氯元素对烟气中汞的形态和分布的影响

采用化学热力平衡分析方法研究了在煤燃烧在气化过程中产生的瀵气里痕量元素汞的形态及分布，在一个大气压下，400K－2000K温度范围里，研究了汞－煤系统和汞－煤－氯系统中汞在还原性气氛和氧化性气氛的烟气中的化学形态和分布，着重探讨了煤中的氯元素对汞在烟气中的形态和分布的影响，化学热力平衡分析结果表明，在煤燃烧和气化的最高温度区域里，单质汞是示是主要形式，少量的氯元素可以大大地增强汞元素的蒸发;在气化的还原性气氛烟气中，汞的主要形式是单质汞，在氧化性气氛的燃煤烟气中随着在烟气中温度的降低，单质汞将发生化学反应而生成氯化汞；烟气中氯元素的含量越大，氯化汞作为稳定相的温度范围越宽。     

Evaluation of mercury speciation and removal through air pollution control devices of a 190 MW boiler

Air pollution control devices (APCDs) are installed at coal-fired power plants for air pollutant regulation. Selective catalytic reduction (SCR) and wet flue gas desulfurization (FGD) systems have the co-benefits of air pollutant and mercury removal. Configuration and operational conditions of APCDs and mercury speciation a ect mercury removal e ciently at coal-fired utilities. The Ontario Hydro Method (OHM) recommended by the U.S. Environmental Protection Agency (EPA) was used to determine mercury speciation simultaneously at five sampling locations through SCR-ESP-FGD at a 190 MW unit. Chlorine in coal had been suggested as a factor a ecting the mercury speciation in flue gas; and low-chlorine coal was purported to produce less oxidized mercury (Hg2+) and more elemental mercury (Hg0) at the SCR inlet compared to higher chlorine coal. SCR could oxidize elemental mercury into oxidized mercury when SCR was in service, and oxidation e ciency reached 71.0%. Therefore, oxidized mercury removal e ciency was enhanced through a wet FGD system. In the non-ozone season, about 89.5%–96.8% of oxidized mercury was controlled, but only 54.9%–68.8% of the total mercury was captured through wet FGD. Oxidized mercury removal e ciency was 95.9%–98.0%, and there was a big di erence in the total mercury removal e ciencies from 78.0% to 90.2% in the ozone season. Mercury mass balance was evaluated to validate reliability of OHM testing data, and the ratio of mercury input in the coal to mercury output at the stack was from 0.84 to 1.08.     

燃煤电厂超低排放改造前后汞污染排放特征

针对300 MW燃煤机组,基于US EPA(美国国家环境保护局)的30 B汞监测方法,通过多点监测对比了实施低氮燃烧器改造、SCR脱硝改造、新增低温省煤器、静电除尘器高频电源改造、湿法脱硫塔脱硫提效并增加管式除雾、新增湿式静电除尘器技术路线开展的超低排放改造前后汞排放及分布特征.研究表明:超低排放改造前,神华煤w(Hg)为49 μg/kg,烟囱入口ρ(Hg)测量值为1.87 μg/m3;煤燃烧及经过污染物控制单元后,有35.0%的汞存在于灰中,有29.5%的汞存在于石膏中,有35.4%的汞从烟囱排出.超低排放改造后,神华煤中w(Hg)为30 μg/kg,烟囱入口ρ(Hg)测量值为0.46 μg/m3;脱硫进水及湿式除尘器进水对汞平衡几乎没有影响,煤燃烧及经过污染物控制单元后,有36.1%的汞存在于灰中,有55.2%的汞存在于石膏中,有8.7%的汞从烟囱排出.超低排放改造后,污染物控制设备的烟气综合脱汞效率提高了1.5倍左右,表明超低排放脱硝增强了对汞的催化氧化,而脱硫增强了对二价汞的吸收结果.湿式电除尘器对脱汞没有明显效果.      

过渡金属元素掺杂改性SCR对零价汞的催化氧化性能

为提高商用SCR催化剂对Hg0(零价汞)的催化氧化活性,研究了过渡金属对其进行掺杂改性的方法,并利用固定床反应平台考察了不同试验条件下改性催化剂对Hg0的氧化效率. 结果表明:Y、Zn、Ni和Zr等过渡金属的掺杂可明显抑制SCR催化剂的催化活性,而Fe、Cu掺杂改性SCR催化剂对Hg0的催化氧化性能有显著提升. 在反应温度为350 ℃、空速比为370 000 h-1、φ(HCl)为1×10-5的条件下,Fe、Cu掺杂改性的SCR催化剂对Hg0的氧化效率均能达到90%以上,并且Fe掺杂改性后的SCR催化剂的脱硝性能也未受到明显影响. 借助XRD和XPS等表征手段,对反应前后Fe掺杂改性SCR催化剂进行了研究,表明Fe改性SCR催化剂遵循Mars-Maessen和Langmuir-Hinshelwood机制,可明显提高对Hg0的催化氧化效率,因此,应用前景较好.      

