Characterizing pesticide sorption and degradation in macro scale biopurification systems using column displacement experiments

The efficiency of biopurification systems to treat pesticide-contaminated water was previously studied in microcosms. To validate the obtained results, macrocosm systems were set-up. Four pesticides (linuron, isoproturon, bentazone, and metalaxyl) were continuously applied to ten different organic substrate mixes. Retention of the pesticides was similar and in some cases slightly lower in the macrocosms compared to the microcosms. Differences in retention between the different mixes were however minimal. Moreover, the classification of the retention strength of the pesticides was identical to that observed in microcosms: linuron > isoproturon > metalaxyl > bentazone. Monod kinetics were used to describe delayed degradation, which occurred for isoproturon, metalaxyl and bentazone. No breakthrough of linuron was observed, thus, this pesticide was appointed as the most retained and/or degraded pesticide, followed by isoproturon, metalaxyl and bentazone. Finally, most of the matrix mixes efficient in degrading or retaining pesticides were mixes containing dried cow manure.     

Transport and degradation of pesticides in a biopurification system under variable flux Part II: A macrocosm study

Transport of bentazone, isoproturon, linuron, metamitron and metalaxyl were studied under three different flows in macrocosms. The aim was to verify the observations from Part I of the accompanying paper, with an increase in column volume and decrease in chemical and hydraulic load. Very limited breakthrough occurred in the macrocosms for all pesticides, except bentazone, at all flows.From batch degradation experiments, it was observed that the lag time of metamitron and linuron decreased drastically in time for all flows, indicating a growth in the pesticide degrading population. This in contrast to isoproturon and metalaxyl, where an increase in lag time could be observed in time for all flows. From the batch degradation experiments, it could be concluded that the influence of flow on the lag time was minimal and that the inoculation of the pesticide-primed soil had a little surplus value on degradation.     

Enhanced retention of linuron, alachlor and metalaxyl in sandy soil columns intercalated with wood barriers

A study has been made of the effect a reactive barrier made of pine (softwood) or oak (hardwood) wood intercalated in a sandy soil column has on the retention of linuron, alachlor and metalaxyl (pesticides with contrasting physicochemical characteristics). The leaching of pesticides has been carried out under a saturated flow regime and breakthrough curves (BTCs) have been obtained at flow rates of 1 mL min⁻¹ (all pesticides) and 3 mL min⁻¹ (linuron). The cumulative curves in the unmodified soil indicate a leaching of pesticides >80% of the total amount of compound added. After barrier intercalation, linuron leaching decreases significantly and a modification of the leaching kinetics of alachlor and metalaxyl has been observed. The theoretical R factors increased ∼2.6-3.3, 1.2-1.6-fold, and 1.4-1.7-fold and the concentration of the maximum peak decreased ∼6-12-fold, 2-4-fold and 1.2-2-fold for linuron, alachlor and metalaxyl, respectively. When considering the three pesticides, significant correlations have been found between the theoretical retardation factor (R) and the pore volume corresponding to the maximum peaks of the BTCs (r = 0.77; p < 0.05) or the total volume leached (r = −0.78; p < 0.05). The results reveal the efficacy of reactive wood barriers to decrease the leaching of pesticides from point sources of pollution depends on the type of wood, the hydrophobicity of the pesticide and the adopted water flow rate. Pine was more effective than oak in decreasing the leaching of hydrophobic pesticide linuron or in decreasing the maximum peak concentration of the less hydrophobic pesticides in soils. Efficacy of these wood barriers was limited for the least hydrophobic pesticide metalaxyl.     

