TH- 880Ⅲ型微电脑烟尘平行采样仪的特点及问题

ＴＨ-880Ⅲ型微电脑烟尘平行采样仪主要用于对各种燃煤锅炉和工业炉窑烟尘进行全自动等速采样,它是武汉天虹智能仪表厂的Ⅱ型仪器的改进型。它能全自动跟踪烟气进行等速采样,抽气泵与主机一体化,操作平面为全中文菜单,操作简单,大大降低了监测人员的劳动强度。1　ＴＨ-88...     

燃煤电厂石膏雨污染排放实测

对上海市8台燃煤机组开展了石膏雨和相关污染物排放监测,考察部分燃煤电厂石膏雨排放对周边居民生活和电厂生产造成的影响。结果表明,采用GGH并加热到一定温度,同时对除雾器进行优化的机组烟尘和可凝结颗粒物浓度均较低,石膏雨沉降和液滴均未检出,无冷凝回流液;虽然装有湿式电除尘器和GGH的机组石膏雨沉降未检出,但液滴浓度较高;仅装有湿式电除尘器的2台机组中1台检出石膏雨沉降;对照机组石膏雨沉降和液滴浓度均较高。建议电厂提升排烟温度,同时采取措施消除烟气中石膏夹带,彻底消除石膏雨,在标准制定时应充分考虑目前燃煤电厂多种污染物排放情况及其对环境的影响,尤其是石膏雨和可凝结颗粒物,制定相应的监测方法和评价体系,将其纳入火电厂排放标准中。     

燃煤机组烟气脱硫超低排放技术研究

文章重点介绍了目前我国燃煤机组烟气脱硫超低排放技术,并列举了一些已经实现烟气脱硫超低排放技术改造的燃煤机组工程实例和运行效果。     

燃煤锅炉湿法脱硫烟气中颗粒物排放特征

选择北京市典型燃煤锅炉进行研究,结果表明:烟气中可凝结颗粒物在总颗粒物中占有较高比例,供热燃煤锅炉总颗粒物排放水平明显高于电厂燃煤锅炉;颗粒物中水溶性离子含量较高,供热燃煤锅炉硫酸根比例尤其显著;烟气总颗粒物中存在大量不稳定的易被氧化的组分;同为燃煤源,不同的烟气净化工艺排放的PM2.5组分特征差异明显;现有标准和技术规范存在不足,无法满足全面、准确监测污染源排放总颗粒物的实际需要。建议建立总颗粒物、可凝结颗粒物的监测技术规范,全面测算燃煤锅炉硫、氮化合物排放情况,科学评估脱硫及脱硝效率。     

家用炉灶燃煤过程单环芳香烃释放初步研究

利用多层吸附管采样和热脱附/色谱/质谱系统研究了家用炉灶燃煤过程单环芳烃释放情况。结果显示,燃煤烟气中的单环芳烃组分主要以苯、甲苯为主,平均浓度分别达到1672.3和1631.3μg/m3。从烟气中单环芳烃水平来看,家用炉灶燃煤释放的单环芳烃大大超过电站燃煤和生物质能燃烧释放;烟气中的单环芳烃的组成形式也有别于电站燃煤、生物质能燃烧、机动车排放和油漆挥发的单环芳烃。研究中还分析了煤在氦气环境下热解释放的单环芳烃,并与家用炉灶燃煤释放的单环芳烃进行了比较。     

燃煤锅炉烟气中CPM与水溶性离子监测方法及应用研究

建立燃煤锅炉烟气可凝聚颗粒物(CPM)与水溶性离子监测采样方法,并应用于北京市典型烟气净化工艺燃煤锅炉排放监测。结果表明,北京市燃煤锅炉烟气中总颗粒物(TPM)基准排放质量浓度最高达82.4 mg/m3,最低14.0 mg/m3,其中CPM占TPM的43.5%~92.2%,水溶性离子对TPM的贡献水平为31.4%~62.2%。烟温对水溶性离子的分布形态有显著影响,进而影响TPM中可过滤颗粒物(FPM)和CPM的分配比例。颗粒物和水溶性离子的排放与烟气含湿量之间无显著相关性,而与燃煤锅炉烟气脱硫除尘净化工艺和脱硫产物的溶解度及其脱除方式密切相关。     

烟气黑度监测中应注意的问题

烟气中林格曼黑度的测定是通过将排放源出口处烟气颜色与林格曼烟气浓度图比较,当某一排气颜色与其中色块接近时,就认定烟尘浓度与该色块的黑度等级一致,该方法已广泛用于环境保护等监测部门。国家颁布的有关炉窑大气污染物排放标准中对烟气黑度作的规定和解释见表1。     

上海市中小锅炉燃煤含硫率监测方案的研究

针对燃煤含硫率监测的瓶颈问题,提出了通过对锅炉烟气二氧化硫排放浓度以及排放量获得的监测数据,推算得到燃煤含硫率的方案.     

