Leaching behaviour of waste and stabilized waste materials; characterization for environmental assessment purposes

The importance of systematic trends in trace contaminant leaching from waste materials and stabilized waste is stressed. Similarities in leaching behaviour of different waste materials and mechanisms for leaching from stabilized waste forms are identified. The use of diffusion measurements to quantify the mobility of specific chemical species in waste and soil is discussed. Implementation of more fundamental regulatory testing procedures which reflect the behaviour of materials in end use applications, is recommended to allow better control over environmental impact in the wide variety of utilization and disposal practices.     

Separate collection of household food waste for anaerobic degradation - Comparison of different techniques from a systems perspective

Four systems for household food waste collection are compared in relation the environmental impact categories eutrophication potential, acidification potential, global warming potential as well as energy use. Also, a hotspot analysis is performed in order to suggest improvements in each of the compared collection systems. Separate collection of household food waste in paper bags (with and without drying prior to collection) with use of kitchen grinders and with use of vacuum system in kitchen sinks were compared. In all cases, food waste was used for anaerobic digestion with energy and nutrient recovery in all cases. Compared systems all resulted in net avoidance of assessed environmental impact categories; eutrophication potential (-0.1 to -2.4kg NO(3)(-)eq/ton food waste), acidification potential (-0.4 to -1.0kg SO(2)(-)eq/ton food waste), global warming potential (-790 to -960kg CO(2)(-)eq/ton food waste) and primary energy use (-1.7 to -3.6GJ/ton food waste). Collection with vacuum system results in the largest net avoidence of primary energy use, while disposal of food waste in paper bags for decentralized drying before collection result in a larger net avoidence of global warming, eutrophication and acidification. However, both these systems not have been taken into use in large scale systems yet and further investigations are needed in order to confirm the outcomes from the comparison. Ranking of scenarios differ largely if considering only emissions in the foreground system, indicating the importance of taking also downstream emissions into consideration when comparing different collection systems. The hot spot identification shows that losses of organic matter in mechanical pretreatment as well as tank connected food waste disposal systems and energy in drying and vacuum systems reply to the largest impact on the results in each system respectively.     

Proximate composition of household waste and applicability of waste management technologies by source separation in Hanoi,Vietnam

The organic fraction of municipal solid wastes in Southeast Asia, which has a high moisture content, accounts for a large proportion of total waste. Local governments need to pay adequate attention to the composition of wastes to determine alternative waste management technologies. This study proposed the use of a triangle diagram to describe changes in proximate composition and rates of successful source separation of municipal solid waste and to identify technical challenges about alternative waste management technologies such as incineration, composting, and refuse-derived fuel production based on physical and proximate composition analysis of household waste sampled in Hanoi, Vietnam, as a case study. The analysis indicated the effectiveness of different types of source separation as well as different levels of successful achievement of source separation as an adjustment mechanism for the proximate composition of waste. Proper categorization of wastes for source separation is necessary for the appropriate use of alternative waste management technologies. The results showed that, at a source separation rate of just greater than 0.52 in a three-way separation scheme, the waste separated as combustible waste would be suitable for incineration with energy recovery. Based on well-designed schemes of source separation, alternative waste management technologies can be applied.     

Evaluation of environmental impacts from municipal solid waste management in the municipality of Aarhus, Denmark (EASEWASTE).

A new computer based life cycle assessment model (EASEWASTE) was used to evaluate a municipal solid waste system with the purpose of identifying environmental benefits and disadvantages by anaerobic digestion of source-separated household waste and incineration. The most important processes that were included in the study are optical sorting and pre-treatment, anaerobic digestion with heat and power recovery, incineration with heat and power recovery, use of digested biomass on arable soils and finally, an estimated surplus consumption of plastic in order to achieve a higher quality and quantity of organic waste to the biogas plant. Results showed that there were no significant differences in most of the assessed environmental impacts for the two scenarios. However, the use of digested biomass may cause a potential toxicity impact on human health due to the heavy metal content of the organic waste. A sensitivity analysis showed that the results are sensitive to the energy recovery efficiencies, to the extra plastic consumption for waste bags and to the content of heavy metals in the waste. A model such as EASEWASTE is very suitable for evaluating the overall environmental consequences of different waste management strategies and technologies, and can be used for most waste material fractions existing in household waste.     

Stress-strain response of plastic waste mixed soil

Recycling plastic waste from water bottles has become one of the major challenges worldwide. The present study provides an approach for the use plastic waste as reinforcement material in soil. The experimental results in the form of stress-strain-pore water pressure response are presented. Based on experimental test results, it is observed that the strength of soil is improved and compressibility reduced significantly with addition of a small percentage of plastic waste to the soil. The use of the improvement in strength and compressibility response due to inclusion of plastic waste can be advantageously used in bearing capacity improvement and settlement reduction in the design of shallow foundations.     

