Catalytic activities and mechanism of formaldehyde oxidation over gold supported on MnO<Subscript>2</Subscript> microsphere catalysts at room temperature

MnO₂ microspheres with various surface structures were prepared using the hydrothermal method, and Au/MnO₂ catalysts were synthesized using the sol-gel method. We obtained three MnO₂ microspheres and Au/MnO₂ samples: coherent solid spheres covered with wire-like nanostructures, solid spheres with nanosheets, and hierarchical hollow microspheres with nanoplatelets and nanorods. We investigated the properties and catalytic activities of formaldehyde oxidation at room temperature. Crystalline structures of MnO₂ are the main factor affecting the catalytic activities of these samples, and γ-MnO₂ shows high catalytic performance. The excellent redox properties are responsible for the catalytic ability of γ-MnO₂. The gold-supported interaction can change the redox properties of catalysts and accelerate surface oxygen species transition, which can account for the catalytic activity enhancement of Au/MnO₂. We also studied intermediate species. The dioxymethylene (DOM) and formate species formed on the catalyst surface were considered intermediates, and were ultimately transformed into hydrocarbonate and carbonate and then decomposed into CO₂. A proposed mechanism of formaldehyde oxidation over Au/MnO₂ catalysts was also obtained.     

NO conversion by positive streamer discharge—effects of gas compositions and reaction conditions

The effects of gas compositions and reaction conditions on NO conversion by positive streamer discharge were experimentally investigated by using a link tooth wheel-cylinder reactor. The results showed that NO conversion increased with increasing O₂ concentration and NH₃ concentration, but decreased with increasing inlet NO concentration and gas flow rate. The addition of CO₂ or H₂O to the feed gas promoted NO conversion by increasing the maximum discharge voltage, and NH₄NO₃ was formed in the presence of NH₃. There was a most suitable range interval between discharge tooth wheels if both NO conversion and energy consumption were considered. Increasing applied voltage resulted in the increase in the amount of O₃ generated by streamer discharge.     

Abatement of mixed volatile organic compounds in a catalytic hybrid surface/packed-bed discharge plasma reactor

In this study, post plasma-catalysis degradation of mixed volatile organic compounds (benzene, toluene, and xylene) has been performed in a hybrid surface/packed-bed discharge plasma reactor with Ag-Ce/g-Al₂O₃ catalyst at room temperature. The effect of relative air humidity on mixed VOCs degradation has also been investigated in both plasma-only and PPC systems. In comparison to the plasma-only system, a significant improvement can be observed in the degradation performance of mixed VOCs in PPC system with Ag-Ce/γ-Al₂O₃ catalyst. In PPC system, 68% benzene, 89% toluene, and 94% xylene were degraded at 800 J·L^–1, respectively, which were 25%, 11%, and 9% higher than those in plasma-only system. This result can be attributed to the high catalytic activity of Ag-Ce/γ-Al₂O₃ catalyst to effectively decompose O₃ and lead to generating more reactive species which are capable of destructing the VOCs molecules completely. Moreover, the presence of Ag-Ce/γ-Al₂O₃ catalyst in plasma significantly decreased the emission of discharge byproducts (NO_x and O₃) and promoted the mineralization of mixed VOCs towards CO₂. Adding a small amount of water vapor into PPC system enhanced the degradation efficiencies of mixed VOCs, however, further increasing water vapor had a negative impact on the degradation efficiencies, which was primarily attributed to the quenching of energetic electrons by water vapor in plasma and the competitive adsorption of water vapor on the catalyst surface. Meanwhile, the catalysts before and after discharge were characterized by the Brunauer-Emment-Teller and X-ray photoelectron spectroscopy.

Open image in new window

     

Characterization and performance of V2O5/CeO2 for NH3-SCR of NO at low temperatures

A series of CeO₂ supported V₂O₅ catalysts with various loadings were prepared with different calcination temperatures by the incipient impregnation. The catalysts were evaluated for low temperature selective catalytic reduction (SCR) of NO with ammonia (NH₃). The effects of O₂ and SO₂ on catalytic activity were also studied. The catalysts were characterized by specific surface areas (S_BET) and X-ray diffraction (XRD) methods. The experimental results showed that NO conversion changed significantly with the different V₂O₅ loading and calcination temperature. With the V₂O₅ loading increasing from 0 to 10 wt%, NO conversion increased significantly, but decreased at higher loading. The optimum calcination temperature was 400°C. The best catalyst yielded above 80% NO conversion in the reaction temperature range of 160°C–300°C. The formation of CeVO₄ on the surface of catalysts caused the decrease of redox ability.     

