Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

Oxidative treatment of simulated dyehouse effluent by uv and near-UV light assisted Fenton's reagent

UV/Fenton, near-UV-visible/Fenton, dark Fenton, and H₂O₂/UV reactions have been used to treat simulated dyehouse effluents representing wastewater from the textile dyeing and rinsing process. Experiments were carried out in a lab - scale photochemical reactor using concentrations of 0.5–25 mM H₂O₂, 0.04-0.5 mM Fe²⁺-ion and different dilutions of textile wastewater. To assess the extent of mineralization, decolourization kinetics and the effect of different fight sources on treatment efficiency, DOC, optical density at 254 nm and 600 nm wavelength and residual H₂O₂ concentrations were measured during the course of the advanced oxidation reactions. Comparative evaluation of the obtained results revealed that the decolourization rate increased with applied H₂O₂ and Fe²⁺-ion dose as well as the strength of the synthetic textile wastewater. The best results were obtained by the near - UV/visible/Fenton process with a decolourization rate constant of 1.57 min⁻¹, a UV_254nm reduction of 97% and a DOC removal of 41% at relatively low doses of the H₂O₂ oxidant and Fe²⁺-ion catalyst within 60 min treatment time.     

An investigation into reservoir NOM reduction by UV photolysis and advanced oxidation processes

A comparison of four treatment technologies for reduction of natural organic matter (NOM) in a reservoir water was made. The work presented here is a laboratory based evaluation of NOM treatment by UV-C photolysis, UV/H(2)O(2), Fenton's reagent (FR) and photo-Fenton's reagent (PFR). The work investigated ways of reducing the organic load on water treatment works (WTWs) with a view to treating 'in-reservoir' or 'in-pipe' before the water reaches the WTW. The efficiency of each process in terms of NOM removal was determined by measuring UV absorbance at 254 nm (UV(254)) and dissolved organic carbon (DOC). In terms of DOC reduction PFR was the most effective (88% removal after 1 min) however there were interferences when measuring UV(254) which was reduced to a lesser extent (31% after 1 min). In the literature, pH 3 is reported to be the optimal pH for oxidation with FR but here the reduction of UV(254) and DOC was found to be insensitive to pH in the range 3-7. The treatment that was identified as the most effective in terms of NOM reduction and cost effectiveness was PFR.     

Removal of Cr(VI) and humic acid by using TiO2 photocatalysis

The removal efficiencies of Cr(VI) and HA, using a TiO(2)-mediated photocatalytic process, were investigated with variations in the pH, TiO(2) dosage and Cr(VI)/HA ratio. During the photocatalytic reaction, the total removal of Cr(VI) occurred through adsorption onto TiO(2), as well as its reduction to Cr(III). However, oxidation and adsorption were identified as important removal processes for the treatment of HA. Due to the anionic type adsorption onto TiO(2) and its acid-catalyzed photocatalytic reduction, the removal of Cr(VI) decreased with increasing pH, while that of HA increased with increasing pH. The TiO(2) dosage was also an important parameter for the removal of Cr(VI). As the TiO(2) dosage was increased to 2.5 g l(-1), the removal of Cr(VI) was continuously enhanced, but decreased at dosages above 3 g l(-1) due to the increased blockage of the incident UV light used for the photocatalytic reaction. The removal of Cr(VI) was greatly enhanced when the system contained both HA and Cr(VI) compared to Cr(VI) alone. Also, the removal of HA was greatly enhanced when the system contained both HA and Cr(VI) compared to HA alone. The removal of Cr(VI) was continuously enhanced as the HA concentration gradually increased; however, no further increase was observed above 20 mg l(-1) HA due to the increased absorption of the UV light. This result supports that the photocatalytic reaction, with illuminated TiO(2), could be applied to more effectively treat wastewater containing both Cr(VI) and HA than that containing a single species only.     

改性TiO2/浮石光催化去除二级出水中有机物

为了实现城市污水厂二级出水的回用,将La3+、Fe3+共掺杂TiO2/浮石光催化用于二级出水中有机物的去除。在优化工艺条件下,该方法对TOC的去除率为49.0%,对UV254的去除率为76.5%;出水BDOC/DOC值大幅度提高,由最初的0.21提高到0.56,增加了出水的可生化性;二级出水中存在着影响光催化去除有机物的因素,其中阴离子对有机物的去除有一定的抑制作用;光催化反应在通过O3强化后对有机物的去除率得到提高,TOC的去除率达到75.0%,光催化和O3氧化对有机物的去除具有协同效应;随着光催化反应次数的增加,催化剂活性有下降趋势,使用10次后TOC去除率下降到第一次使用时的16.7%,再生能够使催化活性恢复到使用前的95%,催化剂在使用15次以内稳定性较好。     