Waste plastics recycling process using coke ovens

The Japan Iron and Steel Federation (JISF), as its voluntary energy-saving action plan, proposed a 10% energy reduction by 2010 with 1990 as the basis. Further, it has suggested an additional 1.5% energy saving by the use of waste plastics as a metallurgical raw material. The amount of processing of waste plastics which corresponds to this amount of energy conversion is about 1 million t scale during 1 year. Conventional known methods for recycle-processing of waste plastics include, for example, the method of injection into a blast furnace to use waste plastics as an iron-ore reducing agent instead of coal. On the other hand, the coking process is considered to be suitable as a waste plastic recycling facility because the process involves coal carbonization in a high-temperature and reducing atmosphere. Carbonization tests with mixed waste plastics were conducted with laboratory equipment and in actual coke ovens. As a result, it was confirmed that the waste plastics recycling process using coke ovens is feasible. Therefore, a waste plastics recycling process using coke ovens was started as a chemical recycling technology at Nippon Steel.     

Model of technological alternatives of production of sodium chromate (VI) with the use of chromic wastes

This article presents a mathematical model which describes the sodium chromate (VI) production process with the use of chromic waste as a substitution of natural raw materials. This model is a function of selected process parameters common for all of the examined alternatives and based on equations of material balance. Optimization of the elaborated technological alternatives of the production process with use of recycling of chromic waste has been evaluated by determining the extreme value of the quality indicator WJ. This indicator defines the quantity of waste created in the process. Optimization results enabled the selection of the optimal technological solution from all of the alternatives possible for use in industrial practice. Negative values of the indicator prove that there is the possibility of introducing to the process a larger quantity of waste than the one obtained in the process and transported to the storage heaps.     

Comparing Waste-to-Energy technologies by applying energy system analysis

Even when policies of waste prevention, re-use and recycling are prioritised a fraction of waste will still be left which can be used for energy recovery. This article asks the question: How to utilise waste for energy in the best way seen from an energy system perspective? Eight different Waste-to-Energy technologies are compared with a focus on fuel efficiency, CO₂ reductions and costs. The comparison is carried out by conducting detailed energy system analyses of the present as well as a potential future Danish energy system with a large share of combined heat and power as well as wind power. The study shows potential of using waste for the production of transport fuels. Biogas and thermal gasification technologies are hence interesting alternatives to waste incineration and it is recommended to support the use of biogas based on manure and organic waste. It is also recommended to support research into gasification of waste without the addition of coal and biomass. Together the two solutions may contribute to alternate use of one third of the waste which is currently incinerated. The remaining fractions should still be incinerated with priority to combined heat and power plants with high electric efficiency.     

固体废物属性鉴别有关问题的思考

固体废物属性鉴别在进口废物管理方面具有重要作用,是口岸加强进口废物监管的重要技术支持依据。在进口物品固体废物属性鉴别中,各鉴别机构可能会遇到很多难以把握的问题。对固体废物属性鉴别关键问题进行思考,包括首要解决的问题、标准或规范的使用、鉴别的三个“键节点;过程产物的判断、特性分析、二次再生资源加工产物的判断等6个方面。     

Household waste disposal in Mekelle city, Northern Ethiopia

In many cities of developing countries, such as Mekelle (Ethiopia), waste management is poor and solid wastes are dumped along roadsides and into open areas, endangering health and attracting vermin. The effects of demographic factors, economic and social status, waste and environmental attributes on household solid waste disposal are investigated using data from household survey. Household level data are then analyzed using multinomial logit estimation to determine the factors that affect household waste disposal decision making. Results show that demographic features such as age, education and household size have an insignificant impact over the choice of alternative waste disposal means, whereas the supply of waste facilities significantly affects waste disposal choice. Inadequate supply of waste containers and longer distance to these containers increase the probability of waste dumping in open areas and roadsides relative to the use of communal containers. Higher household income decreases the probability of using open areas and roadsides as waste destinations relative to communal containers. Measures to make the process of waste disposal less costly and ensuring well functioning institutional waste management would improve proper waste disposal.     

Use of recycled plastic in concrete: a review

Numerous waste materials are generated from manufacturing processes, service industries and municipal solid wastes. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. Solid waste management is one of the major environmental concerns in the world. With the scarcity of space for landfilling and due to its ever increasing cost, waste utilization has become an attractive alternative to disposal. Research is being carried out on the utilization of waste products in concrete. Such waste products include discarded tires, plastic, glass, steel, burnt foundry sand, and coal combustion by-products (CCBs). Each of these waste products has provided a specific effect on the properties of fresh and hardened concrete. The use of waste products in concrete not only makes it economical, but also helps in reducing disposal problems. Reuse of bulky wastes is considered the best environmental alternative for solving the problem of disposal. One such waste is plastic, which could be used in various applications. However, efforts have also been made to explore its use in concrete/asphalt concrete. The development of new construction materials using recycled plastics is important to both the construction and the plastic recycling industries. This paper presents a detailed review about waste and recycled plastics, waste management options, and research published on the effect of recycled plastic on the fresh and hardened properties of concrete. The effect of recycled and waste plastic on bulk density, air content, workability, compressive strength, splitting tensile strength, modulus of elasticity, impact resistance, permeability, and abrasion resistance is discussed in this paper.     

