Fate of cancerostatic platinum compounds in biological wastewater treatment of hospital effluents

The present work focuses on the fate of two cancerostatic platinum compounds (CPC), cisplatin and carboplatin, as well as of two inorganic platinum compounds, [PtCl₄]²⁻ and [PtCl₆]²⁻ in biological wastewater treatment. Laboratory experiments modelling adsorption of these compounds onto activated sludge showed promising specific adsorption coefficients K_D and K_OC and Freundlich adsorption isotherms. However, the adsorption properties of the investigated substances were differing significantly. Adsorption decreased following the order cisplatin > [PtCl₆]²⁻ > [PtCl₄]²⁻ > carboplatin. Log K_D-values were ranging from 2.5 to 4.3 , log K_OC from 3.0 to 4.7.

A pilot membrane bioreactor system (MBR) was installed in a hospital in Vienna and fed with wastewater from the oncologic in-patient treatment ward to investigate CPC-adsorption in a sewage treatment plant. During three monitoring periods Pt-concentrations were measured in the influent (3–250 μg l⁻¹ Pt) and the effluent (2–150 μg l⁻¹ Pt) of the treatment plant using ICP-MS. The monitoring periods (duration 30 d) revealed elimination efficiencies between 51% and 63% based on averaged weekly input–output budgets. The derived log K_D-values and log K_OC-values ranged from 2.4 to 4.8 and from 2.8 to 5.3, respectively. Species analysis using HPLC-ICP-MS proofed that mainly carboplatin was present as intact drug in the influent and – due to low log K_D – in the effluent of the MBR.     

Characterization of atmospheric particulate and metallic elements at Taichung Harbor near Taiwan Strait during 2004-2005

Air aerosol samples for TSP (total suspended particulate), coarse particulate (particle matter with aerodynamical diameter 2.5–10 μm, PM_2.5–10), fine particulate (particle matter with aerodynamical diameter <2.5 μm, PM_2.5) and metallic elements were collected during March 2004 to January 2005 at TH (Taichung Harbor) in central Taiwan. The seasonal variation average concentration of TSP (total suspended particulate), coarse particulate (particle matter with aerodynamical diameter 2.5–10 μm, PM_2.5–10) and fine particulate (particle matter with aerodynamical diameter <2.5 μm, PM_2.5) were in the range 132–171.1 μg m⁻³ and 43–49.5 μg m⁻³, respectively. Seasonal variation of metallic elements Cu, Mn, Zn and Fe in the TSP (total suspended particulate) shows that higher concentration was observed during spring. Seasonal variation of metallic elements Pb, Cr and Mg in the TSP (total suspended particulate) shows that higher concentration was observed during winter. The average metallic element TSP (total suspended particulate) concentration order was Fe > Zn > Mg > Cu > Cr > Mn > Pb in spring. In addition, at the TH sampling site, the average concentration variation of TSP (total suspended particulate) displayed the following order: spring > winter > autumn > summer. However, the average concentration variation of coarse particulate (particle matter with aerodynamical diameter 2.5–10 μm, PM_2.5–10) displayed the following order: spring > winter > summer > autumn. Finally, the average concentration variations of fine particulate (particle matter with aerodynamical diameter <2.5 μm, PM_2.5) were in the following order: winter > spring > summer > autumn at the TH sample site.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

Efficient removal and mechanisms of water soluble aromatic contaminants by a reduced-charge bentonite modified with benzyltrimethylammonium cation

A novel strategy utilizing the phenyls interaction and the hydrophobic affinity of available siloxane surface in the interlayer of bentonite was proposed to improve the sorption capabilities of organobentonites for water soluble aromatic contaminants. A unique organobentonite (65BTMA) was synthesized by intercalating benzyltrimethylammonium cation (BTMA⁺) into the interlayer of a reduced-charge bentonite with cation exchange capacity (CEC) of 65 cmol kg⁻¹. Phenol, aniline and toluene were used as model compounds of water soluble aromatic contaminants. Their respective removal efficiencies by 65BTMA were achieved at 83.3%, 89.2% and 97.3% at the initial concentration of 20 mg l⁻¹. To reveal the sorption mechanism, sorption characteristics of aromatic contaminants to 65BTMA were compared with that of aliphatic contaminants in similar molecular size. And various organobentonites were prepared by combining TMA⁺ (tetramethylammonium), BTMA⁺, HTMA⁺ (heptyltrimethylammonium) and CTMA⁺ (cetyltrimethylammonium) with two bentonites (CEC = 108 and 65 cmol kg⁻¹). To 65BTMA, sorption magnitudes of aromatic contaminants were much greater than that of aliphatic compounds with similar size; and dramatically higher than those to other organobentonites at low pollutant concentrations. These observations revealed that the strong phenyls interactions contributed significantly to sorb the aqueous soluble aromatic contaminants to 65BTMA (>90%), and which favored to design uniquely powerful sorbents.     

