Application of the Fenton’s process in a bubble column reactor for hydroquinone degradation

The aim of this study was to assess the degradation and mineralization of hydroquinone (HQ) by the Fenton’s process in a bubble column reactor (BCR). The effect of the main operating variables, namely, air flow rate, effluent volume, hydrogen peroxide (H₂O₂) concentration, catalyst (Fe²⁺) dose, initial pH, and temperature, were assessed. For all air flow rates tested, no concentration gradients along the column were noticed, evidencing that a good mixing was reached in the BCR. For the best conditions tested ([H₂O₂] = 500 mg/L, [Fe²⁺] = 45 mg/L, T = 24 °C, Q _air = 2.5 mL/min, pH = 3.0, and V = 5 L), complete HQ degradation was reached, with ~ 39% of total organic carbon (TOC) removal, and an efficiency of the oxidant use—η _H2O2—of 0.39 (ratio between TOC removed per H₂O₂ consumed normalized by the theoretical stoichiometric value); moreover, a non-toxic effluent was generated. Under these conditions, the intermediates and final oxidation compounds identified and quantified were a few carboxylic acids, namely, maleic, pyruvic, and oxalic. As a strategy to improve the TOC removal, a gradual dosage of the optimal H₂O₂ concentration was implemented, being obtained ~ 55% of mineralization (with complete HQ degradation). Finally, the matrix effect was evaluated, for which a real wastewater was spiked with 100 mg/L of HQ; no reduction in terms of HQ degradation and mineralization was observed compared to the solution in distilled water.     

Application of chemical oxidation to remediate HCH-contaminated soil under batch and flow through conditions

This is the first study describing the chemical oxidation of hexachlorocyclohexanes (HCHs) in contaminated soil under water saturated and unsaturated flow through conditions. Soil contaminated with β-HCH (45 mg kg^?1) and γ-HCH (lindane, 25 mg kg^?1) was sampled from former lindane waste storage site. Efficiency of following treatments was tested at circumneutral pH: H₂O₂ alone, H₂O₂/Fe^II, Na₂S₂O₈ alone, Na₂S₂O₈/Fe^II, and KMnO₄. Experimental conditions (oxidant dose, liquid/solid ratio, and soil granulometry) were first optimized in batch experiments. Obtained results revealed that increasing dose of H₂O₂ improved the oxidation efficiency while in Na₂S₂O₈ system, maximum HCHs were removed at 300 mM. However, oxidation efficiency was slightly improved by Fe^II-activation. Increasing the solid/liquid ratio decreased HCH removal in soil samples crushed to 500 μm while an opposite trend was observed for 2-mm samples. Dynamic column experiments showed that oxidation efficiency followed the order KMnO₄ > Na₂S₂O₈/Fe^II > Na₂S₂O₈ whatever the flow condition, whereas the removal extent declined at higher flow rate (e.g., ~50% by KMnO₄ at 0.5 mL/min as compared to ~30% at 2 mL/min). Both HCH removal and oxidant decomposition extents were found higher in saturated columns than the unsaturated ones. While no significant change in relative abundance of soil mineral constituents was observed before and after chemical oxidation, more than 60% of extractable organic matter was lost after chemical oxidation, thereby underscoring the non-selective behavior of chemical oxidation in soil. Due to the complexity of soil system, chemical oxidation has rarely been reported under flow through conditions, and therefore our findings will have promising implications in developing remediation techniques under dynamic conditions closer to field applications.     

The use of artificial neural network (ANN) for the prediction and simulation of oil degradation in wastewater by AOP

