Orange peel as an adsorbent in the removal of acid violet 17 (acid dye) from aqueous solutions

The effectiveness of orange peel in adsorbing Acid violet 17 from aqueous solutions has been studied as a function of agitation time, adsorbent dosage, initial dye concentration and pH. The adsorption follows both Langmuir and Freundlich isotherms. The adsorption capacity Q0 was 19.88 mg/g at initial pH 6.3. The equilibrium time was found to be 80 min for 10, 20, 30 and 40 mg/L, dye concentration respectively. A maximum removal of 87% was obtained at pH 2.0 for an adsorbent dose of 600 mg/50 ml of 10 mg/L dye concentration. Adsorption increases with increase in pH. Maximum desorption of 60% was achieved in water medium at pH 10.0.     

聚丙烯酸钠-硅溶胶的合成及其对阳离子金黄染料的吸附

通过简单的水溶液聚合法成功合成了聚丙烯酸钠-硅溶胶复合吸附剂,并对其进行了SEM和热重分析,研究了吸附条件对该吸附剂对阳离子金黄染料吸附效果的影响。实验结果表明,当硅溶胶质量分数为20%、初始染料质量浓度为60 mg/L、初始溶液pH为7、反应温度为298 K时,聚丙烯酸钠-硅溶胶复合吸附剂对阳离子金黄染料的吸附量为64.64 mg/g。由二级吸附动力学模型获得的活化能(Ea=2.617 kJ/mol)表明,聚丙烯酸钠-硅溶胶复合材料对阳离子金黄的吸附属于物理吸附,低温有利于吸附。     

Experimental and Modeling Studies for the Removal of Crystal Violet Dye from Aqueous Solutions using Eco-friendly <Emphasis Type="Italic">Gracilaria corticata</Emphasis> Seaweed Activated Carbon/Zn/Alginate Polymeric Composite Beads

This research article describes, an eco-friendly activated carbon prepared from the Gracilaria corticata seaweeds which was employed for the preparation of biodegradable polymeric beads for the efficient removal of crystal violet dye in an aqueous solution. The presence of chemical functional groups in the adsorbent material was detected using FTIR spectroscopy. The morphology and physical phases of the adsorbent materials were analyzed using SEM and XRD studies respectively. Batch mode dye adsorption behavior of the activated carbon/Zn/alginate polymeric beads was investigated as a function of dosage, solution pH, contact time, initial dye concentration and temperature. Maximum dye removal was observed at a pH of 5.0, 1 g of adsorbent dosage with 60 mg/L dye concentration, 50 min of contact time and at 30 °C. The equilibrium modeling studies were analyzed with Freundlich and Langmuir adsorption isotherms and the adsorption dynamics was predicted with Lagergren’s pseudo-first order, pseudo-second order equations and intra particle diffusion models. The process of dye removal followed a pseudo second-order kinetics rather than pseudo first order. The thermodynamic parameters like standard Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined and the results imply that the adsorption process was spontaneous, endothermic and increases the randomness between the adsorbent and adsorbate. The results from the experimental and correlation data reveal that the Gracilaria corticata activated carbon/Zn/alginate polymeric beads have proved to be an excellent adsorbent material for the removal of CV dye.     

染料生物吸附影响因素与解吸条件研究

用筛选出的一株丝状真菌(GX2)对活性、酸性、碱性和直接染料进行吸附及解吸的试验结果表明，该菌株对活性、酸性和直接染料有较高的吸附率，但碱性染料难被吸附；在多种有机溶剂中，丙酮是较好的解吸剂，碱性介质有利于染料的解吸；对菌体进行破碎及在解吸过程中加以搅拌有利于解吸过程的进行。     

凹凸棒土/苯胺-邻氨基酚复合吸附剂的制备及其对Cr(Ⅵ)的吸附性能

采用原位聚合法制备了凹凸棒土/苯胺-邻氨基酚（ATP/PANOAP）复合吸附剂,对其进行了SEM和FTIR表征,并通过吸附实验考察了ATP/PANOAP对水中Cr（Ⅵ）的吸附性能。实验结果表明,ATP/PANOAP对水中Cr（Ⅵ）具有良好的去除效果,在Cr（Ⅵ）初始质量浓度为50 mg/L、溶液pH为6、吸附剂加入量为0.375 g/L、温度为298 K的条件下,Cr（Ⅵ）去除率达93.39%。ATP/PANOAP对Cr（Ⅵ）的吸附动力学过程符合准二级动力学模型,吸附热力学过程符合Langmuir单层吸附模型,该吸附过程以化学吸附为主,且为自发进行的吸热反应。     

