Air pollutant concentrations near three Texas roadways, part II: Chemical characterization and transformation of pollutants

Spatial gradients of vehicular emitted air pollutants were measured in the vicinity of three roadways in the Austin, Texas area: (1) State Highway 71 (SH-71), a heavily traveled arterial highway dominated by passenger vehicles; (2) Interstate 35 (I-35), a limited access highway north of Austin in Georgetown; and (3) Farm to Market Road 973 (FM-973), a heavily traveled surface roadway with significant truck traffic. A mobile monitoring platform was used to characterize the gradients of CO and NO_x concentrations with increased distance from each roadway, while concentrations of carbonyls in the gas-phase and fine particulate matter mass and composition were measured at stationary sites upwind and at one (I-35 and FM-973) or two (SH-71) downwind sites. Regardless of roadway type or wind direction, concentrations of carbon monoxide (CO), nitric oxide (NO), and oxides of nitrogen (NO_x) returned to background levels within a few hundred meters of the roadway. Under perpendicular wind conditions, CO, NO and NO_x concentrations decreased exponentially with increasing distance perpendicular to the roadways. The decay rate for NO was more than a factor of two greater than for CO, and it comprised a larger fraction of NO_x closer to the roadways than further downwind suggesting the potential significance of near roadway chemical processing as well as atmospheric dilution. Concentrations of most carbonyl species decreased with distance downwind of SH-71. However, concentrations of acetaldehyde and acrolein increased farther downwind of SH-71, suggesting chemical generation from the oxidation of primary vehicular emissions. The behavior of particle-bound organic species was complex and further investigation of the size-segregated chemical composition of particulate matter (PM) at increasing downwind distances from roadways is warranted. Fine particulate matter (PM_2.5) mass concentrations, polycyclic aromatic hydrocarbons (PAHs), hopanes, and elemental carbon (EC) concentrations generally exhibited concentrations that decreased with distance downwind of SH-71. Concentrations of organic carbon (OC) increased from upwind concentrations immediately downwind of SH-71 and continued to increase further downwind from the roadway. This behavior may have primarily resulted from condensation of semi-volatile organic species emitted from vehicle sources with transport downwind of the roadway.     

Evaluation of the CAR-FMI model against measurements near a major road

A field measurement campaign was conducted near a major road in southern Finland from September 15 to October 30, 1995. The concentrations of NO, NO₂ and O₃ were measured simultaneously at three locations, at three heights (3.5, 6 and 10 m) on both sides of the road. Traffic densities and relevant meteorological parameters were also measured on-site. We have compared measured concentration data with the predictions of the road network dispersion model CAR-FMI, used in combination with a meteorological pre-processing model MPP-FMI. In comparison with corresponding results presented previously in the literature, the agreement of measured and predicted datasets was good, as measured using various statistical parameters. For all data (N=587), the index of agreement (IA) was 0.83, 0.82 and 0.89 for the measurements of NO_x, NO₂ and O₃, respectively. The IA is a statistical measure of the correlation of the predicted and measured time series of concentrations. However, the modelling system overpredicts NO_x concentrations with a fractional bias FB=+13%, and O₃ concentrations with FB=+8%, while for NO₂ concentrations FB=−2%. We also analyzed the difference between model predictions and measured data in terms of meteorological parameters. Model performance clearly deteriorated as the wind direction approached a direction parallel to the road, and for the lowest wind speeds. The range of variability concerning atmospheric stability, ambient temperature and the amount of solar radiation was modest during the measurement campaign. As expected, no clear dependencies of model performance were therefore detected in terms of these parameters. The experimental dataset is available for the evaluation of other roadside dispersion models.     

The influence of highway traffic on ambient nitrogen dioxide concentrations beyond the immediate vicinity of highways

The objective of these analyses was to determine whether highways significantly influence ambient concentrations of NO₂ at distances greater than 200 m. NO₂ was sampled for 14 consecutive days in May 2003 at 67 sites across Montréal, Canada. The association between logarithmic concentrations of NO₂ and land-use variables was assessed using multiple regressions. Locations less than 100 m from the nearest highways were excluded, leaving 61 data points. Then, locations less than 200 m were excluded, leaving 55 data points. Excluding sampling locations located less than 100 or 200 m from the nearest highway did not substantially change the regression parameters. NO₂ was still significantly associated with both the distance from nearest highway and the traffic count on the nearest highway. These findings indicate that the negative association found between distance from highways and NO₂ concentration in several land-use regression studies in Europe and North America was not generated solely by the high concentrations found in the immediate vicinity of highways.     