Impact of food waste disposers on the generation rate and characteristics of municipal solid waste

Field surveys were carried out to ascertain the reduction in the generation rate of municipal solid waste as a result of the use of food waste disposers (FWDs). The generation rate and characteristics of garbage and of the food waste ground by FWDs in households were investigated, and the effect of FWDs was discussed. In a medium-sized village, the amount of garbage collected per collection decreased from 251.2 kg to 114.7 kg as a result of FWD use. The unit loading of ground food waste was estimated to be 111 g/cap·day. In a small village, the amount of garbage collected weekly decreased from 175 kg to 112 kg. The average unit loading of ground food waste was measured and found to be 126 g/cap·day. The reduction rate of garbage varied from 25% to 39% monthly and the average reduction rate was 31% throughout the surveying period. Dramatic variations in the characteristics of the collected garbage were recognized: the ratio of food waste on a dry basis declined by more than half, the moisture content decreased to half or less, the combustible matter content increased approximately 1.7 times or more, and the lower heating value increased approximately 2.0 times or more compared to the case without FWD use.     

Types of packaging waste from secondary sources (supermarkets)--the situation in the UK

Packaging waste is a contributing factor to the large quantity of waste that is sent to landfill in the UK. This research focuses on waste from the secondary packaging sector in the UK. In particular, supermarkets were investigated as they supply a large section of consumers with their grocery and other requirements and generate high quantities of packaging waste due to the high turnover within the store. In general, supermarkets use either metal cages or wooden pallets to transport products from depot to store. Investigation shows that packaging waste produced when using the wooden pallets is greater than for metal cages but the use of wooden pallets allows for greater versatility when in the store. The type of transit packaging used depends on what the products are initially packaged in and how the supermarket supply chain works. All cardboard and high-grade plastic is recycled but, depending on the facilities at the stores, the low-grade plastic can be recycled as well. This paper details types of packaging used within the supermarket secondary packaging sector and how waste can be reduced. To reduce the amount of packaging waste produced by the supermarkets, the products will have to be wrapped differently by the producers so that less packaging is needed in transit.     

Resolving public conflict in site selection process-a risk communication approach

In Japan, conflicts regarding the siting of waste disposal facilities occur frequently. In particular, siting of incinerators and landfills has become increasingly difficult because the public is highly concerned about the dioxin issues. Inefficient siting of waste disposal facilities causes several social problems, such as the shortage of waste treatment and disposal facilities, the rising of waste management costs and an increase in the consumption of resources. While dealing with a similar situation, the Chemical Society of Japan adopted a risk communication technique successfully. Hence, the pragmatic use of a risk communication technique is proposed to avoid conflicts and for a smooth information exchange to seek cooperation in waste management. In order to achieve this, a study was conducted to resolve conflicts between residents and the municipality for the selection of site for a solid waste treatment and disposal facility. This study aims to discuss the subject of risk communication for the waste disposal system in Japan. This study is performed through personal interviews and a questionnaire covering opposing parties in the town. As a result of the survey, a risk communication approach for a waste treatment and disposal system is presented in the paper addressing issues such as building of social trust, pragmatic use of the communication process, installation of credible information sources, and environmental education and awareness.     

Environmental assessment of solid waste systems and technologies: EASEWASTE.

A new model has been developed for evaluating the overall resource consumption and environmental impacts of municipal solid waste management systems by the use of life cycle assessment. The model is named EASEWASTE (Environmental Assessment of Solid Waste Systems and Technologies) and is able to compare different waste management strategies, waste treatment methods and waste process technologies. The potential environmental impacts can be traced back to the most important processes and waste fractions that contribute to the relevant impacts. A model like EASEWASTE can be used by waste planners to optimize current waste management systems with respect to environmental achievements and by authorities to set guidelines and regulations and to evaluate different strategies for handling of waste. The waste hierarchy has for decades been governing waste management but the ranking of handling approaches may not always be the most environmentally friendly. The EASEWASTE model can identify the most environmentally sustainable solution, which may differ among waste materials and regions and can add valuable information about environmental achievements from each process in a solid waste management system.     

