Plant-accelerated dissipation of phenanthrene and pyrene from water in the presence of a nonionic-surfactant

Plant-accelerated dissipation of phenanthrene and pyrene in water in the presence of a nonionic-surfactant (Brij35) was studied. The mechanisms involved were evaluated, based on the investigation of plant uptake of these compounds from water with Brij35. The presence of ryegrass (Lolium multiflorum Lam) clearly enhanced the dissipation of tested PAHs in water with 0-296 mg l(-1) Brij35. The first-order rate constants (K), calculated from the first-order kinetic models for these PAH degradation (all significant at P < 0.05, n=8), of phenanthrene and pyrene in the presence of ryegrass were 16.7-50% and 47.1-108% larger than those of plant-free treatments, whereas half-lives (T1/2) of the former were 14.3-33.4% and 32.0-52.0% smaller than the latter, respectively. However, the promotion of PAH dissipation by ryegrass was found to significantly decrease with increasing Brij35 concentrations. In the range of 0-296 mg l(-1), low concentrations (< or = 74.0 mg l(-1)) of Brij35 generally enhanced plant uptake and accumulation of phenanthrene and pyrene, based on the observed plant concentrations and accumulated amounts of these chemicals from water. In contrast, Brij35 at relatively high concentrations (> or = 148 mg l(-1)) markedly restricted plant uptake of these PAHs. Plant accumulation of phenanthrene and pyrene accounted for 6.21-35.0% and 7.66-24.3% of the dissipation enhancement of these compounds from planted versus unplanted water bodies. In addition, plant metabolism was speculated to be another major mechanism of plant-accelerated dissipation of these PAHs in water systems. Results obtained from this study provided some insight with regard to the feasibility of phytoremediation for PAH contaminated water bodies with coexisted contaminants of surfactants.     

Biodegradation of phenanthrene in river sediment

The aerobic biodegradation potential of phenanthrene (a polycyclic aromatic hydrocarbon [PAH]) in river sediment was investigated in the laboratory. Biodegradation rate constants (k1) and half-lives (t1/2) for phenanthrene (5 microg/g) in sediment samples collected at five sites along the Keelung River in densely populated northern Taiwan ranged from 0.12 to 1.13 l/day and 0.61 to 5.78 day, respectively. Higher biodegradation rate constants were noted in the absence of sediment. Two of the sediment samples were capable of biodegrading phenanthrene at initial concentrations 5-100 microg/g; lower biodegradation rates occurred at higher concentrations. Optimal biodegradation conditions were determined as 30 degreesC and pH 7.0. Biodegradation was not significantly influenced by the addition of such carbon sources as acetate, pyruvate, and yeast extract, but was significantly influenced by the addition of ammonium, sulfate, and phosphate. Results show that anthracene, fluorene, and pyrene biodegradation was enhanced by the presence of phenanthrene, but that phenanthrene treatment did not induce benzo[a]pyrene biodegradation during a 12-day incubation period.     

Prediction of phenanthrene uptake by plants with a partition-limited model

The performance of a partition-limited model on prediction of phenanthrene uptake by a wide variety of plant species was evaluated using a greenhouse study. The model predictions of root or shoot concentrations for tested plant species were all within an order of magnitude of the observed values. Modeled root concentrations appeared to be more accurate than modeled shoot concentrations. The differences of simulated and experimented concentrations of phenanthrene in roots and shoots of three representative plant species, including ryegrass, flowering Chinese cabbage, and three-colored amaranth, were less than 81% for roots and 103% for shoots. Results are promising in that the alpha(pt) values of the partition-limited model for root uptake of phenanthrene correlate well with root lipid contents. Additionally, a significantly positive correlation is also observed between root concentration factors (RCFs, defined as the ratio of contaminant concentrations in root and in soil on a dry weight basis) of phenanthrene and root lipid contents. Results from this study suggest that the partition-limited model may have potential applications for predicting the plant PAH concentration in contaminated sites.     