Methane fluxes from tundra soils and snowpack in the maritime Antarctic

Methane fluxes were measured from three exposed tundra sites and four snowpack sites on the Fildes Peninsula in the maritime Antarctic in the summertime of 2002. The average fluxes at two normal tundra sites were −15.3 μg m⁻² h⁻¹ and −14.3 μg m⁻² h⁻¹, respectively. The fluxes from tundra site with fresh penguin dropping addition showed positive values with the average of 36.1 μg m⁻² h⁻¹, suggesting that the deposition of fresh droppings greatly enhanced CH₄ emissions from the poor Antarctic tundra during penguin breeding periods. The summertime variation in CH₄ flux was correlated with surface ground temperature and the precipitation. The correlation between the flux and PT₀, which is the product of the precipitation and surface ground temperature, was quite strong. The diurnal cycle of CH₄ flux from the tundra soils was not obtained due to local fluky weather conditions. The fluxes through four snowpack sites were also obtained by the vertical CH₄ concentration gradient and their average fluxes were −46.5 μg m⁻² h⁻¹, −28.2 μg m⁻² h⁻¹, −46.4 μg m⁻² h⁻¹ and −17.9 μg m⁻² h⁻¹, respectively, indicating that tundra soils under snowpack also consume atmospheric CH₄ in the maritime Antarctic; therefore these fluxes could constitute an important part of the annual CH₄ budget for Antarctic tundra ecosystem.     

Bioaccumulation of anthropogenic contaminants by detritivorous fish in the Río de la Plata estuary: 1-aliphatic hydrocarbons

The temporal variability and bioaccumulation dynamics of C_12–25 n-alkanes, isoprenoids and unresolved aliphatic hydrocarbons (UCM) were studied in a detritivorous fish (Sábalo: Prochilodus lineatus) collected from 1999 to 2005 in the sewage impacted Buenos Aires coastal area. Fish muscles contain huge amounts of n-C_12–25 (165 ± 93, 70 ± 48 or 280 ± 134 μg g⁻¹, dry, fresh and lipid weight, respectively) and UCM (931 ± 560, 399 ± 288 and 1567 ± 802 μg g⁻¹) reflecting the chronic bioaccumulation of fossil fuels from sewage particulates. On a temporal basis, lipid normalized aliphatic concentrations peaked by the end of 2001–2002 during the rainiest period over the last four decades (1750 vs. 1083 ± 4.6 mm in 1999, 2004 and 2005), reflecting an enhanced exposition due to massive anthropogenic fluxes from Metropolitan Buenos Aires in wet years. The hydrocarbon composition in fish muscles is enriched in n-C_15–17 and isoprenoids relative to a fresh crude oil and settling particulates, with fresher signatures during the 2001–2002 maxima. Fish/settling material bioaccumulation factors (BAFs: 0.4–6.4 dry weight or 0.07–0.94 lipid-organic carbon) plotted against K_ow showed a parabolic pattern maximizing at n-C_14–18 and isoprenoids. The optimal bioaccumulation window corresponds to highly hydrophobic (log K_ow: 7.2–9.9), intermediate-size C_14–18 n-alkanes and C_15–20 isoprenoids (MW: 198–282; length: 17.9 to 25.4 Å) with melting points ranging from −19.8 to 28 °C. The uptake efficiency is inversely correlated to melting points and increased from 75% for n-C₂₅ to above 90% for n-C_14–15 and isoprenoids.     