介质阻挡放电-催化降解苯的研究

采用双介质阻挡放电管 ,当含苯气体的流量为 1 5L·min- 1 ,放电电压在 60 0 0V—1 2 0 0 0V范围内 ,放电管温度在 2 1 0℃左右 ,研究介质阻挡放电 催化降解苯的协同效应 .结果表明 ,在余辉区中放入催化剂 ,60 0 0V的电压下 ,苯的降解率可达 70 % ,产物中CO/CO2为 0 0 5 ;而在同样电压下 ,不放入催化剂 ,苯的降解率仅为 5 5 %左右 ,CO/CO2 约为 0 5 .由此可见 ,催化剂在余辉区时能与等离子体协同作用 ,促进苯的降解     

Role of Rh promoter on increasing stability of Au/Al2O3 catalyst for CO oxidation at low temperature

The Au/Al₂O₃ and Au–Rh/Al₂O₃ catalysts were prepared by deposition–precipitation. The promotional effect of Rh on the performance of the Au/Al₂O₃ catalyst for CO oxidation was studied. The results indicate that using Au/Al₂O₃ catalyst, CO can be completely oxidized at 0°C or much lower temperature but the catalyst deactivated very fast. Rh can improve the stability of Au/Al₂O₃ catalyst more than 10 times, which gives an important hint to develop high stable catalyst for CO oxidation at low temperature.     

Investigation of fluorescence characterization and electrochemical behavior on the catalysts of nanosized Pt-Rh/γ-Al2O3 to oxidize gaseous ammonia

This work describes the environmentally friendly technology for oxidation of ammonia (NH₃) to form nitrogen at temperatures range from 423K to 673K by selective catalytic oxidation (SCO) over a nanosized Pt-Rh/γ-Al₂O₃ catalyst prepared by the incipient wetness impregnation method of hexachloroplatinic acid (H₂PtCl₆) and rhodium (III) nitrate (Rh(NO₃)₃) with γ-Al₂O₃ in a tubular fixed-bed flow quartz reactor (TFBR). The characterization of catalysts were thoroughly measured using transmission electron microscopy (TEM), threedimensional excitation-emission fluorescent matrix (EEFM) spectroscopy, UV-Vis absorption, dynamic lightscattering (DLS), zeta potential meter, and cyclic voltammetry (CV). The results demonstrated that at a temperature of 673K and an oxygen content of 4%, approximately 99% of the NH₃ was removed by catalytic oxidation over the nanosized Pt-Rh/γ-Al₂O₃ catalyst. N₂ was the main product in NH₃-SCO process. Further, it reveals that the oxidation of NH₃ was proceeds by the over-oxidation of NH₃ into NO, which was conversely reacted with the NH₃ to yield N₂. Therefore, the application of nanosized Pt-Rh/γ-Al₂O₃ catalyst can significantly enhance the catalytic activity toward NH₃ oxidation. One fluorescent peak for fresh catalyst was different with that of exhausted catalyst. It indicates that EEFM spectroscopy was proven to be an appropriate and effective method to characterize the Pt clusters in intrinsic emission from nanosized Pt-Rh/γ-Al₂O₃ catalyst. Results obtained from the CV may explain the significant catalytic activity of the catalysts.     

Chemical deactivation of V2O5-WO3/TiO2 SCR catalyst by combined effect of potassium and chloride

V₂O₅-WO₃/TiO₂ catalyst was poisoned by impregnation with NH₄Cl, KOH and KCl solution, respectively. The catalysts were characterized by X-ray diffraction (XRD), inductively coupled plasma (ICP), N₂ physisorption, Raman, UV-vis, NH₃ adsorption, temperature-programmed reduction of hydrogen (H₂-TPR), temperature-programmed oxidation of ammonia (NH₃-TPO) and selective catalytic reduction of NO _x with ammonia (NH₃-SCR). The deactivation effects of poisoning agents follow the sequence of KCl>KOH?NH₄Cl. The addition of ammonia chloride enlarges the pore size of the titania support, and promotes the formation of highly dispersed V = O vanadyl which improves the oxidation of ammonia and the high-temperature SCR activity. K⁺ ions are suggested to interact with vanadium and tungsten species chemically, resulting in a poor redox property of catalyst. More importantly, potassium can reduce the Brønsted acidity of catalysts and decrease the stability of Brønsted acid sites significantly. The more severe deactivation of the KCl-treated catalyst can be mainly ascribed to the higher amount of potassium resided on catalyst.     

