非离子型聚丙烯酰胺絮凝剂的制备及其絮凝性能

以丙烯酰胺（AM）和烷基酚聚醚（APAP）为单体，采用反相乳液聚合法制备了流动性好的非离子型聚丙烯酰胺絮凝剂（PAM-APAP）。考察了乳化剂和引发剂的种类、单体总质量分数、单体配比和反应温度等因素对聚合反应的影响。实验结果表明，制备PAM-APAP的最佳工艺条件为：单体总质量分数35%、m（AM）∶m（APAP）=9.0∶1.0、Span80+Tween80复配乳化剂加入量为油水总质量的7%、m（Span80）∶m（Tween80）=7.0∶1.5、V50加入量为单体总质量的1.5‰、反应温度50℃。PAM-APAP具有较好的絮凝效果，与其他絮凝剂相比用量较少，在加入量为100mg/L时，对聚合物驱油中产生的含聚合物污水的浊度去除率为87.9%，去油率为89.5%，且絮体不黏壁。     

阳离子淀粉-丙烯酰胺接枝共聚物絮凝剂的制备及其絮凝性能

研究了阳离子淀粉与丙烯酰胺接枝共聚反应制备阳离子型絮凝剂的工艺，并用硅藻土悬浊液及实际水样对产物的絮凝性能进行了考察。其最佳合成条件：阳离子淀粉与丙烯酰胺的质量比为1：4，引发剂加入量为丙烯酰胺质量的0．1％，反应温度50℃，反应时间3h。絮凝效果实验中，接枝共聚物絮凝剂的最佳加入量为4mg／L。与阳离子淀粉和阳离子聚丙烯酰胺絮凝剂相比，接枝共聚物絮凝剂对渭河水及造纸网下白水的絮凝效果更好。     

丙烯酸酯类高吸油树脂的合成及其吸附性能

采用悬浮聚合法,以甲基丙烯酸甲酯(MMA)和丙烯酸丁酯(BA)为单体、二乙烯苯(DVB)为交联剂、过氧化苯甲酰(BPO)为引发剂,合成了一种丙烯酸酯类高吸油树脂。实验结果表明,在m(MMA)∶m(BA)=0.5、DVB加入量为0.8%、BPO加入量为1.2%的最佳条件下,树脂对氯仿的吸油率可达30.6 g/g,对氯仿、柴油、甲苯、废机油、花生油、丙酮等有机溶剂和油品的保油率可达90.0%以上。     

阳离子聚丙烯酰胺-TiO2复配絮凝剂的合成及性能

以甲基丙烯酰氧乙基三甲基氯化铵(DMC)和丙烯酰胺(AM)为单体,K2S2O8-NaHSO3为引发剂,采用水溶液聚合法合成了阳离子聚丙烯酰胺P(DMC-AM),将表面处理后的纳米TiO2与P(DMC-AM)复配,得到P(DMC-AM)-TiO2复配絮凝剂.考察了原料配比、反应条件对P(DMC-AM)黏度的影响,结果表明:在m(DMC):m(AM)=0.18、引发剂加入量为0.5%(质量分数,下同)、聚合反应时间3 h、聚合溶液pH=4.0条件下,P(DMC-AM)絮凝剂的特性黏度最佳;纳米TiO2加入量为5%时,复配絮凝剂对酸性黑10B染料模拟废水的脱色性能最好.     

微波辐射下改性壳聚糖的制备及其絮凝性能

采用微波辐射法合成了壳聚糖-丙烯酰胺接枝共聚物。通过傅立叶变换红外光谱(FTIR)谱图对比分析表明,丙烯酰胺成功地接枝到壳聚糖上,发生了接枝共聚反应;产物的热重-差热(TG-DSC)谱图表明,壳聚糖-丙烯酰胺接枝共聚物的热稳定性比壳聚糖差。壳聚糖-丙烯酰胺接枝共聚物作为絮凝剂处理高岭土悬浊液的最佳条件为:絮凝剂加入量4.0 mg/L,沉降时间20 min,溶液pH 7。处理印染废水时,与壳聚糖相比,壳聚糖-丙烯酰胺接枝共聚物加入量较少而COD去除效果较好。在废水pH为7、絮凝剂加入量为100 mg/L、沉降时间为20 min的条件下,壳聚糖-丙烯酰胺接枝共聚物对废水COD去除率达41.55%。     

