圾中的C l(PVC和NaC l)和S的含量、垃圾的含水量以及焚烧过程中的运行参数(温度、滞留时间、氧化-还原气氛)等都会对焚烧过程的迁移规律产生影响。