NOX Levels in the Caracas Valley

An analysis of air quality data from 1970-1975 in the Los Angeles (LA) Basin has been made with emphasis on factors relevant to high hourly NO₂ concentrations, (NO₂). Detailed analysis of CO and SO₂ air quality and the (NO _x )/(CO) and (CO)/(SO₂) ratios reveals that high (NO₂) result mainly from vehicular sources; contributions from stationary sources to these high (NO₂) of greater than 10% occur rarely. Meteorological conditions (very low early-morning inversion base height and low wind speed) favoring the formation of high (NO₂) restrict the impact of elevated point NO _x sources on the ground level (NO₂) during the early to mid-morning hours. The overnight leftover NO _x during high NO₂ days is shown to originate largely from local sources near the monitoring sites. A regression analysis using NO₂, NO _x and HC data from downtown LA shows that a 50% reduction in (NO _x ) reduces high (NO₂) by 40-45%; a 50% reduction in (HC) reduces high (NO₂) by 5-10%. The present analysis supports assumptions used in an earlier generalized rollback model that related NO _x emissions to high 1-h average (NO₂) observed at downtown LA.     

Analysis of air quality data near roadways using a dispersion model

We used a dispersion model to analyze measurements made during a field study conducted by the U.S. EPA in July–August 2006, to estimate the impact of traffic emissions on air quality at distances of tens of meters from an eight-lane highway located in Raleigh, NC. The air quality measurements consisted of long path optical measurements of NO at distances of 7 and 17 m from the edge of the highway. Sonic anemometers were used to measure wind speed and turbulent velocities at 6 and 20 m from the highway. Traffic flow rates were monitored using traffic surveillance cameras. The dispersion model [Venkatram, A., 2004. On estimating emissions through horizontal fluxes. Atmospheric Environment 38, 2439–2446] explained over 60% of the variance of the observed path averaged NO concentrations, and over 90% of the observed concentrations were within a factor of two of the model estimates.Sensitivity tests conducted with the model indicated that the traffic flow rate made the largest contribution to the variance of the observed NO concentrations. The meteorological variable that had the largest impact on the near road NO concentrations was the standard deviation of the vertical velocity fluctuations, σ_w. Wind speed had a relatively minor effect on concentrations. Furthermore, as long as the wind direction was within ±45° from the normal to the road, wind direction had little impact on near road concentrations. The measurements did not allow us to draw conclusions on the impact of traffic-induced turbulence on dispersion. The analysis of air quality and meteorological observations resulted in plausible estimates of on-road emission factors for NO.     

Evaluation of a Gaussian and a Lagrangian model against a roadside data set,with emphasis on low wind speed conditions

The evaluation of the high percentiles of concentration distributions is required by most national air quality guidelines, as well as the EU directives. However, it is problematic to compute such high percentiles in stable, low wind speed or calm conditions. This study utilizes the results of a previous measurement campaign near a major road at Elimäki in southern Finland in 1995, a campaign specifically designed for model evaluation purposes. In this study, numerical simulations were performed with a Gaussian finite line source dispersion model CAR-FMI and a Lagrangian dispersion model GRAL, and model predictions were compared with the field measurements. In comparison with corresponding results presented previously in the literature, the agreement of measured and predicted data sets was good for both models considered, as measured using various statistical parameters. For instance, considering all NO_x data (N=587), the so-called index of agreement values varied from 0.76 to 0.87 and from 0.81 to 1.00 for the CAR-FMI and GRAL models, respectively. The CAR-FMI model tends to slightly overestimate the NO_x concentrations (fractional bias FB=+14%), while the GRAL model has a tendency to underestimate NO_x concentrations (FB=−16%). The GRAL model provides special treatment to account for enhanced horizontal dispersion in low wind speed conditions; while such adjustments have not been included in the CAR-FMI model. This type of Lagrangian model therefore predicts lower concentrations, in conditions of low wind speeds and stable stratification, in comparison with a standard Lagrangian model. In low wind speed conditions the meandering of the flow can be quite significant, leading to enhanced horizontal dispersion. We also analyzed the difference between the model predictions and measured data in terms of the wind speed and direction. The performance of the CAR-FMI model deteriorated as the wind direction approached a direction parallel to the road, and for the lowest wind speeds. However, the performance of the GRAL model varied less with wind speed and direction; the model simulated better the cases of low wind speed and those with the wind nearly parallel to the road.     