The use of physiological characteristics for comparison of organic compounds phytotoxicity

The influence of intact (FLT) and photomodified (phFLT) fluoranthene (0.05, 0.5 and 5 μmol l⁻¹) and herbicide Basagran (5, 20, 35 and 50 nmol l⁻¹) on the germination, growth of seedlings and photosynthetic processes in pea plants (Pisum sativum L., cv. Garde) was investigated. The germination was significantly inhibited already by the lowest concentration (0.05 μmol l⁻¹) of FLT and phFLT, while Basagran caused inhibition only in higher concentrations (35 and 50 nmol l⁻¹). The growth of roots was significantly inhibited by higher concentration 5 μmol l⁻¹ of both FLT and phFLT and the shoot of seedlings was significantly influenced only by photomodified form. The length of root and shoot was inhibited already by concentration 5 nmol l⁻¹ of Basagran. Organic compounds applied on chloroplasts suspension influenced primary photochemical processes of photosynthesis. In chlorophyll fluorescence parameters, the significant increase of F₀ values and the decrease of F_V/F_M and Φ_II values by application of FLT (0.5 and 5 μmol l⁻¹) and phFLT (0.05, 0.5 and 5 μmol l⁻¹) was recorded. The maximum capacity of PSII (F_V/F_M) was influenced by the highest (50 nmol l⁻¹) and the effective quantum yield of PSII (Φ_II) already by the lowest (5 nmol l⁻¹) concentration of Basagran. Hill reaction activity decreased and was significantly inhibited by higher concentration (0.5 and 5 μmol l⁻¹) of FLT and phFLT and already by the lowest concentration (5 nmol l⁻¹) of Basagran.     

Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste

The adsorption of thiocyanate onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q₀) was found to be 16.2 mg g⁻¹ of the adsorbent. The per cent adsorption was maximum in the pH range 3.0–7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as ΔG⁰, ΔH⁰ and ΔS⁰ for the adsorption were evaluated. The negative values of ΔH⁰ confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.     

Leaching and degradation of 21 pesticides in a full-scale model biobed

Filling and cleaning of pesticide sprayers presents a potential risk of pollution of soil and water. Three different solutions for handling sprayers have been suggested: Filling and cleaning in the field, filling and cleaning on hard surfaces with collection of the waste water, and filling and cleaning on a biobed, which is an excavation lined with clay and filled with a mixture of chopped straw, sphagnum and soil with turf on top, and with increased sorption capacity and microbial activity for degradation of the pesticides. In the present study the degradation and leaching of 21 pesticides (5 g of each) was followed in an established full-scale model biobed. Percolate was collected and analysed for pesticide residues, and the biobed material was sampled at three different depths and analysed by liquid chromatography double mass spectrometry (LC-MSMS). During the total study period of 563 days, no traces of 10 out of 21 applied pesticides were detected in the percolate (detection limits between 0.02 and 0.9 μg l⁻¹) and three pesticides were only detected once and at concentrations below 2 μg l⁻¹. During the first 198 days before second application, 14% of the applied herbicide bentazone was detected in the leachate with maximum and mean concentrations of 445 and 172 μg l⁻¹, respectively. About 2% of the initial mecoprop and fluazifop dose was detected in the percolate, with mean concentrations of 23 μg l⁻¹, while MCPA and dimethoate had mean concentrations of 3.5 and 4.7 μg l⁻¹, respectively. Leachate concentrations for the remaining pesticides were generally below the detection limit (0.02–0.9 μg l⁻¹, below 1% of applied). Sorption studies of five pesticides showed that compounds with a low K_d value appeared in the leachate. After 169 days, all pesticides in the biobed profile were degraded to a level below 50% of the calculated initial dose. Pesticides with K_oc values above 100 were primarily found in the uppermost 10 cm and degraded slowest due to the low bioavailability. The 11 most degradable pesticides were all degraded such that less than 3% remained in the biobed after 169 days.

Following second pesticide application of the biobed, leachate was sampled 215 and 365 days after the treatment. This showed the same pesticides to be leached out and at concentrations comparable to those of the first treatment. The same pesticides as after the first treatment were retained in the biobed.     

Concentrations of chlorine, bromine and iodine in Japanese rivers

Concentrations of halogens (Cl, Br and I) in 30 Japanese rivers were measured by ion chromatography and inductively coupled plasma mass spectrometry to understand their behavior in the terrestrial environment. Concentrations of Cl, Br and I in each river, obtained at 10 sampling points from the upper stream to the river mouth, tended to increase near the river mouth. The ranges of geometric means of Cl, Br and I in each river were 1.0–19.4 mg l⁻¹, 2.5–67.9 μg l⁻¹, and 0.18–8.34 μg l⁻¹, respectively. To compare halogen behavior, the concentration ratios, Br/Cl and I/Cl, were calculated. The Br/Cl range was (2.3–7.8) × 10⁻³ (geometric mean: 3.74 × 10⁻³), and it was nearly constant except for the Yoneshiro river. It was estimated that 60–80% of total Br in the middle to lower parts of this river was the excess Br. The Br chemical form in all the rivers is generally considered to be Br⁻. The I/Cl ratios had different trends in rivers flowing into the Japan Sea and Pacific Ocean, possibly due to the different geological features in the river catchments.     

