凹凸棒土/苯胺-邻氨基酚复合吸附剂的制备及其对Cr(Ⅵ)的吸附性能

采用原位聚合法制备了凹凸棒土/苯胺-邻氨基酚（ATP/PANOAP）复合吸附剂,对其进行了SEM和FTIR表征,并通过吸附实验考察了ATP/PANOAP对水中Cr（Ⅵ）的吸附性能。实验结果表明,ATP/PANOAP对水中Cr（Ⅵ）具有良好的去除效果,在Cr（Ⅵ）初始质量浓度为50 mg/L、溶液pH为6、吸附剂加入量为0.375 g/L、温度为298 K的条件下,Cr（Ⅵ）去除率达93.39%。ATP/PANOAP对Cr（Ⅵ）的吸附动力学过程符合准二级动力学模型,吸附热力学过程符合Langmuir单层吸附模型,该吸附过程以化学吸附为主,且为自发进行的吸热反应。     

交联壳聚糖/沸石复合吸附剂的制备及性能

用沸石负载由缩水甘油基三乙基氯化铵交联的壳聚糖，制得了性能良好的交联壳聚糖/沸石复合吸附剂。研究了该吸附剂应用性能的影响因素，探讨了该吸附剂的吸附性、沉降性和重复使用性，利用FTIR仪和高倍透射电子显微镜对该吸附剂的结构进行了表征。实验结果表明:壳聚糖的交联度为0.93、交联壳聚糖与沸石的质量比为0.045时，制得的交联壳聚糖/沸石复合吸附剂对腐殖酸的去除率可达81.4%，吸附量为4.07mg/g;交联壳聚糖/沸石复合吸附剂对腐殖酸的吸附性能较沸石有显著提高，沉降时间较交联壳聚糖明显缩短;经二次洗脱后腐殖酸去除率仍可达80.2%，腐殖酸吸附量为4.01mg/g。     

改性核桃壳对Cr(Ⅵ)的吸附

采用甲醛-硫酸改性法制备改性核桃壳吸附剂,利用静态吸附法研究了改性核桃壳对模拟废水中低浓度Cr(Ⅵ)的吸附性能,并采用SEM和FTIR技术对改性前后的核桃壳进行表征。表征结果显示,改性后的核桃壳表面更粗糙,孔隙轮廓更清晰,更有利于对Cr(Ⅵ)的吸附。实验结果表明:在初始Cr(Ⅵ)质量浓度为20 mg/L、初始废水p H为1、吸附温度为30℃、吸附时间为100 min、改性核桃壳加入量为24 g/L的条件下,改性核桃壳对Cr(Ⅵ)的去除率为98.4%,高于在相同条件下未改性核桃壳对Cr(Ⅵ)的去除率(93.1%);改性核桃壳对Cr(Ⅵ)的吸附更符合Freundlich等温吸附方程,对Cr(Ⅵ)的吸附行为满足拟二级动力学方程。     

交联壳聚糖季铵盐吸附剂的制备及其对重金属离子的吸附

以壳聚糖为原料、二甲基二烯丙基氯化铵（DMDAAC）为接枝单体、甲醛为预交联剂、环氧氯丙烷为交联剂，通过反相乳液聚合制备出交联壳聚糖季铵盐吸附剂，并将其用于吸附Ni（Ⅱ）和Cr（Ⅵ）。考察了吸附时间、溶液初始浓度、溶液pH等因素对吸附效果的影响。实验结果表明：该吸附剂对Ni（Ⅱ）和Cr（Ⅵ）的吸附过程遵循拟二级动力学方程，吸附等温线符合Langmuir方程；在30 ℃条件下，Ni（Ⅱ）和Cr（Ⅵ）的溶液初始浓度均为1 mmol/L时，该吸附剂吸附Ni（Ⅱ）和Cr（Ⅵ）的最佳溶液pH分别为7和6，对应的平衡吸附量分别为1.18，1.99 mmol/g；该吸附剂可用盐酸再生，重复使用性能良好。     