离子交换树脂D001对罗丹明B的吸附特性

采用强酸性阳离子交换树脂D001作为吸附剂吸附脱除水溶液中的罗丹明B(Rh B)。SEM和FTIR表征结果显示:D001树脂表面存在孔隙,可增加树脂的比表面积;树脂表面的磺酸基团可通过与阳离子染料Rh B络合而将其吸附。实验结果表明:Langmuir等温吸附模型能更好地描述树脂对Rh B的吸附规律,升高温度有利于树脂吸附Rh B;吸附过程符合Lagergren准一级动力学方程,初始Rh B质量浓度为20 mg/L时吸附活化能为7.06 k J/mol;树脂对Rh B的吸附是一个自发的、吸热的、熵推动的过程;颗粒扩散为吸附过程的控制步骤;树脂具有良好的重复使用性能。     

酸化碱渣对氨氮的吸附和解吸性能

研究了氨氮质量浓度、体系温度、时间、酸化碱渣溶液的pH等对酸化碱渣吸附氨氮性能的影响,比较了作为解吸剂的蒸馏水和NaCl溶液对氨氮的解吸效果。在选定的实验条件下,酸化碱渣对氨氮的最大吸附量可达13．9mg／g。氨氮吸附量随其质量浓度的增加而增大、随体系温度的升高而降低,酸化碱渣溶液的pH对吸附性能的影响可以忽略。酸化碱渣表面吸附作用力主要为偶极间力和氢键力,吸附过程可用一级动力学方程模拟。NaCl溶液对氨氮的解吸效果好于蒸馏水,最大解吸率为25．7％。     

Activated carbon from Ceiba pentandra hulls, an agricultural waste, as an adsorbent in the removal of lead and zinc from aqueous solutions

The ability of low-cost activated carbon prepared from Ceiba pentandra hulls, an agricultural waste material, for the removal of lead and zinc from aqueous solutions has been investigated. In the batch tests experimental parameters were studied, including solution pH, contact time, adsorbent dose and initial metal ions concentration. The adsorbent exhibited good sorption potential at pH 6.0. Maximum removal of lead (99.5%) and of zinc (99.1%) with 10 g/l of sorbent was observed at 50 mg/L sorbate concentration. Removals of about 60-70% occurred in 10 min, and equilibrium was attained at around 50 min for both metals. The functional groups (CO, SO,-OH) present on the carbon surface were responsible for the adsorption of metal ions. The adsorption parameters were analysed using both the Freundlich and Langmuir models. The data are better fitted by the Freundlich isotherm as compared to Langmuir model, and the adsorption capacities for lead and zinc were 25.5 and 24.1 mg/g, respectively. Kinetics of adsorption obeyed a second order rate equation and the rate constant was found to be 2.71 x 10(-2) and 2.08 x 10(-2) g/mg/min for lead and zinc, respectively. The desorption studies were carried out using dilute HCl, and the effect of HCl concentration on desorption was studied. Maximum desorptions of 85% for lead and 78% for zinc were attained with 0.15 M HCl.     

改性核桃壳对Cr(Ⅵ)的吸附

采用甲醛-硫酸改性法制备改性核桃壳吸附剂,利用静态吸附法研究了改性核桃壳对模拟废水中低浓度Cr(Ⅵ)的吸附性能,并采用SEM和FTIR技术对改性前后的核桃壳进行表征。表征结果显示,改性后的核桃壳表面更粗糙,孔隙轮廓更清晰,更有利于对Cr(Ⅵ)的吸附。实验结果表明:在初始Cr(Ⅵ)质量浓度为20 mg/L、初始废水p H为1、吸附温度为30℃、吸附时间为100 min、改性核桃壳加入量为24 g/L的条件下,改性核桃壳对Cr(Ⅵ)的去除率为98.4%,高于在相同条件下未改性核桃壳对Cr(Ⅵ)的去除率(93.1%);改性核桃壳对Cr(Ⅵ)的吸附更符合Freundlich等温吸附方程,对Cr(Ⅵ)的吸附行为满足拟二级动力学方程。     