Copper complexation by tannic acid in aqueous solution

The speciation of titrated copper in a dissolved tannic acid (TA) solution with an initial concentration of 4 mmol organic carbon (OC)/l was investigated in a nine-step titration experiment (Cu/OC molar ratio = 0.0030–0.0567). We differentiated between soluble and insoluble Cu species by 0.45 μm filtration. Measurements with a copper ion selective electrode (ISE) and diffusive gradients in thin films (DGT) were conducted to quantify unbound Cu(II) cations (‘free’ Cu) and labile soluble Cu complexes. For the DGT measurements, we used an APA hydrogel and a Chelex 100 chelating resin (Na form). Insoluble organic Cu complexes (>0.45 μm) was the dominant Cu species for Cu/OC = 0.0030–0.0567 with a maximum fraction of 0.96 of total Cu. At Cu/OC > 0.0100, Cu-catalysed degradation of aggregate structures resulted in a strong increase of free Cu and (labile) soluble Cu complexes with a maximum fraction of 0.28 and 0.32 of total Cu, respectively. Labile (i.e. DGT-detectable) soluble Cu complexes had a relatively high averaged diffusion coefficient (D) in the APA hydrogel (3.50 × 10⁻⁶– 5.58 × 10⁻⁶ cm² s⁻¹).     

Octyl and nonylphenol ethoxylates and carboxylates in wastewater and sediments by liquid chromatography/tandem mass spectrometry

This work presents an LC–MS–MS-based method for the quantitation of nonylphenol ethoxylates (NPEOs) and octylphenol ethoxylates (OPEOs) in water, sediment, and suspended particulate matter, and three of their carboxylated derivatives in water. The alkylphenol ethoxylates (APEOs) were analyzed using isotope dilution mass spectrometry with [¹³C₆]-labeled analogues, whereas the carboxylated derivatives were determined by external standard quantitation followed by confirmation using standard additions. The method was used to study APEO’s behavior in a wastewater treatment plant (WWTP), where total dissolved NP0-16EO concentration was reduced by approximately 99% from influent (390 μg l⁻¹) to final effluent (4 μg l⁻¹), and total OP0-5EO concentration decreased by 94% from 3.1 to 0.2 μg l⁻¹. In contrast, the carboxylated derivatives were formed during the process with NP0-1EC concentrations increasing from 1.4 to 24 μg l⁻¹. Short-chain APEOs were present in higher proportions in particulate matter, presumably due to greater affinity for solids compared to the long-chain homologues. NP (0.49 μg l⁻¹) and NP0-1EC (4.8 μg l⁻¹) were the only APEO-related compounds detected in a surface water sample from a WWTP-impacted estuary; implying that 90% of the mass was in the form of carboxylated derivatives. Sediment analysis showed nonylphenol to be the single most abundant compound in sediments from the Baltimore Harbor area, where differences in homologue distribution suggested the presence of treated effluent in some of the sites and non-treated sources in the rest.     

A chemical and toxicological profile of Dutch North Sea surface sediments

Chemical and toxicological profiles were assessed in surface sediments (fraction <63 μm) from the southern North Sea. In extracts of freeze-dried samples, polybrominated biphenyl (PBB), Irgarol 1051 and phthalate concentrations were below the respective detection limits (except di(2-ethylhexyl)phthalate, which was between 170 and 3300 μg kg⁻¹ dry weight (dw)). Hexabromocyclododecane (HBCD) concentrations were between 0.8 and 6.9 μg kg⁻¹ dw, with highest concentrations at river mouths. Polybrominated diphenylethers (PBDE) concentrations were 0.4–0.6 μg kg⁻¹ dw, decabromodiphenylether (BDE209) 1–32 μg kg⁻¹ dw. The ratio BDE209/PCB153 was used as a tracer for recent emissions, and pointed towards a BDE209 source in the Western Scheldt’s upper estuary. PCBs and PAHs were between 0.19–4.7 and 2.6–200 μg kg⁻¹ dw respectively and generally had highest concentrations at near-shore locations and river mouths.

Responses in the Microtox broad-spectrum and the Mutatox genotoxicity assays were generally low, with near-shore locations giving higher responses. The umu-C genotoxicity and the ER-CALUX assay for estrogenicity showed no response, with the exception of one near-shore location (IJmuiden outer harbour, ER-CALUX).

