Assessing demineralization treatments for PVC effluent reuse in the resin polymerization step

To reduce fresh water consumption in a polyvinyl chloride (PVC) plant, the effluent from a biological treatment must be demineralized to be re-used in the resin polymerization process. Demineralization is a critical process, since the quality and the stability of the PVC resins are highly influenced by the water quality used in the process. The main target values for water parameters are the following: conductivity <10 μScm^?1, TOC < 10 mg L^?1, and Al < 0.1 mg L^?1. To achieve this quality, several reverse osmosis membranes from different materials and suppliers were tested and compared in the demineralization treatment. Polyamide membranes showed higher salt rejection compared to cellulose acetate membranes yielding both types similar flux and permeability. Two-pass reverse osmosis treatment was necessary to reach conductivities lower than 10 μS cm^?1. On the other hand, a good quality effluent for reuse was obtained by combining RO and ionic exchange resins. Results showed that good quality PVC resins in terms of color, granulometry, porosity, and bulk density were obtained when demineralized water from two-pass reverse osmosis was used as fresh water, proving the feasibility of the effluent reuse in the PVC industry.     

Determination of phenols and pharmaceuticals in municipal wastewaters from Polish treatment plants by ultrasound-assisted emulsification–microextraction followed by GC–MS

A method combining ultrasound-assisted emulsification–microextraction (USAEME) with gas chromatography–mass spectrometry (GC–MS) was developed for simultaneous determination of four acidic pharmaceuticals, ibuprofen, naproxen, ketoprofen, and diclofenac, as well as four phenols, 4-octylphenol, 4-n-nonylphenol, bisphenol A, and triclosan in municipal wastewaters. Conditions of extraction and simultaneous derivatization were optimized with respect to such aspects as type and volume of extraction solvent, volume of derivatization reagent, kind and amount of buffering salt, location of the test tube in the ultrasonic bath, and extraction time. The average correlation coefficient of the calibration curves was 0.9946. The LOD/(LOQ) values in influent and effluent wastewater were in the range of 0.002–0.121/(0.005–0.403) μg L^?1 and 0.002–0.828/(0.006–2.758) μg L^?1, respectively. Quantitative recoveries (≥94 %) and satisfactory precision (average RSD 8.2 %) were obtained. The optimized USAEME/GC–MS method was applied for determination of the considered pharmaceuticals and phenols in influents and treated effluents from nine Polish municipal wastewater treatment plants. The average concentration of acidic pharmaceuticals in influent and effluent wastewater were in the range of 0.06–551.96 μg L^?1 and 0.01–22.61 μg L^?1, respectively, while for phenols were in the range of 0.03–102.54 μg L^?1 and 0.02–10.84 μg L^?1, respectively. The removal efficiencies of the target compounds during purification process were between 84 and 99 %.     

Evaluation of growth and biochemical indicators of Salvinia natans exposed to zinc oxide nanoparticles and zinc accumulation in plants

The adverse effects of zinc oxide nanoparticles (ZnO NPs) with an average diameter of 25 nm on the aquatic plant Salvinia natans (L.) All. were determined. Growth, superoxide dismutase (SOD) activity, catalase (CAT) activity, peroxidase activity, and chlorophyll content of the plants were measured after 7 days of exposure to different concentrations of ZnO NPs (1 to 50 mg L^?1). The particle distribution in the culture medium (without plants) during the first 24 h was determined using a Nanotrac 250 particle analyzer. We also investigated the zinc accumulation in leaves and roots of the plant after 7 days of exposure. Exposure to 50 mg L^?1 ZnO NPs significantly increased SOD and CAT activities (P?<?0.05) and significantly depressed photosynthetic pigments (P?<?0.05). However, plant growth was not significantly affected (P?>?0.05). NPs completely precipitated at the bottom of the container at 8 h except for the portions of dissolution and aggregation on the roots. ZnO NPs at a concentration of 50 mg L^?1 can adversely affect S. natans, and their stress is affected by their aggregation and dissolution.     