水性油墨废水絮凝污泥制备吸附剂及阳离子染料的吸附

以水性油墨废水絮凝污泥为原料、采用一步炭化活化法制备了吸附剂,并将其用于阳离子蓝X-GRRL溶液(300 mg/L)的吸附处理。考察了吸附剂投加量、吸附时间、吸附温度和吸附pH对吸附效果的影响,并对吸附动力学进行了探讨。结果表明:所制得吸附剂的总孔体积为0.5 cm~3/g,平均孔径为7.12 nm;在吸附剂投加量0.6g/L、吸附时间420 min、吸附温度25℃、吸附pH 5.4的条件下,吸附量高达486.21 mg/g,脱色率达97.24%;该吸附剂对于阳离子蓝X-GRRL的吸附过程可用准二级动力学模型和颗粒内扩散效应模型很好地描述。     

球形纤维素吸附剂对Cr3+吸附和解吸的研究

用静态法和动态法研究了球形纤维素吸附剂对水中 Cr3+的吸附和解吸 ,包括静态等温吸附以及各种因素对吸附的影响等 ,并探讨了吸附机理。 Cr3+的吸附容量为 2 8mg/ g,采用浓度为 1.2 mol/ L 的 HCl溶液作解吸液回收 Cr3+的综合效果较好。静态法和动态法的吸附率均达 90 %左右 ,解吸率均达 85 %以上 ,且静态法的吸附率和解吸率分别略高于动态法的吸附率和解吸率 ,但动态法耗时短 ,更符合工业化要求。     

Synthesis of Gum Acacia Capped Polyaniline-Based Nanocomposite Hydrogel for the Removal of Methylene Blue Dye

In this research work, a novel gum acacia capped polyaniline-based nanocomposite hydrogel (GPA NCHs) was developed and evaluated for the adsorptive removal of cationic methylene blue dye (MB) from aqueous solutions. Firstly, Gum acacia (GA) capped Polyaniline (PANI) dispersion was synthesized by using dispersion polymerization. Then, a water-swellable hydrogel network consisting of GA-PANI and acrylamide (AM) was obtained by using N,N′ -methylene-bisacrylamide (MBA) as a cross-linker, and ammonium persulphate/N,N,N′,N′-tetramethylethylenediamine (APS/TMEDA) as an initiating system. The developed materials were characterized by UV–visible, FTIR, XRD, SEM–EDX and TEM techniques. The microscopy studies revealed that GA-PANI nanoparticles have a granular morphological surface with an average size of?~?40–100 nm. Removal of MB dye from aqueous system was performed by adsorption studies in batch equilibrium mode with different dosage of GA-PANI, MB concentration, pH and temperatures. The adsorption data revealed that the absorption capacity of GPA NCHs highly depends on the dosage of GA-PANI, pH and concentration of the MB dye. The maximum percentage of MB removal onto GPA 1.0 NCHs was found to be 89% at pH 10 with a dye concentration of 10 mg L^?1. The equilibrium adsorption data were also analyzed by different models to understand the adsorption process. The results revealed that the adsorption process followed the pseudo-second-order kinetics and it fit well in Langmuir and Freundlich adsorption isotherms with a maximum adsorption capacity of 35.41 mg g^?1. These studies demonstrate that the GPA NCHs could be a promising adsorbent material for the removal of MB dye from contaminated aqueous systems.

     

Novel Fabrication of PAA/PVA/Yeast Superabsorbent with Interpenetrating Polymer Network for pH-Dependent Selective Adsorption of Dyes

Traditional superabsorbent polymers have wide application potential as an adsorbent, but the poor physical and mechanical properties limit their further applications. To tentatively overcome this dilemma, a novel poly(acrylic acid)/poly(vinyl alcohol)/yeast superabsorbent polymers (PAA/PVA/yeast SAPs) with interpenetrating polymer networks (IPNs) were fabricated herein via solution polymerization. The mechanical stability tests showed that the resulting products could desirably resist the destruction of shear flow (<5000 rpm) and load pressure (<3 kg). The effects of yeast content, pH, contact time, initial dye concentration and temperature were systematically studied to evaluate their adsorption properties. Consecutive five cycles of adsorption–desorption indicated that their easy regeneration and reusability. More importantly, the PVA/PAA/yeast SAPs displayed brilliant pH-dependent selective adsorption for dyes in dye mixtures. It is believed hereby that the PAA/PVA/yeast SAPs can be expected to be economically and technically feasible for the scalable treatment of dyes wastewater.     