Selective catalytic reduction of NO x from exhaust of lean-burn engine over Ag-Al2O3/cordierite catalyst

A highly effective Ag-Al₂O₃ catalyst was prepared using the in-situ sol-gel method, and characterized by surface area using nitrogen adsorption, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) techniques. The catalyst performance was tested on a real lean-burn gasoline engine. Only unburned hydrocarbons and carbon monoxide in the exhaust were directly used as reductant (without any external reductant), the maximum NO _x conversion could only reach 40% at 450°C. When an external reductant, ethanol was added, the average NO _x conversion was greater than 60%. At exhaust gas temperature range of 350–500°C, the maximum NO _x conversion reached about 90%. CO and HC could be efficiently oxidized with Pt-Al₂O₃ oxidation catalyst placed at the end of SCR converter. However, NO _x conversion drastically decreased because of the oxidation of some intermediates to NO _x again. The possible reaction mechanism was proposed as two typical processes, nitration, and reduction in HC-SCR over Ag-Al₂O₃.     

Removal of acid yellow 36 using Box–Behnken designed photoelectro-Fenton: a study on removal mechanisms

Photoelectro-Fenton was applied for the removal of acid yellow 36 (AY36) from synthetic aqueous solution using iron electrodes. A Box–Behnken design was used for optimization of the effects of pH, H₂O₂ concentration, current density, and reaction time. Individual effects of these variables were more important than their interaction effects. The derived model was in good agreement with the experimental results. Total organic carbon was determined in solution and sludge in order to clarify the removal mechanism. Increase of H₂O₂ concentration and current density led to domination of oxidation and coagulation mechanisms, respectively. The effects of scavenging and inhibiting agents were also investigated: (1) presence of alcohols can reduce the efficiency through competition with dye for reaction with hydroxyl radicals; (2) anions (NO₃^?, HCO₃^?, and H₂PO₄^?) scavenged hydroxyl radicals and reduced decolorization of AY36.     

Removal of toluene from air streams by cobalt-copper bimetallic catalysts supported on sepiolite

Abstract

Oxidative removal of toluene using copper and cobalt bimetallic catalysts with varying molar ratios supported on sepiolite was investigated. The catalysts prepared by a deposition precipitation method and were characterized using X-ray diffraction, nitrogen adsorption-desorption, field emission scanning electron microscopy, H₂-temperature-programmed reduction, transmission electron microscope, and inductive coupled plasma atomic emission spectroscopy. The species supported on sepiolite are Co₃O₄, CuO, and CuCo₂O₄. The activities of the tested catalysts increased in the order 0Co-4Cu/Sep <1Co-3Cu/Sep <4Co-0Cu/Sep <1Co-1Cu/Sep <3Co-1Cu/Sep. The latter exhibiting 90% toluene oxidative degradation at 288?°C within 15?h, having high selectivity towards CO₂, and being stable at 300?°C up to 15?h. In conclusion, this study showed that sepiolite has excellent properties as a support.     

Adsorptive behaviors of humic acid onto freshly prepared hydrous manganese dioxides

This study focused on the adsorptive behaviors of humic acid onto freshly prepared hydrous MnO₂(s) (δMnO₂), and investigated the feasibility of employing δMnO₂ for humic acid removal from drinking water. Effects of such parameters as molecular mass of humic acid, kinds of divalent cations on adsorptive behaviors and possible mechanisms involved were investigated. This study indicated that humic acid with higher molecular mass exhibited more tendency of adsorbing onto δMnO₂ than that with lower molecular mass. Ca²⁺ facilitated more humic acid adsorption than Mg²⁺; UV-Vis spectra analysis indicated higher capabilities of Ca²⁺ coordinating with acidic functional groups of humic acid than that of Mg²⁺. Additionally, ζ potential characterization indicated that Ca²⁺ showed higher potential of increasing gz potential of δMnO₂ than Mg²⁺. Ca²⁺ of 1.0 mmol/L increased ζ potential of δMnO₂ from ?37 mV (pH 7.9) to +7 mV (pH 7.2), while 1.0 mmol/L Mg²⁺ increased to lower value as ?9 mV (pH 6.5), correspondingly. Fourier transform infrared (FTIR) spectra demonstrated the adsorption of humic acid onto δMnO₂, showing the important roles of-COO^? functional groups and surface Mn-OH in the adsorption of humic acid onto δMnO₂.     