Transport and degradation of pesticides in a biopurification system under variable flux, part I: A microcosm study

The efficiency of a biopurification system, developed to treat pesticide contaminated water, is to a large extent determined by the chemical and hydraulic load. Insight into the behaviour of pesticides under different fluxes is necessary. The behaviour of metalaxyl, bentazone, linuron, isoproturon and metamitron was studied under three different fluxes with or without the presence of pesticide-primed soil in column experiments. Due to the time-dependent sorption process, retention of the pesticides with intermediate mobility was significantly influenced by the flux. The higher the flux, the slower pesticides will be sorbed, which resulted in a lower retention. Degradation of the intermediate mobile pesticides was also submissive to variations in flux. An increase in flux, led to a decrease in retention, which in turn decreased the opportunity time for biodegradation. Finally, the presence of pesticide-primed soil was only beneficial for the degradation of metalaxyl.     

Sorption kinetics and its effects on retention and leaching.

Sorption of pesticides to substrates used in biopurification systems is important as it controls the system's efficiency. Ideally, pesticide sorption should occur fast so that leaching of the pesticide in the biopurification system is minimized. Although modeling of pesticide transport commonly assumes equilibrium, this may not always be true in practice. Sorption kinetics have to be taken into account. This study investigated the batch sorption kinetics of linuron, isoproturon, metalaxyl, isoxaben and lenacil on substrates commonly used in a biopurification system, i.e. cow manure, straw, willow chopping, sandy loam soil, coconut chips, garden waste compost and peat mix. The first-order sorption kinetics model was fitted to the observed pesticide concentrations versus time resulting in an estimated kinetic rate constant alpha. Sorption appeared to be fast for the pesticides linuron and isoxaben, pesticides which were classified as immobile, while less mobile pesticides displayed an overall slower sorption. However, the substrate does not seem to be the main parameter influencing the sorption kinetics. Coconut chips, which is a substrate with a high organic matter content showed slow sorption for most of the pesticides. The effect of different estimated alpha values on the breakthrough of pesticides through a biopurification system was evaluated using the HYDRUS 1D model. Significant differences in leaching behavior were observed as a result of the obtained differences in sorption kinetics.     

Fate of seven pesticides in an aerobic aquifer studied in column experiments

The fate of selected pesticides (bentazone, isoproturon, DNOC, MCPP, dichlorprop and 2,4-D) and a metabolite (2,6-dichlorobenzamide (BAM)) was investigated under aerobic conditions in column experiments using aquifer material and low concentrations of pesticides (approximately 25 microg/l). A solute transport model accounting for kinetic sorption and degradation was used to estimate sorption and degradation parameters. Isoproturon and DNOC were significantly retarded by sorption, whereas the retardation of the phenoxy acids (MCPP, 2,4-D and dichlorprop), BAM and bentazone was very low. After lag periods of 16-33 days for the phenoxy acids and 80 days for DNOC, these pesticides were degraded quickly with 0.-order rate constants of 1.3-2.6 microg/l/day. None of the most probable degradation products were detected.     

Evaluating equilibrium and non-equilibrium transport of bromide and isoproturon in disturbed and undisturbed soil columns

In this study, displacement experiments of isoproturon were conducted in disturbed and undisturbed columns of a silty clay loam soil under similar rainfall intensities. Solute transport occurred under saturated conditions in the undisturbed soil and under unsaturated conditions in the sieved soil because of a greater bulk density of the compacted undisturbed soil compared to the sieved soil. The objective of this work was to determine transport characteristics of isoproturon relative to bromide tracer. Triplicate column experiments were performed with sieved (structure partially destroyed to simulate conventional tillage) and undisturbed (structure preserved) soils. Bromide experimental breakthrough curves were analyzed using convective-dispersive and dual-permeability (DP) models (HYDRUS-1D). Isoproturon breakthrough curves (BTCs) were analyzed using the DP model that considered either chemical equilibrium or non-equilibrium transport. The DP model described the bromide elution curves of the sieved soil columns well, whereas it overestimated the tailing of the bromide BTCs of the undisturbed soil columns. A higher degree of physical non-equilibrium was found in the undisturbed soil, where 56% of total water was contained in the slow-flow matrix, compared to 26% in the sieved soil. Isoproturon BTCs were best described in both sieved and undisturbed soil columns using the DP model combined with the chemical non-equilibrium. Higher degradation rates were obtained in the transport experiments than in batch studies, for both soils. This was likely caused by hysteresis in sorption of isoproturon. However, it cannot be ruled out that higher degradation rates were due, at least in part, to the adopted first-order model. Results showed that for similar rainfall intensity, physical and chemical non-equilibrium were greater in the saturated undisturbed soil than in the unsaturated sieved soil. Results also suggested faster transport of isoproturon in the undisturbed soil due to higher preferential flow and lower fraction of equilibrium sorption sites.     