Evaluation of Acinetobacter sp. B9 for Cr (VI) resistance and detoxification with potential application in bioremediation of heavy-metals-rich industrial wastewater

Present work demonstrates Cr (VI) detoxification and resistance mechanism of a newly isolated strain (B9) of Acinetobacter sp. Bioremediation potential of the strain B9 is shown by simultaneous removal of major heavy metals including chromium from heavy-metals-rich metal finishing industrial wastewater. Strain B9 tolerate up to 350 mg L^?1 of Cr (VI) and also shows level of tolerance to Ni (II), Zn (II), Pb (II), and Cd (II). The strain was capable of reducing 67 % of initial 7.0 mg L^?1 of Cr (VI) within 24 h of incubation, while in presence of Cu ions 100 % removal of initial 7.0 and 10 mg L^?1 of Cr (VI) was observed with in 24 h. pH in the range of 6.0–8.0 and inoculum size of 2 % (v/v) were determined to be optimum for dichromate reduction. Fourier transform infrared spectroscopy and transmission electron microscopy studies suggested absorption or intracellular accumulation and that might be one of the major mechanisms behind the chromium resistance by strain B9. Scanning electron microscopy showed morphological changes in the strain due to chromium stress. Relevance of the strain for treatment of heavy-metals-rich industrial wastewater resulted in 93.7, 55.4, and 68.94 % removal of initial 30 mg L^?1 Cr (VI), 246 mg L^?1 total Cr, and 51 mg L^?1 Ni, respectively, after 144 h of treatment in a batch mode.     

Phosphorus removal in a sulfur–limestone autotrophic denitrification (SLAD) biofilter

The sulfur–limestone autotrophic denitrification (SLAD) biofilter was able to remove phosphorous from wastewater during autotrophic denitrification. Parameters influencing autotrophic denitrification in the SLAD biofilter, such as hydraulic retention time (HRT), influent nitrate (NO₃ ^?), and influent PO₄ ^3? concentrations, had significant effects on P removal. P removal was well correlated with total oxidized nitrogen (TON) removed in the SLAD biofilter; the more TON removed, the more efficient P removal was achieved. When treating the synthetic wastewater containing NO₃ ^?-N of 30 mg L^?1 and PO₄ ^3?-P of 15 mg L^?1, the SLAD biofilter removed phosphorus of 45 % when the HRT was 6 h, in addition with TN removal of nearly 100 %. The optimal phosphorus removal in the SLAD biofilter was around 60 %. For the synthetic wastewater containing a PO₄ ^3?-P concentration of 15 mg L^?1, the main mechanism of phosphorus removal was the formation of calcium phosphate precipitates.     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Effects of silicon and copper on bamboo grown hydroponically

Due to its high growth rate and biomass production, bamboo has recently been proven to be useful in wastewater treatment. Bamboo accumulates high silicon (Si) levels in its tissues, which may improve its development and tolerance to metal toxicity. This study investigates the effect of Si supplementation on bamboo growth and copper (Cu) sensitivity. An 8-month hydroponic culture of bamboo Gigantocloa sp. “Malay Dwarf ” was performed. The bamboo plants were first submitted to a range of Si supplementation (0–1.5 mM). After 6 months, a potentially toxic Cu concentration of 1.5 μM Cu²⁺ was added. Contrary to many studies on other plants, bamboo growth did not depend on Si levels even though it absorbed Si up to 218 mg g^?1 in leaves. The absorption of Cu by bamboo plants was not altered by the Si supplementation; Cu accumulated mainly in roots (131 mg kg^?1), but was also found in leaves (16.6 mg kg^?1) and stems (9.8 mg kg^?1). Copper addition did not induce any toxicity symptoms. The different Cu and Si absorption mechanisms may partially explain why Si did not influence Cu repartition and concentration in bamboo. Given the high biomass and its absorption capacity, bamboo could potentially tolerate and accumulate high Cu concentrations making this plant useful for wastewater treatment.     

Performance of full-scale coagulation-flocculation/DAF as a pre-treatment technology for biodegradability enhancement of high strength wastepaper-recycling wastewater

