Leaching of copper and zinc from spent antifouling paint particles

Leaching of Cu and Zn from a composite of spent antifouling paint particles, containing about 300 mg g⁻¹ and 110 mg g⁻¹ of the respective metals, was studied in batch experiments. For a given set of simulated environmental conditions, release of Cu was independent of paint particle concentration due to attainment of pseudo-saturation, but Zn was less constrained by solubility effects and release increased with increasing particle concentration. Leaching of Cu increased but Zn decreased with increasing salinity, consistent with mechanisms governing the dissolution of Cu₂O in the presence of chloride and Zn acrylates in the presence of seawater cations. Because of complex reaction kinetics and the presence of calcium carbonate in the paint matrix, metal leaching appeared to be greater at 4 °C than 19 °C under many conditions. These findings have important environmental and biological implications regarding the deliberate or inadvertent disposal of antifouling paint residues.     

Seabird feathers as monitors of the levels and persistence of heavy metal pollution after the Prestige oil spill

We measured heavy metal concentrations in yellow-legged gulls (n = 196) and European shags (n = 189) in order to assess the temporal pattern of contaminant exposure following the Prestige oil spill in November 2002. We analysed Pb, Cu, Zn, Cr, Ni and V levels in chick feathers sampled at four colonies during seven post-spill years (2003-2009), and compared results with pre-spill levels obtained from feathers of juvenile shag corpses (grown in spring/summer 2002). Following the Prestige wreck, Cu (4.3-10 μg g⁻¹) and Pb concentrations (1.0-1.4 μg g⁻¹) were, respectively, between two and five times higher than pre-spill levels (1.5-3.6 and 0.1-0.4 μg g⁻¹), but returned to previous background concentrations after three years. Our study highlights the suitability of chick feathers of seabirds for assessing the impact of oil spills on heavy metal contamination, and provides the best evidence to date on the persistence of oil pollution after the Prestige incident.     

Effects of biochar and the earthworm Eisenia fetida on the bioavailability of polycyclic aromatic hydrocarbons and potentially toxic elements

Polycyclic aromatic hydrocarbons (PAHs) and potentially toxic elements (PTEs) were monitored over 56 days in calcareous contaminated-soil amended with either or both biochar and Eisenia fetida. Biochar reduced total (449 to 306 mg kg⁻¹) and bioavailable (cyclodextrin extractable) (276 to 182 mg kg⁻¹) PAHs, PAH concentrations in E. fetida (up to 45%) but also earthworm weight. Earthworms increased PAH bioavailability by >40%. Combined treatment results were similar to the biochar-only treatment. Earthworms increased water soluble Co (3.4 to 29.2 mg kg⁻¹), Cu (60.0 to 120.1 mg kg⁻¹) and Ni (31.7 to 83.0 mg kg⁻¹) but not As, Cd, Pb or Zn; biochar reduced water soluble Cu (60 to 37 mg kg⁻¹). Combined treatment results were similar to the biochar-only treatment but gave a greater reduction in As and Cd mobility. Biochar has contaminated land remediation potential, but its long-term impact on contaminants and soil biota needs to be assessed.     

Conditioning of sewage sludge by Fenton's reagent combined with skeleton builders

Physical conditioners, often known as skeleton builders, are commonly used to improve the dewaterability of sewage sludge. This study evaluated a novel joint usage of Fenton’s reagent and skeleton builders, referred to as the F-S inorganic composite conditioner, focusing on their efficacies and the optimization of the major operational parameters. The results demonstrate that the F-S composite conditioner for conditioning sewage sludge is a viable alternative to conventional organic polymers, especially when ordinary Portland cement (OPC) and lime are used as the skeleton builders. Experimental investigations confirmed that Fenton reaction required sufficient time (80 min in this study) to degrade organics in the sludge. The optimal condition of this process was at pH = 5, Fe²⁺ = 40 mg g⁻¹ (dry solids), H₂O₂ = 32 mg g⁻¹, OPC = 300 mg g⁻¹ and lime = 400 mg g⁻¹, in which the specific resistance to filtration reduction efficiency of 95% was achieved.     