The application of advanced oxidation process (AOP) in the treatment of wastewater contaminated with oil was investigated in this study. The AOP investigated is the homogeneous photo-Fenton (UV/H₂O₂/Fe⁺²) process. The reaction is influenced by the input concentration of hydrogen peroxide H₂O₂, amount of the iron catalyst Fe⁺², pH, temperature, irradiation time, and concentration of oil in the wastewater. The removal efficiency for the used system at the optimal operational parameters (H₂O₂?=?400 mg/L, Fe⁺²?=?40 mg/L, pH?=?3, irradiation time?=?150 min, and temperature?=?30 °C) for 1,000 mg/L oil load was found to be 72 %. The study examined the implementation of artificial neural network (ANN) for the prediction and simulation of oil degradation in aqueous solution by photo-Fenton process. The multilayered feed-forward networks were trained by using a backpropagation algorithm; a three-layer network with 22 neurons in the hidden layer gave optimal results. The results show that the ANN model can predict the experimental results with high correlation coefficient (R ²?=?0.9949). The sensitivity analysis showed that all studied variables (H₂O₂, Fe⁺², pH, irradiation time, temperature, and oil concentration) have strong effect on the oil degradation. The pH was found to be the most influential parameter with relative importance of 20.6 %.     

Heterogeneous Fenton degradation of bisphenol A catalyzed by efficient adsorptive Fe3O4/GO nanocomposites

A new method for the degradation of bisphenol A (BPA) in aqueous solution was developed. The oxidative degradation characteristics of BPA in a heterogeneous Fenton reaction catalyzed by Fe₃O₄/graphite oxide (GO) were studied. Transmission electron microscopic images showed that the Fe₃O₄ nanoparticles were evenly distributed and were ～6 nm in diameter. Experimental results suggested that BPA conversion was affected by several factors, such as the loading amount of Fe₃O₄/GO, pH, and initial H₂O₂ concentration. In the system with 1.0 g L^?1 of Fe₃O₄/GO and 20 mmol L^?1 of H₂O₂, almost 90 % of BPA (20 mg L^?1) was degraded within 6 h at pH 6.0. Based on the degradation products identified by GC–MS, the degradation pathways of BPA were proposed. In addition, the reused catalyst Fe₃O₄/GO still retained its catalytic activity after three cycles, indicating that Fe₃O₄/GO had good stability and reusability. These results demonstrated that the heterogeneous Fenton reaction catalyzed by Fe₃O₄/GO is a promising advanced oxidation technology for the treatment of wastewater containing BPA.     

Accelerated photo-transformation of 2,2′,4,4′,5,5′-hexachlorobiphenyl (PCB 153) in water by dissolved organic matter

The ubiquitous dissolved organic matter (DOM) has an important influence on transformation of organic contaminants through the production of reactive substances, such as ^?OH, ¹O₂, and ³DOM*. The photolysis of a higher chlorinated polychlorinated biphenyl (PCB) congener (2,2′,4,4′,5,5′-hexachlorobiphenyl, PCB 153) under simulated sunlight in presence of humic acid (HA) was investigated. Degradation of PCB 153 was accelerated significantly by the addition of HA, with a rate constant of 0.0214, 0.0413, and 0.0358 h^?1 in the initial 18 h of irradiation in presence of 1, 5, and 20 mg/L HA, respectively. The main photodegradation products analyzed by gas chromatography mass spectrometry were 4-hydroxy-2,2′,4′,5,5′-pentaCB and 2,4,5-trichlorobenzoic acid. Main reactive species involved were determined by the electron spin-resonance spectroscopy, including ¹O₂ and ^?OH. Special scavengers were added to elucidate the photolysis mechanisms. By using the specific scavengers, it turned out that ^?OH accounted for 29.3 % of the degradation, and the intra-DOM reactive species (¹O₂, ^?OH, and ³DOM*) accounted for 59.6 % of the degradation. Photo-transformation sensitized by DOM, which involves both aqueous and intra-DOM reactions of PCBs with reactive species, may be one of the most important mechanisms for natural attenuation of PCBs.     

Environmentally friendly system for the degradation of multipesticide residues in aqueous media by the Fenton’s reaction

A Fenton oxidation system employing zero-valent iron (whose source was swarf, a residue of metallurgical industries, in powder form) and hydrogen peroxide for the treatment of an aqueous solution with six pesticides was developed, and the effect of the iron metal content, pH, and hydrogen peroxide concentration was evaluated. The characterization of the aqueous solution resulted in: pH 5.6, 105 mg L^?1 of dissolved organic carbon, and 44.6 NTU turbidity. In addition, the characterization of the swarf by FAAS and ICP-MS showed 98.43?±?7.40 % of zero-valent iron. The removal was strongly affected by the content of iron metal, pH, and hydrogen peroxide concentration. The best degradation conditions were 2.0 g swarf, pH 2.0, and 5 mmol L^?1 H₂O₂. At the end of the treatment, the pesticide degradation ranged from 60 to 100 %, leading to 55 % mineralization. Besides, all hydrogen peroxide was consumed and the determination of total dissolved iron resulted in 2 mg L^?1. Thus, the advantages of this system are rapid degradation (up to 20 min), high-degradation rates, simple handling, and low cost.