Solar photocatalytic decolorization of methylene blue in water

In this study, a photocatalytic decolorization system equipped with immobilized TiO2 and illuminated by solar light was used to remove the color of wastewater. To examine the decoloring efficiency of this system, photocatalytic decolorization of an organic dye such as methylene blue was studied as an example. The effects of light source, pH, as well as the initial concentration of dye were also investigated. It was observed that the solution of methylene blue could be almost completely decolorized by the solar light/TiO2 film process while there was about 50% color remaining with solar irradiation only. In addition, it was found that the decoloring efficiency of solution was higher with solar light irradiation than with artificial UV light irradiation, even though the artificial UV light source supplied higher UV intensity at 254 nm. The color removal rate of methylene blue with solar light irradiation was almost twice that of artificial UV light irradiation. This phenomena was mainly attributed to that some visible light range of solar light was useful for exciting the methylene blue molecules adsorbed on TiO2 film, leading to a photosensitization process undergoing and decoloring efficiency promoted. This solar-assisted photocatalytic device showed potential application for decoloring organic dyes in wastewater.     

水解酸化+A/O工艺对石化废水不同分子量有机物去除效果评价

对某典型石化企业综合污水处理厂"水解酸化+A/O"处理工艺各单元出水不同分子量区间的有机物含量及光谱特性进行了表征。研究表明,石化企业综合污水处理厂各处理单元出水DOC以分子量1 kDa的有机物为主;处理工艺对废水COD、DOC和UV254的总去除率分别为84.58%、86.22%和72.92%,分子量1 kDa、3~5 kDa、10~30 kDa、30~100 kDa的DOC去除率达90%左右,分子量5~10 kDa和100 kDa的DOC增加了28.57%和43.90%;分子量1 kDa的UV254的去除率为76.27%;水解酸化池对分子量30~100 kDa的有机物去除率达90.87%,缺氧段对分子量1~3 kDa的DOC去除率达92.86%,缺氧出水分子量3~10 kDa和30~100 kDa的DOC浓度较水解酸化出水有较大增加,好氧段对缺氧段出水中分子量30~100 kDa、5~10 kDa和3~5 kDa的有机物有很好的去除作用,去除率分别为80.85%、43.46%和72.32%,而分子量1~3 kDa的DOC浓度有所增加。各出水在260~270 nm有紫外吸收峰。各分子量区间DOC的SUVA值随处理工艺沿程增大,废水有机物芳香度提高,UV253/UV203呈减小趋势。     

Photochemical and photocatalytic degradation of gaseous toluene using short-wavelength UV irradiation with TiO2 catalyst: comparison of three UV sources

The feasibility of the use of short-wavelength UV (254+185 nm) irradiation and TiO2 catalyst for photodegradation of gaseous toluene was evaluated. It was clear that the use of TiO2 under 254+185 nm light irradiation significantly enhanced the photodegradation of toluene relative to UV alone, owed to the combined effect of photochemical oxidation in the gas phase and photocatalytic oxidation on TiO2. The photodegradation with 254+185 nm light irradiation was compared with other UV wavelengths (365 nm (black light blue lamp) and 254 nm (germicidal UV lamp)). The highest conversion and mineralization were obtained with the 254+185 nm light. Moreover, high conversions were achieved even at high initial concentrations of toluene. Catalyst deactivation was also prevented with the 254+185 nm light. Regeneration experiments with the deactivated catalyst under different conditions revealed that reactive oxygen species played an important role in preventing catalyst deactivation by decomposing effectively the less reactive carbon deposits on the TiO2 catalyst. Simultaneous elimination of photogenerated excess ozone and residual organic compounds was accomplished by using a MnO2 ozone-decomposition catalyst to form reactive species for destruction of the organic compounds.     