Highest dioxin-like toxicity (DR-CALUX) was found at near-shore locations, in the outflow of the Rhine/Meuse estuary including a dumping site of harbour sludge. At the Oyster Grounds, DR-CALUX responses appeared to be linked to the occurrence of larger PAHs (4–6 rings). A new, non-destructive clean up procedure resulted in significantly higher DR-CALUX responses than the current protocol. The Dutch legislation on disposal of harbour sludge at sea, dictates the use of the conventional clean up procedure. Our results therefore indicate that probably more dioxin-like toxicity associated with harbour sludge is disposed off at sea than assumed.     

Impacts of charcoal characteristics on sorption of polycyclic aromatic hydrocarbons

Sorption of three polycyclic aromatic hydrocarbons (PAHs, phenanthrene, anthracene and pyrene) on three charcoals and their precursor substance (sawdust) was studied. The charcoals obtained by heating at 400 °C for different periods were different in chemical composition and structure. Sorption characteristics were described by a Polanyi–Dubinin–Manes model combined with poly-parameter linear free energy relationships. The results revealed that though partition could not be neglected for sawdust and charcoal containing large sawdust residue, adsorption controlled the sorption of PAHs on matured charcoals, where π–π electron donor–acceptor (EDA) exerted as the main molecular-scale interactions. Charring elevated partition coefficients (K_oc) of the three PAHs more than one order of magnitude, which ranged from 10^5.74 to 10^6.58 on charcoals (for PAHs at equilibrium concentration C_e = 0.005S_w). Adsorption increased with the aromaticity of the charcoals, however, polar aromatic structure may stimulate sorption of PAHs due to the presence of π–π EDA interactions.     

Removal of a cationic dye from aqueous solutions by adsorption onto bentonite clay

The ability of bentonite to remove malachite green from aqueous solutions has been studied for different adsorbate concentrations by varying the amount of adsorbent, temperature, pH and shaking time. Maximum adsorption of the dye, i.e. >90% has been achieved in aqueous solutions using 0.05 g of bentonite at a pH of 9. Thermodynamic parameters such as ΔH°, ΔS° and ΔG° were calculated from the slope and intercept of the linear plots of ln K_D against 1/T. Analysis of adsorption results obtained at 298, 308, 318 and 328 K showed that the adsorption pattern on bentonite seems to follow the Langmuir, Freundlih and D–R isotherms. The temperature increase reduces adsorption capacity by bentonite, due to the enhancement of the desorption step in the mechanism. The numerical values of sorption free energy (E_a) of 1.00–1.12 kJ mol⁻¹ indicated physical adsorption. The kinetic data indicated an intraparticle diffusion process with sorption being first order. The rate constant k was 0.526 min⁻¹. The concentration of malachite green oxalate was measured before and after adsorption by using UV–Vis spectrophotometer.     

Study on the fluorescence characteristics of bromadiolone in aqueous and organized media and application in analysis

The fluorescence spectroscopic behavior of bromadiolone (anticoagulant rodenticide), a substituted 4-hydroxycoumarin derivative, was investigated in water and in organized media like micelles and cyclodextrins. A detailed study on various photophysical parameters like fluorescence intensity (I_F), quantum yield (), lifetime (τ) and steady state fluorescence anisotropy (r) of bromadiolone in aqueous and in organized media was carried out. Bromadiolone in aqueous solution was observed to be in an aggregated state, thereby showing weak emission due to self-quenching. Marked enhancement of fluorescence intensity was observed in organized media like micelles and β-cyclodextrin. A preliminary investigation has been done to find out whether this enhancement of fluorescence can be used to develop a sensitive analytical method for determination of bromadialone in aqueous media. A linear relationship between the fluorescence intensity and concentration of bromadiolone was observed in the range of 0.15–7.9 μg ml⁻¹ in cetyltrimethylammonium bromide (CTAB) and 0.5–26.4 μg ml⁻¹ in β-cyclodextrin medium. The lower detection limit was found to be 37 ng ml⁻¹ in presence of CTAB and 23 ng ml⁻¹ in β-cyclodextrin. Comparison with 4-hydroxycoumarin, an unsubstituted analogue, was made.     