Studies on catalytic reduction of nitrate in groundwater

Catalytic reduction of nitrate in groundwater by sodium formate over the catalyst was investigated. Pd-Cu/γ-Al₂O₃ catalyst was prepared by impregnation and characterized by brunauer-emmett-teller (BET), inductive coupled plasma (ICP), X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray (EDX). It was found that total nitrogen was effectively removed from the nitrate solution (100 mg/L) and the removal efficiency was 87%. The catalytic activity was affected by pH, catalyst amount used, concentration of sodium formate, and initial concentration of nitrate. As sodium formate was used as reductant, precise control in the initial pH was needed. Excessively high or low initial pH (7.0 or 3.0) reduced catalytic activity. At initial pH of 4.5, catalytic activity was enhanced by reducing the amount of catalyst, while concentrations of sodium formate increased with a considerable decrease in N₂ selectivity. In which case, catalytic reduction followed the first order kinetics.     

Degradation of chlorinated phenols by nanoscale zero-valent iron

Chlorophenols (CPs), as important contaminants in groundwater, are toxic and difficult to biodegrade. Recently nanoscale zero-valent iron received a great deal of attention because of its excellent performance in treating recalcitrant compounds. In this study, nanoscale zero-valent iron particles were prepared using chemical reduction, and the reductive transformations of three kinds of chlorinated phenols (2-CP, 3-CP, and 4-CP) by nanoscale zero-valent iron under different conditions were investigated. The transformation process of the CPs was shown to be dechlorination first, then cleavage of the benzene ring. The removal efficiency of the CPs varied as follows: 2-CP > 3-CP > 4-CP. The reactivity of CPs was associated with their energy of lowest unoccupied molecular orbit (E _LUMO). With the increase in initial concentrations of CPs, removal efficiency decreased a little. But the quantities of CPs reduced increased evidently. Temperature had influence on not only the removal efficiency, but also the transformation pathway. At higher temperatures, dechlorination occurred prior to benzene ring cleavage. At lower temperatures, however, the oxidation product was formed more easily.     

Thermochemical conversion of municipal solid waste into energy and hydrogen: a review

The rising global population is inducing a fast increase in the amount of municipal waste and, in turn, issues of rising cost and environmental pollution. Therefore, alternative treatments such as waste-to-energy should be developed in the context of the circular economy. Here, we review the conversion of municipal solid waste into energy using thermochemical methods such as gasification, combustion, pyrolysis and torrefaction. Energy yield depends on operating conditions and feedstock composition. For instance, torrefaction of municipal waste at 200 °C generates a heating value of 33.01 MJ/kg, while the co-pyrolysis of cereals and peanut waste yields a heating value of 31.44 MJ/kg at 540 °C. Gasification at 800 °C shows higher carbon conversion for plastics, of 94.48%, than for waste wood and grass pellets, of 70–75%. Integrating two or more thermochemical treatments is actually gaining high momentum due to higher energy yield. We also review reforming catalysts to enhance dihydrogen production, such as nickel on support materials such as CaTiO₃, SrTiO₃, BaTiO₃, Al₂O₃, TiO₃, MgO, ZrO₂. Techno-economic analysis, sensitivity analysis and life cycle assessment are discussed.

     

Pathway of the ozonation of 2,4,6-trichlorophenol in aqueous solution

The reaction mechanism and pathway of the ozonation of 2,4,6-trichlorophenol (2,4,6-TCP) in aqueous solution were investigated. The removal efficiency and the variation of H₂O₂, Cl^? formic acid, and oxalic acid were studied during the semi-batch ozonation experiments (continuous for ozone gas supply, fixed volume of water sample). The results showed that when there was no scavenger, the removal efficiency of 0.1 mmol/L 2,4,6-TCP could reach 99% within 6 min by adding 24 mg/L ozone. The reaction of molecular ozone with 2,4,6-TCP resulted in the formation of H₂O₂. The maximal concentration of H₂O₂ detected during the ozonation could reach 22.5% of the original concentration of 2,4,6-TCP. The reaction of ozone with H₂O₂ resulted in the generation of a lot of OH? radicals. Therefore, 2,4,6-TCP was degraded to formic acid and oxalic acid by ozone and OH? radicals together. With the inhibition of OH? radicals, ozone molecule firstly degraded 2,4,6-TCP to form chlorinated quinone, which was subsequently oxidized to formic acid and oxalic acid. Two reaction pathways of the degradation of 2,4,6-TCP by ozone and O₃/OH? were proposed in this study.     