The degradation of dissolved organic nitrogen associated with melanoidin using a UV/H2O2 AOP

The aim of this study was to examine the simultaneous degradation of dissolved organic nitrogen (DON) and associated colour from wastewater containing melanoidins by an advanced oxidation process (AOP). UV irradiation of H2O2 was used as the mechanism to create the hydroxyl radical for oxidation. Melanoidins are large nitrogenous organic compounds that are refractory during biological wastewater treatment processes. The simultaneous degradation of DON and colour, present as a result of these compounds, was investigated using an AOP. The oxidation process was much more capable of removing colour (99% degradation), dissolved organic carbon (DOC) (50% degradation) and DON (25% degradation) at the optimal applied dose of hydrogen peroxide for the system (3300 mg l(-1)). This indicated that colour and DON removal were decoupled problems for the purpose of treating melanoidin by an AOP and thus colour removal can not be used as an indication of DON removal Colour was caused by organic molecules with molecular weight greater than 10 kDa. Oxidation caused a partial reduction of the DON (41-15% of the total dissolved nitrogen) and DOC (29-14% of the DOC) associated with the large molecular weight fraction (>10 kDa) and almost complete colour removal (87-3% of the total colour). The degraded DON was mostly accounted for by the formation of ammonia (31% of the nitrogen removed from the large fraction) and small molecular weight compounds (66% of the nitrogen removed from the large fraction). The degraded DOC appeared to be mostly mineralised (to CO2) with only 20% of the degraded compounds appearing as small molecular weight DOC.     

Photocatalytic oxidation of pesticide rinsate

Pesticide rinsate has been considered as one of the major threats for the environment. In this study, photocatalysts such as TiO2 and O3 were used to promote the efficiency of direct UV photolysis to prevent such wastewater pollution. Carbofuran (a carbamate pesticide) and mevinphos (an organophosphate pesticide) with a concentration of 100 mg/L were selected as the test pesticide rinsates. Parent pesticide compound, COD, and microtoxicity analysis were employed to investigate the effect of photocatalyst on the degradation efficiency of pesticide in rinsate. It was found that the photocatalytic oxidation process (UV/O3, UV/TiO2) showed much higher COD removal and microtoxicity reduction efficiency for pesticide rinsate than did direct UV photolysis under the imposed conditions, suggesting that photocatalytic oxidation processes such as UV/O3 and UV/TiO2 could be a better alternative to treat pesticide rinsate. In addition, it was noted that increasing the initial pH of mevinphos rinsate to a basic level was required to reach higher COD removal efficiency and positive microtoxicity reduction efficiency while it was not necessary for the treatment of carbofuran rinsate.     

土壤渗滤对有机微污染物去除性能研究

采用土壤柱试验研究了土壤渗滤对再生水中有机微污染物的去除性能。结果表明，土壤柱对再生水中的DOC、UV₂₅₄、总氮和总磷有较好的去除效果，并具有较高的抗冲击负荷的能力；土壤表层10 cm厚度对DOC的去除起主要作用；UV₂₅₄和AOX在土壤表层10 cm厚度降解效果不明显，随着深度增加去除率逐渐升高；液相色谱有机碳探测(LC-OCD)检测结果表明，土壤柱对溶解性有机物质的去除主要体现在对多糖物质的降解上，其次是有机酸类，对腐殖质也有一定的去除作用。     

光催化氧化深度处理电镀有机废水的工程化实验

采用光催化氧化联用技术对电镀有机废水进行深度处理工程化实验。探讨了uV、uV＋H2O3、uV＋H2O2＋TiO2、uV＋H2O2＋FeSO4、uV＋H2O2＋FeSO4＋TiO2、uV＋O3＋TiO2和uV＋03＋TiO2＋H2O2等体系对废水有机污染物去除率的影响。结果表明，相较于其他反应体系，uV＋O3＋TiO2＋H2O2体系具有更好的氧化效果，经碳滤处理后去除率达到90％以上，最终出水水质满足GB18918-20O2-级标准（A标准）的要求。实际运行项目偿还期5．33年，NPV〉0，内部收益率大于基准值10％。研究表明，uV＋O3＋TiO2＋H2O，体系能降低加药量，工作量及运行成本。可为电镀企业实际废水处理提供现实依据，为优化电镀废水的处理工艺提供参考。     

Photocatalytic oxidation and removal of arsenite from water using slag-iron oxide-TiO2 adsorbent

Photocatalytic oxidation of arsenite and simultaneous removal of the generated arsenate from aqueous solution were investigated. The whole process was performed using an adsorbent developed by loading iron oxide and TiO2 on municipal solid waste melted slag. The loading was carried out through chemical reactions and high-temperature process. In the removal process, arsenite was first oxidized to arsenate, and then was removed by adsorption. The oxidation of arsenite was rapid, but the adsorption of the generated arsenate was slow. A concentration of 100 mg l(-1) arsenite could be entirely oxidized to arsenate within 3 h in the presence of the adsorbent and under UV-light irradiation, but the equilibrium adsorption of the generated arsenate needed 10 h. Arsenite could also be oxidized to arsenate only by UV-light, but the reaction rate was approximately 1/3 of that of the photocatalyzed reaction. Both acidic and alkaline conditions were favorable for the oxidation reaction, and the optimum pH value for the oxidation and adsorption was proposed to be around 3. To oxidize and remove original 20 mg l(-1) or 50 mg l(-1) arsenite from aqueous solution, the necessary adsorbent amount was 2 g l(-1) or 5 g l(-1), respectively. Furthermore, the surface properties of the adsorbent were examined and the oxidation mechanism of arsenite was discussed. It is believed that the adsorbent developed in this study is efficient, cost-effective and environment-friendly for application in arsenic-contaminated wastewater treatment.     