Paper mill wastewater leads to a serious damage on the environment owing to the high content of organic matters, suspended solids, toxic substances, and lignin. Hence, exploring new treatment technologies is the passion of environmental engineers to minimize the effluent impact on the environment and cleaner production aspects. This research focused on the performance of full-scale coagulation-fluctuation/DAF system for pre-treatment of high strength wastepaper-recycling wastewater and its effect on biodegradability improvement. To optimize unit performance, optimum coagulant and flocculant doses were firstly determined by jar test without prior change and adjustment of pH in lab-scale experiments. The optimum dosages were obtained by 1500 mg L^?1 polyaluminum chloride (PACl) as coagulant coupled with 40 mg L^?1 cationic polyacrylamide (C-PAM) as flocculant. Percentage removals of 39?±?10, 6.8?±?3.6, 31.0?±?6.7, 24.0?±?3.8, and 33.0?±?20.0 were achieved for COD, sCOD, BOD₅, sBOD₅, and color, respectively. The average BOD₅ to COD ratio after pre-treatment increased from 0.44 to 0.5, whereas the ratio of sBOD₅/sCOD dropped from 0.65 to 0.53. A superior effectiveness in reduction of TSS (98.1%) and VSS (98.4%) was also achieved. The results show that the application process is able to prevent malfunction operation in the following bioreactors which is obtainable through bio-treatability enhancement of pre-treated wastewater and reducing the risks of clogging and sludge washout. Attached growth processes are suggested to be applied in the further anaerobic/aerobic processes because of high proportion of soluble fraction of COD in the effluent to avoid poor floc formation and dispersed growth problems.     

Effects of bisphenol A on ammonium assimilation in soybean roots

Bisphenol A (BPA), which is ubiquitous in the environment, is an example of an endocrine-disrupting compound (EDC). Ammonium assimilation has an important function in plant growth and development. However, insufficient information on the potential effect of BPA on ammonium assimilation in plants is available. In this study, the effects of BPA on ammonium assimilation in roots of soybean seedlings were investigated. During the stress period, 1.5 mg L^?1 of BPA improved glutamine synthetase (GS)/glutamate synthase (GOGAT) cycle and glutamate dehydrogenase (GDH) pathway in ammonium assimilation. The amino acid and the soluble protein contents increased in the soybeans. At 17.2 and 50.0 mg L^?1 of BPA, the GS/GOGAT cycle was inhibited and the GDH pathway was promoted. The amino acid content increased and the soluble protein content decreased. During the recovery period, the GS/GOGAT cycle and the GDH pathway recovered at 1.5 and 17.2 mg L^?1 of BPA but not at 50.0 mg L^?1 of BPA. The amino acid content continuously increased and the soluble protein content decreased compared with those in the control treatment. In summary, BPA treatment could affect the contents of soluble protein and amino acid in the soybean roots by regulating ammonium assimilation.     

Bioelectrochemical anaerobic sewage treatment technology for Arctic communities

This study describes a novel wastewater treatment technology suitable for small remote northern communities. The technology is based on an enhanced biodegradation of organic carbon through a combination of anaerobic methanogenic and microbial electrochemical (bioelectrochemical) degradation processes leading to biomethane production. The microbial electrochemical degradation is achieved in a membraneless flow-through bioanode–biocathode setup operating at an applied voltage below the water electrolysis threshold. Laboratory wastewater treatment tests conducted through a broad range of mesophilic and psychrophilic temperatures (5–23 °C) using synthetic wastewater showed a biochemical oxygen demand (BOD₅) removal efficiency of 90–97% and an effluent BOD₅ concentration as low as 7 mg L^?1. An electricity consumption of 0.6 kWh kg^?1 of chemical oxygen demand (COD) removed was observed. Low energy consumption coupled with enhanced methane production led to a net positive energy balance in the bioelectrochemical treatment system.     

Cadmium-tolerant bacteria induce metal stress tolerance in cereals

Cadmium usually hampers plant growth, but bacterial inoculation may improve stress tolerance in plants to Cd by involving various mechanisms. The objective was to characterize and identify bacteria that improve plant growth under Cd stress and reduce Cd uptake. Cadmium-tolerant bacteria were isolated from rhizosphere soil, which was irrigated with tannery effluent, and six strains were selected as highly tolerant to Cd, showing minimum inhibitory concentration as 500 mg L^?1 or 4.45 mmol L^?1. These strains were identified by 16S rRNA gene analysis and functional analysis in regard to plant growth promotion characteristics. To determine their effect on cereal growth under Cd stress, seeds were inoculated with these strains individually and grown in soil contaminated with three Cd levels (0, 40 and 80 mg kg^?1). Biomass production, relative water content (RWC), electrolyte leakage (ELL) and tissue Cd concentration were measured. Biomass of both cereals was inhibited strongly when exposed to Cd; however, bacterial inoculation significantly reduced the suppressive effect of Cd on cereal growth and physiology. The bacterial isolates belonged to the genera Klebsiella, Stenotrophomonas, Bacillus and Serratia. Maize was more sensitive than wheat to Cd. Klebsiella sp. strain CIK-502 had the most pronounced effects in promoting maize and wheat growth and lowering Cd uptake under Cd stress.     