Remediation of PAH contaminated soils: application of a solid-liquid two-phase partitioning bioreactor

The feasibility of a two-step treatment process has been assessed at laboratory scale for the remediation of soil contaminated with a model mixture of polycyclic aromatic hydrocarbons (PAHs) (phenanthrene, pyrene, and fluoranthene). The initial step of the process involved contacting contaminated soil with thermoplastic, polymeric pellets (polyurethane). The ability of three different mobilizing agents (water, surfactant (Biosolve) and isopropyl alcohol) to enhance recovery of PAHs from soil was investigated and the results were compared to the recovery of PAHs from dry soil. The presence of isopropyl alcohol had the greatest impact on PAH recovery with approximately 80% of the original mass of PAHs in the soil being absorbed by the polymer pellets in 48 h. The second stage of the suggested treatment involved regeneration of the PAH loaded polymers via PAH biodegradation, which was carried out in a solid-liquid two-phase partitioning bioreactor. In addition to the PAH containing polymer pellets, the bioreactor contained a microbial consortium that was pre-selected for its ability to degrade the model PAHs and after a 14 d period approximately 78%, 62% and 36% of phenanthrene, pyrene, and fluoranthene, respectively, had been desorbed from the polymer and degraded. The rate of phenanthrene degradation was shown to be limited by mass transfer of phenanthrene from the polymer pellets. In case of pyrene and fluoranthene a combination of mass transfer and biodegradation rate might have been limiting.     

Laboratory studies to characterize the efficacy of sand capping a coal tar-contaminated sediment

Placement of a microbial active sand cap on a coal tar-contaminated river sediment has been suggested as a cost effective remediation strategy. This approach assumes that the flux of contaminants from the sediment is sufficiently balanced by oxygen and nutrient fluxes into the sand layer such that microbial activity will reduce contaminant concentrations within the new benthic zone and reduce the contaminant flux to the water column. The dynamics of such a system were evaluated using batch and column studies with microbial communities from tar-contaminated sediment under different aeration and nutrient inputs. In a 30-d batch degradation study on aqueous extracts of coal tar sediment, oxygen and nutrient concentrations were found to be key parameters controlling the degradation rates of polycyclic aromatic hydrocarbons (PAHs). For the five PAHs monitored (naphthalene, fluorene, phenanthrene, anthracene, and pyrene), degradation rates were inversely proportional to molecular size. For the column studies, where three columns were packed with a 20-cm sand layer on the top of a 5 cm of sediment layer, flow was established to sand layers with (1) aerated water, (2) N(2) sparged water, or (3) HgCl(2)-sterilized N(2) sparged water. After steady-state conditions, PAH concentrations in effluents were the lowest in the aerated column, except for pyrene, whose concentration was invariant with all effluents. These laboratory scale studies support that if sufficient aeration can be achieved in the field through either active and passive means, the resulting microbially active sand layer can improve the water quality of the benthic zone and reduce the flux of many, but not all, PAHs to the water column.     

Contamination of polycyclic aromatic hydrocarbons (PAHs) in microlayer and subsurface waters along Alexandria coast,Egypt

The residues of seven polycyclic aromatic hydrocarbons (PAHs) pollutants in microlayer and subsurface seawater samples collected from Alexandria coast, Egypt, were analyzed by gas chromatography–electron-impact mass spectrometry-selected ion monitoring mode (GC–MS-SIM). The pollutants studied were, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene and benzo[a]pyrene. Total PAH levels in microlayer ranged from 103 to 523 ng/l, while it ranged in subsurface samples from 13 to 120 ng/l. The Western Harbor location recorded the highest level of PAHs pollutant over all the other location for both subsurface and microlayer waters. The two major PAHs in microlayer water at the Western Harbor were fluorene and phenanthrene, making up 27% and 20% of the total PAHs, while the two major PAHs in subsurface water at the Eastern Harbor were phenanthrene and fluoranthene recording up 21% each of the total PAHs. The total PAH levels were generally in the nano-gram per liter for microlayer and subsurface seawater samples. The dominant PAHs in both subsurface and microlayer samples were fluoranthene, pyrene and benzo[a]pyrene. The microlayer enrichment factor at Alexandria’s Mediterranean coast was ranged from 29 for fluorene to 3 for phenanthrene and benzo[a]pyrene which showed PAHs concentration in the microlayer with an average of five times more than the total PAH in the subsurface samples.     