Hyperaccumulation of zinc by Corydalis davidii in Zn-polluted soils

A field survey was conducted to identify potential Zn accumulators from an artisanal Zn smelting area in southwest China’s Guizhou Province. Hydroponic and soil culture experiments were performed to investigate the accumulation ability of Zn in Corydalis davidii. Zn concentrations in roots, stems and leaves of C. davidii in the smelting site were 1.1-3.5, 1.2-11.2, and 3.3-14 mg g⁻¹, respectively, whereas Zn concentrations in roots, stems and leaves of C. davidii in the contaminated site impacted by the Zn smelting were 1.0-2.4, 1.9-6.5, and 3.0-1.1 mg g⁻¹, respectively. Zn concentrations in leaves and stems of C. davidii were observed at above 10 mg g⁻¹ that refers to the threshold of Zn hyperaccumulator. The concentration distribution of Zn in C. davidii was leaf > stem > root, and the Zn bioaccumulation factors of C. davidii were above 1. It is concluded that C. davidii has high tolerance to concentrate Zn stress, and that C. davidii is a newly discovered Zn-hyperaccumulator with high biomass in the aboveground parts. Based on the cultivation experiments, C. davidii could reduce Zn concentration by 26.6, 21.2, and 10.2 mg kg⁻¹yr⁻¹ by phytoextraction from the smelting slag, Zn-contaminated soil, and background soil, respectively.     

Correlation of foliar MT2b expression with Cd and Zn concentrations in hybrid aspen (Populus tremula × tremuloides) grown in contaminated soil

Metal uptake and its effect on foliar metallothionein 2b (MT2b) mRNA levels were studied in hybrid aspen (Populus tremula × tremuloides) in field conditions. The trees were planted on a site contaminated with several metals, including cadmium (mean 5.1 mg kg⁻¹), chromium (80 mg kg⁻¹), copper (180 mg kg⁻¹), nickel (81 mg kg⁻¹), vanadium (240 mg kg⁻¹) and zinc (520 mg kg⁻¹). Of the ten trace elements analyzed, only Cd and Zn accumulated in the leaves with maximal foliar concentrations of 35 and 2400 mg kg⁻¹ (dry weight), respectively. There was a strong correlation between Cd and Zn concentrations and bioaccumulation factors (concentration in plant/soil) in the leaves, branches and roots, suggesting similar transport mechanisms for these two metals. The levels of MT2b correlated with Cd and Zn concentrations in the leaves, demonstrating that increased MT2b expression is one of the responses of hybrid aspen to chronic metal exposure.     

Cadmium accumulation in and tolerance of rice (Oryza sativa L.) varieties with different rates of radial oxygen loss

Cadmium (Cd) uptake and tolerance were investigated among 20 rice cultivars based on a field experiment (1.2 mg Cd kg⁻¹ in soil) and a soil pot trial (control, 100 mg Cd kg⁻¹), and rates of radial oxygen loss (ROL) were measured under a deoxygenated solution. Significant differences were found among the cultivars in: (1) brown rice Cd concentrations (0.11-0.29 mg kg⁻¹) in a field soil, (2) grain Cd tolerance (34-113%) and concentrations (2.1-6.5 mg kg⁻¹) in a pot trial, and (3) rates of ROL (15-31 mmol O₂ kg⁻¹ root d.w. h⁻¹). Target hazard quotients were calculated for the field experiment to assess potential Cd risk. Significant negative relationships were found between rates of ROL and concentrations of Cd in brown rice or straw under field and greenhouse conditions, indicating that rice cultivars with higher rates of ROL had higher capacities for limiting the transfer of Cd to rice and straw.     

Concentrations and assessment of exposure to siloxanes and synthetic musks in personal care products from China

We investigated the concentrations and profiles of 15 siloxanes (four cyclic siloxanes, D₄-D₇; 11 linear siloxanes, L₄-L₁₄), four synthetic musks (two polycyclic musks, HHCB and AHTN; two nitro musks, MX and MK), and HHCB-lactone, in 158 personal care products marketed in China. Siloxanes were detected in 88% of the samples analyzed, at concentrations as high as 52.6 mg g⁻¹; Linear siloxanes were the predominant compounds. Among synthetic musks, more than 80% of the samples contained at least one of these compounds, and their total concentrations were as high as 1.02 mg g⁻¹. HHCB was the predominant musk in all of the samples analyzed, on average, accounting for 52% of the total musk concentrations. Based on the median concentrations of siloxanes and musks and the average daily usage amounts of consumer products, dermal exposure rates in adults were calculated to be 3.69 and 3.38 mg d⁻¹ for siloxanes and musks, respectively.     

