Removal of dissolved organic matter in municipal effluent with ozonation, slow sand filtration and nanofiltration as high quality pre-treatment option for artificial groundwater recharge

In the paper the combination process of ozonation, slow sand filtration (SSF) and nanofiltration (NF) was investigated with respect to dissolved organic matter (DOM) removal as high quality pre-treatment option for artificial groundwater recharge. With the help of ozonation leading to breakdown of the large organic molecules, SSF preferentially removes soluble microbial by-product-like substances and DOM with molecular weight (MW) less than 1.0 kDa. NF, however, removes aromatic, humic acid-like and fulvic acid-like substances efficiently and specially removes DOM with MW above 1.0 kDa. The residual DOM of the membrane permeate is dominated by small organics with MW 500 Da, which can be further reduced by the aquifer treatment, despite of the very low concentration. Consequently, the O₃/SSF/NF system offers a complementary process in DOM removal. Dissolved organic carbon (DOC) and trihalomethane formation potential (THMFP) can be reduced from 6.5 ± 1.1 to 0.7 ± 0.3 mg L⁻¹ and from 267 ± 24 to 52 ± 6 μg L⁻¹, respectively. The very low DOC concentration of 0.6 ± 0.2 mg L⁻¹ and THMFP of 44 ± 4 μg L⁻¹ can be reached after the aquifer treatment.     

Assessment of fates of estrogens in wastewater and sludge from various types of wastewater treatment plants

We measured five estrogens in the wastewater samples from the municipal wastewater treatment plants (M-WWTPs), livestock wastewater treatment plants (L-WWTPs), hospital WWTPs (H-WWTPs) and pharmaceutical manufacture WWTPs (P-WWTPs) in Korea. The L-WWTPs showed the highest total concentration (0.195-10.4 μg L⁻¹) of estrogens in the influents, followed by the M-WWTPs (0.028-1.15 μg L⁻¹), H-WWTPs (0.068-0.130 μg L⁻¹) and P-WWTPs (0.015-0.070 μg L⁻¹). Like the influents, the L-WWTPs (0.003-0.729 μg L⁻¹) and the M-WWTPs (0.001-0.299 μg L⁻¹) also showed higher total concentration of estrogens in the effluents than the H-WWTPs (0.002-0.021 μg L⁻¹) and P-WWTPs (0.011 μg L⁻¹ in one sample). The L-WWTPs (37.5-543 μg kg⁻¹, dry weight) showed higher total concentrations in sludge than the M-WWTPs (3.16-444 μg kg⁻¹, dry weight) like the wastewater. The distribution of estrogens in the WWTPs may be affected by their metabolism in the human body, their transition through biological treatment processes, and their usage for livestock growth. Unlike the concentration results, the daily loads of estrogens from the M-WWTPs were the highest, which is related to the high capacities of WWTPs.     

Contamination of nonylphenolic compounds in creek water, wastewater treatment plant effluents, and sediments from Lake Shihwa and vicinity, Korea: comparison with fecal pollution

Nonylphenolic compounds (NPs), coprostanol (COP), and cholestanol, major contaminants in industrial and domestic wastewaters, were analyzed in creek water, wastewater treatment plant (WWTP) effluent, and sediment samples from artificial Lake Shihwa and its vicinity, one of the most industrialized regions in Korea. We also determined mass discharge of NPs and COP, a fecal sterol, into the lake, to understand the linkage between discharge and sediment contamination. Total NP (the sum of nonylphenol, and nonylphenol mono- and di-ethoxylates) were 0.32-875 μg L⁻¹ in creeks, 0.61-87.0 μg L⁻¹ in WWTP effluents, and 29.3-230 μg g⁻¹ TOC in sediments. Concentrations of COP were 0.09-19.0 μg L⁻¹ in creeks, 0.11-44.0 μg L⁻¹ in WWTP effluents, and 2.51-438 μg g⁻¹ TOC in sediments. The spatial distributions of NPs in creeks and sediments from the inshore region were different from those of COP, suggesting that Lake Shihwa contamination patterns from industrial effluents differ from those from domestic effluents. The mass discharge from the combined outfall of the WWTPs, located in the offshore region, was 2.27 kg d⁻¹ for NPs and 1.00 kg d⁻¹ for COP, accounting for 91% and 95% of the total discharge into Lake Shihwa, respectively. The highest concentrations of NPs and COP in sediments were found in samples at sites near the submarine outfall of the WWTPs, indicating that the submarine outfall is an important point source of wastewater pollution in Lake Shihwa.     