Optimizing Cr(VI) adsorption on activated carbon produced from heavy oil fly ash

In order to explore the beneficial utilization of heavy oil fly ash (HOFA) generated in the power plants, the present study is intended to optimize the chromium(VI) [Cr(VI)] adsorption on activated carbon produced from HOFA. The raw HOFA obtained from a power plant was washed by nitric/hydrochloric acid and activated at 800 °C with a holding time of 60 min to produce fly ash activated carbon (FAC). Phosphoric acid was used as a chemical agent to improve the surface characteristics of the HOFA during the activation process. Batch adsorption experiments were employed to evaluate the effects of different parameters such as initial Cr(VI) concentration, pH, and FAC dose on the removal of Cr(VI) from aqueous solution. A total of 17 adsorption experimental runs were carried out employing the detailed conditions followed the response surface methodology based on the Box–Behnken design. The results indicate that developed FAC has the potential for removing Cr(VI) from wastewater. Under the test conditions, a maximum of 91.51 % Cr(VI) removal efficiency was achieved.     

西瓜皮基碳气凝胶的制备及其吸附性能

以西瓜皮为碳源,通过水热处理结合冷冻干燥法制备了碳气凝胶。采用FTIR、拉曼光谱、XPS和SEM等技术对碳气凝胶的表面基团、形貌和结构进行了表征。考察了碳气凝胶对罗丹明B和孔雀石绿模拟染料废水的吸附性能。表征结果显示,碳气凝胶呈现典型的三维无序网状多孔结构,其表面存在大量的羟基、羰基、羧基等官能团。实验结果表明,在罗丹明B或孔雀石绿初始质量浓度为10 mg/L、碳气凝胶加入量为0.5 g/L、吸附温度为常温、初始废水p H为染料废水自然酸碱度、吸附时间为1 h的条件下,碳气凝胶对孔雀石绿的去除率为92.7%,对罗丹明B的去除率为67.2%;循环使用4次到6次,罗丹明B和孔雀石绿的去除率略有降低。     

Fe_3O_4@SiO_2复合气凝胶的制备及其对刚果红的吸附

以Fe Cl_3·6H_2O和正硅酸四乙酯为原料,通过溶胶-凝胶法结合醇溶剂热法制备了Fe_3O_4@Si O_2复合气凝胶。采用XRD,FTIR,SEM,EDS等技术对Fe_3O_4@Si O_2的结构进行了表征。考察了Fe_3O_4@Si O_2对刚果红溶液的吸附性能。表征结果显示,Fe_3O_4@Si O_2复合气凝胶是由直径为10~20 nm的近球形颗粒组装而成的具有三维网络结构的纳米材料,比表面积为457.93 m~2/g,平均孔径为10.7 nm。在溶液p H为5、吸附时间为35 min的最佳工艺条件下,采用Fe_3O_4@Si O_2吸附处理质量浓度为10 mg/L的刚果红溶液,刚果红去除率为99.39%,此时溶液中刚果红的质量浓度仅为0.052 mg/L。Fe_3O_4@Si O_2复合气凝胶吸附刚果红后具有较好的解吸和再生能力。     

Synergistic Effects of Multiple Metal Contaminants on Electrokinetic Remediation of Soils

This article presents a bench‐scale study performed to investigate the removal of heavy metals when they exist individually and in combination in soils. Electrokinetic experiments were conducted using two types of clayey soils, kaolin and glacial till. These soils were contaminated with Cr(VI) only, with Ni(II) only, and with Cr(VI), Ni(II), and Cd(II) combined. It was found that in kaolin, a significant pH variation occurred due to electric potential application, affecting the adsorption‐desorption and dissolution‐precipitation, as well as the extent of migration of the contaminants. In glacial till, however, pH changes were not affected significantly. In both kaolin and glacial till, the migration of Cr(VI) and Ni(II) was higher when they were present individually compared to when they existed together with Cd(II). Cr(VI) migration as single or combined contaminant was lower in kaolin as compared to that in glacial till. This result was due to the low pH conditions created near the anode region in kaolin that led to high Cr(VI) adsorption to the clay surfaces. In glacial till, however, nickel precipitated with or without the presence of co‐contaminants due to high pH conditions in the soil. Overall, this study demonstrates that adsorption, precipitation, and reduction are the significant hindering mechanisms for the removal of heavy metals using electrokinetic remediation. The direction of the contaminant migration and overall removal efficiency depend on the polarity of the contaminant, the presence of co‐contaminants, and the type of soil. © 2001 John Wiley & Sons.     