Estimation of daily intake of potentially toxic elements from urban street dust and the role of oral bioaccessibility testing

The pseudo-total and oral bioaccessible concentration of six potentially toxic elements (PTEs) in urban street dust was investigated. Typical pseudo-total concentrations across the sampling sites ranged from 4.4 to 8.6 mg kg⁻¹ for As, 0.2-3.6 mg kg⁻¹ for Cd, 25-217 mg kg⁻¹ for Cu, 14-46 mg kg⁻¹ for Ni, 70-4261 mg kg⁻¹ for Pb, and, 111-652 mg kg⁻¹ for Zn. This data compared favourably with other urban street dust samples collected and analysed in a variety of cities globally; the exception was the high level of Pb determined in a specific sample in this study. The oral bioaccessibility of PTEs in street dust is also assessed using in vitro gastrointestinal extraction (Unified Bioaccessibility Method, UBM). Based on a worst case scenario the oral bioaccessibility data estimated that Cd and Zn had the highest % bioaccessible fractions (median >45%) while the other PTEs i.e. As, Cu, Ni and Pb had lower % bioaccessible fractions (median <35%). The pseudo-total and bioaccessible concentrations of PTEs in the samples has been compared to estimated tolerable daily intake values based on unintentional soil/dust consumption. Cadmium, Cu and Ni are well within the oral tolerable daily intake rates. With respect to As and Pb, only the latter exceeds the TDI_oral if we model ingestion rate based on atmospheric ‘dustiness’ rather than the US EPA (2008) unintentional soil/dust consumption rate of 100 mg d⁻¹. We consider it unlikely that even a child with pica tendencies would ingest as much as 100 mg soil/dust during a daily visit to the city centre, and in particular to the sites with elevated Pb concentrations observed in this study.     

Leaching of zinc from tire wear particles under simulated estuarine conditions

Tire wear particles (TWP) abraded from end-of-life passenger car tires have been added at a concentration of 1 g L⁻¹ to river water, sea water and mixtures thereof in order to examine the chemical controls on the leaching of Zn from the rubber matrix. Results of time-dependent experiments conducted over a period of 5 days were consistent with a diffusion controlled leaching mechanism with rate constants of about 0.04 mg L⁻¹ h^−1/2 in river water and between about 0.02 and 0.03 mg L⁻¹ h^−1/2 in sea water. Additional experiments revealed a reduction in Zn dissolution with both increasing salinity and pH and enhancement of leaching in the presence of fluorescent light compared with dark conditions. In corresponding experiments conducted in the presence of a fixed quantity (0.8 g L⁻¹) of clean, fractionated estuarine sediment, aqueous Zn concentrations were reduced by at least an order of magnitude. Increasing the quantity of sediment resulted in a progressive reduction in Zn concentration until an apparent equilibrium was achieved, with partition coefficients defining the sediment-water distribution of Zn of about 550 mL g⁻¹ and 270 mL g⁻¹ in river water and sea water, respectively. Results are interpreted in terms of the dissolution of ZnO and other residual complexes from the matrix and the subsequent, rapid adsorption of Zn²⁺ ions to coexistent estuarine sediment. The findings of the study are discussed in terms of their implications for the transport, fate and effects of TWP Zn in aquatic environments that are likely to receive urban runoff.     

Mercury in United Kingdom topsoils; concentrations, pools, and Critical Limit exceedances

The median total mercury concentration in 898 UK rural topsoils, sampled between 1998 and 2008, was 0.095 μg g⁻¹. Approximate adjustment for unreactive metal produced an estimate of 0.052 μg g⁻¹ for reactive Hg. The highest concentrations were in the north and west, where organic-rich soils with low bulk densities dominate, but the spatial pattern was quite different if soil Hg pools (mg m⁻²) were considered, the highest values being near to the industrial north of England and London. Possible toxic effects of Hg were best evaluated by comparison with soil Critical Limits expressed as ratios of Hg to soil organic matter, or soil solution Hg²⁺ concentrations, estimated by chemical speciation modelling. Only a few percent of the rural UK soils showed exceedance, and this also applied to rural soils from the whole of Europe. UK urban and industrial soils had higher Hg concentrations and more cases of exceedance.     

Occurrence and behaviour of selected hydrophobic alkylphenolic compounds in the Danube River

Six hydrophobic alkylphenolic compounds were investigated for the first time simultaneously in four different matrices in the Danube River. Maximum sediment concentrations were 2.83, 2.10, 0.28, and 0.035 mg kg⁻¹ for nonylphenol, nonylphenol monoethoxylate, nonylphenol diethoxylate and octylphenol. Maximum levels in suspended particulate matter (SPM) were 0.18, 0.12, 0.10, and 0.003 mg kg⁻¹. No correlation between concentrations in SPM and sediments was found. Octylphenol monoethoxylate and octylphenol diethoxylate were recorded only in sediment at one location. In mussels and water only nonylphenol and octylphenol were found. Nonylphenol concentrations in mussels (up to 0.34 mg kg⁻¹) correlate with concentrations found in SPM and indicate a slight bioaccumulation. Concentrations in water were close to the limit of quantification. We assume in situ formation of nonylphenol monoethoxylate and nonylphenol in sediments at some locations. In some cases nonylphenol in sediments exceeded the provisional EU environmental quality standards.     