Leaching of zinc from tire wear particles under simulated estuarine conditions

Tire wear particles (TWP) abraded from end-of-life passenger car tires have been added at a concentration of 1 g L⁻¹ to river water, sea water and mixtures thereof in order to examine the chemical controls on the leaching of Zn from the rubber matrix. Results of time-dependent experiments conducted over a period of 5 days were consistent with a diffusion controlled leaching mechanism with rate constants of about 0.04 mg L⁻¹ h^−1/2 in river water and between about 0.02 and 0.03 mg L⁻¹ h^−1/2 in sea water. Additional experiments revealed a reduction in Zn dissolution with both increasing salinity and pH and enhancement of leaching in the presence of fluorescent light compared with dark conditions. In corresponding experiments conducted in the presence of a fixed quantity (0.8 g L⁻¹) of clean, fractionated estuarine sediment, aqueous Zn concentrations were reduced by at least an order of magnitude. Increasing the quantity of sediment resulted in a progressive reduction in Zn concentration until an apparent equilibrium was achieved, with partition coefficients defining the sediment-water distribution of Zn of about 550 mL g⁻¹ and 270 mL g⁻¹ in river water and sea water, respectively. Results are interpreted in terms of the dissolution of ZnO and other residual complexes from the matrix and the subsequent, rapid adsorption of Zn²⁺ ions to coexistent estuarine sediment. The findings of the study are discussed in terms of their implications for the transport, fate and effects of TWP Zn in aquatic environments that are likely to receive urban runoff.     

Influence of Suwannee River humic acid on particle properties and toxicity of silver nanoparticles

Adsorption of natural organic matter (NOM) on nanoparticles can have dramatic impacts on particle dispersion resulting in altered fate and transport as well as bioavailability and toxicity. In this study, the adsorption of Suwannee River humic acid (SRHA) on silver nanoparticles (nano-Ag) was determined and showed a Langmuir adsorption at pH 7 with an adsorption maximum of 28.6 mg g⁻¹ nano-Ag. It was also revealed that addition of <10 mg L⁻¹ total organic carbon (TOC) increased the total Ag content suspended in the aquatic system, likely due to increased dispersion. Total silver content decreased with concentrations of NOM greater than 10 mg TOC L⁻¹ indicating an increase in nanoparticle agglomeration and settling above this concentration. However, SRHA did not have any significant effect on the equilibrium concentration of ionic Ag dissolved in solution. Exposure of Daphnia to nano-Ag particles (50 μg L⁻¹ and pH 7) produced a linear decrease in toxicity with increasing NOM. These results clearly indicate the importance of water chemistry on the fate and toxicity of nanoparticulates.     

Effects of the pharmaceuticals gemfibrozil and diclofenac on biomarker expression in the zebra mussel (Dreissena polymorpha) and their comparison with standardised toxicity tests

Pharmaceuticals, including the lipid regulator gemfibrozil and the non-steroidal anti-inflammatory drug diclofenac have been identified in waste water treatment plant effluents and receiving waters throughout the western world. The acute and chronic toxicity of these compounds was assessed for three freshwater species (Daphnia magna,Pseudokirchneriella subcapitata, Lemna minor) using standardised toxicity tests with toxicity found in the non-environmentally relevant mid mg L⁻¹ concentration range. For the acute endpoints (IC₅₀ and EC₅₀) gemfibrozil showed higher toxicity ranging from 29 to 59 mg L⁻¹ (diclofenac 47-67 mg L⁻¹), while diclofenac was more toxic for the chronic D. magna 21 d endpoints ranging from 10 to 56 mg L⁻¹ (gemfibrozil 32-100 mg L⁻¹). These results were compared with the expression of several biomarkers in the zebra mussel (Dreissena polymorpha) 24 and 96 h after exposure by injection to concentrations of 21 and 21,000 μg L⁻¹ corresponding to nominal concentrations of 1 and 1000 μg L⁻¹. Exposure to gemfibrozil and diclofenac at both concentrations significantly increased the level of lipid peroxidation, a biomarker of damage. At the elevated nominal concentration of 1000 μg L⁻¹ the biomarkers of defence glutathione transferase and metallothionein were significantly elevated for gemfibrozil and diclofenac respectively, as was DNA damage after 96 h exposure to gemfibrozil. No evidence of endocrine disruption was observed using the alkali-labile phosphate technique. Results from this suite of biomarkers indicate these compounds can cause significant stress at environmentally relevant concentrations acting primarily through oxidation pathways with significant destabilization of the lysosomal membrane and that biomarker expression is a more sensitive endpoint than standardised toxicity tests.     