Application of Fenton, photo-Fenton, solar photo-Fenton, and UV/H2O2 to degradation of the antineoplastic agent mitoxantrone and toxicological evaluation

In the present study, selected advanced oxidation processes (AOPs)—namely, photo-Fenton (with Fe²⁺, Fe³⁺, and potassium ferrioxalate—FeOx—as iron sources), solar photo-Fenton, Fenton, and UV/H₂O₂—were investigated for degradation of the antineoplastic drug mitoxantrone (MTX), frequently used to treat metastatic breast cancer, skin cancer, and acute leukemia. The results showed that photo-Fenton processes employing Fe(III) and FeOx and the UV/H₂O₂ process were most efficient for mineralizing MTX, with 77, 82, and 90 % of total organic carbon removal, respectively. MTX probably forms a complex with Fe(III), as demonstrated by voltammetric and spectrophotometric measurements. Spectrophotometric titrations suggested that the complex has a 2:1 Fe³⁺:MTX stoichiometric ratio and a complexation constant (K) of 1.47 × 10⁴ M^–1, indicating high MTX affinity for Fe³⁺. Complexation partially inhibits the involvement of iron ions and hence the degradation of MTX during photo-Fenton. The UV/H₂O₂ process is usually slower than the photo-Fenton process, but, in this study, the UV/H₂O₂ process proved to be more efficient due to complexing of MTX with Fe(III). The drug exhibited no cytotoxicity against NIH/3T3 mouse embryonic fibroblast cells when oxidized by UV/H₂O₂ or by UV/H₂O₂/FeOx at the concentrations tested.     

Physiological and molecular responses of the earthworm <Emphasis Type="Italic">Eisenia fetida</Emphasis> to polychlorinated biphenyl contamination in soil

Polychlorinated biphenyls (PCBs) are a class of man-made organic compounds ubiquitously present in the biosphere. In this study, we evaluated the toxic effects of different concentrations of PCBs in two natural soils (i.e. red soil and fluvo-aquic soil) on the earthworm Eisenia fetida. The parameters investigated included anti-oxidative response, genotoxic potential, weight variation and biochemical responses of the earthworm exposed to two different types of soils spiked with PCBs after 7 or 14 days of exposure. Earthworms had significantly lower weights in both soils after PCB exposure. PCBs significantly increased catalase (CAT), superoxide dismutase (SOD), and guaiacol peroxidase (POD) activity in earthworms exposed to either soil type for 7 or 14 days and decreased the malondialdehyde (MDA) content in earthworms exposed to red soil for 14 days. Of the enzymes examined, SOD activity was the most sensitive to PCB stress. In addition, PCB exposure triggered dose-dependent coelomocyte DNA damage, even at the lowest concentration tested. This response was relatively stable between different soils. Three-way analysis of variance (ANOVA) showed that the weight variation, anti-oxidant enzyme activities, and MDA contents were significantly correlated with exposure concentration or exposure duration (P < 0.01). Furthermore, weight variation, CAT activity, and SOD activity were significantly affected by soil type (P < 0.01). Therefore, the soil type and exposure time influence the toxic effects of PCBs, and these factors should be considered when selecting responsive biomarkers.     