Arsenic toxicity in garden cress (Lepidium sativum Linn.): significance of potassium nutrition

In a hydroponic culture, experiments were performed to study the influence of potassium (K) supplementation (0, 20, 40, 60, 80, and 100 mg L^?1) on the arsenic (As; 0, 8, and 10 mg L^?1)-accrued changes in growth traits (plant biomass, root–shoot length) and the contents of lepidine, As and K, in garden cress (Lepidium sativum Linn.) at 10 days after treatment. The changes in these traits were correlated with shoot proline content, protein profile, and the activities of antioxidant enzymes namely superoxide dismutase (SOD, EC 1.15.1.1), catalase (CAT, EC 1.11.1.6), glutathione reductase (GR, EC 1.8.1.7), and ascorbate peroxidase (APX, EC 1.11.1.11). In general, As-alone treatments significantly decreased the growth traits but lead to significant enhancements in shoot proline and enzyme activities. K-supplementation to As-treated L. sativum seedlings decreased shoot-As content, reduced As-induced decreases in growth traits but enhanced the content of shoot proline, and the activities of the studied enzymes maximally with K₁₀₀ + As₈ and As₁₀ mg L^?1. Both 8 and 10 mg L^?1 of As drastically downregulated the shoot proteins ranging from 43–65 kDa. With As₁₀ mg L^?1, there was a total depletion of protein bands below 23 kDa; however, K₈₀ mg L^?1 maximally recovered and upregulated the protein bands. Additionally, protein bands were downregulated (at par with As-alone treatment) above K₈₀ mg L^?1 level. Interestingly, As-stress increased lepidine content in a dose-dependent manner which was further augmented with the K-supplementation. It is suggested that K protects L. sativum against As-toxicity by decreasing its accumulation and strengthening antioxidant defense system and protein stability.     

Effect of exogenous abscisic acid on the level of antioxidants in Atractylodes macrocephala Koidz under lead stress

This study hypothesized that the positive or negative effects of exogenous abscisic acid (ABA) on oxidative stress caused by lead were dose dependent. The effects of different levels of ABA (2.5, 5, and 10 mg L^?1) on lead toxicity in the leaves of Atractylodes macrocephala were studied by investigating plant growth, soluble sugars, proteins, lipid peroxidation, and antioxidative enzymes. Excess Pb inhibited root dry weight, root length, and the number of lateral roots, but increased shoot growth. In addition, lead stress significantly decreased the levels of chlorophyll pigments, protein, and activities of superoxide dismutase (SOD), catalase (CAT), ascorbate peroxidase (APX), and peroxidase (POD). Different levels of ABA significantly increased SOD, CAT, POD, and APX activities, but decreased the level of hydrogen peroxide and malondialdehyde in nonstressed plants. Exogenous application of 2.5 mg L^?1 ABA detoxified the stress-generated damages caused by Pb and also enhanced plant growth, soluble sugars, proteins, and all four antioxidant enzyme activities but reduced Pb uptake of lead-stressed plant compared to lead treatment alone. However, the toxic effects of Pb were further increased by the applications of 5 and 10 mg L^?1 ABA. The levels of antioxidants caused by a low concentration of exogenous ABA might be responsible for minimizing the Pb-induced toxicity in A. macrocephala.     

Phytoaccumulation potentials of two biotechnologically propagated ecotypes of Arundo donax in copper-contaminated synthetic wastewater

An in vitro experiment was carried out to evaluate the phytoremediation potentials of two somatic embryo-derived ecotypes of Arundo donax—BL (American ecotype) and 20SZ (Hungarian ecotype)—of copper from synthetic wastewater. The two ecotypes were grown under sterile conditions in tubes containing a nutrient solution supplied with increasing doses of Cu (0, 1, 2, 3, 5, 10, and 26.8 mg L^?1) for 6 weeks. The translocation and bioaccumulation factors and removal rate were estimated. In general, increasing Cu concentration in nutrient solution slightly decreased root, stem and leaf biomass without toxicity symptoms up to 26.8 mg L^?1. Moreover, both ecotypes showed high Cu removal efficiency from aqueous solution. However, Cu removal rate ranged between 96.6 to 98.8 % for BL ecotype and 97 to 100 % for 20SZ ecotype. Data illustrated that both BL and 20SZ ecotypes may be employed to treat Cu-contaminated water bodies up to 26.8 mg L^?1.     