Concentrations of cyclic volatile methylsiloxanes in biosolid amended soil,influent, effluent,receiving water,and sediment of wastewater treatment plants in Canada

A comprehensive surveillance program was conducted to determine the occurrence of three cyclic volatile methylsiloxanes (cVMS) octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and dodecamethylcyclohexasiloxane (D6) in environmental compartments impacted by wastewater effluent discharges. Eleven wastewater treatment plants (WWTPs), representative of those found in Southern Ontario and Southern Quebec, Canada, were investigated to determine levels of cVMS in their influents and effluents. In addition, receiving water and sediment impacted by WWTP effluents, and biosolid-amended soil from agricultural fields were also analyzed for a preliminary evaluation of the environmental exposure of cVMS in media impacted by wastewater effluent and solids. A newly-developed large volume injection (septumless head adapter and cooled injection system) gas chromatography – mass spectrometry method was used to avoid contamination originating from instrumental analysis. Concentrations of D4, D5, and D6 in influents to the 11 WWTPs were in the range 0.282–6.69 μg L⁻¹, 7.75–135 μg L⁻¹, and 1.53–26.9 μg L⁻¹, respectively. In general, wastewater treatment showed cVMS removal rates of greater than 92%, regardless of treatment type. The D4, D5, and D6 concentration ranges in effluent were <0.009–0.045 μg L⁻¹, <0.027–1.56 μg L⁻¹, and <0.022–0.093 μg L⁻¹, respectively. The concentrations in receiving water influenced by effluent, were lower compared to those in effluent in most cases, with the ranges <0.009–0.023 μg L⁻¹, <0.027–1.48 μg L⁻¹, and <0.022–0.151 μg L⁻¹ for D4, D5, and D6, respectively. Sediment concentrations ranged from <0.003–0.049 μg g⁻¹ dw, 0.011–5.84 μg g⁻¹ dw, and 0.004–0.371 μg g⁻¹ dw for D4, D5, and D6, respectively. The concentrations in biosolid-amended soil, having values of <0.008–0.017 μg g⁻¹ dw, <0.007–0.221 μg g⁻¹ dw, and <0.009–0.711 μg g⁻¹ dw for D4, D5, and D6, respectively, were lower than those in sediment impacted by wastewater effluent in most cases. In comparison with the no-observed-effected concentrations (NOEC) and IC50 (concentration that causes 50% inhibition of the response) values, the potential risks to aquatic, sediment-dwelling, and terrestrial organisms from these reported concentrations are low.     

Aerobic degradation of tetrabromobisphenol-A by microbes in river sediment

This study investigated the aerobic degradation of tetrabromobisphenol-A (TBBPA) and changes in the microbial community in river sediment from southern Taiwan. Aerobic degradation rate constants (k₁) and half-lives (t_1/2) for TBBPA (50 μg g⁻¹) ranged from 0.053 to 0.077 d⁻¹ and 9.0 to 13.1 d, respectively. The degradation of TBBPA (50 μg g⁻¹) was enhanced by adding yeast extract (5 mg L⁻¹), sodium chloride (10 ppt), cellulose (0.96 mg L⁻¹), humic acid (0.5 g L⁻¹), brij 30 (55 μM), brij 35 (91 μM), rhamnolipid (130 mg L⁻¹), or surfactin (43 mg L⁻¹), with rhamnolipid yielding a higher TBBPA degradation than the other additives. For different toxic chemicals in the sediment, the results showed the high-to-low order of degradation rates were bisphenol-A (BPA) (50 μg g⁻¹) > nonylphenol (NP) (50 μg g⁻¹) > 4,4′-dibrominated diphenyl ether (BDE-15) (50 μg g⁻¹) > TBBPA (50 μg g⁻¹) > 2,2′,3,3′,4,4′,5,5′,6,6′-decabromodiphenyl ether (BDE-209) (50 μg g⁻¹). The addition of various treatments changed the microbial community in river sediments. The results also showed that Bacillus pumilus and Rhodococcus ruber were the dominant bacteria in the process of TBBPA degradation in the river sediments.     