A comparison of five pesticides adsorption and desorption processes in thirteen contrasting field soils

Batch adsorption and desorption experiments were performed using thirteen agricultural soil samples and five pesticides. Experimental data indicated a gradient in pesticide adsorption on soil: trifluralin > 2,4-D > isoproturon> atrazine > bentazone. Atrazine, isoproturon and trifluralin adsorption were correlated to soil organic matter content (r2 = 0.7, 0.82, 0.79 respectively). Conversely, bentazone adsorption was governed by soil pH (r2 = 0.68) while insignificant effect has been shown in the case of 2,4-D. Multiple linear regressions were used to combine relationships between the various soil parameters and the Freundlich adsorption coefficient (K(f)) of each pesticide. Then desorption was assessed since it may reflect some of the interactions involved between the pesticides and the soil components. Adsorbed molecules were released into aqueous solution in the following order: bentazone > atrazine> isoproturon> 2,4-D > trifluralin. The occurrence of hysteresis did not allow an accurate interpretation of the pesticide desorption data because of the possible interplay of several processes.     

Modelling the dissipation kinetics of six commonly used pesticides in two contrasting soils of New Zealand

We used three non-linear bi-phasic models, bi-exponential (BEXP), first-order double exponential decay (FODED), and first-order two-compartment (FOTC), to fit the measured degradation data for six commonly used pesticides (atrazine, terbuthylazine, bromacil, diazinon, hexazinone and procymidone) in two New Zealand soils. Corresponding DT₅₀ and DT₉₀ values for each compound were numerically obtained and compared against those estimated by simple first-order kinetic (SFOK) model. All 3 non-linear models gave good fit of the measured data under both soil depths and were well supported by the values obtained for the respective statistical indices (RMSE, CRM and r ²). The FOTC model gave by far the best fit for most compounds, followed by the FODED and BEXP models. Overall, DT₅₀ values derived by non-linear models for the six compounds in soils from both sites were lower than the values obtained by the SFOK model. Differences in the SFOK and the three non-linear models derived DT₉₀were, however, an order of magnitude higher for some compounds, while for others differences were very small. Although all three non-linear models described most data by giving excellent fits, in a few instances > 5–10% asymptotes hindered the estimation of DT₉₀ values. This work shows that when degradation deviates from first-order kinetic, application of non-linear decay models to describe the kinetics of degradation becomes important in order to derive the true end-points for pesticides in soil.     

Photolytic degradation of decabromodiphenyl ethane (DBDPE)

The photolytic degradation of decabromodiphenyl ethane (DBDPE), an alternative flame retardant to decabromodiphenyl ether, was investigated in a variety of matrixes (n-hexane, tetrahydrofuran, methanol/water, humic acid/water, and silica gel) by irradiation under ultraviolet light and in n-hexane under natural light. Photolytic degradation of DBDPE occurs in all the matrixes investigated within the irradiation period (<320 min). The degradation experiments showed varied reaction rates, dependent on the matrixes, with increasing half-lives (t_1/2) in the order of tetrahydrofuran (t_1/2 = 6.0 min) > n-hexane (t_1/2 = 16.6 min) > humic acid/water (30 < t_1/2 < 60) > silica gel (t_1/2 = 75.9 min) > methanol/water (t_1/2 > 240 min). The reaction in tetrahydrofuran, n-hexane, and silica gel matrixes can be described by the pseudo first order kinetics. Nevertheless, the matrixes have little effect on the degradation product distributions of DBDPE. A numbers of debrominated intermediates were identified. The degradation involves the initial formation of nona-BDPEs and the subsequent decomposition of these congeners to lower brominated congeners (octa- and hepta-BDPEs) within the irradiation time. To our knowledge, the present work is the first attempt to investigate the photolytic degradation kinetics and the identification of intermediates, as well as the degradation mechanism, during the degradation of DBDPE. Further research is needed to understand the photolytic degradation pattern of DBDPE in the natural environment.     