基于实测的燃煤电厂烟气中汞排放水平浅析

简述汞污染和控制问题成为环境问题的新热点和前沿研究领域,介绍中国燃煤电厂烟气汞监测试点的基本情况。分析江苏省7家燃煤电厂煤中汞及烟气中汞排放水平,提出利用现有的除尘、脱硫、脱硝设施,能满足《火电厂大气污染物排放标准》中汞的排放限值要求。     

超低排放下燃煤电厂颗粒物排放特征分析研究

选取6家经过超低排放改造的燃煤电厂,对湿法脱硫(WFGD)和湿式电除尘器(WESP)进出口烟气中TPM、PM_(10)、PM_(2.5)、PM_1进行测试,分析研究超低排放下燃煤电厂颗粒物的排放特征及电除尘器后净化设备对颗粒物的脱除效果。结果表明,6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放浓度分别为0.75~2.36、0.71~2.12、0.65~1.96、0.51~1.57 mg/m~3。分析烟气中颗粒物粒径分布可知,除尘器后,PM10占TPM质量比低于40%,且比例随烟气经过WFGD和WESP而逐渐降低。WFGD对PM2.5有较好的脱除效果,而WESP对PM1脱除效果显著。为满足超低排放标准,6家电厂除尘器后脱除设备综合除尘效率大多在85%以上。计算得到6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放因子,与超低排放改造之前同等级燃煤电厂相比,6家电厂不同粒径颗粒物排放因子均显著降低,也远低于西方发达国家燃煤电厂颗粒物排放因子。     

生活垃圾与危险废物的焚烧工艺及污染防治措施比较

比较、归纳、总结了生活垃圾和工业危废焚烧项目在生产工艺、污染源产生及治理、污染物排放标准等方面的异同点,提出必须重视废气排污口设施与在线监测仪器的安装,应完善事故防范措施与应急预案等检查要求,为环保部门验收监测、监督管理工作提供技术支持.     

涪陵页岩气田一期工程环境影响调查

采用现场调研与实地监测相结合的方法对涪陵页岩气田一期工程污染源和区域环境质量现状进行深入调查研究,剖析涪陵页岩气开发对环境产生的影响。结果表明,涪陵页岩气田开发过程中废水实行循环利用,钻屑固体废物固化填埋,企业环保措施基本落实,短期内页岩气开发未对区域环境产生明显不良影响。指出修建井场、池体、道路等设施对生态环境具有一定影响,且随着时间推移,钻屑固化填埋对周围土壤及水环境也具有潜在影响。     

燃煤电厂烟气排放过程监控系统设计与应用

介绍了燃煤电厂烟气排放过程（工况）监控系统的架构，排放过程监控子系统、参数监测子系统和数据采集传输子系统的实现方式，过程监控采集参数选择方法，模型建立步骤与验证方法。结合实际应用，分析如何判定脱硫设施运转正常，烟气参数监测是否正确，并提出了做好过程监控系统工作的相关建议。     

Mercury and other elements in lichens near the INA Naftaplin gas treatment plant, Molve, Croatia

This paper describes the use of epiphytic lichens as bioindicators for spatial monitoring of mercury and other elements in air near the natural gas treatment facilities at Molve, Croatia. It is well known that at this location the concentration of mercury in natural gas is very high and therefore it has to be removed from natural gas before further processing in order to prevent technological and environmental problems. In order to monitor the efficiency of an industrial facility for removal of mercury from natural gas, mercury measurements in air and lichens were performed during 9 months in 1997/1998. In situ lichens Parmelia sulcata, Xantoria parientina and Hypogymnia physodes and transplanted lichen species Hypogymnia physodes were used. A good correlation between mercury concentrations in air and lichens was found. The concentrations of barium and bromium were also significantly elevated in transplanted lichens, most probably related to technological process at the gas treatment plant and/or other geological factors. It was confirmed that lichens can successfully be used as bioindicators, provided a careful experiment is designed, particularly the amount of lichens transplanted, the duration of exposure and the initial levels and homogeneity of transplanted lichens.     

Environmental impact of coal mining and coal seam gas production on surface water quality in the Sydney basin,Australia

The extraction of coal and coal seam gas (CSG) will generate produced water that, if not adequately treated, will pollute surface and groundwater systems. In Australia, the discharge of produced water from coal mining and related activities is regulated by the state environment agency through a pollution licence. This licence sets the discharge limits for a range of analytes to protect the environment into which the produced water is discharged. This study reports on the impact of produced water from coal mine activities located within or discharging into high conservation environments, such as National Parks, in the outer region of Sydney, Australia. The water samples upstream and downstream from the discharge points from six mines were taken, and 110 parameters were tested. The results were assessed against a water quality index (WQI) which accounts for pH, turbidity, dissolved oxygen, biochemical oxygen demand, total dissolved solids, total phosphorus, nitrate nitrogen and E .coli. The water quality assessment based on the trace metal contents against various national maximum admissible concentration (MAC) and their corresponding environmental impacts was also included in the study which also established a base value of water quality for further study. The study revealed that impacted water downstream of the mine discharge points contained higher metal content than the upstream reference locations. In many cases, the downstream water was above the Australia and New Zealand Environment Conservation Council and international water quality guidelines for freshwater stream. The major outliers to the guidelines were aluminium (Al), iron (Fe), manganese (Mn), nickel (Ni) and zinc (Zn). The WQI of surface water at and downstream of the discharge point was lower when compared to upstream or reference conditions in the majority of cases. Toxicology indices of metals present in industrial discharges were used as an additional tool to assess water quality, and the newly proposed environmental water quality index (EWQI) lead to better trend in the impact of coal and coal seam gas mining activities on surface water quality when compared to the upstream reference water samples. Metal content limits were based on the impact points assigned by the Agency for Toxic Substances and Disease Registry, USA. For environmental and health impact assessment, the approach used in this study can be applied as a model to provide a basis to assess the anthropogenic contribution from the industrial and mining activities on the environment.     