Occurrence of veterinary antibiotics in animal wastewater and surface water around farms in Jiangsu Province, China

The objective of this investigation was to obtain a broad profile of veterinary antibiotics residues in animal wastewater and surface water around large-scale livestock and poultry farms in Jiangsu Province of China. Therefore, 53 samples collected from 27 large-scale animal farms in 11 cities and counties of Jiangsu Province in 2009, were monitored for 10 selected veterinary antibiotics using solid phase extraction and high performance liquid chromatography/electrospray ionization-tandem mass spectrometry (HPLC/ESI-MS/MS) techniques. Ten veterinary antibiotics were found in animal wastewaters, eight antibiotics were detected in pond waters, and animal farm-effluents and river water samples were contaminated by nine antibiotics. The most frequently detected antibiotics were sulfamethazine (75%), oxytetracycline (64%), tetracycline (60%), sulfadiazine (55%) and sulfamethoxazole (51%) which were detected with a maximum concentration of 211, 72.9, 10.3, 17.0 and 63.6 μg L⁻¹, respectively. The maximum concentration of 0.55 μg L⁻¹ for cyromazine, 3.67 μg L⁻¹ for chlortetracycline, 0.63 μg L⁻¹ for sulfadoxine, 39.5 μg L⁻¹ for doxycycline and 0.64 μg L⁻¹ for sulfaquinoxaline were determined in the collected samples. In general, the maximum concentration of the selected veterinary antibiotics was detected in animal wastewaters except for chlortetracycline in animal farm-effluents. In addition, residue levels of selected veterinary antibiotics in animal wastewater and surface water around the farms were related to animal species and have a high spatial variation.     

Nano-TiO2 enhances the toxicity of copper in natural water to Daphnia magna

The acute toxicity of engineered nanoparticles (NPs) in aquatic environments at high concentrations has been well-established. This study demonstrates that, at a concentration generally considered to be safe in the environment, nano-TiO₂ remarkably enhanced the toxicity of copper to Daphnia magna by increasing the copper bioaccumulation. Specifically, at 2 mg L⁻¹ nano-TiO₂, the (LC₅₀) of Cu²⁺ concentration observed to kill half the population, decreased from 111 μg L⁻¹ to 42 μg L⁻¹. Correspondingly, the level of metallothionein decreased from 135 μg g⁻¹ wet weight to 99 μg g⁻¹ wet weight at a Cu²⁺ level of 100 μg L⁻¹. The copper was found to be adsorbed onto the nano-TiO₂, and ingested and accumulated in the animals, thereby causing toxic injury. The nano-TiO₂ may compete for free copper ions with sulfhydryl groups, causing the inhibition of the detoxification by metallothioneins.     

Preparation of controlled nano-MgO and investigation of its bactericidal properties

Nano-MgO is a good bactericide but with strong alkalinity in water due to its rapid hydrolysis. To control its hydrolysis rate and keep its bactericidal properties, we synthesized nano-MgO microspheres using chitosan-alginate system in this study. The synthesized nano-MgO release-controlled microspheres (nMgO-RCM) were with 0.98-1.20 mm of particle sizes. Also, their embedding ratio and loading percentage was 63.52% and 12.27%, respectively. Based on the characterization results, nano-MgO was only observed on surface of the nMgO-RCM. Its release rate from the nMgO-RCM could be controlled by the chitosan-alginate system, and the observed rate constant (k_obs) increased from 0.0289 h⁻¹ to 0.0358 h⁻¹ with the increment of the dosage from 10 mg L⁻¹ to 80 mg L⁻¹. Furthermore, the nMgO-RCM could maintain pH value lower than 8.5 and colony counts less than 20 CFU mL⁻¹ for at least 120 h.     