Evaluation of methods to determine adsorption of polycyclic aromatic hydrocarbons to dispersed carbon nanotubes

A number of methods have been reported for determining hydrophobic organic compound adsorption to dispersed carbon nanotubes (CNTs), but their accuracy and reliability remain uncertain. We have evaluated three methods to investigate the adsorption of phenanthrene (a model polycyclic aromatic hydrocarbon, PAH) to CNTs with different physicochemical properties: dialysis tube (DT) protected negligible depletion solid phase microextraction (DT-nd-SPME), ultracentrifugation, and filtration using various types of filters. Dispersed CNTs adhered to the unprotected polydimethylsiloxane (PDMS)-coated fibers used in nd-SPME. Protection of the fibers from CNT adherence was investigated with hydrophilic DT, but high PAH sorption to the DT was observed. The efficiency of ultracentrifugation and filtration to separate CNTs from the water phase depended on CNT physicochemical properties. While non-functionalized CNTs were efficiently separated from the water phase using ultracentrifugation, incomplete separation of carboxyl functionalized CNTs was observed. Filtration efficiency varied with different filter types (composition and pore size), and non-functionalized CNTs were more easily separated from the water phase than functionalized CNTs. Sorption of phenanthrene was high (< 70%) for three of the filters tested, making them unsuitable for the assessment of phenanthrene adsorption to CNTs. Filtration using a hydrophilic polytetrafluoroethylene (PTFE) filter membrane (0.1 μm) was found to be a simple and precise technique for the determination of phenanthrene adsorption to a range of CNTs, efficiently separating all types of CNTs and exhibiting a good and highly reproducible recovery of phenanthrene (82%) over the concentration range tested (70–735 μg/L).

     

Study of metabolites from the degradation of polycyclic aromatic hydrocarbons (PAHs) by bacterial consortium enriched from mangrove sediments

The PAH metabolites produced during degradation of fluorene, phenanthrene and pyrene by a bacterial consortium enriched from mangrove sediments were analyzed using the on-fiber silylation solid-phase microextraction (SPME) combining with gas chromatography–mass spectrometry (GC–MS) method. Seventeen metabolites at trace levels were identified in different PAH degradation cultures based on the full scan mass spectra. In fluorene degradation cultures, 1-, 2-, 3- and 9-hydroxyfluorene, fluorenone, and phthalic acid were detected. In phenanthrene and pyrene degradation cultures, various common metabolites such as phenanthrene and pyrene dihydrodiols, mono-hydroxy phenanthrene, dihydroxy pyrene, lactone and 4-hydroxyphenanthrene, methyl ester, and phthalic acid were found. The detection of various common and novel metabolites demonstrates that SPME combining with GC–MS is a quick and convenient method for identification as well as monitoring the real time changes of metabolite concentrations throughout the degradation processes. The knowledge of PAH metabolic pathways and kinetics within indigenous bacterial consortium enriched from mangrove sediments contributes to enhance the bioremediation efficiency of PAH in real environment.     

Importance of heterocylic aromatic compounds in monitored natural attenuation for coal tar contaminated aquifers: A review

NSO heterocycles (HET) are typical constituents of coal tars. However, HET are not yet routinely monitored, although HET are relatively toxic coal tar constituents. The main objectives of the study is therefore to review previous studies and to analyse HET at coal tar polluted sites in order to assess the relevance of HET as part of monitored natural attenuation (MNA) or any other long-term monitoring programme. Hence, natural attenuation of typical HET (indole, quinoline, carbazole, acridine, methylquinolines, thiophene, benzothiophene, dibenzothiophene, benzofuran, dibenzofuran, methylbenzofurans, dimethylbenzofurans and xanthene) were studied at three different field sites in Germany. Compound-specific plume lengths were determined for all main contaminant groups (BTEX, PAH and HET). The results show that the observed plume lengths are site-specific and are above 250m, but less than 1000m. The latter, i.e. the upper limit, however mainly depends on the level of investigation, the considered compound, the lowest measured concentration and/or the achieved compound-specific detection limit and therefore cannot be unequivocally defined. All downstream contaminant plumes exhibited HET concentrations above typical PAH concentrations indicating that some HET are generally persistent towards biodegradation compared to other coal tar constituents, which results in comparatively increased field-derived half-lives of HET. Additionally, this study provides a review on physicochemical and toxicological parameters of HET. For three well investigated sites in Germany, the biodegradation of HET is quantified using the centre line method (CLM) for the evaluation of bulk attenuation rate constants. The results of the present and previous studies suggest that implementation of a comprehensive monitoring programme for heterocyclic aromatic compounds is relevant at sites, if MNA is considered in risk assessment and for remediation.     