Analyses of locally measured bromide breakthrough curves from a natural gradient tracer experiment at Krauthausen

Solute travel time distributions were derived from breakthrough curves (BTCs) of bromide concentrations, which were measured during a large-scale tracer experiment in a quaternary fluviatile aquifer at Krauthausen. Travel time distributions to a specific point in the aquifer were derived from locally measured BTCs, using averaged absolute concentrations ?abs(x1,t), normalized concentrations ?norm(x1,t), and velocity-weighted normalized concentrations ?vw(x1,t). The travel time distributions were characterized in terms of equivalent convective-dispersive transport parameters: the equivalent solute velocity and equivalent dispersivity. Parameters were derived from BTCs using moment analyses and least-squares fits of the 1-D convection-dispersion equation (CDE). Both local and averaged BTCs showed pronounced tailing which was not well described by the 1-D CDE and which indicates the presence of macroscopic regions with low velocities in the aquifer. Therefore, dispersivities derived from CDE fits were significantly smaller than those derived from time moments. The BTCs of ?abs(x1,t) were dominated by only a few local BTCs with high concentrations and were less representative for the travel time distribution than BTCs of averaged normalized concentrations. Dispersivities derived from ?norm(x1,t) and ?vw(x1,t) were very similar. Finally, estimates of dispersivities and vertical correlation length of lnK, gamma 3, from BTCs were in agreement with a first-order estimate of the dispersivity and gamma 3 based on grain size data and flow meter measurements.     

Minimal pesticide-primed soil inoculum density to secure maximum pesticide degradation efficiency in on-farm biopurification systems

Addition of pesticide-primed soil containing adapted pesticide degrading bacteria to the biofilter matrix of on farm biopurification systems (BPS) which treat pesticide contaminated wastewater, has been recommended, in order to ensure rapid establishment of a pesticide degrading microbial community in BPS. However, uncertainties exist about the minimal soil inoculum density needed for successful bioaugmentation of BPS. Therefore, in this study, BPS microcosm experiments were initiated with different linuron primed soil inoculum densities ranging from 0.5 to 50 vol.% and the evolution of the linuron mineralization capacity in the microcosms was monitored during feeding with linuron. Successful establishment of a linuron mineralization community in the BPS microcosms was achieved with all inoculum densities including the 0.5 vol.% density with only minor differences in the time needed to acquire maximum degradation capacity. Moreover, once established, the robustness of the linuron degrading microbial community towards expected stress situations proved to be independent of the initial inoculum density. This study shows that pesticide-primed soil inoculum densities as low as 0.5 vol.% can be used for bioaugmentation of a BPS matrix and further supports the use of BPS for treatment of pesticide-contaminated wastewater at farmyards.     