Monitoring and modelling of siloxanes in a sewage treatment plant in the UK

Monitoring of cyclic volatile methylsiloxanes (cVMS) carried out at Anglian Water’s Broadholme sewage treatment plant (STP) is described. The method deployed used headspace gas chromatography/mass spectrometry (HS-GC/MS) and the addition of isotopically labelled cVMS to correct for partitioning in samples containing high levels of particulate and dissolved organic carbon. The method was capable of measuring cVMS in raw sewage samples, with recoveries of 80%, 85% and 71% respectively, for D₄, D₅ and D₆. The limit of quantification was 0.2 μg L⁻¹ for all three substances. Recoveries close to 100% were observed for all cVMS spiked into treated effluent (LOQ = 0.01 μg L⁻¹). Despite the volatile nature of cVMS and its ubiquitous presence in the ambient atmosphere, the methods deployed showed excellent recoveries, reproducibility and quantification limits. A distinct diurnal variation in cVMS concentration, probably linked with the use of personal care products was observed for raw sewage but not in treated sewage effluent. The estimated per capita consumption of D₅ (∼2.7 mg cap⁻¹ d⁻¹) derived for the population served by this plant was significantly lower than that derived in the Environment Agency (UK) risk assessment (11.6 mg cap⁻¹ d⁻¹). The cVMS were highly removed during sewage treatment with efficiencies greater than 98%. The methods and findings of this pilot study can be used as the basis for future studies on the fate of cVMS substances in STPs.     

Removal potential of anti-estrogenic activity in secondary effluents by coagulation

Anti-estrogenic activity in wastewater is gaining increased attention because of its endocrine-disrupting function. In this study, the level and removal efficiency by coagulation of anti-estrogenic activity in secondary effluents of domestic wastewater treatment plants were studied. Anti-estrogenic activity was detected in secondary effluent samples at a tamoxifen (TAM) equivalent concentration level of 0.38–0.94 mg-TAM L⁻¹. Dissolved organic matters (DOM) with the molecular weight (MW) less than 3000 Da in hydrophobic acids (HOA) and hydrophobic neutrals (HON) fractions of the secondary effluent were the key fractions related to anti-estrogenic activity. Coagulation with FeCl₃ and polyaluminium chloride (PAC) can remove the anti-estrogenic activity of the secondary effluents, but the removal efficiency was limited. The removal efficiency using FeCl₃ coagulant was higher than that induced by PAC. Dissolved organic carbon was continuously removed with increased coagulant dose (0–120 mg L⁻¹ FeCl₃ or 0–60 mg L⁻¹ PAC). However, the removal of anti-estrogenic activity was not enhanced further when the coagulant concentration was beyond a critical value (30 mg L⁻¹ FeCl₃ or 10 mg L⁻¹ PAC). The highest removal of anti-estrogenic activity was about 36% by FeCl₃ and 20% by PAC. Size exclusion chromatography results indicated difficulty in removing DOM with MW less than 3000 Da in the secondary effluent during coagulation even at a high coagulant concentration, which led to low removal efficiency of anti-estrogenic activity.     

Simultaneous removal of arsenite and fluoride via an integrated electro-oxidation and electrocoagulation process

An integrated electro-oxidation and electrocoagulation system was designed and used to remove As(III) and F⁻ ions from water simultaneously. Dimensionally stable anodes (DSA), Fe electrodes, and Al electrodes were combined into an electrochemical system. Two pieces of DSA electrodes were assigned as the outside of the Fe and Al electrodes and were directly connected to the power supply as anode and cathode, respectively. The Fe and Al ions were generated by electro-induced process simultaneously. Subsequently, hydroxides of Fe and Al were formed. Arsenic ions are mainly removed by iron hydroxides and F⁻ ions are mainly removed by the Al oxides. At the initial concentration of 1.0 mg L⁻¹, most of As(III) was transferred into As(V) within 40 min at current density of 4 mA cm⁻², whereas F⁻ ions can be efficiently removed simultaneously. The effect of the ratio of Fe and Al plate electrodes and current density on the removal of As(III) and F⁻ was investigated. With one piece of Fe plate electrode and three pieces of Al plate electrodes, it is observed that As(III) with concentration of 1 mg L⁻¹ and F⁻ with concentration of 4.5 mg L⁻¹ can be removed and their final concentrations were below the values of 10 μg L⁻¹ and 1.0 mg L⁻¹, respectively within 40 min. Removal efficiency of As(III) increases with the increase of solution pH. However, in the pH range of 6-7, removal efficiency of F⁻ is the largest.     