Preparation and Properties of a Chitosan–Hyaluronic Acid-Polypyrrole Conductive Hydrogel Catalyzed by Laccase

Electro conductive hydrogels, consisting of chitosan (CS), hyaluronic acid (HA), and polypyrrole (PPy), were prepared via an in situ enzymic polymerization of pyrrole in the CS–HA hydrogel, using laccase as the catalyst. This CS–HA–PPy composite hydrogel showed good conductivity. The chemical structure and morphology of this conductive hydrogel were studied by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction technique. For CS–HA–PPy and CH–HA hydrogel, the temperature at which fastest decomposition occurred was 260 and 244 °C, respectively. That means the thermal stability of CS–HA–PPy is better than CS–HA hydrogel. The conductive hydrogel also showed excellent swelling and deswelling behaviors.     

氨基改性二氧化硅气凝胶的制备及其对镍离子的吸附性能

以正硅酸乙酯为硅源、3-氨丙基三乙氧基硅烷为改性剂,采用溶胶-凝胶法制备了氨基改性二氧化硅气凝胶,采用FTIR、SEM、TEM和BET技术对其进行了表征,并将其用于对水中镍离子的吸附。表征结果显示,改性前后的气凝胶均具有三维多孔网络结构,比表面积分别为877.35 m²/g和357.76 m²/g,平均孔径分别为10 nm和12 nm。实验结果表明：溶液pH为4~7时改性气凝胶对镍离子均保持较高的吸附量,溶液pH为6左右时吸附量最高;Langmuir等温吸附模型能更好地描述镍离子在改性气凝胶上的吸附行为,其饱和吸附量为70.03 mg/g,改性前仅为29.05 mg/g;改性气凝胶重复使用5次后,仍保持较高的镍离子去除率,重复使用性能良好。     

Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash

Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.     

碳纳米管-海藻酸钠复合吸附材料的制备及其对高浓度Cr（Ⅲ）的吸附

以碳纳米管（CNTs）和海藻酸钠（SA）为主要原料，制备了环境友好型的复合吸附材料——CNTs-SA。采用TEM和FTIR技术对吸附材料进行了表征，并采用静态法考察了溶液pH、吸附时间、原料固液比（m（CNTs）∶V（SA））等因素对CNTs-SA吸附Cr（Ⅲ）的影响。表征结果显示，CNTs-SA表面引入了更多的—COOH和—CO基团，导致其吸附Cr（Ⅲ）的效果较CNTs有了显著的提高。实验结果表明：在室温、初始Cr（Ⅲ）质量浓度4 000 mg/L、CNTs-SA加入量21 mg/mL、溶液pH 5、吸附时间3 h、m（CNTs）∶V（SA）=1.0 mg/mL的条件下，CNTs-SA对Cr（Ⅲ）的吸附量为120 mg/g，Cr（Ⅲ）去除率为61.5%;Freundlich等温吸附方程适合描述CNTs-SA对Cr（Ⅲ）的吸附行为。     

Removal of Cr(VI) from contaminated soil by electrokinetic remediation

A new process for the removal of hexavalent chromium [Cr(VI)] contaminated soil is described. The process provides for an efficient removal of anionic chemicals from contaminated soils. Chromate anions were removed from the soil to the anodic reservoir by the moving force of electromigration. In this process, the chromate anions that accumulate in the anodic reservoir are simultaneously eliminated by using a column packed adsorbent. The adsorbent (immobilized tannin) used was chemically incorporated into cellulose. Cr(VI) was found to be adsorbed to this adsorbent efficiently. In the electrokinetic process, the pH of the aqueous solution in the anodic reservoir was decreased by the electrolysis of water. In the present study, the pH of the solution in the anodic reservoir is maintained at pH 6 by the addition of an aqueous alkaline solution during the electrokinetic process. The advantage of pH control is that it promotes the release of Cr(VI) from the soil by electromigration, thus permitting the maximum adsorption of Cr(VI) on the immobilized tannin. Simultaneous collection of Cr(VI) from the anodic reservoir leads to the protection from secondary contamination with Cr(VI).     