核桃壳吸附剂对水中Pb2+的吸附

采用自制核桃壳吸附剂，利用静态吸附法，处理模拟含Pb²⁺废水。实验结果表明：当初始Pb²⁺的质量浓度20.00 mg/L、初始废水pH=5.5、吸附剂加入量12 g/L、吸附剂粒径1.60~2.50 mm、吸附时间120 min时，核桃壳吸附剂对Pb²⁺的去除率为91.7%；吸附剂对Pb²⁺的吸附行为满足拟二级吸附动力学方程，吸附等温线满足Langmuir等温方程，饱和吸附量达到3.903 mg/g；吸附饱和的吸附剂可用浓度 0.1 mol/L的硝酸解吸，经解吸后的吸附剂可重复利用3次。     

Effective Removing of Remazol Black B by the Polyacrylamide Cryogels Modified with Polyethyleneimine

In this study, modified polyacrylamide (PAAm) cryogels with high dye holding capacity were synthesized with an easily and cheaply process and adsorption of Remazol Black B (RBB) with the synthesized materials was investigated. Firstly, PAAm cryogels were synthesized with free radical cryo-copolymerization method and they were modified with Hofmann reaction to form amine groups in the structure of the cyrogels. Then, to increase the removal efficiency of cryogels, polyethylenimine (PEI) molecules were crosslinked onto the cryogels via NH₂ groups present in the PAAm gels modified by the Hofmann reaction. The original and modified cryogels were characterized with fourier transformed infrared spectroscopy, ¹³C nuclear magnetic resonance spectroscopy, scanning electron microscopy and thermogravimetric analysis. The point of zero charge (pH_pzc) of the modified cryogels was found to be 7.13 and RBB removing capabilities of PEI-modified PAAm cryogels were investigated at pH between 2 and 7. In addition, the adsorption treatments were performed at different process time, incubation temperature, initial dye concentration and adsorbent amount to find maximum removal capacity of the adsorbent. The modified cryogels adsorbed maximum amount of RBB at pH 2 and the sorption process reached equilibrium in 6 h. It was observed that the adsorption efficiency did not change much with the increase in temperature. The maximum RBB removal capacity of the modified cyrogels was determined to be 201 mg/g when the initial RBB concentration was 200 mg/L, treatment time was 6 h at pH 2. Moreover, the adsorption of RBB dye with the modified cryogels takes place with a second order kinetic and RBB dye adsorption data showed compliance with the Langmuir isotherm. The findings of the study expose that the obtained PEI-modified PAAm cryogels are a hopeful material for RBB removal in aqueous environment.

     

Removal of fluoride from water using aluminum-modified activated carbon prepared from khat (Catha edulis) stems

This study investigated the fluoride removal efficiency and adsorption of a low-cost adsorbent prepared using aluminum-modified activated carbon from khat (Catha edulis) in a batch-mode reactor. The operating factors, including pH, adsorbent dose, and fluoride initial concentration, were optimized using the Box Behnken design of response surface methodology. The correlation coefficient (R²) for the removal of fluoride was found to be 0.93, showing the validity of the developed quadratic model. The results showed that, under optimized conditions of an adsorbent dose of 2.47 g/L, an initial fluoride concentration of 2.1 mg/L, an initial pH 6.08, and 60 min, 90% fluoride reduction was achieved. Meanwhile, the adsorption isotherm and kinetics followed the Langmuir adsorption model and the Pseudo second model, respectively, with a monolayer adsorption capacity of 0.3065 mg/g. On the other hand, Fourier transform infrared spectroscopy and scanning electron microscopy analyses revealed the formation of major peaks of components such as hydroxyl and carboxylic acids. The same optimum treatment conditions (adsorbent dose of 2.47 g/L, initial pH 6.08, and treatment time of 60 min) managed to remove low initial fluoride concentrations of 3.67 and 4.33 mg/L from real groundwater by 72.84% and 70.37%, respectively. The modified adsorbent prepared in this study successfully treat the low fluoride concentration to a level recommended by WHO for drinking water.     