Quantifying the waste reduction potential of using prefabrication in building construction in Hong Kong

As Hong Kong is a compact city with limited available land and high land prices, the construction of high-rise buildings is prevalent. The construction industry produces a significant amount of building waste. In 2005, about 21.5 million tonnes of construction waste were generated, of which 11% was disposed of in landfills and 89% in public filling areas. At the present rate, Hong Kong will run out of both public filling areas and landfill space within the next decade. The government is taking action to tackle the problem, such as by introducing a construction waste landfill charge, and promoting prefabrication to reduce on-site waste generation. This paper reports an ongoing study on the use of prefabrication in buildings and its impact on waste reduction in Hong Kong. A questionnaire survey was administered to experienced professionals, and case studies of recently completed building projects were conducted. The results revealed that construction waste reduction is one of the major benefits when using prefabrication compared with conventional construction. The average wastage reduction level was about 52%. This implies that a wider use of prefabrication could considerably reduce construction waste generation in Hong Kong and alleviate the burdens associated with its management.     

Planning for integrated solid waste management at the industrial park level: a case of Tianjin, China

Industrial parks play a significant role in the production and use of goods and services. The proper management of solid waste is a major challenge for industrial parks due to the large quantity of wastes and the variability of waste characteristics from these types of developments. Therefore, integrated solid waste management has become very crucial to the industrial park managers. Such an approach requires industrial park managers to assess the overall use of resources, and to seek waste reduction, reuse and recycling opportunities both at the individual company level and among different tenant companies. The adoption of this method can bring both economic and environmental benefits. This paper introduces the planning efforts of a real case in China. It first presents the basic information on Tianjin Economic Development Area (TEDA), and then introduces its current practices on solid waste management. The main focus of this paper is to describe how to plan an integrated solid waste management system at TEDA. Benefits and challenges are all identified and analyzed. The experiences and methods from this case study should be applied in other industrial parks so as to improve the overall eco-efficiency of the whole industrial park.     

Review and prospect of emerging contaminants in waste – Key issues and challenges linked to their presence in waste treatment schemes: General aspects and focus on nanoparticles

The presence in waste of emerging pollutants (EPs), whose behaviours and effects are not well understood, may present unexpected health and environmental risks and risks for the treatment processes themselves. EP may include substances that are newly detected in the environment, substances already identified as risky and whose use in items is prohibited (but which may be present in old or imported product waste) or substances already known but whose recent use in products can cause problems during their future treatment as waste. Several scientific studies have been conducted to assess the presence of EP in waste, but they are mostly dedicated to a single category of substance or one particular waste treatment. In the absence of a comprehensive review focused on the impact of the presence of EP on waste treatment schemes, the authors present a review of the key issues associated with the treatment of waste containing emerging pollutants. This review presents the typologies of emerging pollutants that are potentially present in waste along with the major challenges for each treatment scheme (recycling, composting, digestion, incineration, landfilling and wastewater treatment). All conventional treatment processes are affected by these new pollutants, and they were almost never originally designed to consider these substances. In addition to these general aspects, a comprehensive review of available data, projects and future R&D needs related to the impact of nanoparticles on waste treatment is presented as a case study.     

Raw material potential of recyclable materials for fiber composites: a review study

The aim of this study is to investigate waste streams as a source of recyclable raw material for fiber composite production. Globally, vast volumes of waste are produced daily that are not recycled effectively. In this work, three different raw material sources are examined; industrial, construction and municipal solid waste streams. All three sources produce wastes that are currently underutilized. Usage areas for the waste material include use as a reinforcing fiber, as part of the plastic matrix or as a filler. The industrial sector produces more homogenous waste, while waste from municipalities is mixed. Irregular material flow, the varying condition of the waste and different pretreatments used pose difficulties for recycling. Furthermore, some materials are industry-specific and may be produced in only certain areas. Despite these difficulties, huge amount of potentially useful exploitable waste is available and using different waste streams as a part of wood-plastic composite production can reduce waste volumes disposed to landfill.     

A review of municipal solid waste composition in the United Kingdom

The move from landfill-based to resource-based waste management systems requires a greater knowledge of the composition of municipal solid waste. This paper draws together the findings of municipal solid waste (MSW) compositional surveys undertaken in the United Kingdom. The results from recent surveys show a good agreement over the composition of household-collected waste, but less agreement over civic amenity site waste composition. There is insufficient data to allow comparisons of the commercial waste element of municipal waste or of the other components, and further work is necessary to produce more reliable estimates of the composition of these streams. The use of questionnaire surveys and analysis of the results suggests that the size and age profile of a household influence the generation of household-collected waste. Some research suggests that the waste container provided by the local authority and the socio-economic classification of a household also influence household-collected waste generation, but other studies failed to find this link. Further research is required to investigate this by surveying all of the waste disposal routes available to specific households.