燃煤烟气污染物控制装置协同脱汞特性研究

采用Ontario Hydro方法对某100MW燃煤机组进行了烟气汞取样测试,获得了选择性催化还原（SCR）脱硝装置、静电除尘器（ESP）和湿法烟气脱硫装置（WFGD）对烟气汞形态转化和脱除特性规律.借助程序升温脱附（TPD）、扫描电子显微镜分析（SEM）和X射线荧光光谱分析（XRF）等方法探究了飞灰对汞的吸附特性及吸附后汞的热稳定性.结果表明,在75% MCR和85% MCR不同的机组负荷下,SCR+ESP+WFGD对烟气总汞（Hg^T）的联合脱除率分别为92.83%、81.66%.SCR对元素汞（Hg⁰）的氧化率与燃煤氯（Cl）含量正相关,Cl含量为500mg/kg时,氧化率高达96.18%.ESP在完全脱除颗粒汞（Hg^P）的同时对Hg⁰和氧化态汞（Hg²⁺）的平均脱除率分别为12.73%和27.79%,ESP飞灰中的未燃尽炭和金属氧化物（Al₂O₃、Fe₂O₃）是吸附气态汞的关键组分,汞在飞灰表面主要以HgCl₂、HgS（红色）和HgO的形态存在,高于190℃时会分解再释放.WFGD对Hg²⁺的平均脱除率为91.10%,并能将部分Hg²⁺还原成Hg⁰,存在明显的汞二次释放问题.     

强化SCR脱硝催化剂转化零价汞的初步研究

常规的选择性还原脱硝(SCR)催化剂对烟气中的零价汞具有一定的催化氧化作用,从而有利于提高下游的除汞效率。但在烟气HCl浓度较低时,SCR催化剂对燃煤烟气中的零价汞催化氧化效果较差。为了提高SCR催化剂对零价汞的催化氧化效果,在现有SCR催化剂基础上,通过负载其它金属元素的方法,对其进行改性掺杂。结果发现,负载锰氧化物的Mn/SCR催化剂,对零价汞的催化氧化作用明显提高,而将其再掺杂Mo后,其催化氧化性能得到更进一步提高。在反应温度350℃的条件下,加入7.5 mg/m3HCl,Mo-Mn/SCR对零价汞的催化氧化效率接近90%,而常规SCR催化剂只有35%左右。另外,Mo只有在与Mn结合使用,其促进作用才能较显著地体现出来。对改性后的SCR催化剂的脱硝性能研究表明,掺杂Mo-Mn元素对于SCR的脱硝性能无明显影响。     

基于国内实测燃煤电厂烟气汞排放估算的不确定度

参照测量不确定度评定与表示的国家技术规范,基于近年来我国燃煤电厂常规污控设备协同脱汞的现场测试数据(文献报道和实测值)及各省原煤w(汞)的实测值,初步构建了国内燃煤电厂烟气汞排放不确定度的计算方法,并以2010年的燃煤量、污控方式布局为基础,计算了该年度汞排放的不确定度. 结果表明:2010年我国燃煤电厂烟气汞排放的总不确定度为48.8t,占平均排放总量的34.3%;其中60.2%源于污控设备脱汞效率的不确定度,39.8%源于原煤w(汞)的不确定度;采用ESP(静电除尘)、ESP+WFGD(静电除尘+湿法脱硫)、SCR+ESP+WFGD(选择性催化还原脱硝+静电除尘+湿法脱硫)和FF(袋式除尘)大气污控组合的机组各存在6.0、32.2、9.7和0.9t的烟气汞排放不确定度,分别占各对应机组烟气汞排放量的19.3%、32.8%、84.6%和53.6%,其中SCR+ESP+WFGD污控组合烟气汞排放的相对不确定度最大. 随着我国烟气脱硝工作全面推行,2015年以后,SCR+ESP+WFGD污控措施(组合)的机组所占比例将会提高到66%以上,如果仍以现有数据为基础,则来自SCR+ESP+WFGD污控措施(组合)机组的烟气汞排放不确定度将会大幅增加,因此急需增加对该类装置脱汞效率的实测样本数量.      