含氟改性聚丙烯酰胺絮凝剂的合成及其絮凝性能

以全氟辛基乙基丙烯酸十二氟庚酯(PFMA)为疏水单体,与丙烯酰胺(AM)、二烯丙基二甲基氯化铵(DMDAAC)通过自由基胶束共聚法制得含氟改性聚丙烯酰胺(FPAD)絮凝剂。最佳聚合反应工艺条件:PFMA质量分数为0.3%,引发剂质量分数为0.3%,DMDAAC质量分数为15%,共聚反应温度为50℃。用FPAD处理初始透光率为20%、初始COD为282mg/L的废水,当FPAD加入量为15mg/L、絮凝体系pH为6时,废水透光率最高,可达98.7%;pH为6～9时,废水透光率和COD去除率均较高。     

高氯离子、低COD废水中COD的测定

建立了适用于高氯离子、低COD废水中COD的重铬酸钾测定方法。分别采用甘油、二氯丙醇、β,β′-二氯异丙醚和氯化钙配制模拟高氯废水,考察了氧化剂重铬酸钾溶液浓度、掩蔽剂加入量(以m(HgSO_4)∶m(Cl~-)表示)对测定效果的影响。实验结果表明:以低浓度(0.05 mol/L)重铬酸钾溶液为氧化剂时,测定数据波动范围小,相对误差也低(-1.4%~+0.4%);对于高氯低COD废水的COD测定,当COD大于100 mg/L时按m(HgSO_4)∶m(Cl~-)=10∶1加入硫酸汞掩蔽剂,当COD小于100 mg/L时按m(HgSO_4)∶m(Cl~-)=20∶1加入硫酸汞掩蔽剂,并采用浓度为0.05 mol/L的重铬酸钾溶液作为氧化剂,能较好地消除氯离子对COD测定的干扰,相对误差在5%以内;将优化后的测定条件应用于实际环氧氯丙烷生产废水COD的测定,重现性良好,当m(HgSO_4)∶m(Cl-)分别为10∶1和20∶1时,相对误差分别为+3.3%和+2.9%,COD平均回收率分别为103.4%和102.9%。     

水合肼改性淀粉去除废水中的重金属离子

以木薯淀粉为原料、硝酸铈铵为引发剂,合成丙烯酸甲酯接枝淀粉;用水合肼对其进行改性,合成了具有氨基功能团的改性淀粉。将改性淀粉用于对多种单一重金属离子和混合重金属离子的去除。在混合重金属离子溶液中,在室温、改性淀粉加入量为7.0g/L、重金属离子质量浓度为30mg/L、反应时间为120min的条件下,混合液pH为3～7时,改性淀粉对Cu2+、Pb2+、Cd2+和Ni2+的去除率均达99.9%以上;混合液pH为4时,改性淀粉对Cr6+的去除率达73.2%。     

两性聚丙烯酰胺的制备及其絮凝性能

开发了一种对非离子聚丙烯酰胺进行改性制备两性聚丙烯酰胺(APAM)絮凝剂的新方法。以硅藻土悬浮液为絮凝对象,考察了改性反应中影响APAM絮凝效果的因素。结果表明,采用无水乙酸与三甲胺、环氧氯丙烷合成季胺盐型阳离子剂的方法优于采用盐酸的方法;在10mL质量分数为10%、相对分子质量为3×106的非离子型聚丙烯酰胺水溶液中加入8mL浓度为2.6mol/L的阳离子剂,同时控制V(NaOH)∶V(NaClO)为0.44,改性得到的APAM絮凝性能最佳,在pH3～9的较宽范围内对硅藻土悬浮液有较好的絮凝效果。在pH为3、APAM加入量为1.8mg/L时,硅藻土悬浮液的絮凝率可达100%。     

疏水改性阳离子聚丙烯酰胺絮凝剂的制备及其絮凝性能

通过水溶液共聚合法,以丙烯酰胺(AM)、丙烯酰氧乙基三甲基氯化铵(DAC)和2-乙烯基吡啶(2-VP)为共聚单体合成了疏水改性阳离子聚丙烯酰胺P(AM-DAC-2VP),并用红外光谱仪和核磁共振光谱仪对其结构进行了表征。实验结果表明:当w(2-VP)为1.0%、w(DAC)为30%、活性污泥pH为5、P(AM-DAC-2VP)加入量为25mg/L时,P(AM-DAC-2VP)对本实验的活性污泥絮凝能力最强,上清液透光率为92.1%;P(AM-DAC-2VP)比同条件下制备的阳离子聚丙烯酰胺P(AM-DAC)具有更好的絮凝效果。     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％；靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.