Assessing Spatial Variability of Ambient Nitrogen Dioxide in Montréal,Canada, with a Land-Use Regression Model

Abstract

The purpose of this study was to derive a land-use regression model to estimate on a geographical basis ambient concentrations of nitrogen dioxide (NO₂) in Montréal, Quebec, Canada. These estimates of concentrations of NO₂ will be subsequently used to assess exposure in epidemiologic studies on the health effects of traffic-related air pollution. In May 2003, NO₂ was measured for 14 consecutive days at 67 sites across the city using Ogawa passive diffusion samplers. Concentrations ranged from 4.9 to 21.2 ppb (median 11.8 ppb). Linear regression analysis was used to assess the association between logarithmic concentrations of NO₂ and land-use variables derived using the ESRI Arc 8 geographic information system. In univariate analyses, NO₂ was negatively associated with the area of open space and positively associated with traffic count on nearest highway, the length of highways within any radius from 100 to 750 m, the length of major roads within 750 m, and population density within 2000 m. Industrial land-use and the length of minor roads showed no association with NO₂. In multiple regression analyses, distance from the nearest highway, traffic count on the nearest highway, length of highways and major roads within 100 m, and population density showed significant associations with NO₂; the best-fitting regression model had a R² of 0.54. These analyses confirm the value of land-use regression modeling to assign exposures in large-scale epidemiologic studies.     

The use of wind fields in a land use regression model to predict air pollution concentrations for health exposure studies

A methodology is developed to include wind flow effects in land use regression (LUR) models for predicting nitrogen dioxide (NO₂) concentrations for health exposure studies. NO₂ is widely used in health studies as an indicator of traffic-generated air pollution in urban areas. Incorporation of high-resolution interpolated observed wind direction from a network of 38 weather stations in a LUR model improved NO₂ concentration estimates in densely populated, high traffic and industrial/business areas in Toronto-Hamilton urban airshed (THUA) of Ontario, Canada. These small-area variations in air pollution concentrations that are probably more important for health exposure studies may not be detected by sparse continuous air pollution monitoring network or conventional interpolation methods. Observed wind fields were also compared with wind fields generated by Global Environmental Multiscale-High resolution Model Application Project (GEM-HiMAP) to explore the feasibility of using regional weather forecasting model simulated wind fields in LUR models when observed data are either sparse or not available. While GEM-HiMAP predicted wind fields well at large scales, it was unable to resolve wind flow patterns at smaller scales. These results suggest caution and careful evaluation of regional weather forecasting model simulated wind fields before incorporating into human exposure models for health studies. This study has demonstrated that wind fields may be integrated into the land use regression framework. Such integration has a discernable influence on both the overall model prediction and perhaps more importantly for health effects assessment on the relative spatial distribution of traffic pollution throughout the THUA. Methodology developed in this study may be applied in other large urban areas across the world.     

石家庄市道路交通环境NO_x污染水平及ARMA模型预测

选择石家庄市区代表性路段作为研究对象,对其交通环境空气中NOx的污染水平进行现状监测。基于Matlab软件建立拟合模型,对下一时期的NOx污染趋势进行预测。结果表明,石家庄市交通环境中NOx小时浓度介于0.047~0.237 mg/m3之间,呈早晚高,且下午明显低于上午的日变化规律;NOx日均浓度介于0.076~0.211 mg/m3之间,其浓度与车流量呈明显的正相关性。利用matlab软件建立的ARMA模型能够较好地预测道路交通环境空气中NOx的浓度变化趋势。     