Economic analysis of atmospheric mercury emission control for coal-fired power plants in China

Coal combustion and mercury pollution are closely linked, and this relationship is particularly relevant in China, the world's largest coal consumer. This paper begins with a summary of recent China-specific studies on mercury removal by air pollution control technologies and then provides an economic analysis of mercury abatement from these emission control technologies at coal-fired power plants in China. This includes a cost-effectiveness analysis at the enterprise and sector level in China using 2010 as a baseline and projecting out to 2020 and 2030. Of the control technologies evaluated, the most cost-effective is a fabric filter installed upstream of the wet flue gas desulfurization system (FF + WFGD). Halogen injection (HI) is also a cost-effective mercury-specific control strategy, although it has not yet reached commercial maturity. The sector-level analysis shows that 193 tons of mercury was removed in 2010 in China's coal-fired power sector, with annualized mercury emission control costs of 2.7 billion Chinese Yuan. Under a projected 2030 Emission Control (EC) scenario with stringent mercury limits compared to Business As Usual (BAU) scenario, the increase of selective catalytic reduction systems (SCR) and the use of HI could contribute to 39 tons of mercury removal at a cost of 3.8 billion CNY. The economic analysis presented in this paper offers insights on air pollution control technologies and practices for enhancing atmospheric mercury control that can aid decision-making in policy design and private-sector investments.     

干法烟气脱硫副产物中汞的形态分布

通过分析干法烟气脱硫副产物中不同形态汞的含量,研究干法脱硫灰中汞的环境稳定性. 利用逐级化学提取法,分析了锅炉底灰、锅炉飞灰、脱硫塔底灰和除尘器灰中水溶态、酸溶态、过氧化氢溶态及王水溶残渣态汞的含量,研究了不同形态汞含量的变化规律. 结果表明,锅炉底灰、锅炉飞灰、脱硫塔底灰和除尘器灰中w（总汞）分别为0.23,0.36,0.46和1.22 mg/kg,且随着脱硫除尘时间的延长w（总汞）呈增加的趋势,其中,以氯化物、硝酸盐和硫酸盐存在的水溶态汞变化明显,除尘器灰中w（水溶态汞）高达0.72 mg/kg. 分析认为,干法烟气脱硫灰吸附的大部分汞蒸气转化为可溶性的氯化物、硝酸盐和硫酸盐等,另外还有少量汞以单质状态存在.      

燃煤烟气中零价汞控制技术研究进展

我国燃煤过程中汞的排放越来越引起国际社会的广泛关注。燃煤烟气中排放汞的形态主要以零价汞为主,将气态零价汞转化为易于脱除的二价汞是控制零价汞排放的有效途径。为此,文章对燃煤烟气中零价汞的转化机理以及控制技术现状进行了概括和总结,对不同零价汞控制技术的特点进行比较分析,并初步探讨了其发展趋势。结论得出应充分利用现有的烟气净化设备,经济有效地发挥其在烟气除汞方面的作用。     

《火电厂大气污染物排放标准》实施对燃煤电厂大气汞减排的影响

为评估GB 13223─2011《火电厂大气污染物排放标准》实施对燃煤电厂大气Hg(汞)减排的影响,采用“自下而上”排放因子法,对燃煤电厂大气Hg排放量进行了估算,通过设计不同发展情景,对排放标准实施条件下我国燃煤电厂大气Hg减排量(不含港澳台地区数据,下同)进行了预测. 结果表明:不同能耗情景下,预计2015年燃煤电厂的煤炭消费量为18.5×108~20.3×108 t,2020年煤炭消费量可达19.7×108~22.5×108 t;GB 13223─2011实施后,大气污染控制设施包括ESP(静电除尘器)、FF(袋式除尘器)、WFGD(湿法脱硫)和SCR(选择性催化还原脱硝)的应用比例亟需提高,控制设施面临提效改造,主要控制技术组合SCR+ESP+WFGD在2015年和2020年的应用比例将达到40%、75%;改造后技术组合FF+WFGD、ESP+WFGD、SCR+ESP+WFGD可分别实现90%、85%、80%的脱Hg效率. 由此可为我国燃煤电厂大气Hg排放带来巨大的协同减排潜力,与2010年约119 t的排放水平相比,2015年和2020年在低能耗情景下,我国燃煤电厂大气Hg减排幅度可分别高达38%和39%. 为进一步提高燃煤电厂大气的Hg减排量,建议逐步推广应用活性炭喷射(ACI)等技术.      

基于实测的燃煤电厂汞排放特性分析与研究

选取我国6个有代表性的燃煤电厂进行现场实测,依据现场监测的汞排放浓度数据计算得出每个燃煤电厂汞的脱除率和汞平均排放因子,从而得出这6个燃煤电厂汞排放特性,为将来我国汞排放控制提供支持和依据.6个燃煤电厂的汞排放浓度为4.72～14.54μg/m3,汞脱除效率为20.89%～70.63%,汞排放因子为14.09～56.0...     