Stormwater harvesting from landscaped areas: effect of herbicide application on water quality and usage

The suitability of stormwater harvested from pervious pavement system (PPS) structures for reuse purposes was investigated in conditions where glyphosate-containing herbicides (GCH) are applied as part of PPS maintenance procedure. The experiment was based on the four-layered design previously described as detailed in CIRIA C582. Results indicated that the highest sodium absorption ratio (SAR) of 1.6 recorded in this study, was less than that at which loss of permeability begins to occur as well as deterioration of matrix structure. Furthermore, the maximum electrical conductivity (ECw) of 2990 μS cm^?1, recorded for 7200 mg L^?1 concentration (GCH) was slightly below the unstable classification range at which salinity problems related to water quality occur such that salts accumulate in the root zone to the extent that crop yields are adversely affected. However, GCH concentration of 720 mg L^?1 was within ‘permissible’ range while that of 72 mg L^?1 was within ‘excellent’ range. Current study raises some environmental concerns owing to the overall impact that GCH at concentrations above 72 mg L^?1 exerts on the net performance of the organic decomposers, heavy metal and hydrocarbon release from the system and thus, should be further investigated. However, effluent from all the test models including those dosed with high GCH concentration of 7200 mg L^?1 do not pose any threat in terms of infiltration or deterioration associated with salinity although, there are indications that high dosage of the herbicide could lead to an elevated electrical conductivity of the recycled water.

Open image in new window

Graphical abstract Impact of herbicide on irrigation water quality

     

Reduction of Greenhouse Gases from Anaerobic Piggery Wastewater Treatment by Bromochloromethane in Taiwan

Abstract

This work establishes methods of reducing the amount of methane produced from the anaerobic treatment of piggery wastewater by either reducing the storage time before solid/liquid separation or inhibiting the activity of methanogens in anaerobic wastewater treatment system. Experimental results showed these two methods can be adopted effectively to reduce methane production resulting from anaerobic piggery wastewater treatment. First, the wastewater must be processed using solid/liquid separation immediately after washing pig houses. This process can reduce by 62% the biogas production and indirectly decrease the methane production from the anaerobic wastewater treatment reactor. Second, adding 10 mg L^?1 bromochloromethane (BCM) daily into the anaerobic wastewater treatment reactor can significantly reduce the amount of biogas and methane produced during the anaerobic fermentation process. Furthermore, biogas production can be completely inhibited after 4 days. Adding BCM (≤10 mg L^?1) to wastewater only slightly affected the efficiency of the anaerobic wastewater treatment process. Results in this study can provide the basis for further research on reduction of the amount of methane produced from anaerobic wastewater treatments.     

Distribution of potentially toxic elements (PTEs) in tailings,soils, and plants around Gol-E-Gohar iron mine,a case study in Iran

This study investigated the concentration of potentially toxic elements (PTEs) including Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sb, V, and Zn in 102 soils (in the Near and Far areas of the mine), 7 tailings, and 60 plant samples (shoots and roots of Artemisia sieberi and Zygophylum species) collected at the Gol-E-Gohar iron ore mine in Iran. The elemental concentrations in tailings and soil samples (in Near and Far areas) varied between 7.4 and 35.8 mg kg^?1 for As (with a mean of 25.39 mg kg^?1 for tailings), 7.9 and 261.5 mg kg^?1 (mean 189.83 mg kg^?1 for tailings) for Co, 17.7 and 885.03 mg kg^?1 (mean 472.77 mg kg^?1 for tailings) for Cu, 12,500 and 400,000 mg kg^?1 (mean 120,642.86 mg kg^?1 for tailings) for Fe, and 28.1 and 278.1 mg kg^?1 (mean 150.29 mg kg^?1 for tailings) for Ni. A number of physicochemical parameters and pollution index for soils were determined around the mine. Sequential extractions of tailings and soil samples indicated that Fe, Cr, and Co were the least mobile and that Mn, Zn, Cu, and As were potentially available for plants uptake. Similar to soil, the concentration of Al, As, Co, Cr, Cu, Fe, Mn, Mo, Ni, and Zn in plant samples decreased with the distance from the mining/processing areas. Data on plants showed that metal concentrations in shoots usually exceeded those in roots and varied significantly between the two investigated species (Artemisia sieberi > Zygophylum). All the reported results suggest that the soil and plants near the iron ore mine are contaminated with PTEs and that they can be potentially dispersed in the environment via aerosol transport and deposition.     