Monte Carlo simulation of nitrogen oxides dispersion from a vehicular exhaust plume and its sensitivity studies

The pollutant dispersion behavior from the vehicular exhaust plume has a direct impact on human health, particularly to the drivers, bicyclists, motorcyclists, pedestrians, people working nearby and vehicle passengers. A two-dimensional pollutant dispersion numerical model was developed based on the joint-scalar probability density function (PDF) approach coupled with a k–ε turbulence model to simulate the initial dispersion process of nitrogen oxides, temperature and flow velocity distributions from a vehicular exhaust plume. A Monte Carlo algorithm was used to solve the PDF transport equations in order to obtain the dispersion distribution of nitrogen oxides concentration. The model was then validated by a series of sensitivity experimental studies in order to assess the effects of vehicular exhaust tailpipe velocities, wind speeds and chemistry on the initial dispersion of NO and NO₂ mass concentrations from the vehicular exhaust plume. The results show that the mass concentrations of nitrogen oxides decrease along the centerline of the vehicular exhaust plume in the downstream distance. The dispersion process can be enhanced when the vehicular exhaust tailpipe velocity is much larger than the wind speed. The oxidation reaction of NO plays an important role when the wind speed is large and the vehicular exhaust exit velocity is small, which leads to chemical reduction of NO, and the formation and accumulation of NO₂ in the exhaust plume. It is also found that the effect of vehicular exhaust-induced turbulence in the vicinity of the exhaust tailpipe exit is more dominant than the effect of wind turbulence, while the wind turbulence gradually shows a significant role for the dispersion of nitrogen oxides along with the development of exhaust plume. The range of dispersion of nitrogen oxides in the radial direction is increased along with the development of vehicular exhaust plume.     

PM Emissions Emanating from Limited-Access Highways

ABSTRACT

Motor vehicle contributions to primary particulate matter (PM) emissions include exhaust, tire wear, brake and clutch wear, and resuspended road dust. Relatively few field studies have been conducted to quantify fleetaverage exhaust emissions for actual on-road conditions. Therefore, direct measurements of motor vehicle-related PM emissions are warranted. In this study, PM₁₀ and PM_2.5 mass concentrations were measured near two major highways in the St. Louis area over the period from February–April 1997. Samplers were deployed both upwind and downwind of the roadways to capture the transport and dispersion of PM with distance from the roadway. The observed microscale concentration fields were compared to estimates using the PART5 emission factor model together with the CALINE4 highway dispersion model. Traffic- induced PM mass concentrations observed downwind of the roadway were always less than PART5/CALINE4 predictions; average percent differences for observed traffic-induced mass concentrations compared to predicted values were ?34% for PM_2.5 and -70% for PM₁₀. In most cases, the observed PM concentration decay with increasing distance from the roadway was steeper than predicted by dispersion modeling. Motor vehicle-induced emission factors were reconstructed by fitting CALINE4 to the observed concentration data with the emission factor as the sole adjustable parameter. Reconstructed fleet-average motor vehicle emission factors for the urban interstate highway were 0.03–0.04 g/VMT for both PM_2.5 and PM₁₀, while the fleet-average emission factors for the rural interstate highway were 0.2 and 0.3 g/VMT for PM_2.5 and PM₁₀, respectively.     

A measurement campaign in a street canyon in Helsinki and comparison of results with predictions of the OSPM model

In 1997, a measuring campaign was conducted in a street canyon (Runeberg St.) in Helsinki. Hourly mean concentrations of CO, NO_x, NO₂ and O₃ were measured at street and roof levels, the latter in order to determine the urban background concentrations. The relevant hourly meteorological parameters were measured at roof level; these included wind speed and direction, temperature and solar radiation. Hourly street level measurements and on-site electronic traffic counts were conducted throughout the whole of 1997; roof level measurements were conducted for approximately two months, from 3 March to 30 April in 1997. CO and NO_x emissions from traffic were computed using measured hourly traffic volumes and evaluated emission factors. The Operational Street Pollution Model (OSPM) was used to calculate the street concentrations and the results were compared with the measurements. The overall agreement between measured and predicted concentrations was good for CO and NO_x (fractional bias were −4.2 and +4.5%, respectively), but the model overpredicted the measured NO₂ concentrations (fractional bias was +22%). The agreement between the measured and predicted values was also analysed in terms of its dependence on wind speed and direction; the latter analysis was performed separately for two categories of wind velocity. The model qualitatively reproduces the observed behaviour very well. The database, which contains all measured and predicted data, is available for further testing of other street canyon dispersion models. The dataset contains a larger proportion of low wind speed cases, compared with other available street canyon measurement datasets.     

