活性碳纤维吸附处理对硝基苯酚生产废水

采用活性碳纤维(ACF)吸附处理对硝基苯酚(PNP)生产废水,考察了动态吸附和脱附过程.实验结果表明,在298 K、pH 4时,最佳进水流量为0.25 L/h,ACF的有效吸附量为439.3 mg/g,PNP去除率大于99.95%,TOC去除率大于99.5%,脱附率大于99.5%,ACF的吸附--脱附性能稳定.ACF吸附和电解相结合的工艺能有效去除废水中的有害物质,回收利用PNP和氯化钠,实现了PNP的清洁生产.     

树脂吸附法处理对氨基苯酚废水

采用自制的NDA-99特种复合功能树脂处理对氨基苯酚（PAP）生产废水，考察了各种因素对吸附和脱附效果的影响。小试实验结果得出的工艺条件为：吸附流量2．0BV／h，吸附温度15℃，单柱吸附量10BV；脱附剂为2BV盐酸（质量分数1．5％）＋2BV水。中试试验结果表明，在上述工艺条件下，NDA-99树脂处理PAP废水的吸附性能和脱附性能稳定，平均COD去除率约为93％，平均PAP脱附率达98％。     

活性炭纤维吸附模拟废气中的乙醇和乙醚

采用动态吸附法研究了5种活性炭纤维（ACF）对乙醇、乙醚及模拟混合废气中的乙醇和乙醚的吸附性能。实验结果表明：当ACF-1，ACF-2，ACF-3，ACF-4分别吸附乙醇和乙醚时，在室温、乙醇质量浓度12.0 mg/L、乙醚质量浓度13.0 mg/L的条件下，4种ACF对乙醇的穿透吸附量和饱和吸附量分别为60~70 mg/g和339~409 mg/g，对乙醚的穿透吸附量和饱和吸附量分别为50~65 mg/g和301~344 mg/g；在室温、模拟混合废气中乙醇和乙醚的质量浓度均为11.6 mg/L、吸附时间120 min的条件下，具有较大的比表面积和微孔体积的ACF-5对乙醇的吸附量为205 mg/g，对乙醚的吸附量为223 mg/g；在脱附真空度-0.95 Pa、脱附时间20 min的条件下，经17 次使用的ACF-5对模拟混合废气中乙醇和乙醚的穿透吸附量均为87 mg/g，穿透时间均为12 min。     

负载金属改性活性炭纤维的脱硫性能

采用浸渍法将金属负载到活性炭纤维(ACF)上对其进行改性,研究了负载金属改性ACF对模型油(二苯并噻吩-正辛烷)的吸附脱硫效果,对比了不同单金属和复合金属盐改性ACF的脱硫性能。实验结果表明:Ag和Zn复合改性的ACF具有最好的脱硫性能;在吸附温度为40℃,吸附时间为2.5 h,油剂质量比为21.5的优化条件下,脱硫率高达97.55%,且具有良好的重复利用性。     

用废炭黑吸附处理二苯胺生产废水

利用制氢生产中产生的废炭黑作吸附剂,对二苯胺生产废水中的苯胺进行吸附,找出了较佳吸附条件和脱附方法,试验表明,用废炭黑吸附处理二苯胺生产废水具有吸附速度快,吸附效果好,处理费用等优点。     

自制ZSM-5分子筛对甲苯气体的吸附-脱附性能

考察了自制ZSM-5分子筛对甲苯气体的吸附-脱附性能，并与市售MCM-22分子筛进行了对比实验。实验结果表明:在吸附温度为25℃、进口甲苯质量浓度为840mg/m3、吸附气体流速为0.016m/s、床层高度为15cm的条件下，出口甲苯质量浓度达到0.8mg/m3时的穿透时间为82min，吸附效率为4.26mg/g;在脱附温度为80℃、脱附气体流速为0.016m/s的条件下，脱附35min时出口甲苯质量浓度达到最大，为1220mg/m3。自制ZSM-5分子筛的吸附-脱附性能优于市售MCM-22分子筛。     

NDA-66树脂对邻苯二甲酸的吸附及脱附性能

研究了NDA-66新型超高交联树脂对邻苯二甲酸的吸附及脱附性能。实验结果表明:静态吸附过程中,在初始邻苯二甲酸质量浓度1 000 mg/L、溶液pH=2.0、吸附时间600 min的条件下,吸附量可达190 mg/g;动态吸附过程中,处理11吸附床层体积倍数(BV)的邻苯二甲酸溶液,当溶液流量为1.5 BV/h时,吸附率可达100%;动态脱附过程中,在w(NaOH)=6%、脱附温度328 K的最佳脱附条件下,脱附率可达99%以上。     

NDA-66树脂对邻苯二甲酸的吸附及脱附性能

研究了NDA-66新型超高交联树脂对邻苯二甲酸的吸附及脱附性能。实验结果表明：静态吸附过程中，在初始邻苯二甲酸质量浓度1 000 mg/L、溶液pH=2.0、吸附时间600 min的条件下，吸附量可达190 mg/g；动态吸附过程中，处理11吸附床层体积倍数（BV）的邻苯二甲酸溶液，当溶液流量为1.5 BV/h时，吸附率可达100%；动态脱附过程中，在w（NaOH）= 6%、脱附温度328 K的最佳脱附条件下，脱附率可达99%以上。     

活性碳纤维改性技术研究进展

介绍了活性碳纤维(ACF)的孔结构及表面官能团,综述了国内外ACF改性技术的研究现状.ACF的改性主要包括孔结构调控和表面化学改性,表面化学改性包括氧化还原法、表面负载法、浸渍法、热处理法、远程等离子体处理法、微波辐照法等,也可将多种方法结合来对ACF进行改性,以改善和提高ACF的吸附性能.在总结现有研究的基础上,对ACF改性技术发展趋势进行了展望.     