Evaluating non-equilibrium solute transport in small soil columns

Displacement studies on leaching of bromide and two pesticides (atrazine and isoproturon) were conducted under unsaturated steady state flow conditions in 24 small undisturbed soil columns (5.7 cm in diameter and 10 cm long) each collected from two sites differing in soil structure and organic carbon content in North Germany. There were large and irregular variabilities in the characteristics of both soils, as well as in the shapes of breakthrough curves (BTCs) of different columns, including some with early breakthrough and increased tailing, qualitatively indicating the presence of preferential flow. It was estimated that one preferential flow column (PFC) at site A, and four at site B, contributed, respectively to 11% and 58% of the accumulated leached fraction and to more than 80% of the maximum observed standard deviation (SD) in the field-scale concentration and mass flux of pesticides at two sites. The bromide BTCs of two sites were analyzed with the equilibrium convection-dispersion equation (CDE) and a non-equilibrium two-region/mobile-immobile model. Transport parameters of these models for individual BTCs were determined using a curve fitting program, CXTFIT, and by the time moment method. For the CDE based equilibrium model, the mean values of retardation factor, R, considered separately for all columns, PFCs or non-preferential flow columns (NPFCs) were comparable for the two methods; significant differences were observed in the values of dispersion coefficients of two sites using the two estimation methods. It was inferred from the estimated parameters of non-equilibrium model that 5-12% of water at site A, and 12% at site B, was immobile during displacement in NPFCs. The corresponding values for PFCs of two sites were much larger, ranging from 25% to 51% by CXTFIT and from 24% to 72% by the moment method, suggesting the role of certain mechanisms other than immobile water in higher degrees of non-equilibrium in these columns. Peclet numbers in PFCs of both sites were consistently smaller than five, indicating the inadequacy of the non-equilibrium model to incorporate the effect of all forms of non-equilibrium in PFCs. Overall, the BTCs of individual NPFCs, PFCs and of field average concentration at the two sites were better reproduced with parameters obtained from CXTFIT than by the moment method. The moment method failed to capture the peak concentrations in PFCs, but tended to describe the desorption and tail branches of BTCs better than the curve fitting approach.     

Estimating the spatial scale of herbicide and soil interactions by nested sampling, hierarchical analysis of variance and residual maximum likelihood

An unbalanced nested sampling design was used to investigate the spatial scale of soil and herbicide interactions at the field scale. A hierarchical analysis of variance based on residual maximum likelihood (REML) was used to analyse the data and provide a first estimate of the variogram. Soil samples were taken at 108 locations at a range of separating distances in a 9 ha field to explore small and medium scale spatial variation. Soil organic matter content, pH, particle size distribution, microbial biomass and the degradation and sorption of the herbicide, isoproturon, were determined for each soil sample. A large proportion of the spatial variation in isoproturon degradation and sorption occurred at sampling intervals less than 60 m, however, the sampling design did not resolve the variation present at scales greater than this. A sampling interval of 20-25 m should ensure that the main spatial structures are identified for isoproturon degradation rate and sorption without too great a loss of information in this field.     

Metabolites of the phenylurea herbicides chlorotoluron, diuron, isoproturon and linuron produced by the soil fungus Mortierella sp.

Phenylurea herbicides are used worldwide, and often pollute surface- and groundwater in concentrations exceeding the limit value for drinking water (0.1 μg l⁻¹). Bacteria degrade phenylurea herbicides by successive N-dealkylation to substituted aniline products. Little is known about the corresponding fungal pathways, however. We here report degradation of chlorotoluron, diuron, isoproturon and linuron by the soil fungus Mortierella sp. Gr4. Degradation was fastest with linuron and resulted in successively dealkylated metabolites and 3,4-dichloroaniline. A major new metabolite was detected that has not yet been fully identified. Thin layer chromatography and nuclear magnetic resonance spectroscopy indicate that it is a non-aromatic diol. Degradation of isoproturon, chlorotoluron and diuron involved successive N-demethylation and, in the case of isoproturon and chlorotoluron, additional hydroxylation. A new hydroxylated isoproturon metabolite was detected. The study thus shows that the fungal pathways differ from the bacterial pathways and yield new metabolites of possible environmental concern.     