Assessment of ambient air quality in the port of Naples

Two experimental monitoring campaigns were carried out in 2012 to investigate the air quality in the port of Naples, the most important in southern Italy for traffic of passengers and one of the most important for goods. Therefore, it represents an important air pollution source located close to the city of Naples. The concentrations of sulfur dioxide (SO₂), nitrogen dioxide (NO₂), and BTEX (benzene, toluene, ethylbenzene, and xylenes) in the air were measured at 15 points inside the Naples port area through the use of passive samplers. In addition, a mobile laboratory was positioned in a fixed point inside the port area to measure continuous concentration of pollutants together with particulate matter, ambient parameters, and wind direction and intensity. The pollution levels monitored were compared with those observed in the urban area of Naples and in other Mediterranean ports. Even though the observation time was limited, measured concentrations were also compared with limit values established by European legislation. All the measured pollutants were below the limits with the exception of nitrogen dioxide: its average concentration during the exposition time exceeded the yearly limit value. A spatial analysis of data, according to the measured wind direction and intensity, provided information about the effects that ship emissions have on ambient air quality in the port area. The main evidence indicates that ship emissions influence sulfur dioxide concentration more than any other pollutants analyzed.

Implications: Two monitoring campaigns were carried out to measure BTEX, SO₂, NO₂, and PM₁₀ (particulate matter with an aerodynamic diameter <10 μm) air concentrations in the port of Naples. NO₂ hourly average and PM₁₀ daily average comply with European legislative standards. Spatial variation of pollutants long the axis corresponding to the prevailing wind direction seems to indicate a certain influence of ship emissions for SO₂. For NO₂ and PM₁₀, a correlation between concentrations in the harbor and those measured by the air quality monitoring stations sited in the urban area of Naples was observed, indicating a possible contribution of the near road traffic to the air pollution in the port of Naples.     

Regression modelling of hourly NOx and NO2 concentrations in urban air in London

Based on hourly measurements of NO_x NO₂ and O₃ and meteorological data, an ordinary least squares (OLS) model and a first-order autocorrelation (AR) model were developed to analyse the regression and prediction of NO_x and NO₂ concentrations in London. Primary emissions and wind speed are the most important factors influencing NO_x concentrations; in addition to these two, reaction of NO with O₃ is also a major factor influencing NO₂ concentrations. The AR model resulted in high correlation coefficients (R > 0.95) for the NO_x and NO₂ regression based on a whole year's data, and is capable of predicting NO₂ (R = 0.83) and NO_x (R = 0.65) concentrations when the explanatory variables were available. The analysis of the structure of regression models by Principal Component Analysis (PCA) indicates that the regression models are stable. The results of the OLS model indicate that there was an exceptional NO₂ source, other than primary emission and reaction of NO with O₃, in the air pollution episode in London in December 1991.     

An Atmospheric Dispersion Model for the Environmental Impact Assessment of Thermal Power Plants in Japan—A Method for Evaluating Topographical Effects

Abstract

An atmospheric dispersion model was developed for the environmental impact assessment of thermal power plants in Japan, and a method for evaluating topographical effects using this model was proposed. The atmospheric dispersion model consists of an airflow model with a turbulence closure model based on the algebraic Reynolds stress model and a Lagrangian particle dispersion model (LPDM). The evaluation of the maximum concentration of air pollutants such as SO₂, NO_x, and suspended particulate matter is usually considered of primary importance for environmental impact assessment. Three indices were therefore estimated by the atmospheric dispersion model: the ratios (α and β, respectively) of the maximum concentration and the distance of the point of the maximum concentration from the source over topography to the respective values over a flat plane, and the relative concentration distribution [γ(x)] along the ground surface projection of the plume axis normalized by the maximum concentration over a flat plane. The atmospheric dispersion model was applied to the topography around a power plant with a maximum elevation of more than 1000 m. The values of α and β evaluated by the atmospheric dispersion model varied between 1 and 3 and between 1 and 0.4, respectively, depending on the topographical features. These results and the calculated distributions of γ(x) were highly similar to the results of the wind tunnel experiment. Therefore, when the slope of a hill or mountain is similar to the topography considered in this study, it is possible to evaluate topographical effects on exhaust gas dispersion with reasonable accuracy using the atmospheric dispersion model as well as wind tunnel experiments.     