Enhanced desorption of phenanthrene from soils using hydroxypropyl-beta-cyclodextrin: experimental results and model predictions

Objective of this study was to evaluate the effects of hydroxypropyl-beta-cyclodextrin (HPCD) on the removal of phenanthrene from solid phase. Batch tests for the phenanthrene distribution between aqueous and solid phase were conducted in the presence of HPCD. Column tests and numerical simulations were conducted to evaluate the roles of HPCD cavities and interaction rates between water, HPCD, and solid phase in the enhanced removal of phenanthrene. Experimental results showed that HPCD was effective in removing sorbed phenanthrene from subsurface environment, primarily due to its negligible sorption to the solid phase and the partitioning of phenanthrene into HPCD cavities. From the numerical simulations, it was found that rate-limited partitioning of phenanthrene into HPCD cavities was most influential factor in the enhanced elution of phenanthrene. Sorption and desorption rate of phenanthrene between aqueous and solid phase was very fast or near equilibrium state. Interaction rates of contaminant between water, HPCD, and solid phase could be affected by other factors such as soil types and organic matter contents. Results from this study implied that HPCD flushing could be effectively applied for the removal of hydrophobic organic pollutants existing in the soils as sorbed or NAPL state.     

Electrokinetic enhancement of phenanthrene biodegradation in creosote-polluted clay soil

Given the difficulties caused by low-permeable soils in bioremediation, a new electrokinetic technology is proposed, based on laboratory results with phenanthrene, to afford bioremediation of polycyclic aromatic hydrocarbons (PAH) in clay soils. Microbial activity in a clay soil historically polluted with creosote was promoted using a specially designed electrokinetic cell with a permanent anode-to-cathode flow and controlled pH. The rates of phenanthrene losses during treatment were tenfold higher in soil treated with an electric field than in the control cells without current or microbial activity. Results from experiments with Tenax-assisted desorption and mineralization of 14C-labeled phenanthrene indicated that phenanthrene biodegradation was limited by mass-transfer of the chemical. We suggest that the enhancement effect of the applied electric field on phenanthrene biodegradation resulted from mobilization of the PAH and nutrients dissolved in the soil fluids.     

Effect of pH control at the anode for the electrokinetic removal of phenanthrene from kaolin soil

Polycyclic aromatic hydrocarbon (PAH)-contaminated soils exist at numerous sites, and these sites may threaten public health and the environment because many PAH compounds are toxic, mutagenic, and/or carcinogenic. PAHs are also hydrophobic and persistent, so conventional remediation methods are often costly or inefficient, especially when the contaminants are present in low permeability and/or organic soils. An innovative technique, electrokinetically enhanced in situ flushing, has the potential to increase soil-solution-contaminant interaction and PAH removal efficiency for low permeability soils; however, the electrolysis reaction at the anode may adversely affect the remediation of low acid buffering capacity soils, such as kaolin. Therefore, the objective of this study was to improve the remediation of low acid buffering soils by controlling the pH at the anode to counteract the electrolysis reaction. Six bench-scale electrokinetic experiments were conducted, where each test employed one of three different flushing solutions, deionized water, a surfactant, or a cosolvent. For each of these solutions, tests were performed with and without a 0.01 M NaOH solution at the anode to control the pH. The test using deionized water with pH control generated a higher electroosmotic flow than the equivalent test performed without pH control, but the electroosmotic flow difference between the surfactant and cosolvent tests with and without pH control was minor compared to that observed with the deionized water tests. Controlling the pH was beneficial for increasing contaminant solubilization and migration from the soil region adjacent to the anode, but the high contaminant concentrations that resulted in the middle or cathode soil regions indicates that subsequent changes in the soil and/or solution chemistry caused contaminant deposition and low overall contaminant removal efficiency.     

Polycyclic aromatic hydrocarbon removal from water by natural fiber sorption.

The use of two natural sorbents, kapok and cattail fibers, were investigated for polycyclic aromatic hydrocarbon (PAH) removal from water. Naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, and fluoranthene were the PAHs studied. For comparative purposes, a commercial polyester fiber sorbent was included in the investigation. The PAH sorption and retention capabilities of the three fibers were determined through batch and continuous-flow experiments under non-competitive and competitive conditions. In the batch experiments, cattail fiber was the most effective sorbent. Kapok fiber provided the lowest PAH retention, while cattail fiber had slightly less PAH retention than polyester fiber. When two PAHs were present in the same system, a competitive effect on the much less hydrophobic PAH was observed. Similar results were obtained in the column experiments, except that polyester fiber performed much poorer on naphthalene. Cattail fiber is a promising sorbent for treating PAH-contaminated water, such as urban runoff.     

