粉煤灰处理阴离子表面活性剂废水及机理研究

采用粉煤灰作为吸附混凝剂,研究了粉煤灰对废水中阴离子表面活性剂十二烷基磺酸钠（SDS）的去除及机理。分析了粉煤灰投加量、吸附时间、pH值对废水中SDS去除率的影响,探讨了最佳条件下废水中SDS去除率,研究了粉煤灰动力学特征。结果表明,在200mL浓度50mg/L的SDS溶液中,调节pH值为13,加入70 g粉煤灰,搅拌20m in后,SDS的去除率为83.3%。粉煤灰对SDS的吸附符合Freund lich吸附等温式。     

粉煤灰对造纸废液的吸附脱色和去除COD的实验研究

以造纸废液为处理对象,研究了粉煤灰对造纸废液的吸附脱色和去除COD的作用、效果和机理。实验结果表明:粉煤灰符合作为吸附剂的要求。当采用静态搅拌吸附处理时,低pH值,高灰水比和较高的稀释倍数对熙液的处理有利。若再通过滤层,则可使几种完全脱色,COD去除率也显著提高。     

粉煤灰活性污泥法试验研究

以印染废水为处理对象,研究了粉煤灰活性污泥法(FAT法)的作用、处理效果和机理。试验结果表明,投加粉煤灰0.5克/升,脱色率提高20％,继续增加投加量效果会更好,一般粉煤灰投加量0.5—3.0克/升为宜。粉煤灰还可有效地改善活性污泥的沉降性能,克服污泥膨胀。MLSS1400毫克/升的活性污泥中投加3克/升粉煤灰,沉降速度SV_(30)从85下降到35,污泥容积指数SVI从600下降到75。显微镜观察证明粉煤灰的作用是物理作用。     

粉煤灰的改性及其吸附性能

以改性粉煤灰为吸附剂,对亚甲基蓝溶液进行吸附实验。经正交实验确定改性粉煤灰的最佳制备条件:煅烧温度为850℃,粉煤灰与ZnCl2的质量比为2∶2,盐酸加入量为2.4mol/L,粉煤灰粒径为16.8mm。在亚甲基蓝溶液初始质量浓度为10mg/L、改性粉煤灰加入量为200mg/L、振荡时间为3.0h、溶液pH为5、吸附温度为25℃的条件下,亚甲基蓝的降解率和溶液脱色率分别达86.24%和82.76%。     

无机-有机复合絮凝剂PACSAM的制备及其脱色性能

以聚合氯化铝（PAC）和淀粉-丙烯酰胺接枝聚合物（ST-AM）为原料,合成了一种新型的无机-有机复合絮凝剂（PACSAM）。考察了PACSAM对活性染料、直接染料模拟印染废水及实际印染废水的脱色效果,并初步探讨了絮凝机理。实验结果表明：在很宽的pH范围内,PACSAM均表现出了良好的脱色性能;在PACSAM加入量为25m g/L时,PACSAM对实际印染废水的脱色率、COD去除率、浊度去除率分别为96.4%,92.1%,98.5%,废水处理效果明显好于壳聚糖和PAC。PACSAM的絮凝机理包括化学反应、分子间氢键、电中和及架桥作用等。     

一种染料母液废水的吸附脱色研究

选取10种廉价材料对活性染料母液废水进行吸附脱色,结果显示,7种生物质材料脱色效果相对较好,其中橡树叶脱色效率达14.6%.选取橡树叶进行操作条件的优化,结果显示,低pH有利于染料的吸附;脱色率随吸附剂投加量的增加而增高;吸附剂的一次投加优于多次投加;改性处理后脱色效率超过50%.     

新生二氧化锰吸附法去除水中直接大红染料

研究了影响新生MnO2对直接大红4B染料废水脱附脱色的有关因素，结果表明，pH是影响脱色效果的关键因素，吸附脱色存在佳化pH范围，其上限随染料浓度的提高和MnO2投加量的增加而增大。投加0．3g/L的MnO2可使染料废水的脱色率达到98．2％，升高温度可提高脱色率。     

改性粉煤灰混凝剂处理工业混合废水的试验研究

通过混合酸、氯化钠制备改性粉煤灰混凝剂,探讨粉煤灰粒度、酸用量、加热时间、反应温度等对废水处理效果的影响,得出制备混凝剂最佳工艺方案。通过正交试验,用最佳混凝剂处理工业混合废水,找出混凝剂投量、废水pH值、搅拌时间及静置时间等最佳参数,探索一条以废治废的可行方法。     

水性油墨废水絮凝污泥制备吸附剂及阳离子染料的吸附

以水性油墨废水絮凝污泥为原料、采用一步炭化活化法制备了吸附剂,并将其用于阳离子蓝X-GRRL溶液(300 mg/L)的吸附处理。考察了吸附剂投加量、吸附时间、吸附温度和吸附pH对吸附效果的影响,并对吸附动力学进行了探讨。结果表明:所制得吸附剂的总孔体积为0.5 cm~3/g,平均孔径为7.12 nm;在吸附剂投加量0.6g/L、吸附时间420 min、吸附温度25℃、吸附pH 5.4的条件下,吸附量高达486.21 mg/g,脱色率达97.24%;该吸附剂对于阳离子蓝X-GRRL的吸附过程可用准二级动力学模型和颗粒内扩散效应模型很好地描述。     

水溶性染料废水的厌氧生物脱色

从取自染料生产废水处理厂的厌氧污泥中驯化、培养出混合高效脱色菌,研究其对水溶性染料废水的脱色工艺条件及脱色广谱性.实验结果表明:对活性红X-3B染料废水,当废水pH为7.5、反应温度为35℃、不另外投加N和P时,处理12h以上,脱色效果良好;不同结构水溶性染料的废水的脱色效果不同;在最佳脱色工艺条件下,选育的混合脱色菌对多种不同种类的水溶性染料废水均具有较高的脱色率.     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％；靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.