HZ-16型大孔树脂吸附处理含RDT-8废水

采用HZ-16型大孔树脂对含三（三溴苯氧基）三嗪（RDT-8）废水进行吸附及脱附处理。实验结果表明：在废水流量为4.0 BV/h的条件下，树脂最佳吸附工艺条件为出水体积88.0 BV，此条件下出水COD小于291 mg/L，挥发酚质量浓度小于0.08 mg/L；在脱附液流量为0.5 BV/h的条件下，树脂最佳脱附工艺条件为脱附液体积3.0 BV，此条件下脱附液中挥发酚质量浓度为30.6 mg/L，挥发酚脱附率高达76.4%。在最佳吸附-脱附工艺条件下，连续进行10次动态吸附-脱附实验，吸附出水中COD为137~294 mg/L，COD去除率为72.5%~89.1%，挥发酚质量浓度稳定在0.05 mg/L以下，挥发酚去除率为99.8%~100%，说明HZ-16型大孔树脂的吸附-脱附性能稳定。     

无黏结剂ZSM-5分子筛的制备及其对甲苯的吸附性能

以硅溶胶为黏结剂，将粗孔硅胶、聚乙二醇、拟薄水铝石、ZSM-5晶种导向剂捏条成型，采用干胶转化法制备得到了无黏结剂ZSM-5分子筛。XRD和SEM等表征方法的结果显示，采用干胶转化法制备得到的ZSM-5分子筛的相对结晶度较高，具有200nm左右的小晶粒构成的自支撑结构。采用无黏结剂ZSM-5分子筛吸附剂进行甲苯吸附-脱附实验，该吸附剂表现出良好的吸附性能，对甲苯的脱附性能优于活性炭。     

新型吸附材料AGS在油气回收中的应用

考查了自制疏水性硅胶吸附材料AGS在加油站模拟油气回收装置及某油库现场油气回收装置的应用效果，并与常用的柱状活性炭进行了比较。实验结果表明：与活柱状性炭相比，AGS对油气的吸附速率和吸附量较小，但是油气脱附效果更好；将二者混合得到的吸附材料同时具备二者的优点，既具有较高的油气吸附量又具有良好的脱附性能，使油气回收装置具有更大的油气吸附量和更好的回收效果。     

用活性炭纤维吸附处理十三吗啉农药废水的研究

介绍用活性炭纤维处理十三吗啉农药废水的工艺过程。研究了活性碳纤维对该种有机废水的吸附规律及脱附再生方法，并探索了其使用寿命。实验表明，用活性炭纤维处理十三吗啉农药废水，ＣＯＤｃｒ由２４６２ｍｇ／Ｌ可降至１５０ｍｇ／Ｌ以下，净化率达９４％。     

活性炭吸附黏胶纤维生产废气中的CS2

分别采用静态吸附和柱穿透吸附研究了活性炭对黏胶纤维生产废气中CS₂的吸附性能,考察了温度、水蒸气含量和预吸附H₂S时间对活性炭吸附CS₂效果的影响。实验结果表明：活性炭静态吸附CS₂的吸附等温线可用D-R方程很好地拟合,吸附温度升高,活性炭对CS₂的吸附量降低;Y-N方程能很好地拟合CS₂在活性炭上的柱吸附穿透过程,吸附温度升高,CS₂在活性炭上的吸附穿透时间缩短;进气水蒸气含量增大,吸附穿透时间缩短;预吸附H₂S时间延长,活性炭对CS₂的吸附穿透时间缩短;脱附温度升高,CS₂脱附率和脱附速率均加快。     

Siloxanes removal from biogas by high surface area adsorbents

Biogas utilized for energy production needs to be free from organic silicon compounds, as their burning has damaging effects on turbines and engines; organic silicon compounds in the form of siloxanes can be found in biogas produced from urban wastes, due to their massive industrial use in synthetic product, such as cosmetics, detergents and paints.Siloxanes removal from biogas can be carried out by various methods (Mona, 2009, Ajhar et al., 2010, Schweigkofler and Niessner, 2001); aim of the present work is to find a single practical and economic way to drastically and simultaneously reduce both the hydrogen sulphide and the siloxanes concentration to less than 1 ppm. Some commercial activated carbons previously selected (Monteleone et al., 2011) as being effective in hydrogen sulfide up taking have been tested in an adsorption measurement apparatus, by flowing the most volatile siloxane (hexamethyldisiloxane or L2) in a nitrogen stream, typically 100–200 ppm L2 over N₂, through an activated carbon powder bed; the adsorption process was analyzed by varying some experimental parameters (concentration, grain size, bed height). The best activated carbon shows an adsorption capacity of 0.1 g L2 per gram of carbon. The next thermogravimetric analysis (TGA) confirms the capacity data obtained experimentally by the breakthrough curve tests.The capacity results depend on L2 concentration. A regenerative carbon process is then carried out by heating the carbon bed up to 200 °C and flushing out the adsorbed L2 samples in a nitrogen stream in a three step heating procedure up to 200 °C. The adsorption capacity is observed to degrade after cycling the samples through several adsorption–desorption cycles.     