Metal chlorides loaded on activated carbon to capture elemental mercury

Activated carbon (AC) was considered to be an effective sorbent to control mercury in combustion systems. However, its capture capacity was low and it required a high carbon-to-mercury mass ratio. AC loaded with catalyst showed a high elemental mercury (Hg0) capture capacity due to large surface area of AC and high oxidization ability of catalyst. In this study, several metal chlorides and metal oxides were used to promote the sorption capacity of AC. As a result, metal chlorides were better than metal oxides loaded on AC to remove gaseous mercury. X-ray diffractometer (XRD), thermogravimetric analyzer (TGA) and specific surface area by Brunauer- Emmett-Teller method (BET) analysis showed the main mechanisms: first, AC had an enormous surface area for loading enough MClx; second, Cl and MxOy were generated during pyrogenation of MClx; finally, there were lots of active elements such as Cl and MxOy which could react with elemental mercury and convert it to mercury oxide and mercury chloride. The HgO and HgCl2 might be released from AC’s porous structure by thermo regeneration. A catalytic chemisorption mechanism predominates the sorption process of elemental mercury. As Co and Mn were valence variable metal elements, their catalytic effect on Hg0 oxidization may accelerate both oxidation and halogenation of Hg0. The sorbents loaded with metal chlorides possessed a synergistic function of catalytic effect of valence variable metal and chlorine oxidation.     

贵阳市小型燃煤锅炉烟气中汞的形态及释放

选择贵阳市某厂的1台安装有湿法脱硫除尘的燃煤锅炉,研究湿法脱硫除尘前后燃煤烟气中颗粒态汞(Hgp)、氧化态汞(Hg2+)、原子态汞(Hg0)以及总汞(Hgt)的含量和形态分布。结果显示,湿法脱硫除尘后的颗粒态汞、氧化态汞、原子态汞分别约占总汞的10 4%,6 0%,83 6%。湿法脱硫除尘器对氧化态汞与颗粒态汞有很好的去除效率(分别为87 9%,76 1%),而对原子态汞的去除效率较差(为30 4%)。由于对该锅炉的年燃煤量统计有一定的误差以及烟气采样分析方法本身存在的误差,该锅炉输出的总汞略大于输入的总汞,质量平衡结果为:输出输入=103 6%～107 4%。煤经过燃烧后,总汞的释放因子为:41 7%残留在底灰中,65 7%进入烟气中,其中经过湿法脱硫除尘器的净化,26 7%的汞随除尘废水排放到水环境中,7 8%存在于经过除尘后的渣中,25 05%随清洁烟气释放到大气中。      

碳汞比对燃煤烟气中Hg脱除影响的实验研究

利用吸附反应器和袋式除尘器联合脱汞系统,研究了活性炭喷射对模拟烟气中元素汞的脱除影响。实验表明,吸附反应器对元素汞的脱除起主要作用,并且脱汞效率随碳汞比的增加而提高;碳汞比的变化对除尘器的脱汞效率影响不大。在碳汞比为4 000、6 000、8 000下,系统的脱汞效率分别为39.9%、42.5%、47.3%。实验同时探讨了除尘器滤袋上粉尘层的存在对脱汞效率的影响,结果表明:在表面过滤速度为0.98 m/min的实验条件下,在碳汞比为4 000、6 000、8 000下,粉尘层的脱汞效率分别为:3.65%、3.20%、3.66%。     

燃煤电厂烟气汞的排放及控制研究

随着环保意识的增强,燃煤电厂汞污染越来越受到人们的关注,对燃煤电厂烟气汞污染的控制也逐渐成为热点。介绍了燃煤电厂烟气中汞的排放形态及特性,分析了燃煤电厂烟气汞形态转化的影响因素,综述了有关燃煤电厂烟气中汞污染控制技术及研究进展,讨论了燃烧前脱汞、燃烧中脱汞和燃烧后脱汞技术,特别分析了利用现有烟气脱硫设备吸收法脱汞、吸附法脱汞、催化氧化脱汞的技术,并对燃煤电厂烟气脱汞技术的前景进行了展望,提出结合现有烟气净化设备同时脱汞的设想。     