Influence of exogenous urea on photosynthetic pigments, 14CO2 uptake, and urease activity in Elodea densa—environmental implications

This paper analyzes the effect of exogenous urea in increased concentration gradient (0, 100, 500 and 1,000 mg L^?1) on photosynthetic pigments (measured spectrophotometrically), uptake of ¹⁴CO₂ (using radioisotope), and urease activity (by measuring ammonia with Nessler’s reagent) in leaves of Elodea densa Planch. We have observed that low concentration of urea (100 mg L^?1) stimulates the accumulation of photosynthetic pigments and intensifies photosynthesis in E. densa, whereas high concentration (1,000 mg L^?1) suppresses these processes. Urease activity increased by approximately 2.7 and 8 fold when exogenous urea concentrations were 100 and 500 mg L^?1, respectively. However, exogenous urea in high concentration (1,000 mg L^?1) decreased urease activity by 1.5 fold compared to the control. The necessity of mitigating urea and other nitrogen-containing compounds (NH₃ from urea) in water bodies has been discussed with emphasis on the potential for phytoremediation of urea using common water weed viz. E. densa.     

Occurrence and risk assessment of antidepressants in Huangpu River of Shanghai,China

Antidepressants are gaining public attention because of increasing reports of their occurrence in environment and their potential impact on ecosystems and human health. Continuous input of pharmaceuticals into rivers, through psychiatric hospital or wastewater treatment plant (WWTPs) effluent, may cause adverse effects on the aquatic ecosystems of the receiving water bodies. This work investigates the occurrence and sources of 8 antidepressants in main stream and tributaries of Huangpu River in Shanghai. The detected concentrations of the selected antidepressants ranged from low nanogram per liter to 42.9 ng L^?1 (fluoxetine) in main stream and ranged from low nanogram per liter to 33.7 ng L^?1 (fluoxetine) in tributaries. To study the effect of hospital or wastewater treatment plants (WWTPs) on environment, the upstream and downstream samples were analyzed. Generally, antidepressants had greater concentrations in downstream than that in upstream of the WWTPs or hospitals. It is suggesting that WWTPs and hospitals may introduce pollution into water environment. A preliminary risk assessment was conducted: none of the eight target compounds yielded risk quotient (RQ) values more than 0.1, thus indicating that no adverse effect is expected in water environment. These results will provide background data for future antidepressants pollution control and management in Shanghai, China.     

Assessment of the effluent quality from a gold mining industry in Ghana

The physical and chemical qualities of the process effluent and the tailings dam wastewater of AngloGold-Ashanti Limited, a gold mining company in Ghana, were studied from June to September, 2010. The process effluent from the gold extraction plant contains high amounts of suspended solids and is therefore highly turbid. Arsenic, copper and cyanide were identified as the major pollutants in the process effluent with average concentrations of 10.0, 3.1 and 21.6 mg?L^?1, respectively. Arsenic, copper, iron and free cyanide (CN^?) concentrations in the process effluent exceeded the Ghana EPA discharge limits; therefore, it is necessary to treat the process effluent before it can be discharged into the environment. Principal component analysis of the data indicated that the process effluent characteristics were influenced by the gold extraction process as well as the nature of the gold-bearing ore processed. No significant correlation was observed between the wastewater characteristics themselves, except for the dissolved oxygen and the biochemical oxygen demand. The process effluent is fed to the Sansu tailings dam, which removes 99.9 % of the total suspended solids and 99.7 % of the turbidity; but copper, arsenic and cyanide concentrations were still high. The effluent produced can be classified as inorganic with a high load of non-biodegradable compounds. It was noted that, though the Sansu tailings dam stores the polluted effluent from the gold extraction plant, there will still be serious environmental problems in the event of failure of the dam.