Impact of earthworms on trace element solubility in contaminated mine soils amended with green waste compost

The common practice of remediating metal contaminated mine soils with compost can reduce metal mobility and promote revegetation, but the effect of introduced or colonising earthworms on metal solubility is largely unknown. We amended soils from an As/Cu (1150 mgAs kg⁻¹ and 362 mgCu kg⁻¹) and Pb/Zn mine (4550 mgPb kg⁻¹ and 908 mgZn kg⁻¹) with 0, 5, 10, 15 and 20% compost and then introduced Lumbricus terrestris. Porewater was sampled and soil extracted with water to determine trace element solubility, pH and soluble organic carbon. Compost reduced Cu, Pb and Zn, but increased As solubility. Earthworms decreased water soluble Cu and As but increased Pb and Zn in porewater. The effect of the earthworms decreased with increasing compost amendment. The impact of the compost and the earthworms on metal solubility is explained by their effect on pH and soluble organic carbon and the environmental chemistry of each element.     

Hormetic effect(s) of tetracyclines as environmental contaminant on Zea mays

Animal wastes from intensive pig farming as fertilizers may expose crops to antimicrobials. Zea mays cultivations were carried out on a virgin field, subjected to dressing with pig slurries contaminated at 15 mg L⁻¹ of Oxy- and 5 mg L⁻¹ of Chlor-tetracycline, and at 8 mg L⁻¹ of Oxy and 3 mg L⁻¹ of Chlor, respectively. Pot cultivation was performed outdoor (Oxy in the range 62.5-1000 ng g⁻¹ dry soil) and plants harvested after 45 days. Tetracyclines analyses on soils and on field plants (roots, stalks, and leaves) did not determine the appreciable presence of tetracyclines. Residues were found in the 45-day pot corn only, in the range of 1-50 ng g⁻¹ for Oxy in roots, accounting for a 5% carry-over rate, on average. Although no detectable residues in plants from on land cultivations, both experimental batches showed the same biphasic growth form corresponding to a dose/response hormetic curve.     

Zinc accumulation and synthesis of ZnO nanoparticles using Physalis alkekengi L

A field survey and greenhouse experiments were conducted using Physalis alkekengi L. to investigate strategies of phytoremediation. In addition, ZnO nanoparticles were synthesized using P. alkekengi. P. alkekengi plants grew healthily at Zn levels from 50 to 5000 mg kg⁻¹ in soils. The plants incorporated Zn into their aerial parts (with mean dry weight values of 235-10,980 mg kg⁻¹) and accumulated biomass (with a mean dry weight of 25.7 g plant⁻¹) during 12 weeks. The synthesized ZnO nanoparticles showed a polydisperse behavior and had a mean size of 72.5 nm. The results indicate that P. alkekengi could be used for the remediation of zinc-contaminated soils. Moreover, the synthetic method of synthesizing ZnO nanoparticles from Zn hyperaccumulator plants constitutes a new insight into the recycling of metals in plant sources.     

Triclosan affects the microbial community in simulated sewage-drain-field soil and slows down xenobiotic degradation

Effects of the common antibacterial agent triclosan on microbial communities and degradation of domestic xenobiotics were studied in simulated sewage-drain-field soil. Cultivable microbial populations decreased 22-fold in the presence of 4 mg kg⁻¹ of triclosan, and triclosan-resistant Pseudomonas strains were strongly enriched. Exposure to triclosan also changed the general metabolic profile (Ecoplate substrate profiling) and the general profile (T-RFLP) of the microbial community. Triclosan degradation was slow at all concentrations tested (0.33-81 mg kg⁻¹) during 50-days of incubation. Mineralization experiments (¹⁴C-tracers) and chemical analyses (LC-MS/MS) showed that the persistence of a linear alkylbenzene sulfonate (LAS) and a common analgesic (ibuprofen) increased with increasing triclosan concentrations (0.16-100 mg kg⁻¹). The largest effect was seen for LAS mineralization which was severely reduced by 0.16 mg kg⁻¹ of triclosan. Our findings indicate that environmentally realistic concentrations of triclosan may affect the efficiency of biodegradation in percolation systems.     

Sediment quality guidelines for copper and zinc for filter-feeding estuarine oysters?