Characteristics of mercury desorption from sorbents at elevated temperatures

This study investigated the dynamic desorption characteristics of mercury during the thermal treatment of mercury-loaded sorbents at elevated temperatures under fixed-bed operations. Experiments were carried out in a 25.4 mm ID quartz bed enclosed in an electric furnace. Elemental mercury and mercuric chloride were tested with activated carbon and bauxite. The experimental results indicated that mercury desoption from sorbents was strongly affected by the desorption temperature and the mercury–sorbent pair. Elemental mercury was observed to desorb faster than mercuric chloride and activated carbon appeared to have higher desorption limits than bauxite at low temperatures. A kinetic model considering the mechanisms of surface equilibrium, pore diffusion and external mass transfer was proposed to simulate the observed desorption profiles. The model was found to describe reasonably well the experimental results.     

Activated carbon from Ceiba pentandra hulls, an agricultural waste, as an adsorbent in the removal of lead and zinc from aqueous solutions

The ability of low-cost activated carbon prepared from Ceiba pentandra hulls, an agricultural waste material, for the removal of lead and zinc from aqueous solutions has been investigated. In the batch tests experimental parameters were studied, including solution pH, contact time, adsorbent dose and initial metal ions concentration. The adsorbent exhibited good sorption potential at pH 6.0. Maximum removal of lead (99.5%) and of zinc (99.1%) with 10 g/l of sorbent was observed at 50 mg/L sorbate concentration. Removals of about 60-70% occurred in 10 min, and equilibrium was attained at around 50 min for both metals. The functional groups (CO, SO,-OH) present on the carbon surface were responsible for the adsorption of metal ions. The adsorption parameters were analysed using both the Freundlich and Langmuir models. The data are better fitted by the Freundlich isotherm as compared to Langmuir model, and the adsorption capacities for lead and zinc were 25.5 and 24.1 mg/g, respectively. Kinetics of adsorption obeyed a second order rate equation and the rate constant was found to be 2.71 x 10(-2) and 2.08 x 10(-2) g/mg/min for lead and zinc, respectively. The desorption studies were carried out using dilute HCl, and the effect of HCl concentration on desorption was studied. Maximum desorptions of 85% for lead and 78% for zinc were attained with 0.15 M HCl.     

Uptake of dyes by a promising locally available agricultural solid waste: coir pith

The adsorption of rhodamine-B and acid violet by coir pith carbon was carried out by varying the parameters such as agitation time, dye concentration, adsorbent dose and pH. The adsorption followed both Langmuir and Freundlich isotherms. The adsorption capacity was found to be 2.56 mg and 8.06 mg dye per g of the adsorbent for rhodamine-B and acid violet, respectively. Adsorption of dyes followed first order rate kinetics. Acidic pH was favorable for the adsorption of acid violet and alkaline pH was favorable to rhodamine-B. Desorption studies showed that alkaline pH was favorable for the desorption of acid violet and acidic pH was favorable for the desorption of rhodamine-B.     

苯乙烯废水活性炭吸附装置的评价及改进研究

对抚顺石化公司化工塑料厂苯乙烯废水活性炭吸附装置的预处理设施、活性炭吸附及再生性能进行了评价，分析了出水水质超标的主要原因，用混凝沉淀－砂滤流程改进了原处理工艺，使出水水质得到了显著改善。     

Optimizing Cr(VI) adsorption on activated carbon produced from heavy oil fly ash

In order to explore the beneficial utilization of heavy oil fly ash (HOFA) generated in the power plants, the present study is intended to optimize the chromium(VI) [Cr(VI)] adsorption on activated carbon produced from HOFA. The raw HOFA obtained from a power plant was washed by nitric/hydrochloric acid and activated at 800 °C with a holding time of 60 min to produce fly ash activated carbon (FAC). Phosphoric acid was used as a chemical agent to improve the surface characteristics of the HOFA during the activation process. Batch adsorption experiments were employed to evaluate the effects of different parameters such as initial Cr(VI) concentration, pH, and FAC dose on the removal of Cr(VI) from aqueous solution. A total of 17 adsorption experimental runs were carried out employing the detailed conditions followed the response surface methodology based on the Box–Behnken design. The results indicate that developed FAC has the potential for removing Cr(VI) from wastewater. Under the test conditions, a maximum of 91.51 % Cr(VI) removal efficiency was achieved.