Electrochemical oxidation of nitrogen-heterocyclic compounds at boron-doped diamond electrode

Nitrogen-heterocyclic compounds (NHCs) are toxic and bio-refractory contaminants widely spread in environment. This study investigated electrochemical degradation of NHCs at boron-doped diamond (BDD) anode with particular attention to the effect of different number and position of nitrogen atoms in molecular structure. Five classical NHCs with similar structures including indole (ID), quinoline (QL), isoquinoline (IQL), benzotriazole (BT) and benzimidazole (BM) were selected as the target compounds. Results of bulk electrolysis showed that degradation of all NHCs was fit to a pseudo first-order equation. The five compounds were degraded with the following sequence: ID > QL > IQL > BT > BM in terms of their rates of oxidation. Quantum chemical calculation was combined with experimental results to describe the degradation character of NHCs at BDD anode. A linear relationship between degradation rate and delocalization energy was observed, which demonstrated that electronic charge was redistributed through the conjugation system and accumulated at the active sites under the attack of hydroxyl radicals produced at BDD anode. Moreover, atom charge was calculated by semi empirical PM3 method and active sites of NHCs were identified respectively. Analysis of intermediates by GC-MS showed agreement with calculation results.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

Elimination of racemic and enantioenriched metalaxyl based fungicides under tropical conditions in the field

The elimination has been studied of racemic and enantioenriched metalaxyl applied as an emulsifiable concentrate and wettable powder combined with copper in a Cameroonian field site. The kinetics of the degradation/dissipation of metalaxyl and its acid metabolite were investigated using reversed phase HPLC-MS/MS, while the enantiomeric ratios were measured by HPLC-MS/MS using a Chiralcel OD-H HPLC column. Some soil enzymes activities were determined concurrently for 120d. The elimination of racemic metalaxyl was shown to be enantioselective, with the R-enantiomer being degraded more slowly than the S-enantiomer. Dissipation followed approximate square root first-order kinetics (R>0.98) without lag phases. The enantiomers of metalaxyl have different elimination rates, with half-lives ranging from only 0.8 to 1.5 days. After application to soil, the elimination of metalaxyl in the copper containing formulation was slower. The activities of acid phosphatase, alkaline phosphatase, and alkaline glucosidase were monitored throughout the experiments. No significant influence of metalaxyl and copper could be observed on these parameters. The significantly shorter half-life values of all forms of metalaxyl under field conditions, compared to the previously reported laboratory derived ones, may have implications for the plant disease control with these fungicides in tropical rainforest areas.     

Lindane removal by pure and mixed cultures of immobilized actinobacteria

Stereoselective dissipation of epoxiconazole had been studied in grape and soil during plant growing under field conditions in this paper. A sensitive and rapid chiral method was developed and validated for the determination of epoxiconazole stereoisomers in grape and soil based on liquid chromatography coupled with triple quadrupole mass spectrometry (LC-MS/MS). Phenomenex Lux Cellulose-1 column was used for enantioseparation with a mixture of acetonitrile/water (90/10, v/v) as mobile phase at flow rate of 0.3 mL min⁻¹. Fortified recoveries in grape and soil samples ranged from 76.0% to 91.9% and relative standard deviations were less than 11.4% with fortified levels of 0.025-1.0 mg kg⁻¹. The limits of detection and quantification were 0.005 mg kg⁻¹ and 0.025 mg kg⁻¹, respectively, with linear calibration curves extending up to 5.0 mg kg⁻¹. The field experimental results showed that dissipations of epoxiconazole stereoisomers in grape followed first-order kinetics (R² > 0.92) and stereoselectivity occurred in 2 h after spraying. The (−)-stereoisomer with half-life of 9.3 d degraded faster than (+)-stereoisomer with that of 13.2 d, and resulted in relative enrichment of (+)-stereoisomer. However, the stereoisomeric dissipations in soil were triphasic (“increase-decrease-steady”) with lower dissipation rates, and also occurred with preferential degradation of (−)-stereoisomer under field condition. The results for stereoselective dissipations can be applied for food and environmental assessments of chiral pesticides.