Biostimulation of the autochthonous microbial community for the depletion of polychlorinated biphenyls (PCBs) in contaminated sediments

In this study, the effect of the biostimulation of the autochthonous microbial community on the depletion of polychlorinated biphenyls (PCBs) in historically contaminated sediments (6.260?±?9.3 10^?3?μg PCB/ g dry weight) has been observed. Biostimulation consisted of (1) the amendment of an electron donor to favor the dehalogenation of the high-chlorinated PCBs and (2) the vegetation of sediments with Sparganium sp. plants to promote the oxidation of the low-chlorinated PCBs by rhizodegradation. The effects of the treatments have been analyzed in terms of both PCB depletion and changes of the autochthonous bacterial community structure. The relative abundance of selected bacterial groups with reference to untreated sediments has been evaluated by quantitative real-time PCR. The amendment of acetate determined the enrichment of anaerobic dechlorinators like Dehalococcoides sp. Vegetation with Sparganium sp. plants determined the enrichment of either (3) the dechlorinators, Dehalococcoides and the Chloroflexi o-17/DF-1 strains or (4) the Acidobacteria, β-Proteobacteria, Actinobacteria, α-Proteobacteria, Bacteroidetes, and Firmicutes. The combination of the two biostimulation strategy determined the 91.5 % of abatement of the initial PCB content.     

Fenton-like degradation of nalidixic acid with Fe3+/H2O2

The Fenton-like degradation of nalidixic acid was studied in this work. The effects of Fe³⁺ concentration and initial H₂O₂ concentration were investigated. Increasing the initial H₂O₂ concentration enhances the degradation and mineralization efficiency for nalidixic acid, while Fe³⁺ shows an optimal concentration of 0.25 mM. A complete removal of nalidixic acid and a TOC removal of 28 % were achieved in 60 min under a reaction condition of [Fe³⁺]?=?0.25 mM, [H₂O₂]?=?10 mM, T?=?35 °C, and pH?=?3. LC–MS analysis technique was used to analyze the possible degradation intermediates. The degradation pathways of nalidixic acid were proposed according to the identified intermediates and the electron density distribution of nalidixic acid. The Fenton-like degradation reaction of nalidixic acid mainly begins with the electrophilic attack of hydroxyl radical towards the C₃ position which results in the ring-opening reaction; meanwhile, hydroxyl radical attacking to the branched alkyl groups of nalidixic acid leads to the oxidation at the branched alkyl groups.     

Remediation of acid mine drainage (AMD)-contaminated soil by Phragmites australis and rhizosphere bacteria

Experiments were conducted to assess the impact of citric acid (CA) and rhizosphere bacteria on metal uptake in Phragmites australis cultured in a spiked acid mine drainage (AMD) soil. Rhizosphere iron-oxidizing bacteria (Fe(II)OB) enhanced the formation of Fe plaque on roots, which decreased the uptake of Fe and Mn. CA inhibited the growth of Fe(II)OB, decreased the formation of metal plaque, raised the metal mobility in soil, and increased the accumulation of metals in all tissues of the reeds. The higher the CA dosage, the more metals accumulated into reeds. The total amount of metals in reeds increased from 7.8?±?0.5?×?10^?6 mol plant^?1 (Mn), 1.4?±?0.1?×?10^?3 mol plant^?1 (Fe), and 1.0?±?0.1?×?10^?4 mol plant^?1 (Al) in spiked soil without CA to 22.2?±?0.5?×?10^?6 mol plant^?1 (Mn), 3.5?±?0.06?×?10^?3 mol plant^?1 (Fe), and 5.0?±?0.2?×?10^?4 mol plant^?1 (Al) in soil added with 33.616 g C₆H₈O₇·H₂O for per kilogram soil. CA could be effective at enhancing the phytoremediation of metals from AMD-contaminated soil.     

Kinetics of imidazolium-based ionic liquids degradation in aqueous solution by Fenton oxidation