球形纤维素吸附剂对Cr3+吸附和解吸的研究

用静态法和动态法研究了球形纤维素吸附剂对水中 Cr3+的吸附和解吸 ,包括静态等温吸附以及各种因素对吸附的影响等 ,并探讨了吸附机理。 Cr3+的吸附容量为 2 8mg/ g,采用浓度为 1.2 mol/ L 的 HCl溶液作解吸液回收 Cr3+的综合效果较好。静态法和动态法的吸附率均达 90 %左右 ,解吸率均达 85 %以上 ,且静态法的吸附率和解吸率分别略高于动态法的吸附率和解吸率 ,但动态法耗时短 ,更符合工业化要求。     

Removal of Cr(VI) Ions from Aqueous Solutions Using Poly 3-Methyl Thiophene Conducting Electroactive Polymers

This paper deals with a new application of poly 3-methyl thiophene synthesized chemically onto sawdust (termed as P3MTh/SD) as an effective adsorbent for removal of Cr(VI) ions from aqueous solutions using column system. Chemical synthesis of poly 3-methyl thiophene was performed by addition of ferric chloride (in chloroform) as oxidant to sawdust which had previously been soaked in monomer solution. All the sorption experiments were conducted using dynamic or column system at room temperature. The effect of important parameters such as pH and initial concentration on uptake of Cr(VI) was investigated. In order to find out the possibility of the regeneration and reuse of the exhausted adsorbent, desorption studies were also performed. The currently introduced adsorbent was found to be an efficient adsorbent for removal of highly toxic and hazardous Cr(VI) ions from aqueous solutions. As our breakthrough analysis has indicated, each gram of P3MTh/SD is able to remove more than 95% of Cr(VI)ions from 300 mL of Cr(VI) polluted solution with the initial concentration of 25 mg L⁻¹ in column system. Sorption/desorption of Cr(VI) ions was found to be a highly pH dependent processes.     

白腐菌改性的中药渣对Cr（Ⅵ）的吸附性能

以白腐菌的典型菌种黄孢原毛平革菌为改性菌种，对中药渣进行改性处理，研究了改性中药渣对Cr（Ⅵ）的吸附性能。采用SEM技术对改性中药渣进行表征。研究了废水pH、改性中药渣加入量、吸附温度和吸附时间对Cr（Ⅵ）吸附效果的影响。表征结果显示，中药渣经过改性后表面出现许多孔隙，比表面积增大，为吸附Cr（Ⅵ）提供了更多的吸附位。实验结果表明：在初始Cr（Ⅵ）质量浓度50 mg/L、改性中药渣加入量5 g/L、废水pH 2、吸附温度45 ℃、吸附时间20 h的条件下，改性中药渣对Cr（Ⅵ）的去除率达99.5%，吸附量可达9.82 mg/g；改性中药渣对Cr（Ⅵ）的吸附等温线符合Langmuir等温吸附方程和Freundlich等温吸附方程；准二级动力学方程能很好地对改性中药渣吸附Cr（Ⅵ）的数据进行拟合。     

中孔活性炭对水溶液中Cr3+的吸附

采用模板法和氢氧化钾化学活化法制备出不同中孔率的中孔活性炭并用于水中Cr3+的静态吸附,探讨了中孔活性炭吸附Cr3+的影响因素.实验结果表明,当溶液pH为6.0、吸附温度为50℃、吸附时间为120min、活性炭加入量为2.0g/L以及活性炭中孔率为80.0％～90.0％时.中孔活性炭对溶液中Cr3+的去除率达到98.5％.分别采用Langmuir和Freundlich方程拟合活性炭对Cr3+吸附的等温线,发现Langmuir等温吸附模型对活性炭吸附Cr3+拟合程度更好.活性炭中孔率的增大有利于提高Cr3+的平衡吸附量,但同时还受到活性炭表面酸总量的影响.吸附Cr3+前、后活性炭的FTIR谱图表明,Cr3+与活性炭表面含氧官能团发生了离子交换反应.     

硝酸改性活性炭的制备及其对Cr（Ⅵ）

利用硝酸对颗粒活性炭进行改性，处理含铬废水，并考察了吸附时间、溶液pH、吸附剂加入量对改性活性炭吸附Cr（Ⅵ）效果的影响。实验结果表明：经过硝酸氧化改性的活性炭比表面积有所增加，官能团总量增加明显；吸附剂对Cr（Ⅵ）的去除率随振荡时间的增加而增加；对于质量浓度为10mg/L的100mLCr（Ⅵ）溶液，当溶液pH为中性，30%（体积分数）硝酸改性的颗粒活性炭的加入量为0.4g，其对Cr（Ⅵ）的最大去除率为98%。     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.