Isoprene emission from tropical trees in Okinawa Island, Japan

This study surveyed isoprene emission from 42 indigenous and exotic tropical trees in subtropic Okinawa, Japan. Of the 42 trees studied, 4 emitted isoprene at a rate in excess of 20 μg g⁻¹ h⁻¹, and 28 showed the rates of 1–10 μg g⁻¹ h⁻¹. The remainder emitted less than 1 μg g⁻¹ h⁻¹. The majority of trees in this study may therefore fall within the lower emitting species. However, species in Moraceae that is indigenous in Okinawa emitted isoprene at relatively higher rates with an average of 14.2 μg g⁻¹ h⁻¹. The highest emission rate of 107.1 μg g⁻¹ h⁻¹ for Ficus virgata yielded the area basis rate of 47.4 nmol m⁻² s⁻¹, which is almost equivalent to the rate of high emitting species. Furthermore, a linear relationship between light intensity and isoprene emission was noted with Ficus virgata up to 1700 μmol m⁻² s⁻¹. These findings may show the potential importance of subtropical areas as sources of isoprene to the atmosphere.     

Cold season CH4, CO2 and N2O fluxes from freshwater marshes in northeast China

Cold season (winter and thaw) CH₄, CO₂ and N₂O fluxes from freshwater marshes (47°35′N, 133°31′E, Northeast China) were measured, using the static chamber method. The mean CH₄ and CO₂ fluxes from Carex lasiocarpa (Cl) were 0.5 ± 0.19 and 6.23 ± 1.36 mg C m⁻² h⁻¹, respectively, and those from Deyeuxia angustifoli (Da) were 0.18 ± 0.15 and 5.22 ± 2.48 mg C m⁻² h⁻¹, respectively in winter. There was no significant difference between Cl and Da (p > 0.05). The contributions of winter CH₄ fluxes were about 5.5% and 3% in the Cl and Da, respectively. Marshes are an important potential N₂O sink in winter season in northeast China. During thaw, the CH₄ and CO₂ emissions rapidly increased, 4.5–6 times of winter emissions. Wetland became a source of N₂O. Cold season gases flux from northern wetlands play an important role in the seasonal gas exchange.     

Compound-specific chlorine isotope analysis of polychlorinated biphenyls isolated from Aroclor and Clophen technical mixtures

The combined electrochemical oxidation-solar-light/immobilized TiO₂ film process was conducted to degrade an azo dye, Reactive Black 5 (RB5). The toxicity was also monitored by the Vibrio fischeri light inhibition test. The electrochemical oxidation rapidly decolorized RB5 (55, 110 μM) with a supporting electrolyte of 2 g l⁻¹ NaCl at current density 277 A m⁻² and pH 4. However, TOC mineralization and A₃₁₀ removal were low. Additionally, the treated solution showed high biotoxicity. RB5 at 110 μM significantly retarded the de-colorization efficiency by using the solar-light/immobilized TiO₂ film process. The combined electrochemical oxidation-solar-light/immobilized TiO₂ process effectively increased the removal of color, A₃₁₀, and TOC. The toxicity was also significantly reduced after 3 h of solar irradiation. The results indicated that the low-cost combined process is a potential technique for rapid treatment of RB5.     

Monoterpene emissions and carbonyl compound air concentrations during the blooming period of rape (Brassica napus)

An increasing percentage of agricultural land in Germany is used for oil seed plants. Hence, rape has become an important agricultural plant (in Saxony 1998: 12% of the farmland) in the recent years. During flowering of rape along with intensive radiation and high temperatures, a higher production and emission of biogenic VOC was observed. The emissions of terpenes were determined and more importantly, high concentrations of organic carbonyl compounds were observed during this field experiment. All measurements of interest have been carried out during two selected days with optimal weather conditions. It is found that the origin or the mechanism of formation of different group of compounds had strong influence on the day to day variation of their concentrations. The emission flux of terpenes from flowering rape plants was determined to be 16–32 μg h⁻¹ m⁻² (30–60 ng h⁻¹ per g dry plant––540–1080 ng h⁻¹ per plant), in total. Limonene, -thujene and sabinene were the most important compounds (about 60% of total terpenes). For limonene and sabinene reference emission rates (M_S) and temperature coefficients were determined: β_limonene=0.108 K⁻¹ and M_S=14.57 μg h⁻¹ m⁻²; β_sabinene=0.095 K⁻¹ and M_S=5.39 μg h⁻¹ m⁻².

The detected carbonyl compound concentrations were unexpectedly high (maximum formaldehyde concentration was 18.1 ppbv and 3.4 ppbv for butyraldehyde) for an open field. Possible reasons for these concentrations are the combination of primary emission from the plants induced by high temperature and high ozone stress, the secondary formation from biogenically and advected anthropogenically emitted VOC at high radiation intensities and furthered by the low wind speeds at this time.