Sediment quality guidelines (SQGs) assess the ability of bottom sediment to sustain healthy infauna and water quality guidelines (WQGs) provide protection for a designated percentage of aquatic species. Filter-feeding marine species, e.g. oysters and mussels, acquire food from particles in the water column and protection of these animals is not provided by SQGs or WQGs. The current work investigated the relationship between metal (Cu, Zn) concentrations in total and fine-fraction (<62.5 μm) surficial sediment digested in a range of acids and chelating agents and oyster tissue metal concentrations. A strong correlation between oyster tissue Cu and Zn concentrations and fine-fraction surficial sediment digested in 1 M HCl provided a sedimentary guideline which predicted tissue metal concentrations in oysters and established a level (<45 μg g⁻¹ and <1000 μg g⁻¹, respectively) for protecting oysters from exceeding human consumption levels (70 μg g⁻¹ and 1000 μg g⁻¹, respectively).     

Concentration of trace elements in feathers of three Antarctic penguins: Geographical and interspecific differences

Antarctica is often considered as one of the last pristine regions, but it could be affected by pollution at global and local scale. Concentrations of Al, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Cd and Pb were determinated by ICP-MS in feathers (n = 207 individuals) of gentoo, chinstrap and Adélie penguin collected in 8 locations throughout the Antarctic Peninsula (2006-2007). The highest levels of several elements were found in samples from King George Island (8.08, 20.29 and 1.76 μg g⁻¹ dw for Cr, Cu and Pb, respectively) and Deception Island (203.13, 3.26 and 164.26 μg g⁻¹ dw for Al, Mn and Fe, respectively), where probably human activities and large-scale transport of pollutants contribute to increase metal levels. Concentrations of Cr, Mn, Cu, Se or Pb, which are similar to others found in different regions of the world, show that some areas in Antarctica are not utterly pristine.     

Use of whole-body and subcellular Cu residues of Lumbriculus variegatus to predict waterborne Cu toxicity to both L. variegatus and Chironomus riparius in fresh water

We tested the use of whole-body and subcellular Cu residues (biologically-active (BAM) and inactive compartments (BIM)), of the oligochaete Lumbriculus variegatus to predict Cu toxicity in fresh water. The critical whole-body residue associated with 50% mortality (CBR₅₀) was constant (38.2-55.6 μg g⁻¹ fresh wt.) across water hardness (38-117 mg L⁻¹ as CaCO₃) and exposure times during the chronic exposure. The critical subcellular residue (CSR₅₀) in metal-rich granules (part of BIM) associated with 50% mortality was approximately 5 μg g⁻¹ fresh wt., indicating that Cu bioavailability is correlated with toxicity:subcellular residue is a better predictor of Cu toxicity than whole-body residue. There was a strong correlation between the whole-body residue of L. variegatus (biomonitor) and survival of Chironomus riparius (relatively sensitive species) in a hard water Cu co-exposure. The CBR₅₀ in L. variegatus for predicting mortality of C. riparius was 29.1-45.7 μg g⁻¹ fresh wt., which was consistent within the experimental period; therefore use of Cu residue in an accumulator species to predict bioavailability of Cu to a sensitive species is a promising approach.     

Aerobic degradation of tetrabromobisphenol-A by microbes in river sediment

This study investigated the aerobic degradation of tetrabromobisphenol-A (TBBPA) and changes in the microbial community in river sediment from southern Taiwan. Aerobic degradation rate constants (k₁) and half-lives (t_1/2) for TBBPA (50 μg g⁻¹) ranged from 0.053 to 0.077 d⁻¹ and 9.0 to 13.1 d, respectively. The degradation of TBBPA (50 μg g⁻¹) was enhanced by adding yeast extract (5 mg L⁻¹), sodium chloride (10 ppt), cellulose (0.96 mg L⁻¹), humic acid (0.5 g L⁻¹), brij 30 (55 μM), brij 35 (91 μM), rhamnolipid (130 mg L⁻¹), or surfactin (43 mg L⁻¹), with rhamnolipid yielding a higher TBBPA degradation than the other additives. For different toxic chemicals in the sediment, the results showed the high-to-low order of degradation rates were bisphenol-A (BPA) (50 μg g⁻¹) > nonylphenol (NP) (50 μg g⁻¹) > 4,4′-dibrominated diphenyl ether (BDE-15) (50 μg g⁻¹) > TBBPA (50 μg g⁻¹) > 2,2′,3,3′,4,4′,5,5′,6,6′-decabromodiphenyl ether (BDE-209) (50 μg g⁻¹). The addition of various treatments changed the microbial community in river sediments. The results also showed that Bacillus pumilus and Rhodococcus ruber were the dominant bacteria in the process of TBBPA degradation in the river sediments.