NDA-66树脂对邻苯二甲酸的吸附及脱附性能

研究了NDA-66新型超高交联树脂对邻苯二甲酸的吸附及脱附性能。实验结果表明：静态吸附过程中，在初始邻苯二甲酸质量浓度1 000 mg/L、溶液pH=2.0、吸附时间600 min的条件下，吸附量可达190 mg/g；动态吸附过程中，处理11吸附床层体积倍数（BV）的邻苯二甲酸溶液，当溶液流量为1.5 BV/h时，吸附率可达100%；动态脱附过程中，在w（NaOH）= 6%、脱附温度328 K的最佳脱附条件下，脱附率可达99%以上。     

Assessment of Potential Capability of Water Bamboo Leaves on the Adsorption Removal Efficiency of Cationic Dye from Aqueous Solutions

Removal of toxic pollutants from water and wastewater is becoming an important process with the increase of industrial activities. The present study focused on assessing the suitability and efficiency of water bamboo leaves (WBL) for the removal of cationic dye from aqueous solutions. The effect of different variables in the batch method including solution pH (2–12), initial dye concentration (50–250 mg L^?1), adsorbent dose (0.05–0.30 g), contact time (5–180 min) and temperature (283–333 K) on the dye removal was investigated. The adsorption kinetics was discussed in view of four kinetics models. The results showed that the pseudo-second-order kinetics model described dye adsorption on WBL very well. The experimental equilibrium data were also tested by four isotherm models. It was found that adsorption of dye on WBL fitted well with the Langmuir isotherm model, implying the binding energy on the whole surface of the adsorbent was uniform and the dye molecules onto the surface of the adsorbent were monolayer coverage. Calculation of various thermodynamic parameters of the adsorption process indicated feasibility and exothermic nature of dye adsorption.     

The Removal of Acid Violet 90 from Aqueous Solutions Using PANI and PANI/Clinoptilolite Composites: Isotherm and Kinetics

Polyaniline (PANI) and polyaniline/Gördes-clinoptilolite (PANI/GC) composite materials were synthesized by the chemical oxidative polymerization technique and used in the adsorption of Acid Violet 90 metal-complex dye (AV 90). The samples were characterized by X-ray diffractions, nitrogen adsorption–desorption isotherms, scanning electron microscopes and Fourier transform infrared. The effect of initial pH (2–8), sorbent dosage (0.5–4.0 g/L) and initial dye concentrations (50–400 mg/L) on adsorption onto PANI and PANI/GC were examined in a batch system. Langmuir, Freundlich and Temkin isotherm models were used to investigate the adsorption mechanism of AV 90 on PANI and PANI/GC. Langmuir isotherm model for PANI/GC and Freundlich isotherm model for PANI were fitted well with the experimental data. The highest dye uptake capacities were obtained with Langmuir isotherm model as 153.85 mg/g and 72.46 mg/g for PANI and PANI/GC, respectively. In order to determine the adsorption kinetics, pseudo first-order and second-order kinetic models were studied. As a result, the adsorption of AV 90 dye on PANI and PANI/GC was better identified with Pseudo second-order kinetic model than the first one.     

Investigation of the Thermosensitive Nanosphere Polymer in Removing Organophosphorus Pesticides from Water and Its Isotherm Study (Case Study: Diazinon)

In this research, a novel thermosensitive nanosphere polymer (TNP) was synthesized by copolymerization of N-isopropylacrylamide with 3-allyloxy-1,2-propanediol for the removal of diazinon from water. The characterization of the synthesized adsorbent has been performed by Fourier transform infrared spectrometer, scanning electron microscopy and elemental analysis. Batch adsorption method was performed to investigate the influences of various parameters like pH, temperature and contact time on the adsorption of diazinon. The equilibrium adsorption data of diazinon by TNP was studied by Langmuir, Freundlich, Temkin and Redlich–Peterson model. According to equilibrium adsorption results, the Langmuir, Freundlich and Temkin constants were evaluated to be 0.912 (L/mg), 7.916 (mg/g) (L/mg)^1/n and 2.494 respectively at pH 7 and room temperature. Based on Redlich–Peterson model analysis, the equilibrium data for the adsorption of diazinon was conformed well to the Langmuir isotherm model. This method was successfully applied for removal of diazinon from environmental samples. Moreover, in reusing of TNP, the sorption capacity was maintained without any significant change after 10 cycles of sorption–desorption process.