Dental clinics: a point pollution source, not only of mercury but also of other amalgam constituents

Current literature suggests that amalgam waste from dental clinics is a point-source of mercury pollution in the environment. However, apart from mercury, other amalgam constituents (e.g. Ag, Sn, Cu, and Zn) in dental clinics’ wastewater have not been reported in the literature before. The objective of this study was to evaluate the concentrations of mercury and other metals in the wastewater of some dental clinics and the influent of a wastewater treatment plant in Al-Madinah Al-Munawarah (KSA). Samples were collected over a 2-month period from three dental clinics and analyzed for metals using ICP-MS. The mean concentrations of Hg, Ag, Sn, Cu, and Zn in the samples were 5.3 ± 11.1, 0.49 ± 0.96, 3.0 ± 10.7, 10.0 ± 14.5, and 76.7 ± 106 mg L⁻¹, respectively. Additionally, high concentrations of other metals such as Mg (14.4 ± 15.2 mg L⁻¹), Mn (3.0 ± 4.6 mg L⁻¹), Fe (3.0 ± 4.5 mg L⁻¹), Sr (1.6 ± 2.4 mg L⁻¹), and Ba (6.9 ± 10.3 mg L⁻¹) were also found. These values are much higher than the local permissible limits. Most of the metals of interest were also detected in the influent of the wastewater treatment plant. This renders dental clinics wastewater a hazardous waste which should be properly treated before it is discharged into the environment.     

Evaluation of recycling the effluent of hydrogen fermentation for biobutanol production: Kinetic study with butyrate and sucrose concentrations

Butyrate in the effluent of hydrogen-producing bioreactor is a potential feed for biobutanol production. For recycling butyrate, this study investigated the kinetics of biobutanol production by Clostridium beijerinckii NRRL B592 from different paired concentrations of butyrate and sucrose in a series of batch reactors. Results show that the lag time of butanol production increased with higher concentration of either sucrose or butyrate. In regression analyses, the maximum specific butanol production potential of 6.49 g g⁻¹ of dry cell was projected for 31.9 g L⁻¹ sucrose and 1.3 g L⁻¹ butyrate, and the maximum specific butanol production rate of 0.87 g d⁻¹ g⁻¹ of dry cell was predicted for 25.0 g L⁻¹ sucrose and 2.6 g L⁻¹ butyrate. The specific butanol production potential will decrease if more butyrate is added to the reactor. However, both sucrose and butyrate concentrations are weighted equally on the specific butanol production rate. This observation also is true on butanol yield. The maximum butanol yield of 0.49 mol mol⁻¹ was projected for 25.0 g L⁻¹ sucrose and 2.3 g L⁻¹ butyrate. In addition, a confirmation study found butanol yield increased from 0.2 to 0.3 mol mol⁻¹ when butyrate addition increased from 0 to 1 g L⁻¹ under low sugar concentration (3.8 g L⁻¹ sucrose). The existence of butyrate increases the activity of biobutanol production and reduces the fermentable sugar concentration needed for acetone–butanol–ethanol fermentation.     

Effects of four commonly used UV filters on the growth,cell viability and oxidative stress responses of the Tetrahymena thermophila

UV filters are increasingly used in sunscreens and other personal care products. Although their residues have been widely identified in aquatic environment, little is known about the influences of UV filters to protozoan. The growth inhibition effects, cell viability and oxidative stress responses of four commonly used UV filters, 2-ethylhexyl 4-methoxycinnamate (EHMC), benzophenone-3 (BP-3), 4-methyl-benzylidene camphor (4-MBC) and octocrylene (OC), to protozoan Tetrahymena thermophila were investigated in this study. The 24-h EC₅₀ values with 95% confidence intervals for BP-3 and 4-MBC were 7.544 (6.561–8.675) mg L⁻¹ and 5.125 (4.874–5.388) mg L⁻¹, respectively. EHMC and OC did not inhibit the growth of T. thermophila after 24 h exposure at the tested concentrations. The results of cell viability assays with propidium iodide (PI) staining were consistent with that of the growth inhibition tests. As for BP-3 and 4-MBC, the relatively higher concentrations, i.e. of 10.0 and 15.0 mg L⁻¹, could lead to the cell membranes impairment after 4 h exposure. With the increase of the exposure time to 6 h, their adverse effects on cell viability of T. thermophila were observed at the relatively lower concentration groups (1.0 mg L⁻¹ and 5.0 mg L⁻¹). In addition, it is noticeable that at environmentally relevant concentration (1.0 μg L⁻¹), BP-3 and 4-MBC could lead to the significant increase of catalase (CAT) activities of the T. thermophila cells. Especially for the BP-3, the oxidative injuries were further confirmed by the reduction of glutathione (GSH) content. It is imperative to further investigate the additive action of UV filters and seek other sensitive endpoint, especially at environmentally relevant concentration.     