Modeling the formation,decay, and partitioning of semivolatile nitro-polycyclic aromatic hydrocarbons (nitronaphthalenes) in the atmosphere

A nitronaphthalene kinetics mechanism has been implemented and added to the photochemical smog mechanism, Carbon Bond-4. This mechanism was used to simulate the formation, decay, and partitioning of 1- and 2-nitronaphthalene and compare it to outdoor smog chamber data. The results suggest that these types of mechanisms can be used to model nitronaphthalene formation and decay in regional airmasses. The partitioning experiments were conducted at night. The sampling system consisted of two Teflon impregnated glass fiber filters followed by a gas-phase denuder. Evidence is provided that partitioning equilibrium is maintained even when the gas-phase components are decaying rapidly under sunlight. The photolysis rate constants were determined relative to k_NO2 to be 0.07×k_NO2 and 0.005×k_NO2 for 1- and 2-nitronaphthalene, respectively. Our results confirm that gas-phase photolysis is the major degradation pathway for 1-nitronaphthalene, whereas for 2-nitronaphthalene other pathways may also be important. The photochemical formation of nitronaphthalenes was studied using a mixture of naphthalene, propylene, NO_x, and diesel particles. 2-nitronaphthalene was observed to build up to higher levels than 1-nitronaphthalene, as the photodegradation of the latter was faster. Additionally, as a part of this study 1-nitronaphthalene has been identified and quantified in diesel exhaust.     

Air pollutant concentrations near three Texas roadways,Part I: Ultrafine particles

Vehicular emitted air pollutant concentrations were studied near three types of roadways in Austin, Texas: (1) State Highway 71 (SH-71), a heavily traveled arterial highway dominated by passenger vehicles; (2) Interstate 35 (I-35), a limited access highway north of Austin in Georgetown; and (3) Farm to Market Road 973 (FM-973), a heavily traveled surface roadway dominated by truck traffic. Air pollutants examined include carbon monoxide (CO), oxides of nitrogen (NO_x), and carbonyl species in the gas-phase. In the particle phase, ultrafine particle (UFP) concentrations (diameter < 100 nm), fine particulate matter (PM_2.5, diameter < 2.5 μm) mass and carbon content and several particle-bound organics were examined. All roadways had an upwind stationary sampling location, one or two fixed downwind sample locations and a mobile monitoring platform that characterized pollutant concentrations fall-off with increased distance from the roadways. Data reported in this paper focus on UFP while other pollutants and near-roadway chemical processes are examined in a companion paper. Traffic volume, especially heavy-duty traffic, wind speed, and proximity to the road were found to be the most important factors determining UFP concentrations near the roadways. Since wind directions were not consistent during the sampling periods, distances along wind trajectories from the roadway to the sampling points were used to study the decay characteristics of UFPs. Under perpendicular wind conditions, for all studied roadway types, particle number concentrations increased dramatically moving from the upwind side to the downwind side. The elevated particle number concentrations decay exponentially with increasing distances from the roadway with sharp concentration gradients observed within 100–150 m, similar to previously reported studies. A single exponential decay curve was found to fit the data collected from all three roadways very well under perpendicular wind conditions. No consistent pattern was observed for UFPs under parallel wind conditions. However, regardless of wind conditions, particle concentrations returned to background levels within a few hundred meters of the roadway. Within measured UFP size ranges, smaller particles (6–25 nm) decayed faster than larger ones (100–300 nm). Similar decay rates were observed among UFP number, surface, and volume.     