In the last few years, several works dealing with Fenton oxidation of ionic liquids (ILs) have proved the capability of this technology for their degradation, achieving complete ILs removal and non-toxic effluents. Nevertheless, very little is known about the kinetics of this process, crucial for its potential application. In this work, the effect of several operating conditions, including reaction temperature (50–90 °C), catalyst load (10–50 mg L^?1 Fe³⁺), initial IL concentration (100–2000 mg L^?1), and hydrogen peroxide dose (10–200% of the stoichiometric amount for the complete IL mineralization) on 1-butyl-3-methylimidazolium chloride ([C₄mim]Cl) oxidation has been investigated. Under the optimum operating conditions (T = 90 °C; [Fe³⁺]₀ = 50 mg L^?1; [H₂O₂]₀ = 100% of the stoichiometric amount), the complete removal of [C₄mim]Cl (1000 mg L^?1) was achieved at 1.5-min reaction time. From the experimental results, a potential kinetic model capable to describe the removal of imidazolium-based ILs by Fenton oxidation has been developed. By fitting the proposed model to the experimental data, the orders of the reaction with respect to IL initial concentration, Fe³⁺ amount and H₂O₂ dose were found to be close to 1, with an apparent activation energy of 43.3 kJ mol^?1. The model resulted in a reasonable fit within the wide range of operating conditions tested in this work.     

Development of a new polyclonal antibody for the determination of polychlorinated biphenyls in indoor air by ic-ELISA

A new polyclonal antibody (pAb) was prepared and used for the determination of polychlorinated biphenyls (PCBs) in air samples to promote the application of immunoassay technology in the determination of PCBs. Three PCB congeners immunogen mixture was used to stimulate immune responses in rabbits. The specific pAb to PCBs was obtained and used to develop an indirect competitive enzyme-linked immunosorbent assay (ic-ELISA). A standard curve for Aroclor 1248 was prepared using concentrations ranging from 0.1 to 100 μg L^?1. The average IC₅₀ value was 16.21 μg L^?1 and the limit of detection at 10 % inhibition (IC₉₀) was 0.069 μg L^?1. The entire procedure was then evaluated using spiked air samples. The recoveries of Aroclor 1248 at various spiking levels in the air samples ranged from 84 to 113 %, with relative standard deviations of 3 to 6 %. Under optimum conditions, the cross-reactivity profiles of the assays were obtained using three selected congeners, four Aroclor products, and other structurally related compounds of PCBs. The assays were found to be highly specific for PCB congeners and Aroclors 1248 and 1242. The air samples were then analyzed using gas chromatography coupled with high-resolution mass spectrometry to confirm the ic-ELISA results. The attained results demonstrated that the proposed method was an effective and inexpensive technique for the PCBs determination in air samples.     

Degradation of bisphenol A in aqueous solution by persulfate activated with ferrous ion

Degradation of bisphenol A (BPA) in aqueous solution was studied with high-efficiency sulfate radical (SO₄ ^?·), which was generated by the activation of persulfate (S₂O₈ ^2?) with ferrous ion (Fe²⁺). S₂O₈ ^2? was activated by Fe²⁺ to produce SO₄ ^?·, and iron powder (Fe⁰) was used as a slow-releasing source of dissolved Fe²⁺. The major oxidation products of BPA were determined by liquid chromatography-mass spectrometer. The mineralization efficiency of BPA was monitored by total organic carbon (TOC) analyzer. BPA removal efficiency was improved by the increase of initial S₂O₈ ^2? or Fe²⁺ concentrations and then decreased with excess Fe²⁺ concentration. The adding mode of Fe²⁺ had significant impact on BPA degradation and mineralization. BPA removal rates increased from 49 to 97 % with sequential addition of Fe²⁺, while complete degradation was observed with continuous diffusion of Fe²⁺, and the latter achieved higher TOC removal rate. When Fe⁰ was employed as a slow-releasing source of dissolved Fe²⁺, 100 % of BPA degradation efficiency was achieved, and the highest removal rate of TOC (85 %) was obtained within 2 h. In the Fe⁰–S₂O₈ ^2? system, Fe⁰ as the activator of S₂O₈ ^2? could offer sustainable oxidation for BPA, and higher TOC removal rate was achieved. It was proved that Fe⁰–S₂O₈ ^2? system has perspective for future works.     