Emerging pollutants in sewage, surface and drinking water in Galicia (NW Spain)

A monitoring programme was carried out on wastewater, surface and drinking water on the NW area of Spain during the four seasons of a year period (November 2007-September 2008). This study covered a series of emerging pollutants of different classes, including pharmaceuticals, neutral and acidic organophosphorus flame retardant/plasticizers (OPs), triclosan, phenoxy-herbicides, insect repellents and UV filters. From the total set of 53 compounds, 19 were found in raw wastewater with median concentrations higher than 0.1 μg L⁻¹. Among them, salicylic acid, ibuprofen and the UV filter benzophenone-4 (BP-4) were the most concentrated, exceeding the 1 μg L⁻¹ median value. Subsequently, 11 of these contaminants are not efficiently enough removed in the small WWTPs tested and their median concentrations in effluents still surpassed the 0.1 μg L⁻¹, so that they can spread through surface water. These chemicals are the pharmaceuticals naproxen, diclofenac and atenolol; the OPs tri(2-chloroethyl) phosphate (TCEP), tri(chloropropyl) phosphate (TCPP), tri-n-butyl phosphate (TnBP), diphenyl phosphate (DPhP) and diethylhexyl phosphate (DEHP); and the sulphonate UV filters BP-4 and 2-phenylbenzimidazole-5-sulphonic acid (PBSA). These OPs were then the dominant emerging pollutants occurring in surface and drinking water, where they are detected in the 20-200 ng L⁻¹ range. Pharmaceuticals and UV filters are typically below the 10 ng L⁻¹ level. Finally, herbicides were only detected in the last sampling campaign under the 100 ng L⁻¹ drinking water European Union limit.     

Biosafety assessment of titanium dioxide nanoparticles in acutely exposed nematode Caenorhabditis elegans with mutations of genes required for oxidative stress or stress response

We used Caenorhabditis elegans to investigate whether acute exposure to TiO₂-NPs at the concentration of 20 μg L⁻¹ reflecting predicted environmental relevant concentration and 25 mg L⁻¹ reflecting concentration in food can cause toxicity on nematodes with mutations of susceptible genes. Among examined mutants associated with oxidative stress and stress response, we found that genes of sod-2, sod-3, mtl-2, and hsp-16.48 might be susceptible for TiO₂-NPs toxicity. Mutations of these genes altered functions of both possible primary and secondary targeted organs in nematodes exposed to 25 mg L⁻¹ of TiO₂-NPs for 24-h. Mutations of these genes caused similar expression patterns of genes required for oxidative stress in TiO₂-NPs exposed mutant nematodes, implying their similar mechanisms to form the susceptible property. Nevertheless, acute exposure to 20 μg L⁻¹ of TiO₂-NPs for 24-h and 25 mg L⁻¹ of TiO₂-NPs for 0.48-h or 5.71-h did not influence functions of both possible primary and secondary targeted organs in sod-2, sod-3, mtl-2, and hsp-16.48 mutants. Therefore, our results suggest the relatively safe property of acute exposure to TiO₂-NPs with certain durations at predicted environmental relevant concentrations or concentrations comparable to those in food in nematodes with mutations of some susceptible genes.     

Zerovalent iron encapsulated chitosan nanospheres - a novel adsorbent for the removal of total inorganic arsenic from aqueous systems

Evaluation of Chitosan zerovalent Iron Nanoparticle (CIN) towards arsenic removal is presented. Addition of chitosan enhances the stability of Fe(0) nano particle. Prepared adsorbent was characterized by FT-IR, SEM EDX, BET and XRD. It was found that, with an initial dose rate of 0.5 g L⁻¹, concentrations of As (III) and As (V) were reduced from 2 mg L⁻¹ to <5 μg L⁻¹ in less than 180 min and the adsorbent was found to be applicable in wide range of pH. Langmuir monolayer adsorption capacity was found to be 94 ± 1.5 mg g⁻¹ and 119 ± 2.6 mg g⁻¹ at pH 7 for As (III) and As (V) respectively. Major anions including sulfate, phosphate and silicate did not cause significant interference in the adsorption behavior of both arsenite and arsenate. The adsorbent was successfully recycled five times and applied to the removal of total inorganic arsenic from real life groundwater samples.