Assessment of tropospheric ozone at an industrial site of Chennai megacity

This paper presents the temporal variation in surface-level ozone (O₃) measured at Gummidipoondi near Chennai, Tamilnadu. The site chosen for the present study has high potential for ozone generation sources, such as vehicular traffic and industrial activities. The site is also located near a hazardous waste management facility. The key sources of nitrogen oxides (NO_x), which are considered to be an important precursor of O₃, include hazardous waste incineration, trucks bringing the hazardous wastes, and vehicles plying on the nearby National Highway 16 (NH 16). The measurements clearly showed diurnal variation, with maximum values observed during the noon hours and minimum values observed when solar radiation was less. The data showed a marked seasonal variation in O₃, with the highest hourly average O₃ concentration (497.2 µg/m³) in the summer season. Consequently, in order to identify the long-range transport sources adding to the increased O₃ levels, backward trajectories were computed using the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model. It was found that the polluted air mass originated from the Southeast Asian region and the Indo-Gangetic Plain. The polluted air mass, which advected large amounts of carbon monoxide (CO) plumes, was analyzed using the Measurement of Pollution in the Troposphere (MOPITT) retrievals. The correlations of O₃ with temperature (r = 0.746; P < 0.01) and solar radiation (r = 0.751; P < 0.01) were strongly positive, and that with NO_x was found to be negative. Stronger correlation of O₃ with NO_x was observed during pre-monsoon months (r = 0.627; P < 0.01) and following hours of photochemical reactions. There were substantial differences in concentrations between weekdays and weekends, with higher nitric oxide (NO) and nitrogen dioxide (NO₂), but lower O₃, concentrations on weekdays. A substantial weekday-weekend difference in O₃, which was higher on weekends, appears to be attributable to lower daytime traffic activity and hence reduced emissions of NO_x to a “NO_x-saturated” atmosphere.

Implications: The assessment of ground-level ozone in an industrial area with hazardous waste management facility is very important, as there is high possibility for more generation of tropospheric ozone. Since the location of the study area is coastal, wind plays a major role in O₃ transportation; hence, the effects of wind speed and wind direction have been studied in different seasons. When compared with the other studies carried out in different places across India, the present study area has recorded much greater O₃ mixing ratio. This study can be useful for setting up control strategies in such industrial areas.     

KAPPA-G,A Non-Gaussian Plume Dispersion Model: Description and Evaluation Against Tracer Measurements

This paper presents a mixed methodology for the simulation of atmospheric disperson phenomena in which vertical diffusion is computed using an analytical solution of the K-theory equation, while horizontal diffusion is simulated by the Gaussian formula. This new formulation, while maintaining a simple analytical form for the concentration field, incorporates the effects of power-law vertical profiles of both wind speed and eddy diffusivity. The performance of this approach, which has been implemented into a full computer package (KAPPA-G), is evaluated by comparison with data from SF₆ tracer experiments.     

A simple semi-empirical photochemical model for the simulation of ozone concentration in the Seoul metropolitan area in Korea

O₃ concentrations were simulated over the Seoul metropolitan area in Korea using a simple semi-empirical reaction (SEGRS) model which consists of generic reaction set (GRS), photochemical reaction set, and the diagnostic wind field generation model. The aggregated VOC emission strength was empirically scaled by the comparison of the simulated slope of (O₃–2NO–NO₂) concentration as a function of cumulative actinic light flux against measurements on high surface ozone concentration days with the relatively weak easterly geostrophic winds at the 850 hPa level in summer when the effect of horizontal advection was fairly small. The results indicated that the spatial distribution patterns and temporal variations of spatially averaged ground-level ozone concentrations were quite well simulated compared with those of observations with the modified volatile organic compound (VOC) emission strength. The diurnal trend of the surface ozone concentration and the maximum concentration compared observations were also quite reasonably simulated. However, the maximum ozone concentration occurring time at Seoul lagged about 2 h and the ozone concentration in the suburban area was slightly overestimated in the afternoon due to the influx of high ozone concentration from the urban area. It was found that the SEGRS model could be effectively used to simulate or predict the ground-level ozone concentration reasonably well without heavy computational cost provided the emission of ozone precursors are given.