Degradation of endocrine disruptor bisphenol A in drinking water by ozone oxidation

The ozone oxidation of endocrine disruptor bisphenol A in drinking water was investigated. A stainless completely mixed reactor was employed to carry out the degradation experiments by means of a batch model. With an initial concentration of 11.0 mg/L, the removal efficiencies of BPA (bisphenol A) could be measured up to 70%, 82%, and 90% when the dosages of ozone were 1, 1.5, and 2 mg/L, respectively. The impacts on BPA degradation under the conditions of different ozone dosages, water background values, BPA initial concentrations, and ozone adding time were analyzed. The results showed that ozone dosage plays a dominant role during the process of BPA degradation, while the impact of the contact time could be ignored. UV wavelength scanning was used to confirm that the by-products were produced, which could be absorbed at UV254. The value of UV254 was observed to have changed during the ozonation process. Based on the change of UV254, it could be concluded that BPA is not completely degraded at low ozone dosage, while shorter adding time of total ozone dosage, high ozone dosage, and improvement of dissolved ozone concentration greatly contribute to the extent of BPA degradation. The effects of applied H₂O₂ dose in ozone oxidation of BPA were also examined in this study. The O₃-H₂O₂ processes proved to have similar effects on the degradation of BPA by ozone oxidation.     

Urea formation from carbon dioxide and ammonia at atmospheric pressure

Urea synthesis, currently the largest use of carbon dioxide in organic synthesis, is conventionally operated at high pressure and high temperature. Here, we report for the first time that urea forms at atmosphere and ambient temperatures by negative corona discharge in gas phase. The conversion of CO₂ and yields of a solid mixture of urea and ammonium carbamate, which was identified by the ¹³C NMR spectrum, rise with reducing temperatures and increasing molar ratios of NH₃/CO₂ and discharge frequencies. The conversion of carbon dioxide was found to be 82.16?% at 20?°C and 1?atm with a molar flow ratio of n(NH₃)/n(CO₂) of 2.5. High pressure and high temperature as energy inputs are not necessary.     

New insights into mercury removal mechanism on CeO<Subscript>2</Subscript>-based catalysts: A first-principles study

First-principles calculations were performed to investigate the mechanism of Hg⁰ adsorption and oxidation on CeO₂(111). Surface oxygen activated by the reduction of Ce⁴⁺ to Ce³⁺ was vital to Hg⁰ adsorption and oxidation processes. Hg0 was fully oxidized by the surface lattice oxygen on CeO₂(111), without using any other oxidizing agents. HCl could dissociate and react with the Hg adatom on CeO₂(111) to form adsorbed Hg–Cl or Cl–Hg–Cl groups, which promoted the desorption of oxidized Hg and prevented CeO₂ catalyst deactivation. In contrast, O–H and H–O–H groups formed during HCl adsorption consumed the active surface oxygen and prohibited Hg oxidation. The consumed surface oxygen was replenished by adding O₂ into the flue gas. We proposed that oxidized Hg desorption and maintenance of sufficient active surface oxygen were the rate-determining steps of Hg⁰ removal on CeO₂-based catalysts. We believe that our thorough understanding and new insights into the mechanism of the Hg⁰ removal process will help provide guidelines for developing novel CeO₂-based catalysts and enhance the Hg⁰ removal efficiency.

Open image in new window

     

Enhanced heterogeneous Fenton-like activity by Cu-doped BiFeO<Subscript>3</Subscript> perovskite for degradation of organic pollutants

Heterogeneous Fenton-like reaction has been extensively investigated to eliminate refractory organic contaminants in wastewater, but it usually shows low catalytic performance due to difficulty in reduction from Fe(III) to Fe(II). In this study, enhanced catalytic efficiency was obtained by employing Cu-doped BiFeO₃ as heterogeneous Fenton-like catalysts, which exhibited higher catalytic performance toward the activation of H₂O₂ for phenol degradation than un-doped BiFeO₃. BiFe_0.8Cu_0.2O₃ displayed the best performance, which yielded 91% removal of phenol (10 mg L^–1) in 120 min. The pseudo first-order kinetic rate constant of phenol degradation in BiFe_0.8Cu_0.2O₃ catalyzed heterogeneous Fenton-like reaction was 5 times higher than those of traditional heterogeneous Fenton-like catalysts, such as Fe₃O₄ and goethite. The phenol degradation efficiency could still reach 83% after 4 cycles, which implied the good stability of BiFe_0.8Cu_0.2O₃. The high catalytic activity of BiFe_0.8Cu_0.2O₃ was attributed to the fact that the doping Cu into BiFeO₃ could promote the generation of Fe(II) in the catalyst and then facilitate the activation of H₂O₂ to degrade the organic pollutants.

Open image in new window