Monitoring of effluent DOM biodegradation using fluorescence, UV and DOC measurements

The potential of effluent DOM to undergo microbial degradation was assessed in batch experiments. Effluent samples from Haifa wastewater treatment plant and Qishon reservoir (Greater Haifa wastewater reclamation complex, Israel) were incubated either with effluent or soil microorganisms for a period of 2-4 months and were characterized by dissolved organic carbon contents (DOC), UV(254) absorbance and by fluorescence excitation-emission matrices. Three main fluorescence peaks were identified that can be attributed to humic/fulvic components and "protein-like" structures. During biodegradation, specific fluorescences (F/DOC) of the three peaks were increased at various extents, suggesting selective degradation of non-fluorescing constituents. In some cases increase in the effluent fluorescence (F) was observed thus proposing (i) the formation of new fluorescing material associated with DOM biodegradation and/or (ii) degradation of certain organic components capable of quenching DOM fluorescence. Based on the ratio between fluorescence intensity and UV(254), different biodegradation dynamics for fluorescent DOM constituents as compared with other UV-absorbing molecules was delineated. Overall, about 50% of the total DOM was found to be readily degradable such that residual resistant DOC levels were between 8 and 10 mg l(-1). Enhanced levels of residual DOM in effluent-irrigated soils may contribute to the DOM pool capable of carrying pollutants to groundwater.     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理，考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响，确定出O3氧化反应的最佳工艺参数为：接触时间40min，溶液pH8．5，反应温度25℃，此条件下废水COD及UV254的去除率最高可达47．14％和73．47％；H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高，但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明，单纯采用COD作为评价指标，并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

NOM characteristics and treatabilities of ozonation processes

The objectives of this study were intended to evaluate the effects of the characteristics of natural organic matter on the treatabilities of ozonation, coagulation, filtration, and granular activated carbon processes. The ultra-violet absorbance (UV254) was used as a surrogate parameter to assess each process in reducing the disinfection by-product formation potential (DBPFP). The results indicate that the DBPFP varies with the sources of water samples and treatment processes, but is closely related to the measurement of UV254/DOC. Coagulation/sedimentation can eliminate large molecular weight organic fractions. Both pre- and post-ozonation processes can reduce some of DBP precursors than the conventional treatment process, and are more reliable for reducing the overall DBPFP.     

土壤-纳滤系统处理再生水补充地下水的研究

为充分保障再生水回灌地下时的水质安全、提供高质量地下水资源,在土壤处理系统中嵌入纳滤技术强化对再生水的处理效果,并初步探讨土壤系统作为前处理对纳滤膜污染的控制机理.结果表明,未采用臭氧氧化预处理前,土壤处理对再生水DOC和UV254的平均去除率分别为22%和20%.臭氧氧化对UV254的平均去除率为51%,并将土壤对D...     

Photocatalytic degradation of the herbicide erioglaucine in the presence of nanosized titanium dioxide: comparison and modeling of reaction kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO2 nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO2 system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir-Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm-1 and 0.984 ppm min-1, respectively. In this work, we also compared the reactivity between the commercial TiO2 Degussa P-25 and a rutile TiO2. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO2 for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO2 process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO2.     

直接过滤-臭氧-生物活性炭工艺用于城市污水二级处理出水深度处理的研究

采用砂滤-臭氧-生物活性炭工艺在北京市某污水处理厂开展了以污水再生回用为目的的城市污水深度处理中试研究。在臭氧消耗量5mg／L，接触时间20min，生物活性炭空床停留时间（EBCT）为20min的条件下，出水浊度为1．5NTU左右，色度接近0，UV254从0．162cm^-1降低到0．08cm^-1，DOC和CODMn分别从10．1mg／L和12．8mg／L降低到6mg／L左右。由于对生物活性炭柱进行了曝气供氧，NH4^- N从40mg／L降低到5mg／L左右。