Mercury removal from coal combustion flue gas by modified fly ash

Fly ash is a potential alternative to activated carbon for mercury adsorption. The effects of physicochemical properties on the mercury adsorption performance of three fly ash samples were investigated. X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, and other methods were used to characterize the samples. Results indicate that mercury adsorption on fly ash is primarily physisorption and chemisorption. High specific surface areas and small pore diameters are beneficial to efficient mercury removal. Incompletely burned carbon is also an important factor for the improvement of mercury removal efficiency, in particular. The C-M bond, which is formed by the reaction of C and Ti, Si and other elements, may improve mercury oxidation. The samples modified with CuBr2 , CuCl 2 and FeCl3 showed excellent performance for Hg removal, because the chlorine in metal chlorides acts as an oxidant that promotes the conversion of elemental mercury (Hg0) into its oxidized form (Hg2+). Cu2+ and Fe3+ can also promote Hg 0 oxidation as catalysts. HCl and O2 promote the adsorption of Hg by modified fly ash, whereas SO2 inhibits the Hg adsorption because of competitive adsorption for active sites. Fly ash samples modified with CuBr2 , CuCl2 and FeCl3 are therefore promising materials for controlling mercury emissions.     

添加CaCl2对烟气净化装置联合脱汞的规律分析

煤炭燃烧向大气中排放了大量汞。为了探究经济有效的汞排放控制方法,在管式炉中进行了CaCl₂晶体的水解实验,CaCl₂在一定温度和气氛下会水解产生HCl,HCl有利于烟气中Hg0的氧化。且随着反应温度的增加,水解率呈上升趋势。在流化床炉中进行了CaCl₂溶液蒸发协同脱汞实验。CaCl₂溶液喷洒在燃煤中可显著提高SCR脱销装置对Hg0的氧化率;煤中喷洒CaCl₂溶液可提高烟气中Hg2+的浓度和占比,从而提高湿法烟气脱硫装置（WFGD）对气态Hg的脱除效果。相比于喷洒在原煤中,将CaCl₂溶液喷洒在布袋除尘器（FF）前的蒸发干燥塔中,可显著提高FF脱除Hg的效果。整体上看,当温度越高,氯添加比越高时,烟气净化装置协同脱汞的效率也越高。     

大气颗粒物中汞的赋存形态及其依存条件

于2004—2007年在上海市西南部某采样点使用分级采样器和PM₁₀采样器采集大气颗粒物样品,采用化学序批式提取法分析了颗粒物中的ExPM(可交换汞)、HPM(可溶盐酸汞)、EPM(元素汞)和RPM(剩余汞)4种形态汞的含量. 结果表明:颗粒物中ρ(total-Hg)(total-Hg为总汞)在0.07~1.44ng/m3之间,47.8%集中在粒径<1.6μm的颗粒物中;颗粒物中w(total-Hg)在0.35~6.89μg/g之间,高于煤炭和水泥中的含量; 颗粒物中ρ(total-Hg)在冬、春季较高,夏季较低; PM₁₀中ρ(total-Hg)日变化呈双峰型,然而w(total-Hg)的日变化并不明显.夜间各种形态汞的质量浓度都高于白天.汞的形态受气象条件和污染源分布的影响. 除了2006年春季外,其他年份各季节的w(HPM)基本持平;ρ(EPM)在2005年冬季和2006年春季均出现较高值,分别为0.19和0.17ng/m3. HPM和EPM主要集中在细颗粒物上,而RPM在粒径<1.6μm和1.6~<3.7μm颗粒物中的分布无明显差异. 颗粒物中的ρ(total-Hg)、ρ(RPM)与温度、日温差、相对湿度呈显著负相关,与ρ(SO₂)呈正相关;但ρ(HPM)和ρ(EPM)与这些参数的相关性不同. 这可能与HPM和EPM的来源与大气化学特征有关,其中,HPM易溶解于液相,与对光照依赖性很强的光化学反应有关;而EPM主要取决于一次来源的贡献和气态汞沉积速率.      

我国煤中汞含量水平及洗选过程汞流向分析

介绍了我国煤中汞含量与分布特征、煤中汞的赋存形态,分析了汞释放对环境的影响以及汞的脱除与控制技术。结果表明:我国(华南)晚三叠世(T3)煤中汞含量最高,平均含量为0.26μg/g;贫煤和无烟煤中汞含量最高,平均含量都超过0.20μg/g。含汞较高的晚三叠世、晚二叠世煤田主要分布于华南各地;多数煤中汞含量在0.300μg/g以下,但华南的江西、广西、贵州等地煤中汞含量总体水平较高;汞的赋存形态可分为有机结合态和无机结合态,煤中汞的控制方法可分为利用前脱汞、利用(燃烧)后脱汞和过程中汞形态转化。提出了煤炭洗选过程汞分布、脱除率和汞平衡等计算公式,指出了煤炭洗选过程中汞迁移行为的主要影响因素。