能源结构变化对兰州市大气质量的影响

将2001—2010年的主要能源材料消耗、主要污染物变化及主要行业分布进行了相关性分析,结果表明:兰州市大气4种主要污染物中除烟尘呈下降趋势外,废气总量、SO2、NOx仍呈上升趋势;主要污染源为燃煤,主要污染行业为电力、蒸汽热水产供业;废气和SO2排放总量与燃煤和燃气呈强正相关,而NOx排放只与燃气呈强正相关。建议发挥兰州地域优势,加大以水电供应为主的能源结构调整,对改善当地空气质量有重要价值。     

An Analogy on Assessment of Urban Air Pollution in Turkey Over the Turn of the Millennium (1992–2001)

Rapid industrialization and urbanization in Turkey, especially over the last twenty five years, has provided better living standards to its residents, but it also caused a decrease in environmental quality. In late 1970's, air quality monitoring activities were started in some major cities by individual researchers in Turkey. It was just around the 1990's that a countrywide program on continuous air pollution monitoring in major province centers and selected large towns was launched. The impact of air pollution on people depend on various factors, such as existence and magnitude of coal powered energy generation plants, type of urban heating and their efficiency, and the numbers and specifications of vehicles. In this study, current Turkish urban air quality over the turn of the Millennium (1992–2001) is studied in the light of the country's worst cities in terms of outdoor air quality, the number of upper respiratory diseases, sinusitis, bronchitis, and pneumonia cases in these provinces reported by the state medical treatment facilities in 2001. The population that is under outdoor urban air pollution hazard was computed. A comparative analysis between the provinces that use natural gas and others that use fossil fuels was also completed in order to project monetary gains if the studied provinces will transform their indoor heating and industrial operations to be run by natural gas or other cleaner energy sources. If natural gas use in air polluted urban centers could be realized in the near future, approximately 212 to 350 million US dollars per annum could to be saved just by reducing health related problems caused by outdoor air pollution.     

Developing a Decision-Support System for Waste Management in Aluminum Production

Industrial enterprises constitute a major portion of the world’s economy, as well as a large proportion of a country’s businesses and total employment. In Turkey, industrial enterprises are underdeveloped in terms of knowledge, skill, capital, and particularly accessing and benefiting from the advantages provided by modern information and communication technologies. Aluminum manufacturing has been reported to be the largest industry in Turkey with respect to production volumes and application fields. However, aluminum production is known to be an important contributor to environmental pollution, and the relative contribution of other related enterprises to the total industrial environmental impact is unknown. Environmental pollution sources can typically be classified into three categories: gaseous emissions, solid wastes, and wastewaters. The types of wastes produced by aluminum production vary based on the process line used, the variety of target products produced, and the production capacity of a given plant. As the capacities of facilities grow, the type and amount of waste become more variable. Therefore, the primary objective of this study is to determine the priority of each waste type in aluminum manufacturing industries. This study was conducted in the Industrial Zone of Kayseri in Turkey. Three different facilities that range in size from large to small based on their production volume, plant capacity, and variety of production are selected for this study. The priority of waste types was determined by combining the AHP and PROMETHEE II multicriteria decision methods. While wastewater was categorized as having the highest priority in large facilities, solid waste was determined to be the highest priority in medium and small facilities.     

Biomonitoring of polycyclic aromatic hydrocarbons in urban and industrial environments of the Western Black Sea Region,Turkey

This research was carried out in the cities of Zonguldak and Eregli, which have been characterized as urban and industrial environments of the Western Black Sea Region, Turkey, in order to assess the contamination of polycyclic aromatic hydrocarbons (PAHs) using mosses as biomonitors. The methodology involved the collection of moss samples (Hypnum cupressiforme), ultrasonic extraction with dichloromethane, cleanup using silica gel and analysis by liquid chromatography with ultraviolet detection. The total PAH concentrations ranged from 78.1 to 1693.5 ng g^?1 in Zonguldak and from 15.2 to 275.1 ng g^?1 in Eregli. The total PAH concentration in Eregli was about six times lower than that in Zonguldak, revealing the importance of switching from coal to natural gas in residential heating. The diagnostic ratios and the correlation analysis have indicated that coal combustion and traffic emissions were the major PAH sources at both sites. The contour maps were constructed for the determination of spatial distributions of total PAHs, and it was shown for Zonguldak as well as for Eregli that the PAH pollution was much more predominant in highly populated regions. Moving away from the city centres, a gradual decrease in PAH pollution rates was observed.