Study on the removal of elemental mercury from simulated flue gas by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-CeO<Subscript>2</Subscript>/AC at low temperature

Fe₂O₃ and CeO₂ modified activated coke (AC) synthesized by the equivalent-volume impregnation were employed to remove elemental mercury (Hg⁰) from simulated flue gas at a low temperature. Effects of the mass ratio of Fe₂O₃ and CeO₂, reaction temperature, and individual flue gas components including O₂, NO, SO₂, and H₂O (g) on Hg⁰ removal efficiency of impregnated AC were investigated. The samples were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Results showed that with optimal mass percentage of 3 % Fe₂O₃ and 3 % CeO₂ on Fe3Ce3/AC, the Hg⁰ removal efficiency could reach an average of 88.29 % at 110 °C. Besides, it was observed that O₂ and NO exhibited a promotional effect on Hg⁰ removal, H₂O (g) exerted a suppressive effect, and SO₂ showed an insignificant inhibition without O₂ to some extent. The analysis of XPS indicated that the main species of mercury on used Fe3Ce3/AC was HgO, which implied that adsorption and catalytic oxidation were both included in Hg⁰ removal. Furthermore, the lattice oxygen, chemisorbed oxygen, and/or weakly bonded oxygen species made a contribution to Hg⁰ oxidation.     

Degradation of 1,4-dioxane in water with heat- and Fe2+-activated persulfate oxidation

This research investigated the 1,4-dioxane (1,4-D) degradation efficiency and rate during persulfate oxidation at different temperatures, with and without Fe²⁺ addition, also considering the effect of pH and persulfate concentration on the oxidation of 1,4-D. Degradation pathways for 1,4-D have also been proposed based on the decomposition intermediates and by-products. The results indicate that 1,4-D was completely degraded with heat-activated persulfate oxidation within 3–80 h. The kinetics of the 1,4-D degradation process fitted well to a pseudo-first-order reaction model. Temperature was identified as the most important factor influencing the 1,4-D degradation rate during the oxidation process. As the temperature increased from 40 to 60 °C, the degradation rate improved significantly. At 40 °C, the addition of Fe²⁺ also increased the 1,4-D degradation rate. Interestingly, at 50 and 60 °C, the 1,4-D degradation rate decreased slightly with the addition of Fe²⁺. This reduced degradation rate may be attributed to the rapid conversion of Fe²⁺ to Fe³⁺ and the production of an Fe(OH)₃ precipitate which limited the ultimate oxidizing capability of persulfate with Fe²⁺ under higher temperatures. Higher persulfate concentrations led to higher 1,4-D degradation rates, but pH adjustment had no significant effect on the 1,4-D degradation rate. The identification of intermediates and by-products in the aqueous and gas phases showed that acetaldehyde, acetic acid, glycolaldehyde, glycolic acid, carbon dioxide, and hydrogen ion were generated during the persulfate oxidation process. A carbon balance analysis showed that 96 and 93 % of the carbon from the 1,4-D degradation were recovered as by-products with and without Fe²⁺ addition, respectively. Overall, persulfate oxidation of 1,4-D is promising as an economical and highly efficient technology for treatment of 1,4-D-contaminated water.     

TiO2 photocatalytic degradation of PCBs in soil-water systems containing fluoro surfactant

Titanium dioxide-mediated photodegradation of Polychlorinated biphenyls (PCBs) in soil/aqueous systems with added fluorinated surfactant was investigated. PCBs can bind tightly to organic matter in the soil, especially in aged, contaminated soil. Experiments showed an effective PCB photocatalytic degradation in mixed systems of soil/clay with anionic fluorinated surfactant FC-143 and TiO2. The FC-143 surfactant is stable in this photochemical process. PCB degradation rates in samples followed the order: spiked clay > spiked soil > Hudson River bank soil. The results suggest that anionic fluorinated surfactant may form semimicelles and/or admicelles on the surface of positively charged TiO2. The hydrophobic surface of TiO2 can provide a nonpolar phase that acts as a partioning medium for hydrophobic PCBs. Therefore, PCBs in soil can be released to the semimicelle and/or admicelle on the TiO2 surface and are effectively photodegraded in a dispersion containing anionic fluorinated surfactant. The combination of surfactant extraction and photooxidation forms the basis for a novel two-stage process for the removal and destruction of PCBs from soil.     