PAH dissipation in spiked soil: impacts of bioavailability, microbial activity, and trees

While trees have demonstrated potential in phytoremediation of several organic contaminants, little is known regarding their ability to impact the common soil contaminant PAHs. Several species of native North American trees were planted in soil artificially contaminated with three PAHs. Plant biomass, PAH dissipation, and microbial mineralization were monitored over the course of one year and environmental conditions were allowed to follow typical seasonal patterns. PAH dissipation and mineralization were not affected by planting. Extensive and rapid loss of PAHs was observed and attributed to high bioavailability and microbial activity in all treatments. The rate of this loss may have masked any significant planting effects. Anthracene was found to be more recalcitrant than pyrene or phenanthrene. Parallel soil aging studies indicated that sequestration to soil components was minimal. Contrary to common inferences in literature, amendment with decaying fine roots inhibited PAH degradation by the soil microbial community. Seasonal variation in environmental factors and rhizosphere dynamics may have also reduced or negated the effect of planting and should be taken into account in future phytoremediation trials. The unique root traits of trees may pose a challenge to traditional thought regarding PAH dissipation in the rhizosphere of plants.     

Enhanced Desorption of Phenanthrene from Soils Using Hydroxypropyl‐β‐cyclodextrin: Experimental Results and Model Predictions

Objective of this study was to evaluate the effects of hydroxypropyl‐β‐cyclodextrin (HPCD) on the removal of phenanthrene from solid phase. Batch tests for the phenanthrene distribution between aqueous and solid phase were conducted in the presence of HPCD. Column tests and numerical simulations were conducted to evaluate the roles of HPCD cavities and interaction rates between water, HPCD, and solid phase in the enhanced removal of phenanthrene. Experimental results showed that HPCD was effective in removing sorbed phenanthrene from subsurface environment, primarily due to its negligible sorption to the solid phase and the partitioning of phenanthrene into HPCD cavities. From the numerical simulations, it was found that rate‐limited partitioning of phenanthrene into HPCD cavities was most influential factor in the enhanced elution of phenanthrene. Sorption and desorption rate of phenanthrene between aqueous and solid phase was very fast or near equilibrium state. Interaction rates of contaminant between water, HPCD, and solid phase could be affected by other factors such as soil types and organic matter contents. Results from this study implied that HPCD flushing could be effectively applied for the removal of hydrophobic organic pollutants existing in the soils as sorbed or NAPL state.     

Modelling the atmospheric fate and seasonality of polycyclic aromatic hydrocarbons in the UK

This paper presents the results from an exercise in atmospheric contaminant fate modelling, which had three main objectives: (1) to investigate the balance between estimated national atmospheric emissions of six selected PAHs and observed ambient measurements for the UK, as a means of testing the current emission estimates; (2) to investigate the potential influence of seasonally dependent environmental fate processes on the observed seasonality of air concentrations; and (3) after undertaking the first two objectives, to make inferences about the likely magnitude of seasonal differences in sources. When addressing objective 1 with annually averaged emissions data, it appeared that the UK PAH atmospheric emissions inventory was reasonably reliable for fluorene, fluoranthene, pyrene, benzo[a]pyrene and benzo[ghi]perylene--but not so for phenanthrene. However, more detailed analysis of the seasonality in environmental processes which may influence ambient levels, showed that the directions and/or magnitudes of the predicted seasonality did not coincide with field observations. This indicates either that our understanding of the environmental fate and behaviour of PAHs is still limited, and/or that there are uncertainties in the emissions inventories. It is suggested that better quantification of PAH sources is needed. For 3- and 4-ringed compounds, this should focus on those sources which increase with temperature, such as volatilisation from soil, water, vegetation and urban surfaces, and possible microbially-mediated formation mechanisms. The study also suggests that the contributions of inefficient, diffusive combustion processes (e.g. domestic coal/wood burning) may be underestimated as a source of the toxicologically significant higher molecular weight species in the winter. It is concluded that many signatory countries to the UNECE POPs protocol (which requires them to reduce national PAH emissions to 1990 levels) will experience difficulties in demonstrating compliance, because source inventories for 1990 and contemporary situations are clearly subject to major uncertainties.     

A laboratory study of sediment and contaminant release during gas ebullition

Significant quantities of gas are generated from labile organic matter in contaminated sediments. The implications for the gas generation and subsequent release of contaminants from sediments are unknown but may include enhanced direct transport such as pore water advection and diffusion. The behavior of gas in sediments and the resulting migration of a polyaromatic hydrocarbon, viz phenanthrene, were investigated in an experimental system with methane injection at the base of a sediment column. Hexane above the overlying water layer was used to trap any phenanthrene migrating out of the sediment layer. The rate of suspension of solid particulate matter from the sediment bed into the overlying water layer was also monitored. The experiments indicated that significant amounts of both solid particulate matter and contaminant can be released from a sediment bed by gas movement with the amount of release related to the volume of gas released. The effective mass transfer coefficient of gas bubble-facilitated contaminant release was estimated under field conditions, being around three orders of magnitude smaller than that of bioturbation. A thin sand-capping layer (2 cm) was found to dramatically reduce the amount of contaminant or particles released with the gas because it could prevent or at least reduce sediment suspension. Based on the experimental observations, gas bubble-facilitated contaminant transport pathways for both uncapped and capped systems were proposed. Sediment cores were sliced to obtain phenanthrene concentration. X-ray computed tomography (CT) was used to investigate the void space distribution in the sediment penetrated by gas bubbles. The results showed that gas bubble migration could redistribute the sediment void spaces and may facilitate pore water circulation in the sediment.     

Solubilization, solution equilibria, and biodegradation of PAH's under thermophilic conditions

Biodegradation rates of PAHs are typically low at mesophilic conditions and it is believed that the kinetics of degradation is controlled by PAH solubility and mass transfer rates. Solubility tests were performed on phenanthrene, fluorene and fluoranthene at 20 degrees C, 40 degrees C and 60 degrees C and, as expected, a significant increase in the equilibrium solubility concentration and of the rate of dissolution of these polycyclic aromatic hydrocarbons (PAHs) was observed with increasing temperature. A first-order model was used to describe the PAH dissolution kinetics and the thermodynamic property changes associated with the dissolution process (enthalpy, entropy and Gibb's free energy of solution) were evaluated. Further, other relevant thermodynamic properties for these PAHs, including the activity coefficients at infinite dilution, Henry's law constants and octanol-water partition coefficients, were calculated in the temperature range 20-60 degrees C. In parallel with the dissolution studies, three thermophilic Geobacilli were isolated from compost that grew on phenanthrene at 60 degrees C and degraded the PAH more rapidly than other reported mesophiles. Our results show that while solubilization rates of PAHs are significantly enhanced at elevated temperatures, the biodegradation of PAHs under thermophilic conditions is likely mass transfer limited due to enhanced degradation rates.     

Contamination of polycyclic aromatic hydrocarbons in surface sediments of mangrove swamps

The concentrations of total polycyclic aromatic hydrocarbons (sigmaPAHs) and 15 individual PAH compounds in 20 surface sediments collected from four mangrove swamps in Hong Kong were analysed. sigmaPAH concentrations ranged from 356 to 11,098 ng g(-1) dry weight with mean and median values of 1992 and 1,142 ng g(-1), respectively. These values were significantly higher than those of marine bottom sediments of Hong Kong harbours, suggesting that more PAHs were accumulated in mangrove surface sediments. The concentrations of sigmaPAHs as well as individual PAH compound varied significantly among mangrove swamps. The swamps heavily polluted by livestock and industrial sewage, such as Ho Chung and Mai Po, had much higher concentrations of total PAHs and individual PAH than the other swamps. The PAH profiles were similar among four mangrove swamps, and were dominated by naphthalene (two-ring PAH), fluorene and phenanthrene (three-ring PAH). The mangrove sediments had higher percentages of low-molecular-weight PAHs. These indicated that PAHs in mangrove sediments might originate from oil or sewage contamination (petrogenic input). Ratio values of specific PAH compounds such as phenanthrene/anthracene and fluoranthene/ pyrene, were calculated to evaluate the possible source of PAH contamination in mangrove sediments. These ratios varied among samples, suggesting that mangrove sediments might have a mixed pattern of pyrolytic and petrogenic inputs of PAHs. Sediments collected from Ho Chung mangrove swamp appeared to be more dominated by pyrolytic input while those from Tolo showed strong petrogenic contamination.