Distribution of potentially toxic elements (PTEs) in tailings,soils, and plants around Gol-E-Gohar iron mine,a case study in Iran

This study investigated the concentration of potentially toxic elements (PTEs) including Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sb, V, and Zn in 102 soils (in the Near and Far areas of the mine), 7 tailings, and 60 plant samples (shoots and roots of Artemisia sieberi and Zygophylum species) collected at the Gol-E-Gohar iron ore mine in Iran. The elemental concentrations in tailings and soil samples (in Near and Far areas) varied between 7.4 and 35.8 mg kg^?1 for As (with a mean of 25.39 mg kg^?1 for tailings), 7.9 and 261.5 mg kg^?1 (mean 189.83 mg kg^?1 for tailings) for Co, 17.7 and 885.03 mg kg^?1 (mean 472.77 mg kg^?1 for tailings) for Cu, 12,500 and 400,000 mg kg^?1 (mean 120,642.86 mg kg^?1 for tailings) for Fe, and 28.1 and 278.1 mg kg^?1 (mean 150.29 mg kg^?1 for tailings) for Ni. A number of physicochemical parameters and pollution index for soils were determined around the mine. Sequential extractions of tailings and soil samples indicated that Fe, Cr, and Co were the least mobile and that Mn, Zn, Cu, and As were potentially available for plants uptake. Similar to soil, the concentration of Al, As, Co, Cr, Cu, Fe, Mn, Mo, Ni, and Zn in plant samples decreased with the distance from the mining/processing areas. Data on plants showed that metal concentrations in shoots usually exceeded those in roots and varied significantly between the two investigated species (Artemisia sieberi > Zygophylum). All the reported results suggest that the soil and plants near the iron ore mine are contaminated with PTEs and that they can be potentially dispersed in the environment via aerosol transport and deposition.     

Zero-valent iron particles for PCB degradation and an evaluation of their effects on bacteria,plants, and soil organisms

Two types of nano-scale zero-valent iron (nZVI-B prepared by borohydride reduction and nZVI-T produced by thermal reduction of iron oxide nanoparticles in H₂) and a micro-scale ZVI (mZVI) were compared for PCB degradation efficiency in water and soil. In addition, the ecotoxicity of nZVI-B and nZVI-T particles in treated water and soil was evaluated on bacteria, plants, earthworms, and ostracods. All types of nZVI and mZVI were highly efficient in degradation of PCBs in water, but had little degradation effect on PCBs in soil. Although nZVI-B had a significant negative impact on the organisms tested, treatment with nZVI-T showed no negative effect, probably due to surface passivation through controlled oxidation of the nanoparticles.

     

Source characterization and risk of exposure to atmospheric polychlorinated biphenyls (PCBs) in Ghana

With recent evidence that persistent organic pollutants (POPs) such as polychlorinated biphenyls (PCBs) are emerging in environmental media in some developing countries that otherwise have sparing production and usage history, it has become important to identify such contemporary source factors of PCBs and the risks this may pose, in line with the global consensus on POP management and elimination. The present study investigated contaminations from atmospheric PCBs in Ghana, deciphered source factors, and accessed risk of exposure to dioxin-like PCBs (DL-PCBs). Atmospheric PCBs were monitored by deployment of PUF-disk passive air samplers (PAS) at several sites across Ghana for 56 days. Atmospheric ∑₁₉₀PCB concentration in Ghana ranged from 0.28 ng/m³ in Kumasi to 4.64 ng/m³ at Agbogbloshie, a suburb in Accra noted for informal electronic waste (e-waste) recycling activities. As high as 11.10 ng/m³ of PCB concentration was measured in plumes from uncontrolled open burning of e-wastes at Agbogbloshie. Applying statistical source characterization tools, it emerged that e-wastes were a major contributor to the environmental burden of atmospheric PCBs in Ghana. The risk of DL-PCB toxicity via inhalation in the Agbogbloshie area was 4.2 pg TEQ/day, within similar order of magnitude of an estimated risk of 3.85 pg TEQ/day faced by e-waste workers working averagely for 8 h per day. It is suggested that elimination of e-waste sites would help to significantly reduce PCB-related toxicity issues in Ghana.

Open image in new window

Graphical abstract ?